What are the three major types of reinforcement used in prestressing?

What are the three major types of reinforcement used in prestressing?
by

1 Answer

Answer :

i) Spalling reinforcement Spalling stresses are established behind the loaded area of anchor blocks and this causes breaking away of surface concrete. These stresses are induced by strain incompatibility with Poisson’s effects or by the shape of stress trajectories.
(ii) Equilibrium reinforcement Equilibrium   reinforcement   is   required   where   there   are   several   anchorages   in   which prestressing loads are applied sequentially.
(iii) Bursting Reinforcement Tensile stresses are induced during prestressing operation and the maximum bursting stress occurs where the stress trajectories are concave towards the line of action of the load. Reinforcement is needed to resist these lateral tensile forces.
by

Related questions

In prestressing work, if more than one wire or strand is included in the same duct, why should all wires/strands be stressed at the same time?

Description : In prestressing work, if more than one wire or strand is included in the same duct, why should all wires/strands be stressed at the same time?

Last Answer : If wires/strands are stressed individually inside the same duct, then those stressed strand/wires will bear against those unstressed ones and trap them. Therefore, the friction of the trapped wires is high and is undesirable.

Under what situation shall engineers use jacking at one end only and from both ends in prestressing work?

Description : Under what situation shall engineers use jacking at one end only and from both ends in prestressing work?

Last Answer : During prestressing operation at one end, frictional losses will occur and the prestressing force decreases along the length of tendon until reaching the other end. These frictional losses include the ... if the total span length is sufficiently long, jacking from both ends should be considered.

In the design of a simply supported skew bridge, which direction of reinforcement should be provided?

Description : In the design of a simply supported skew bridge, which direction of reinforcement should be provided?

Last Answer : In the conventional design of steel reinforcement for a simply supported skew bridge, a set of reinforcement is usually placed parallel to free edge while the other set is designed parallel ... ). In this way, considerable savings would be obtained from the orthogonal arrangement of reinforcement.

What is sucker deck principle for variable depth bridge decks?

Description : What is sucker deck principle for variable depth bridge decks?

Last Answer : For a variable depth bridge deck, the depth of continuous multi­span bridge deck is increased in pier supports and this absorbs sagging moments in the ... of arches and curved soffit rather than boring uniform deck alignment. Reference is made to Brian Pritchard (1992).

How do engineer determine the number of cells for concrete box girder bridges?

Description : How do engineer determine the number of cells for concrete box girder bridges?

Last Answer : If the depth of a box girder bridge exceeds 1/6 or 1/5 of the bridge width, then it is recommended to be designed as a single cell box girder bridge. However, if the bridge depth is ... improvement in transverse load distribution when the number of cells of box girder is increased to three or more.

Should raking piles of a bridge abutment be placed under an embankment?

Description : Should raking piles of a bridge abutment be placed under an embankment?

Last Answer : For a bridge abutment to be supported on raking piles with different orientations, the movement between the ground and the pile group is difficult to predict. For instance, if some of the raking ... experience severe bending moment and damage the piles as recommended by Dr. Edmund C Hambly (1979).

Polytetrafluoroethylene (PTFE) is commonly used in sliding bearings. Why?

Description : Polytetrafluoroethylene (PTFE) is commonly used in sliding bearings. Why?

Last Answer : The choice of sliding surface of bearings is of vital importance because the sliding surfaces generate frictional forces which are exerted on the bearings and substructure of the bridge. For ... be designed with dimples to avoid the lubricant from squeezing out under repeated translation movements.

What are the shortcomings of grillage analysis which is commonly used in structural analysis of bridges?

Description : What are the shortcomings of grillage analysis which is commonly used in structural analysis of bridges?

Last Answer : Grillage analysis suffers from the following shortcomings based on E. C. Hambly: (i) For coarse mesh, torques may not be identical in orthogonal directions. Similarly, twists may differ in ... moment in an element depends on the curvatures in the beam's direction and its orthogonal direction.

Under what situation should engineers use pot bearings instead of elastomeric bearings?

Description : Under what situation should engineers use pot bearings instead of elastomeric bearings?

Last Answer : In the event of high vertical loads combined with large angle of rotations, rubber bearings are undesirable when compared with pot bearings. For instance, elastomeric ... bearings are better alternatives than elastomeric bearings in such an scenario as suggested by David J. Lee.

In joints of precast concrete bridge segments, what are the functions of applying epoxy adhesive?

Description : In joints of precast concrete bridge segments, what are the functions of applying epoxy adhesive?

Last Answer : Epoxy adhesive is applied in these joints for the following purposes according to International Road Federation (1977): (i) It seals up the joints completely between precast concrete segments to protect the ... in transferring of shear between the joints in case a large single shear key is used.

What are the functions of grout inside tendon ducts?

Description : What are the functions of grout inside tendon ducts?

Last Answer : Grout in prestressing works serves the following purposes: (i) Protect the tendon against corrosion. (ii) Improve the ultimate capacity of tendon. (iii) Provide a bond between the structural member and the tendon. (iv) In case of failure, the anchorage is not subject to all strain energy.

Why is the span length ratio of end span/approach span to its neighboring inner spans usually about 0.75?

Description : Why is the span length ratio of end span/approach span to its neighboring inner spans usually about 0.75?

Last Answer : From aesthetic point of view, an odd number of spans with a decrease in length in the direction of abutment is desirable. Moreover, spans of equal length are found to be boring. However, the ... the last span in a continuous bridge while approach span refers top the first span of a bridge.

What is the advantage of sliding bearings over roller bearings?

Description : What is the advantage of sliding bearings over roller bearings?

Last Answer : In roller bearing for a given movement the roller bearing exhibit a change in pressure centre from its original position by one­half of its movement based on David J. Lee. However, with sliding ... built in the substructure. It follows that there is no change in pressure center after the movement.

Are diaphragms necessary in the design of concrete box girder bridges?

Description : Are diaphragms necessary in the design of concrete box girder bridges?

Last Answer : Diaphragms are adopted in concrete box girder bridges to transfer loads from bridge decks to bearings. Since the depth of diaphragms normally exceeds the width by two times, they are usually designed ... In fact, diaphragms also contribute to the provision of torsional restraint to the bridge deck.

In the construction of a two­span bridge (span length = L) by using span­by­span construction, why is a length of about 1.25L bridge segment is constructed in the first phase of construction?

Description : In the construction of a two­span bridge (span length = L) by using span­by­span construction, why is a length of about 1.25L bridge segment is constructed in the first phase of construction?

Last Answer : Basically, there are mainly three reasons for this arrangement: (i) The permanent structure is a statically indeterminate structure. During construction by using span­by­span construction, if the ... 25L from the first pier where there is relatively more space to accommodate prestressing works.

In a curved prestressed bridge, how should the guided bearings in piers of the curved region be oriented with respect to the fixed bearing in abutment?

Description : In a curved prestressed bridge, how should the guided bearings in piers of the curved region be oriented with respect to the fixed bearing in abutment?

Last Answer : To determine the orientation of guided bearings, one should understand the movement of curved region of a prestressed bridge. Movement of prestress and creep are tangential to the curvature of the ... large, temporary freedom of movement at the guided bearings has to be provided during construction.

How to determine the size of elastomeric bearings?

Description : How to determine the size of elastomeric bearings?

Last Answer : For elastomeric bearing, the vertical load is resisted by its compression while shear resistance of the bearing controls the horizontal movements. The design ... and fatigue damage. The vertical stiffness of bearings is obtained by inserting sufficient number of steel plates.

In the design of elastomeric bearings, why are steel plates inserted inside the bearings?

Description : In the design of elastomeric bearings, why are steel plates inserted inside the bearings?

Last Answer : For elastomeric bearing to function as a soft spring, the bearing should be allowed for bulging laterally and the compression stiffness can be increased by limiting the amount of lateral bulging. To ... , the presence of metal plates does not affect the shear stiffness of the elastomeric bearings.

Sometimes the side of concrete bridges is observed to turn black in colour. What is the reason for this phenomenon?

Description : Sometimes the side of concrete bridges is observed to turn black in colour. What is the reason for this phenomenon?

Last Answer : In some cases, it may be due to the accumulation of dust and dirt. However, for the majority of such phenomenon, it is due to fungus or algae growth on concrete bridges. After rainfall, the ... help to solve this problem. Reference is made to Sandberg Consulting Engineers Report 18380/X/01.

What are the advantages of assigning the central pier and the abutment as fixed piers?

Description : What are the advantages of assigning the central pier and the abutment as fixed piers?

Last Answer : (i) For abutment pier to be assigned as fixed pier while the bridge is quite long, the longitudinal loads due to earthquake are quite large. As the earthquake loads are resisted by fixed piers, the size of ... Therefore, the size of movement joints can be reduced significantly.

In bridge widening projects, the method of stitching is normally employed for connecting existing deck to the new deck. What are the problems associated with this method in terms of shrinkage of concrete?

Description : In bridge widening projects, the method of stitching is normally employed for connecting existing deck to the new deck. What are the problems associated with this method in terms of shrinkage of concrete?

Last Answer : In the method of stitching, it is a normal practice to construct the widening part of the bridge at first and let it stay undisturbed for several months. After that, concreting will then be ... Stitching refers to formation of a segment of bridge deck between an existing bridge and a new bridge.

In incremental launching method of bridge construction, what are the measures adopted to enhance sufficient resistance of the superstructure during the launching process?

Description : In incremental launching method of bridge construction, what are the measures adopted to enhance sufficient resistance of the superstructure during the launching process?

Last Answer : i) During the launching process the leading edge of the superstructure is subject to a large hogging moment. In this connection, steel launching nose typically about 0.6­0.65 times span length is ... . iii)For very long span bridge, temporary piers are provided to limit the cantilever moment.

What is “preset” during installation of bridge bearings?

Description : What is “preset” during installation of bridge bearings?

Last Answer : Preset is a method to reduce the size of upper plates of sliding bearings in order to save the material cost. The normal length of a upper bearing plate should be composed of the ... of a certain distance of sliding bearings with respect to upper bearing plates during installation of bearings.

The system in which high tensile alloy steel bars (silica manganese steel) are used as prestressing tendons, is known as (A) Freyssinet system (B) Magnel-Blaton system (C) C.C.L. standard system (D) Lee-McCall system

Description : The system in which high tensile alloy steel bars (silica manganese steel) are used as prestressing tendons, is known as (A) Freyssinet system (B) Magnel-Blaton system (C) C.C.L. standard system (D) Lee-McCall system

Last Answer : Answer: Option D

A simply supported rectangular beam is uniformly loaded and is prestressed. The tendon provided for prestressing should be (a) Straight, above centroidal axis (b) Straight, below centroidal axis (c) parabolic, with convexity upward (d) Parabolic, with convexity downward

Description : A simply supported rectangular beam is uniformly loaded and is prestressed. The tendon provided for prestressing should be (a) Straight, above centroidal axis (b) Straight, below centroidal axis (c) parabolic, with convexity upward (d) Parabolic, with convexity downward

Last Answer : (d) Parabolic, with convexity downward

In case of Magnel- Blaton system of prestressing, each sandwich plate can generally anchor (a) 6 wires (b) 8 wires (c) 10 wires (d) 16 wires

Description : In case of Magnel- Blaton system of prestressing, each sandwich plate can generally anchor (a) 6 wires (b) 8 wires (c) 10 wires (d) 16 wires

Last Answer : (a) 6 wires

Define Prestressed concrete and state types of prestressing steel.

Description : Define Prestressed concrete and state types of prestressing steel.

Last Answer : Prestressed concrete: Prestressed concrete is basically a concrete in which internal stresses of a suitable magnitude and distribution are deliberately introduced so that the stresses resulting from external loads are ... 1962, and. 4) Uncoated stress relieved strand conforming to IS: 6006-1970. 

What Reinforcements Are Used In The Process Of Prestressing?

Description : What Reinforcements Are Used In The Process Of Prestressing?

Last Answer : Answer : The major types of reinforcements used in prestressing are:  Spalling Reinforcement: The spalling stresses leads to stress behind the loaded area of the anchor blocks. This results in the ... of load. In order to reduce such stresses reinforcements in the form of bursting is required.

Explain freyssinet system of prestressing with respect to process and application with sketches.

Description : Explain freyssinet system of prestressing with respect to process and application with sketches.

Last Answer : Process: - 1. The freyssinet system was the first to be introduced among the post - tensioned system high tensile steel wires 5mm to 8mm diameter about 12 in number are arranged to form a group into a cable ... gas (LNG) storage tank 4. Off share platforms. 5. Wind turbine towers etc.

In a slab, the pitch of the main reinforcement should not exceed its effective depth (A) Three times (B) Four times (C) Five times (D) Two times

Description : In a slab, the pitch of the main reinforcement should not exceed its effective depth (A) Three times (B) Four times (C) Five times (D) Two times

Last Answer : Answer: Option A

Minimum pitch of transverse reinforcement in a column is (A) The least lateral dimension of the member (B) Sixteen times the smallest diameter of longitudinal reinforcement bar to be tied (C) Forty-eight times the diameter of transverse reinforcement (D) Lesser of the above three values

Description : Minimum pitch of transverse reinforcement in a column is (A) The least lateral dimension of the member (B) Sixteen times the smallest diameter of longitudinal reinforcement bar to be tied (C) Forty-eight times the diameter of transverse reinforcement (D) Lesser of the above three values

Last Answer : Answer: Option D

in a simply supported slab, the pitch of distribution reinforcement should not be more than_____________the effective depth of slab or 60cm which ever is smaller. (a) Double (b) Three times (c) Five times (d) Six times

Description : in a simply supported slab, the pitch of distribution reinforcement should not be more than_____________the effective depth of slab or 60cm which ever is smaller. (a) Double (b) Three times (c) Five times (d) Six times

Last Answer : (c) Five times

The pitch of bars of main reinforcement in slab should not exceed ________the effective depth of slab. (a) Double (b) Three times (c) Five times (d) Six times

Description : The pitch of bars of main reinforcement in slab should not exceed ________the effective depth of slab. (a) Double (b) Three times (c) Five times (d) Six times

Last Answer : (b) Three times

In slabs the Maximum horizontal distance between parallel main reinforcement should not exceed i.Three times effective depth ii Five times effective depth iii 300mm iv 450 mm [ A ] i and iii [ B ] i and iv [ C ] ii and iii [ D ] ii and iv

Description : In slabs the Maximum horizontal distance between parallel main reinforcement should not exceed i.Three times effective depth ii Five times effective depth iii 300mm iv 450 mm [ A ] i and iii [ B ] i and iv [ C ] ii and iii [ D ] ii and iv

Last Answer : [ A ] i and iii

The Maximum spacing of Secondary reinforcement in slabs should be [ A ] Less than 450 mm [ B ] Less than 300 mm [ C ] Smaller of three times the effective depth and 450 mm [ D ] Smaller of five times the effective depth and 450 mm

Description : The Maximum spacing of Secondary reinforcement in slabs should be [ A ] Less than 450 mm [ B ] Less than 300 mm [ C ] Smaller of three times the effective depth and 450 mm [ D ] Smaller of five times the effective depth and 450 mm

Last Answer : [ D ] Smaller of five times the effective depth and 450 mm

The Maximum spacing of Main reinforcement „m‟ slabs shall be [ A ] Less than three times of the effective depth [ B ] Less than 300mm [ C ] Smaller of (a) and (b) [ D ] Greater of (a) and (b)

Description : The Maximum spacing of Main reinforcement „m‟ slabs shall be [ A ] Less than three times of the effective depth [ B ] Less than 300mm [ C ] Smaller of (a) and (b) [ D ] Greater of (a) and (b)

Last Answer : [ C ] Smaller of (a) and (b)

A teacher’s major contribution towards the maximum self-realization of the student is affected through: Options: A) Constant fulfilment of the students’ needs B) Strict control of class-room activities C) Sensitivity to students’ needs, goals and purposes D) Strict reinforcement of academic standards

Description : A teacher's major contribution towards the maximum self-realization of the student is affected through: Options: A) Constant fulfilment of the students' needs B) Strict control of class-room ... C) Sensitivity to students' needs, goals and purposes D) Strict reinforcement of academic standards

Last Answer : C) Sensitivity to students’ needs, goals and purposes 

The teacher's major contribution towards the maximum self-realization of the child is best affected through Options: A) Constant fulfilment of the child's needs B) Strict control of class-room activities C) Sensitivity to pupil needs, goals and purposes D) Strict reinforcement of a academic standards

Description : The teacher's major contribution towards the maximum self-realization of the child is best affected through Options: A) Constant fulfilment of the child's needs B) Strict control of class-room ... C) Sensitivity to pupil needs, goals and purposes D) Strict reinforcement of a academic standards

Last Answer : C) Sensitivity to pupil needs, goals and purposes 

A teacher’s major contribution towards the maximum selfrealization of the student is affected through: (A) Constant fulfilment of the students’ needs (B) Strict control of class-room activities (C) Sensitivity to students’ needs, goals and purposes (D) Strict reinforcement of academic standards

Description : A teacher’s major contribution towards the maximum selfrealization of the student is affected through: (A) Constant fulfilment of the students’ needs (B) Strict control of class-room activities (C) Sensitivity to students’ needs, goals and purposes (D) Strict reinforcement of academic standards

Last Answer : (C) Sensitivity to students’ needs, goals and purposes

The shear reinforcement in R.C.C. is provided to resist (A) Vertical shear (B) Horizontal shear (C) Diagonal compression (D) Diagonal tension

Description : The shear reinforcement in R.C.C. is provided to resist (A) Vertical shear (B) Horizontal shear (C) Diagonal compression (D) Diagonal tension

Last Answer : Answer: Option D

The amount of reinforcement for main bars in a slab, is based upon (A) Minimum bending moment (B) Maximum bending moment (C) Maximum shear force (D) Minimum shear force

Description : The amount of reinforcement for main bars in a slab, is based upon (A) Minimum bending moment (B) Maximum bending moment (C) Maximum shear force (D) Minimum shear force

Last Answer : Answer: Option B

Though the effective depth of a T-beam is the distance between the top compression edge to the centre of the tensile reinforcement, for heavy loads, it is taken as (A) 1/8th of the span (B) 1/10th of the span (C) 1/12th of the span (D) 1/16th of the span

Description : Though the effective depth of a T-beam is the distance between the top compression edge to the centre of the tensile reinforcement, for heavy loads, it is taken as (A) 1/8th of the span (B) 1/10th of the span (C) 1/12th of the span (D) 1/16th of the span

Last Answer : Answer: Option C

In a singly reinforced beam, the effective depth is measured from its compression edge to (A) Tensile edge (B) Tensile reinforcement (C) Neutral axis of the beam (D) Longitudinal central axis

Description : In a singly reinforced beam, the effective depth is measured from its compression edge to (A) Tensile edge (B) Tensile reinforcement (C) Neutral axis of the beam (D) Longitudinal central axis

Last Answer : Answer: Option B

Distribution reinforcement in a simply supported slab, is provided to distribute (A) Load (B) Temperature stress (C) Shrinkage stress (D) All the above

Description : Distribution reinforcement in a simply supported slab, is provided to distribute (A) Load (B) Temperature stress (C) Shrinkage stress (D) All the above

Last Answer : Answer: Option D

If diameter of a reinforcement bar is d, the anchorage value of the hook is (A) 4d (B) 8d (C) 12d (D) 16d

Description : If diameter of a reinforcement bar is d, the anchorage value of the hook is (A) 4d (B) 8d (C) 12d (D) 16d

Last Answer : Answer: Option D

The maximum area of tension reinforcement in beams shall not exceed (A) 0.15 % (B) 1.5 % (C) 4 % (D) 1 %

Description : The maximum area of tension reinforcement in beams shall not exceed (A) 0.15 % (B) 1.5 % (C) 4 % (D) 1 %

Last Answer : Answer: Option C

An R.C.C. beam not provided with shear reinforcement may develop cracks in its bottom inclined roughly to the horizontal at (A) 25° (B) 35° (C) 45° (D) 55°

Description : An R.C.C. beam not provided with shear reinforcement may develop cracks in its bottom inclined roughly to the horizontal at (A) 25° (B) 35° (C) 45° (D) 55°

Last Answer : Answer: Option C

The percentage of minimum reinforcement of the gross sectional area in slabs, is (A) 0.10 % (B) 0.12 % (C) 0.15 % (D) 0.18 %

Description : The percentage of minimum reinforcement of the gross sectional area in slabs, is (A) 0.10 % (B) 0.12 % (C) 0.15 % (D) 0.18 %

Last Answer : Answer: Option C

If the maximum shear stress at the end of a simply supported R.C.C. beam of 16 m effective span is 10 kg/cm2 , the length of the beam having nominal reinforcement, is (A) 8 cm (B) 6 m (C) 8 m (D) 10 m

Description : If the maximum shear stress at the end of a simply supported R.C.C. beam of 16 m effective span is 10 kg/cm2 , the length of the beam having nominal reinforcement, is (A) 8 cm (B) 6 m (C) 8 m (D) 10 m

Last Answer : Answer: Option C

In a beam the local bond stress Sb, is equal to (A) Shear force/(Leaver arm × Total perimeter of reinforcement) (B) Total perimeter of reinforcement/(Leaver arm × Shear force) (C) Leaver arm/(Shear force × Total perimeter of reinforcement) (D) Leaver arm/(Bending moment × Total perimeter of reinforcement)

Description : In a beam the local bond stress Sb, is equal to (A) Shear force/(Leaver arm Total perimeter of reinforcement) (B) Total perimeter of reinforcement/(Leaver arm Shear force) (C) ... force Total perimeter of reinforcement) (D) Leaver arm/(Bending moment Total perimeter of reinforcement)

Last Answer : Answer: Option A