What is the purpose of starting resistors?

What is the purpose of starting resistors?
by

1 Answer

Answer :

To limit armature current until counter emf builds up
by

Related questions

A resistor is handed to you for identification with the following color code: the first band is blue, followed by gray, green, gold, and brown. What is the resistor’s value?

Description : A resistor is handed to you for identification with the following color code: the first band is blue, followed by gray, green, gold, and brown. What is the resistor’s value?

Last Answer : 6,800,000 ohms (6.8 mega ohms), with 5% tolerance, and a 1% reliability level.

What are the two disadvantages of carbon-type resistors?

Description : What are the two disadvantages of carbon-type resistors?

Last Answer : 1. Change value with age. 2. Limited power capacity.

Refer to figure 3-55(A). If the following resistors were replaced with the values indicated: R1 = 900Ω, R3 = 1kΩ, what is the total power in the circuit? What is ER2?

Description : Refer to figure 3-55(A). If the following resistors were replaced with the values indicated: R1 = 900Ω, R3 = 1kΩ, what is the total power in the circuit? What is ER2?

Last Answer : PT = 60 W, ER2 = 10 V.

Three resistors connected in parallel have values of 12 kΩ, 20kΩ, and 30kΩ. What is the equivalent resistance? A37. 6kΩ Q38. Two resistors connected in parallel have values of 10 kΩ and 30kΩ. What is eht equivalent resistance?

Description : Three resistors connected in parallel have values of 12 kΩ, 20kΩ, and 30kΩ. What is the equivalent resistance? A37. 6kΩ Q38. Two resistors connected in parallel have values of 10 kΩ and 30kΩ. What is eht equivalent resistance?

Last Answer : 7.5kΩ

Four equal resistors are connected in parallel, each resistor has an ohmic value of 100 ohms, what is the equivalent resistance?

Description : Four equal resistors are connected in parallel, each resistor has an ohmic value of 100 ohms, what is the equivalent resistance?

Last Answer : 25 ohms

A series circuit consists of two resistors in series. R1 = 25 ohms and R2 = 30 ohms. The circuit current is 6 amps. What is the (a) source voltage, (b) voltage dropped by each resistor, (c) total power, and (d) power used by each resistor?

Description : A series circuit consists of two resistors in series. R1 = 25 ohms and R2 = 30 ohms. The circuit current is 6 amps. What is the (a) source voltage, (b) voltage dropped by each resistor, (c) total power, and (d) power used by each resistor?

Last Answer : (a) 330 volts. (b) E1 = 150 volts. E2 = 180 volts. (c) 1.98 kilowatts. (d) P1 = 900 watts. P2 = 1.08 kilowatts component but in a parallel circuit total current divides among the available paths.

A circuit has a source voltage of 100 volts and two 50-ohm resistors connected in series. If the reference point for this circuit is placed between the two resistors, what would be the voltage at the reference point?

Description : A circuit has a source voltage of 100 volts and two 50-ohm resistors connected in series. If the reference point for this circuit is placed between the two resistors, what would be the voltage at the reference point?

Last Answer : 50 volts.

A series circuit consisting of three resistors has a current of 3 amps. If R1 = 20 ohms, R2= 60 ohms, and R 3 = 80 ohms, what is the (a) total resistance and (b) source voltage of the circuit?

Description : A series circuit consisting of three resistors has a current of 3 amps. If R1 = 20 ohms, R2= 60 ohms, and R 3 = 80 ohms, what is the (a) total resistance and (b) source voltage of the circuit?

Last Answer : (a) 160 ohms. (b) 480 ohms

When using Kirchhoff’s voltage law, how are voltage polarities assigned to the voltage drops across resistors? When using Kirchhoff’s voltage law, how are voltage polarities assigned to the voltage drops across resistors?

Description : When using Kirchhoff’s voltage law, how are voltage polarities assigned to the voltage drops across resistors?

Last Answer : The point at which current enters the resistor is assigned a negative polarity and the point at which current leaves the resistor is

The purpose of the 'heater resistors' for the winch circuit shown in the illustration is to _______________. EL-0102 A. limit the current in the heater circuit B. dispel moisture in the 'master switch' housing & control panel C. keep the winch brake housing below the dew point D. maintain winch motor operating temperature

Description : The purpose of the 'heater resistors' for the winch circuit shown in the illustration is to _______________. EL-0102 A. limit the current in the heater circuit B. dispel moisture in the ' ... panel C. keep the winch brake housing below the dew point D. maintain winch motor operating temperature

Last Answer : Answer: B

What is the purpose of connecting external resistors to slip ring Induction motor?

Description : What is the purpose of connecting external resistors to slip ring Induction motor?

Last Answer : It increases starting torque and decreases starting current.

The colour band on the extreme left in general purpose fixed resistors represents:

Description : The colour band on the extreme left in general purpose fixed resistors represents: A) Tolerance B) First significant digit C) Wattage Rating D) Voltage Rating

Last Answer : The colour band on the extreme left in general purpose fixed resistors represents: First significant digit

How do split-phase induction motors become self-starting?

Description : How do split-phase induction motors become self-starting?

Last Answer : By using combinations of inductance and capacitance to apply out-of phase currents in starting windings.

Electronics question: Do resistors work both ways?

Description : Electronics question: Do resistors work both ways?

Last Answer : Yes, resistors work both ways. The gold/yellow stripe only is relevate to the tolerance.

How many types of resistors ?

Description : How many types of resistors ?

Last Answer : 2 types of resistors .

What is the potential difference between the resistors in the classification ?

Description : What is the potential difference between the resistors in the classification ?

Last Answer : The potential difference of the resistors is not equal

The parkside PAS 7.2 A1 cordless screwdriver burned two resistors next to the Cˇ, C- inlet. Does anyone have the opportunity to read the values ​​on these resistors?

Description : For the parkside PAS 7.2 A1 cordless screwdriver, two resistors burned next to the C +, C- supply. Does anyone have the opportunity to read the values ​​on these resistors?

Last Answer : If the colors can be recognized, try the page with the possibility of entering the detected colors: Color marking of resistors, code marking of capacitors

How to find the potential difference across a battery in a series parallel circuit with resistors that have no value given?

Description : How to find the potential difference across a battery in a series parallel circuit with resistors that have no value given?

Last Answer : The potential difference is obtthe difference of all voltage across a terminal. From the circuit above I think the resistors are in series and parallel to each other. The two resistors in line CB are ... place the multimeter in series with the circuit and you will get the resistance. But ise you

Calculate the equivalent resistance between points A and B in each of the following networks of resistors :

Description : Calculate the equivalent resistance between points A and B in each of the following networks of resistors :

Last Answer : Calculate the equivalent resistance between points A and B in each of the following networks of resistors :

A `5 Omega` resistor is connected in series with a parallel combination of n resistors of `6 Omega` each. The equivalent resistance is `7 Omega`. Find

Description : A `5 Omega` resistor is connected in series with a parallel combination of n resistors of `6 Omega` each. The equivalent resistance is `7 Omega`. Find

Last Answer : A `5 Omega` resistor is connected in series with a parallel combination of n resistors of `6 Omega ... The equivalent resistance is `7 Omega`. Find n.

(i) Three resistors `2 Omega, 4 Omega " and " 5 Omega` are comined in parallel. What is the total resistance of the combination ? (ii) If the comnbina

Description : (i) Three resistors `2 Omega, 4 Omega " and " 5 Omega` are comined in parallel. What is the total resistance of the combination ? (ii) If the comnbina

Last Answer : (i) Three resistors `2 Omega, 4 Omega " and " 5 Omega` are comined in parallel. What ... current through each resistor, and the total current drawn.

Three resistors of `1 Omega, 2 Omega " and " 3 Omega` are combined in series. (i) What is the total resistance of the combination ? (ii) If the combin

Description : Three resistors of `1 Omega, 2 Omega " and " 3 Omega` are combined in series. (i) What is the total resistance of the combination ? (ii) If the combin

Last Answer : Three resistors of `1 Omega, 2 Omega " and " 3 Omega` are combined in series. ( ... resistance, obtain the potential dropo across each resistor.

`6Omega` and `12Omega` resistors are connected in parallel. This combination is connected in series with 10 V battery and `6 Omega` resistor. What is

Description : `6Omega` and `12Omega` resistors are connected in parallel. This combination is connected in series with 10 V battery and `6 Omega` resistor. What is

Last Answer : `6Omega` and `12Omega` resistors are connected in parallel. This combination is connected in series with 10 V battery and ... 4 V B. 16 V C. 2 D. 8 V

Two resistors of `6 Omega " and " 9 Omega` are connected in series to a 120 V source. The power consumed by the `6 Omega` resistor is

Description : Two resistors of `6 Omega " and " 9 Omega` are connected in series to a 120 V source. The power consumed by the `6 Omega` resistor is

Last Answer : Two resistors of `6 Omega " and " 9 Omega` are connected in series to a 120 V source. The power consumed by ... 384 W B. 616 W C. 1500 W D. 1800 W

Two resistors of resistances `2Omega` and `6Omega` are connected in parallel. This combination is then connected to a battery of emf 2 V and internal

Description : Two resistors of resistances `2Omega` and `6Omega` are connected in parallel. This combination is then connected to a battery of emf 2 V and internal

Last Answer : Two resistors of resistances `2Omega` and `6Omega` are connected in parallel. This combination is then connected to a ... . `(4)/(17)A` D. `1 A`

In the network of resistors shown in the adjoining figure, the equivalent resistance between A and B is

Description : In the network of resistors shown in the adjoining figure, the equivalent resistance between A and B is

Last Answer : In the network of resistors shown in the adjoining figure, the equivalent resistance between A and B is A. 54 ... `Omega` C. 36 `Omega` D. 9 `Omega`

Two resistors `400Omega` and `800Omega` are connected in series with a `6V` battery. It is desired to measure the current in the circuit. An ammeter o

Description : Two resistors `400Omega` and `800Omega` are connected in series with a `6V` battery. It is desired to measure the current in the circuit. An ammeter o

Last Answer : Two resistors `400Omega` and `800Omega` are connected in series with a `6V` battery. It is desired to measure the current ... .95` V C. `3.8` V D. 4 V

Three resistors each of 2 ohm are connected together in a triangular shape. The resistance between any two vertices will be

Description : Three resistors each of 2 ohm are connected together in a triangular shape. The resistance between any two vertices will be

Last Answer : Three resistors each of 2 ohm are connected together in a triangular shape. The resistance between any two ... 3//4Omega` C. `3Omega` D. `6Omega`

A student has 10 resistors of resistance ‘ r ’. The minimum resistance made by him from given resistors is

Description : A student has 10 resistors of resistance ‘ r ’. The minimum resistance made by him from given resistors is

Last Answer : A student has 10 resistors of resistance r '. The minimum resistance made by him from given resistors is A. 10r B. ` ... C. `(r)/(100)` D. `(r)/(5)`

What must be the same for two resistors that are connected in a parallel?

Description : What must be the same for two resistors that are connected in a parallel?

Last Answer : It is not necessary for anything about them to be the same.All that is necessary is that they create the desired equivalent resistor, having the correct resistance and power dissipation rating without overstressing either resistor.

What picture represents two resistors wired in parallel?

Description : What picture represents two resistors wired in parallel?

Last Answer : It represents that two resistors are connected in parallel.

Why are devices run by electrical energy represented as resistors in a circuit?

Description : Why are devices run by electrical energy represented as resistors in a circuit?

Last Answer : A resistor in a circuit impedes the flow of electrons and drawsenergy from the circuit. That is what an electric device is, and ona circuit diagram the zig-zag line is clean and ... circuit. Insuch cases the representation would have to include inductorsand/or capacitors as well as resistors.

A battery is connected to a circuit containing three resistors in parallel. The values of the three resistors are 2 ohms, 3 ohms, and 6 ohms. What is the voltage of the battery if the total circuit current is 12 amps? A. 2 volts B. 6 volts C. 12 volts D. 24 volt

Description : A battery is connected to a circuit containing three resistors in parallel. The values of the three resistors are 2 ohms, 3 ohms, and 6 ohms. What is the voltage of the battery if the total circuit current is 12 amps? A. 2 volts B. 6 volts C. 12 volts D. 24 volt

Last Answer : Answer: C

A fuse will 'blow' if _____________. A. an electric motor is stopped suddenly by opening a switch B. the flow of current to the protection device is reversed C. the electrical current exceeds the rated value of the fuse D. unequal resistors are connected in parallel

Description : A fuse will 'blow' if _____________. A. an electric motor is stopped suddenly by opening a switch B. the flow of current to the protection device is reversed C. the electrical current exceeds the rated value of the fuse D. unequal resistors are connected in parallel

Last Answer : Answer: C

Peripheral components for the operation of the astern valve position amplifier circuit shown in the illustration are _____________. EL-0099 A. resistors B. operated on +28 volts D.C. C. located on a separate circuit card D. all of the above

Description : Peripheral components for the operation of the astern valve position amplifier circuit shown in the illustration are _____________. EL-0099 A. resistors B. operated on +28 volts D.C. C. located on a separate circuit card D. all of the above

Last Answer : Answer: C

When troubleshooting a console circuit card which is suspected of being faulty, the first step would be to _____. A. pull the card and measure the value of all resistors B. check for the correct value and polarity of all power connections to the card C. de-energize and pull the card to visually inspect for burned components D. check for continuity of circuit board traces and then the gain of each transistor

Description : When troubleshooting a console circuit card which is suspected of being faulty, the first step would be to _____. A. pull the card and measure the value of all resistors B. check for the ... for burned components D. check for continuity of circuit board traces and then the gain of each transistor

Last Answer : Answer: C

What power would be consumed in EACH of the branch resistors of the circuit shown in the illustration if the source is 30 volts, the resistance for R1 is 10 ohms, R2 is 10 ohms and R3 is 10 ohms? EL-0032 A. 5 watts B. 10 watts C. 20 watts D. 40 watts

Description : What power would be consumed in EACH of the branch resistors of the circuit shown in the illustration if the source is 30 volts, the resistance for R1 is 10 ohms, R2 is 10 ohms and R3 is 10 ohms? EL-0032 A. 5 watts B. 10 watts C. 20 watts D. 40 watts

Last Answer : Answer: B

An ammeter reads slightly above 'zero' when its leads are disconnected, this is a result of ___________. A. mechanical misalignment of the meter pointer B. a poor ground for the meter case C. static electricity in the air D. resistors inside the meter storing charges

Description : An ammeter reads slightly above 'zero' when its leads are disconnected, this is a result of ___________. A. mechanical misalignment of the meter pointer B. a poor ground for the meter case C. static electricity in the air D. resistors inside the meter storing charges

Last Answer : Answer: A

The total voltage of a series circuit is the _____________. A. sum of the individual voltage drops B. total resistance divided by the total current C. sum of the individual currents multiplied by the number of resistors D. total current divided by the total resistance

Description : The total voltage of a series circuit is the _____________. A. sum of the individual voltage drops B. total resistance divided by the total current C. sum of the individual currents multiplied by the number of resistors D. total current divided by the total resistance

Last Answer : Answer: A

A solid-state circuit is inoperative; the FIRST action that should be taken is to ____________. A. wiggle all the components to check for loose connections B. check all the resistors C. change all transistors D. check the DC supply voltage

Description : A solid-state circuit is inoperative; the FIRST action that should be taken is to ____________. A. wiggle all the components to check for loose connections B. check all the resistors C. change all transistors D. check the DC supply voltage

Last Answer : Answer: D

In an induction motor, rotor currents are circulated in the rotor by _____________. A. slip rings and brushes B. an armature and brushes C. inductive reaction of the rotating stator field D. external variable resistors

Description : In an induction motor, rotor currents are circulated in the rotor by _____________. A. slip rings and brushes B. an armature and brushes C. inductive reaction of the rotating stator field D. external variable resistors

Last Answer : Answer: C

One of the following is a possible cause for a slow drift of frequency in a self-exited transmitter oscillator circuits resulting to a poor frequency stability. A. Loose shielding B. Heating of capacitor in the oscillator C. Poor soldered connections D. Faulty capacitor, resistor, tubes or resistors

Description : One of the following is a possible cause for a slow drift of frequency in a self-exited transmitter oscillator circuits resulting to a poor frequency stability. A. Loose shielding B. ... capacitor in the oscillator C. Poor soldered connections D. Faulty capacitor, resistor, tubes or resistors

Last Answer : B. Heating of capacitor in the oscillator

One of the following is a possible cause of an abrupt frequency variation in a self exited transmitter oscillator circuits resulting to a poor frequency stability to hold a constant frequency oscillation. A. Heating and expansion of oscillator coil B. DC and RF ac heating of resistors which cause change in values C. Heating of capacitor in the oscillatorD. Loose connections in the oscillator, amplifier, or antenna circuits.

Description : One of the following is a possible cause of an abrupt frequency variation in a self exited transmitter oscillator circuits resulting to a poor frequency stability to hold a constant frequency ... capacitor in the oscillator D. Loose connections in the oscillator, amplifier, or antenna circuits.

Last Answer : D. Loose connections in the oscillator, amplifier, or antenna circuits.

Which of the following is one of the possible causes for a slow drift of frequency in a self exited transmitter oscillator circuits resulting to a poor frequency stability? A. Poor soldered connections B. Power supply voltage changes C. Loose connections in the oscillator, amplifier, or antenna circuits D. DC and RF heating of resistors, causing then to change values.

Description : Which of the following is one of the possible causes for a slow drift of frequency in a self exited transmitter oscillator circuits resulting to a poor frequency stability? A. Poor soldered connections ... , or antenna circuits D. DC and RF heating of resistors, causing then to change values.

Last Answer : D. DC and RF heating of resistors, causing then to change values.

Two resistors, 20kΩ, and 50kΩ are at ambient temperature. Calculate for a bandwidth equal to 100kHz, the thermal noise voltage for the two resistors connected in parallel. A. 0.4782µV B. 4278 µV C. 4.78 µV D. 47.8 µV

Description : Two resistors, 20kΩ, and 50kΩ are at ambient temperature. Calculate for a bandwidth equal to 100kHz, the thermal noise voltage for the two resistors connected in parallel. A. 0.4782µV B. 4278 µV C. 4.78 µV D. 47.8 µV

Last Answer : C. 4.78 µV

Two 10 Ω resistors are connected in parallel, their equivalent resistance is A. 5 ΩB. 0.2 ΩC. 15 ΩD. 20 Ω

Description : Two 10 Ω resistors are connected in parallel, their equivalent resistance isA. 5 Ω B. 0.2 Ω C. 15 Ω D. 20 Ω

Last Answer :  5 Ω

To reduce short circuit fault currents are used. (a) reactors (b) resistors (c) capacitors (d) none of the above

Description : To reduce short circuit fault currents are used. (a) reactors (b) resistors (c) capacitors (d) none of the above

Last Answer : (a) reactors

What is colour code of resistors , Please explain ?

Description : What is colour code of resistors , Please explain ?

Last Answer : Colours to denote value. In four band colour coding, the first band indicates the first digit, the second band : the second digit and the third band : the number of zeroes.