Description : The laminated spring which is in common use, is of the type (a) full elliptic (b) semi elliptic (c)one quarter elliptic (d)three quarter elliptic
Last Answer : (b) semi elliptic
Description : ------------ are called cantilever laminated springs (a) Semi-elliptical springs (b) quarter elliptical springs (c) both (a) and (b) (d) none (Ans: b)
Last Answer : (b) quarter elliptical springs
Description : The longest leaf in Semi-elliptic leaf spring is known as (A) chief leaf (B) master leaf (C) major leaf (D) higher leaf
Last Answer : (B) master leaf
Description : The type of spring used to achieve greater load carrying capacity within given space is (a)spiral spring (b) springs in series (c)multi-leaf spring (d) concentric spring
Last Answer : (d) concentric spring
Description : In leaf springs the longest leaf is known as (a) Lower leaf (b) Master leaf (c) Upper leaf (d) None of these
Last Answer : (b) Master leaf
Description : Leaf springs absorb shocks by (a) bending (b) twisting (c) compression (d) tension
Last Answer : a) bending
Description : Leaf springs use (a) All full length leaves (b) All leaves of different lengths (c) Few full length leaves with truncated leaves (d) None
Last Answer : (c) Few full length leaves with truncated leaves
Description : Leaf springs are used in (a) Scooters (b) Bikes (c) Trucks (d) None
Last Answer : (c) Trucks
Description : Which type of springs have only active coils? a. Helical compression springs b. Helical tension springs c. Both a. and b. d. None of the above
Last Answer : b. Helical tension springs
Description : Laminated springs are used in (a) Watches (b) Sofas (c) Motorcycles (d) None
Last Answer : (d) None
Description : A concentric spring consists of 2 sprigs of diameter 10mm and 4mm. The net force acting on the composite spring is 5000N. Find the force acting on each of the two springs. (a) 1232.2N and 3767.8N (b) 786.4N and 4213.6N (c) 689.7N and 4310.3N (d) 645.3N and 4354.7N
Last Answer : (c) 689.7N and 4310.3N
Description : When two Belleville springs are in parallel, half force is obtained for a given deflection. (a) Half force (b) Double force (c) Same force (d) Can’t be determined
Last Answer : (b) Double force
Description : Coil springs absorb shocks by (a) bending (b) twisting (c) compression (d) tension
Last Answer : (c) compression
Description : The laminated springs are given initial curvature (a) To have uniform strength (b) To make it more economical (c) So that plates may become flat, when subjected to design load (d) None of these
Last Answer : (c) So that plates may become
Description : The springs in brakes and clutches are used (a) To apply forces (b) To measure forces (c) To absorb shocks (d) To absorb strain energy
Last Answer : (a) To apply forces
Description : eaf springs are designed on the basis of (a) Maximum bending stresses (b) Maximum deflection (c) Maximum bending as well as maximum deflection (d) None
Last Answer : (c) Maximum bending as well as maximum deflection
Description : Springs with rectangular or square cross section used for a. higher stiffness b. larger volume c. larger length d. smaller length
Last Answer : b. larger volume
Description : Two concentric springs with stiffness equal to 100 N/mm and 80 N/mm respectively, when subjected to load of 900N will deflect by a. 9mm b. 11.25 mm c. 5mm d. 31.5 mm
Last Answer : c. 5mm
Description : Music wires are concerned with a. musical instruments b. tuning forks c. springs d. measuring instruments
Last Answer : c. springs
Description : Coil springs absorb shocks by (A) bending (B) twisting (C) compression (D) tension
Last Answer : (C) compression
Description : Wahl’s stress concentration factor is used in close coiled springs under axial load to account for (a) Shear effect (b) Bending effect (c) Compression effect (d) none
Last Answer : (b) Bending effect
Description : When two helical springs of equal lengths are arranged to form a cluster spring, then a. Shear stress in each spring will be equal b. Load taken by each spring will be half the total load c. Only A is correct d. Both A and B is correct
Last Answer : d. Both A and B is correct
Description : A railway wagon moving with a speed of 1.5m/s is brought to rest by bumper consisting of two springs. Mass of wagon is 100kg. The springs are compressed by 125mm. Calculate the maximum force acting on each spring. a) 1200N b) 1500N c) 1800N d) 2000N
Last Answer : c) 1800N
Description : The shear stress concentration factor (Ks) in mechanical springs is given as _____ a. (1 + 0.5 / C) b. 0.615 / C c. (1 + 0.615 / C) d. [(4C – 1) / (4C + 1)] + [0.615 / C]
Last Answer : a. (1 + 0.5 / C)
Description : Solid length for helical compression springs having square and ground ends is given as _________. a. (n + 2)d b. (n + 3)d c. (n + 1)d d. None of the above
Last Answer : a. (n + 2)d
Description : Why are mechanical springs used? a. To apply force b. To store energy c. To measure force d. All of the above
Last Answer : d. All of the above
Description : Free length for helical compression springs having square ends is given as ________. a.pn + 2d b.pn + 3d c. 2(p + d) d.pn + 4d
Last Answer : b.pn + 3d
Description : Two close-coiled helical springs are equal in all respects except the number of turns. If the number of turns are in the ratio of 2:3, then the stiffness of the spring will be in the ratio of (a) 2:3 (b) 4:9 (c) 3:2 (d) 9:4
Last Answer : (c) 3:2
Description : A close –coiled helical spring is cut into two equal parts. The stiffness of the resulting springs will be (a) same (b) double (c) half (d) One-fourth
Last Answer : (b) double
Description : The close-coiled helical springs ‘A’ and ‘B’ are of same material, same coil diameter, same wire diameter and subjected to same load. If the number of turns of spring ‘A’ is half that of spring ‘B’, the ratio of deflection of spring ‘A’ to spring ‘B’ is (a)1/2 (b) 1 (c) 2 (d) 4
Last Answer : (a)1/2
Last Answer : (c) So that plates may become flat, when subjected to design load
Description : The region of the cross-section of a column in which compressive load may be applied without producing any tensile stress, is known as the core of the cross-section. In circular columns the radius of the core, ... One-third of the radius (c) One-quarter of the radius (d) One-fifth of the radius
Last Answer : (c) One-quarter of the radius
Description : In a simply supported beam carrying a uniformly distributed load over the left half span, the point of contraflexure will occur in (a) Left half span of the beam (b) Right half span of the beam. (c) Quarter points of the beam (d) Does not exist
Last Answer : (d) Does not exist
Description : With a leaf spring type of suspension, interference between steering and suspension system can be (a) front end of the spring is pin joined and the rear end is shackled (b) front end of the spring is ... joined (c) both end of the spring are shackled (d) both end of the spring are pin joined
Last Answer : (b) front end of the spring is shackled and the rear end is pin joined
Description : Among the cylindrical and spherical thin vessels of same material, diameter and pressure which has the lesser thickness a. Cylindrical shell b. Spherical shell c. Cylindrical shell with semi spherical heads d. None
Last Answer : b. Spherical shell
Description : Which of the following laminas have same moment of inertia (Ixx = Iyy), when passed through the centroid along x-x and y-y axes? a. Circle b. Semi-circle c. Right angle triangle d. Isosceles triangle
Last Answer : a. Circle
Description : Moment of inertia acting on a semi-circle about symmetrical axes is given as _______ a. 1.57 r4 b. 0.055 r4 c. 0.392 r4 d. 0.11 r4
Last Answer : c. 0.392 r4
Description : The clips placed at intervals along some leaf spring to prevent spring leaf separation on rebound are (a) rebound clips (b) separation clips (c) interval clips (d)relief clips
Last Answer : (a) rebound clips
Description : The device that permits variation in the distance between the spring eyes of a leaf spring as the spring flexes is called (a) Spring shackle (b) spring U bolt (c) spring hanger (d) spring leaf
Last Answer : (a) Spring shackle
Description : Leaf spring for vehicles are nipped to (a) To vary the effective length of the spring (b) to increase the interleaf friction (c) Improve the load carrying capacity of spring (d) ensure that all leaves are uniformly stressed during loading
Last Answer : (d) ensure that all leaves are uniformly stressed during loading
Description : A leaf spring consists of 3 extra full length leaves and 14 graduated length leaves. The maximum force that can act on the spring is 70kN and the distance between eyes of the spring is 1.2m. Width and thickness of the ... close the nip. (a) 4332.2N (b) 4674.1N (c) 4985.4N (d) Can't be determined
Last Answer : (b) 4674.1N
Description : A leaf spring consists of 3 extra full length leaves and 14 graduated length leaves. The maximum force that can act on the spring is 70kN and the distance between eyes of the spring is 1.2m. Width and thickness of the ... /mm², calculate the initial nip. (a) 26.8mm (b) 24.9mm (c) 22.5mm (d)23.1mm
Last Answer : b) 24.9mm
Description : The spring used in mechanical toys is (a) Leaf spring (b) Spiral spring (c) Helical spring (d) All of these
Last Answer : (b) Spiral spring
Description : A spring used to absorb shocks and vibrations is (a) Close-coil helical spring (b) Open coiled helical spring (c) Spiral spring (d) Leaf spring
Last Answer : (d) Leaf spring
Description : Strain energy in a leaf spring is (a) W x δ (b) W x δ/3 (c) W x δ/2 (d) None
Last Answer : (c) W x δ/2
Description : Overlap in a leaf spring is (a) L/n (b) L/2n (c) L/3n (d) None
Last Answer : (b) L/2n
Description : Maximum deflection in a leaf spring is given by (a) 3WL3/4Enbt3 (b) 3WL3/8Enbt3 (c) 3WL3/16Enbt3 (d) None
Last Answer : (b) 3WL3/8Enbt3
Description : Maximum bending stress in a leaf spring is (a) 3WL/4nbt2(b) 3WL/8nbt2(c) 3WL/2nbt2(d) None
Last Answer : (c) 3WL/2nbt2