Description : A close coiled spring under axial load produces (a) Bending stresses (b) Shear stresses (c) Tensile stresses (d) None
Last Answer : (b) Shear stresses
Description : When a close-coiled helical spring is subjected to an axial load, it is said to be under. (a) Bending (b) Shear (c) Torsion (d) Crushing
Last Answer : (c) Torsion
Description : A closed helical spring under axial load is designed on the basis of (a) Shear (b) Compression (c) Bending (d) None
Last Answer : (a) Shear
Description : Wahl suggested the correction in the stress factor to account for a. the additional transverse shear stress b. stress concentration c. fatigue stress d. axial stress
Last Answer : b. stress concentration
Description : A open helical spring under axial torque is designed on the basis of (a) Shear (b) Compression (c) Bending (d) None
Last Answer : d) None
Description : A closed helical spring under axial torque is designed on the basis of (a) Shear (b) Compression (c) Bending (d) None
Last Answer : (c) Bending
Description : The graphical representation of variation of axial load on y axis and position of cross section along x axis is called as _____ (a) Bending moment diagram (b) Shear force diagram (c) Stress-strain diagram (d) Trust diagram
Last Answer : (d) Trust diagram
Description : A close coiled helical spring is compressed. Its wire is subjected to A. Compression B. Tension C.Shear D. Torque
Last Answer : B. Tension
Description : The close-coiled helical springs ‘A’ and ‘B’ are of same material, same coil diameter, same wire diameter and subjected to same load. If the number of turns of spring ‘A’ is half that of spring ‘B’, the ratio of deflection of spring ‘A’ to spring ‘B’ is (a)1/2 (b) 1 (c) 2 (d) 4
Last Answer : (a)1/2
Description : Value of Wahl’s stress concentration factor is always (a) > 1 (b) = 1 (c) < 1 (d) None
Last Answer : (a) > 1
Description : Wahl’s stress concentration factor is (a) (4C – 1)/ (4C – 3) + 0.615/C (b) (4C – 1)/ (4C – 2) + 0.615/C (c) (4C – 1)/ (4C – 4) + 0.615/C (d) None
Last Answer : (c) (4C – 1)/ (4C – 4) + 0.615/C
Description : Wahl’s stress concentration factor is (a) [(4C—1)/(4C—4)] +0.615/C (b) [(4C—1)/(4C—4)] +0.625/C (c) [(4C—1)/(4C—4)] +0.635/C (d) None
Last Answer : a) [(4C—1)/(4C—4)] +0.615/C
Description : The shear stress concentration factor (Ks) in mechanical springs is given as _____ a. (1 + 0.5 / C) b. 0.615 / C c. (1 + 0.615 / C) d. [(4C – 1) / (4C + 1)] + [0.615 / C]
Last Answer : a. (1 + 0.5 / C)
Description : Shear stress in a close coiled helical spring is (a) 16WD/π d3 (b) 32WD/π d3 (c) 8WD/π d3 (d) None
Last Answer : (c) 8WD/π d3
Description : Two close-coiled helical springs are equal in all respects except the number of turns. If the number of turns are in the ratio of 2:3, then the stiffness of the spring will be in the ratio of (a) 2:3 (b) 4:9 (c) 3:2 (d) 9:4
Last Answer : (c) 3:2
Description : A close –coiled helical spring is cut into two equal parts. The stiffness of the resulting springs will be (a) same (b) double (c) half (d) One-fourth
Last Answer : (b) double
Description : The leaves of multi-leaf springs are subjected to (A) bending stress (B) shear stress (C) axial stress (D) all of the above
Last Answer : (A) bending stress
Description : When two helical springs of equal lengths are arranged to form a cluster spring, then a. Shear stress in each spring will be equal b. Load taken by each spring will be half the total load c. Only A is correct d. Both A and B is correct
Last Answer : d. Both A and B is correct
Description : Which factor is used to consider the effects of direct shear stress and torsional shear stress when curvature effect stress is not considered? a. Shear stress concentration factor b. Wahl shear stress concentration factor c. Both a. and b. d. None of the above
Last Answer : a. Shear stress concentration factor
Description : Coil springs absorb shocks by (a) bending (b) twisting (c) compression (d) tension
Last Answer : (c) compression
Description : Leaf springs absorb shocks by (a) bending (b) twisting (c) compression (d) tension
Last Answer : a) bending
Description : Coil springs absorb shocks by (A) bending (B) twisting (C) compression (D) tension
Last Answer : (C) compression
Description : Under sagging bending moment, the uppermost fiber of the beam is in (a) Shear (b) Compression (c) Tension (d) None)
Last Answer : (b) Compression
Description : Bending of beam occurs under (a) Axial load (b) Transverse load (c) Direct load (d) None
Last Answer : (b) Transverse load
Description : The type of stress induced in a closed coiled helical tension spring is a. tensile b. compressive c. torsional shear d. tensile and compressive
Last Answer : c. torsional shear
Description : When a column is subjected to an eccentric load, the stress induced in the column will be (a) direct stress only (b) bending stress only (c) shear stress only (d) direct and bending stress both
Last Answer : (d) direct and bending stress both
Description : When the helical compression spring is subjected to axial compressive force, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress
Last Answer : (D) Torsional shear stress
Description : Find the shear stress in the spring wire used to design a helical compression sprig if a load of 1200N is applied on the spring. Spring index is 6, and wire diameter 7mm. a) 452.2N/mm² b) 468.6N/mm² c) 512.2N/mm² d) None of the listed
Last Answer : b) 468.6N/mm²
Description : Wahl factor to account for direct shear stress and stress concentration due to curvature for helical springs is given by, (A) (4C - 1/4C - 4) + 0.615/C (B) (4C - 1/4C + 4) + 0.615/C (C) (4C + 1/4C - 4) + 0.615/C (D) (4C + 1/4C + 4) + 0.615/C
Last Answer : (A) (4C - 1/4C - 4) + 0.615/C
Description : A carriage spring is designed on the basis of (a) Shear (b) Compression (c) Bending (d) None
Description : Equivalent bending moment in a shaft subjected to axial load P, torque T and bending moment M is (a) Meq = 0.5 [M + (M2 + T2)0.5]0.5 (b) Meq = 0.5 [M + (M2 + T2)0.5] (c) Meq = ( M2 + T2)0.5 (d) None
Last Answer : (b) Meq = 0.5 [M + (M2 + T2)0.5]
Description : Equivalent torque in a shaft subjected to axial load P, torque T and bending moment M is (a) Teq = (Pa2 + M2 + T2) (b) Teq = (Pa2 + M2 + T2)0.5 (c)Teq = ( M2 + T2)0.5 (d) None
Last Answer : c)Teq = ( M2 + T2)0.5
Description : A beam is a structural member which is subjected to (a) Axial tension or compression (b) Transverse loads and couples (c) Twisting moment (d) No load, but its axis should be horizontal and x-section rectangular or circular
Last Answer : b) Transverse loads and couples
Description : A diagram which shows the variations of the axial load for all sections of the span of a beam, is called (A) Bending moment diagram (B) Shear force diagram (C) Thrust diagram (D) Stress diagram
Last Answer : Answer: Option C
Description : Find the Wahl’s factor if spring index is 6. a) 1.2020 b) 1.2424 c) 1.2525 d) 1.5252
Last Answer : c) 1.2525
Description : What is the Wahl's factor if spring index is 6? a. 1.477 b. 0.995 c. 1.252 d. None of the above
Last Answer : c. 1.252
Description : A transmission shaft subjected to bending loads must be designed on the basis of (a) maximum normal stress theory (b) maximum shear stress theory (c) maximum normal stress and maximum shear stress theories (d) fatigue strength
Last Answer : (a) maximum normal stress theory
Description : Torque and bending moment of 100 kN.m and 200 kN.m acts on a shaft which has external diameter twice of internal diameter. What is the external diameter of the shaft which is subjected to a maximum shear stress of 90 N/mm2? a. 116.5 mm b. 233.025 mm c. 587.1 mm d. 900 mm
Last Answer : c. 587.1 mm
Description : What is the maximum shear stress induced in a solid shaft of 50 mm diameter which is subjected to both bending moment and torque of 300 kN.mm and 200 kN.mm respectively? a. 9.11 N/mm2 b. 14.69 N/mm2 c. 16.22 N/mm2 d. 20.98 N/mm2
Last Answer : b. 14.69 N/mm2
Description : The ratio of maximum bending stress to maximum shear stress on the cross section when a shaft is simultaneously subjected to a torque T and bending moment M, a. T/M b. M/T c. 2T/M d. 2M/T
Last Answer : d. 2M/T
Description : A beam of uniform strength has a. same cross-section throughout the beam b. same bending stress at every section c. same bending moment at every section d. same shear stress at every section
Last Answer : b. same bending stress at every section
Description : In a cantilever subjected to a combination of concentrated load, uniformly distributed load and uniformly varying load, Maximum bending moment is (a) Where shear force=0 (b) At the free end (c) At the fixed end (d) At the mid-point
Last Answer : (c) At the fixed end
Description : There are number of laminations in a (a) Close coiled spring (b) Open coiled spring (c) Spiral spring (d) None
Last Answer : (d) None
Description : A spring used to absorb shocks and vibrations is (a) Close-coil helical spring (b) Open coiled helical spring (c) Spiral spring (d) Leaf spring
Last Answer : (d) Leaf spring
Description : Strain energy in a close coiled helical spring is (a) τ2/8G (b) τ2/16G (c) τ2/4G (d) None
Last Answer : (c) τ2/4G
Description : Deflection in a close coiled helical spring is (a) 16 WR3n/Gd4 (b) 32 WR3n/Gd4 (c) 64 WR3n/Gd4 (d) None
Last Answer : (c) 64 WR3n/Gd4
Description : Angle of helix in a close coiled spring is (a) < 100 (b) >100 (c) =100 (d) None
Last Answer : (a) < 100
Description : If a close-coiled helical spring absorbs 50 N-mm of energy while extending by 5 mm, its stiffness will be (a) 2 N/mm (b) 4 N/mm (c) 6 N/mm (d) 10 N/mm
Last Answer : (d) 10 N/mm
Description : A close-coiled helical spring of stiffness 30 N/mm is arranged in series with another such spring of stiffness 60 N/mm. The stiffness of composite unit is (a) 20 N/mm (b) 30 N/mm (c) 45 N/mm (d) 90 N/mm
Last Answer : (a) 20 N/mm