What are the two disadvantages of carbon-type resistors?

What are the two disadvantages of carbon-type resistors?
by

1 Answer

Answer :

1. Change value with age. 2. Limited power capacity.
by

Related questions

What type resistor should be used to overcome the disadvantages of the carbon resistor?

Description : What type resistor should be used to overcome the disadvantages of the carbon resistor?

Last Answer : The wirewound resistor.

Three resistors connected in parallel have values of 12 kΩ, 20kΩ, and 30kΩ. What is the equivalent resistance? A37. 6kΩ Q38. Two resistors connected in parallel have values of 10 kΩ and 30kΩ. What is eht equivalent resistance?

Description : Three resistors connected in parallel have values of 12 kΩ, 20kΩ, and 30kΩ. What is the equivalent resistance? A37. 6kΩ Q38. Two resistors connected in parallel have values of 10 kΩ and 30kΩ. What is eht equivalent resistance?

Last Answer : 7.5kΩ

A series circuit consists of two resistors in series. R1 = 25 ohms and R2 = 30 ohms. The circuit current is 6 amps. What is the (a) source voltage, (b) voltage dropped by each resistor, (c) total power, and (d) power used by each resistor?

Description : A series circuit consists of two resistors in series. R1 = 25 ohms and R2 = 30 ohms. The circuit current is 6 amps. What is the (a) source voltage, (b) voltage dropped by each resistor, (c) total power, and (d) power used by each resistor?

Last Answer : (a) 330 volts. (b) E1 = 150 volts. E2 = 180 volts. (c) 1.98 kilowatts. (d) P1 = 900 watts. P2 = 1.08 kilowatts component but in a parallel circuit total current divides among the available paths.

A circuit has a source voltage of 100 volts and two 50-ohm resistors connected in series. If the reference point for this circuit is placed between the two resistors, what would be the voltage at the reference point?

Description : A circuit has a source voltage of 100 volts and two 50-ohm resistors connected in series. If the reference point for this circuit is placed between the two resistors, what would be the voltage at the reference point?

Last Answer : 50 volts.

A resistor is handed to you for identification with the following color code: the first band is blue, followed by gray, green, gold, and brown. What is the resistor’s value?

Description : A resistor is handed to you for identification with the following color code: the first band is blue, followed by gray, green, gold, and brown. What is the resistor’s value?

Last Answer : 6,800,000 ohms (6.8 mega ohms), with 5% tolerance, and a 1% reliability level.

What is the purpose of starting resistors?

Description : What is the purpose of starting resistors?

Last Answer : To limit armature current until counter emf builds up

Refer to figure 3-55(A). If the following resistors were replaced with the values indicated: R1 = 900Ω, R3 = 1kΩ, what is the total power in the circuit? What is ER2?

Description : Refer to figure 3-55(A). If the following resistors were replaced with the values indicated: R1 = 900Ω, R3 = 1kΩ, what is the total power in the circuit? What is ER2?

Last Answer : PT = 60 W, ER2 = 10 V.

Four equal resistors are connected in parallel, each resistor has an ohmic value of 100 ohms, what is the equivalent resistance?

Description : Four equal resistors are connected in parallel, each resistor has an ohmic value of 100 ohms, what is the equivalent resistance?

Last Answer : 25 ohms

A series circuit consisting of three resistors has a current of 3 amps. If R1 = 20 ohms, R2= 60 ohms, and R 3 = 80 ohms, what is the (a) total resistance and (b) source voltage of the circuit?

Description : A series circuit consisting of three resistors has a current of 3 amps. If R1 = 20 ohms, R2= 60 ohms, and R 3 = 80 ohms, what is the (a) total resistance and (b) source voltage of the circuit?

Last Answer : (a) 160 ohms. (b) 480 ohms

When using Kirchhoff’s voltage law, how are voltage polarities assigned to the voltage drops across resistors? When using Kirchhoff’s voltage law, how are voltage polarities assigned to the voltage drops across resistors?

Description : When using Kirchhoff’s voltage law, how are voltage polarities assigned to the voltage drops across resistors?

Last Answer : The point at which current enters the resistor is assigned a negative polarity and the point at which current leaves the resistor is

State any two features of carbon composition resistors.

Description : State any two features of carbon composition resistors.

Last Answer : Features of Carbon composition resistance: i) Low cost ii) Wide resistance range ( ohm to mega ohm) iii) Wide range of working voltage iv) Simple in construction 

Carbon resistors are used extensively because they are?

Last Answer : Carbon resistors are used extensively because they are easy to make, compact, inexpensive.

What are the two main disadvantages of an LC capacitor filter?

Description : What are the two main disadvantages of an LC capacitor filter?

Last Answer : Cost and size of the inductor.

What are two disadvantages of procedure oriented languages?

Description : What are two disadvantages of procedure oriented languages?

Last Answer : They require more space in memory and they process data at a slower rate than symbolic languages.

. What are the two main disadvantages of an LC capacitor filter?

Description : . What are the two main disadvantages of an LC capacitor filter?

Last Answer : Cost of the inductor and size of the inductor.

What are the two primary disadvantages of a two-wire open line?

Description : What are the two primary disadvantages of a two-wire open line?

Last Answer : High radiation losses and noise pickup.

There are two types of tape transport configurations, open loop capstan drive and closed-loop capstan drive. What are two major disadvantages of open-loop capstan drive tape transports?

Description : There are two types of tape transport configurations, open loop capstan drive and closed-loop capstan drive. What are two major disadvantages of open-loop capstan drive tape transports?

Last Answer : a. Only operates in one direction. b. The tape tension and head-to-tape contact can vary.

What are two disadvantages of the take-up control reeling system?

Description : What are two disadvantages of the take-up control reeling system?

Last Answer : a. It only works in one direction. b. The tape tension varies as the supply reel unwinds, which can cause damage during starts and stops.

What are two disadvantages of using a recorder’s erase head to erase data recorded on a magnetic tape?

Description : What are two disadvantages of using a recorder’s erase head to erase data recorded on a magnetic tape?

Last Answer : Using an erase head is slow, and it may not completely erase the tape.

Name two major disadvantages of transistors.

Description : Name two major disadvantages of transistors.

Last Answer : Sensitive to heat and minor overloads.

What are the primary disadvantages of the magic-T?

Description : What are the primary disadvantages of the magic-T?

Last Answer : Low power-handling capability and power losses

What are some disadvantages of operating a transmitter at or near the muf?

Description : What are some disadvantages of operating a transmitter at or near the muf?

Last Answer : Frequent signal fading and dropouts.

What are some disadvantages of operating transmitters at or near the luf?

Description : What are some disadvantages of operating transmitters at or near the luf?

Last Answer : Signal-to-noise ratio is low and the probability of multipath propagation is greater.

List the three disadvantages of the air coaxial line

Description : List the three disadvantages of the air coaxial line

Last Answer : Expensive to construct, must be kept dry, and high frequency losses limit the practical length of the line.

What is one of the major disadvantages of multilayer printed circuit boards?

Description : What is one of the major disadvantages of multilayer printed circuit boards?

Last Answer : Difficulty of repair of internal connections.

What are the disadvantages of point-to-point wiring?

Description : What are the disadvantages of point-to-point wiring?

Last Answer : "Rat's nest" appearance and unwanted interaction, such as capacitive and inductive effects.

How do closed-loop capstan drive tape transports overcome the disadvantages of the open-loop drive design?

Description : How do closed-loop capstan drive tape transports overcome the disadvantages of the open-loop drive design?

Last Answer : Closed loop capstan drive transports use more than one capstan to clamp the tape in the area around the magnetic head.

What are the disadvantages of radiotelephone communications?

Description : What are the disadvantages of radiotelephone communications?

Last Answer : Static, enemy interference or a high local noise level.

What are the disadvantages of the parasitic array?

Description : What are the disadvantages of the parasitic array?

Last Answer : Their adjustment is critical and they do not operate over a wide frequency range.

What are some disadvantages of the end-fire array?

Description : What are some disadvantages of the end-fire array?

Last Answer : Extremely low radiation resistance, confined to one frequency, and affected by atmospheric conditions.

Some wire- wound resistors have bifilar winding. This type of winding is used to

Last Answer : Some wire- wound resistors have bifilar winding. This type of winding is used to Reduce the inductance of winding.

The parkside PAS 7.2 A1 cordless screwdriver burned two resistors next to the Cˇ, C- inlet. Does anyone have the opportunity to read the values ​​on these resistors?

Description : For the parkside PAS 7.2 A1 cordless screwdriver, two resistors burned next to the C +, C- supply. Does anyone have the opportunity to read the values ​​on these resistors?

Last Answer : If the colors can be recognized, try the page with the possibility of entering the detected colors: Color marking of resistors, code marking of capacitors

Two resistors of `6 Omega " and " 9 Omega` are connected in series to a 120 V source. The power consumed by the `6 Omega` resistor is

Description : Two resistors of `6 Omega " and " 9 Omega` are connected in series to a 120 V source. The power consumed by the `6 Omega` resistor is

Last Answer : Two resistors of `6 Omega " and " 9 Omega` are connected in series to a 120 V source. The power consumed by ... 384 W B. 616 W C. 1500 W D. 1800 W

Two resistors of resistances `2Omega` and `6Omega` are connected in parallel. This combination is then connected to a battery of emf 2 V and internal

Description : Two resistors of resistances `2Omega` and `6Omega` are connected in parallel. This combination is then connected to a battery of emf 2 V and internal

Last Answer : Two resistors of resistances `2Omega` and `6Omega` are connected in parallel. This combination is then connected to a ... . `(4)/(17)A` D. `1 A`

Two resistors `400Omega` and `800Omega` are connected in series with a `6V` battery. It is desired to measure the current in the circuit. An ammeter o

Description : Two resistors `400Omega` and `800Omega` are connected in series with a `6V` battery. It is desired to measure the current in the circuit. An ammeter o

Last Answer : Two resistors `400Omega` and `800Omega` are connected in series with a `6V` battery. It is desired to measure the current ... .95` V C. `3.8` V D. 4 V

Three resistors each of 2 ohm are connected together in a triangular shape. The resistance between any two vertices will be

Description : Three resistors each of 2 ohm are connected together in a triangular shape. The resistance between any two vertices will be

Last Answer : Three resistors each of 2 ohm are connected together in a triangular shape. The resistance between any two ... 3//4Omega` C. `3Omega` D. `6Omega`

What must be the same for two resistors that are connected in a parallel?

Description : What must be the same for two resistors that are connected in a parallel?

Last Answer : It is not necessary for anything about them to be the same.All that is necessary is that they create the desired equivalent resistor, having the correct resistance and power dissipation rating without overstressing either resistor.

What picture represents two resistors wired in parallel?

Description : What picture represents two resistors wired in parallel?

Last Answer : It represents that two resistors are connected in parallel.

Two resistors, 20kΩ, and 50kΩ are at ambient temperature. Calculate for a bandwidth equal to 100kHz, the thermal noise voltage for the two resistors connected in parallel. A. 0.4782µV B. 4278 µV C. 4.78 µV D. 47.8 µV

Description : Two resistors, 20kΩ, and 50kΩ are at ambient temperature. Calculate for a bandwidth equal to 100kHz, the thermal noise voltage for the two resistors connected in parallel. A. 0.4782µV B. 4278 µV C. 4.78 µV D. 47.8 µV

Last Answer : C. 4.78 µV

Two 10 Ω resistors are connected in parallel, their equivalent resistance is A. 5 ΩB. 0.2 ΩC. 15 ΩD. 20 Ω

Description : Two 10 Ω resistors are connected in parallel, their equivalent resistance isA. 5 Ω B. 0.2 Ω C. 15 Ω D. 20 Ω

Last Answer :  5 Ω

List specifications of resistors and explain any two.

Description : List specifications of resistors and explain any two.

Last Answer : List specifications of resistors are as follows: 1. Maximum voltage rating. 2. Power rating. 3. Temperature co- efficient of resistance. 4. Tolerance. 5. Operating temperature. 6. Ohmic ... form of energy. Tolerance: It is defined as deviation from nominal value of resistance in percent.

Two identical resistors are connected in parallel and consume 200 watts together. A third identical resistor is added in parallel. The total power consumed is: w) 100 watts x) 200 watts y) 300 watts z) 400 watts

Description : Two identical resistors are connected in parallel and consume 200 watts together. A third identical resistor is added in parallel. The total power consumed is: w) 100 watts x) 200 watts y) 300 watts z) 400 watts

Last Answer : ANSWER: Y -- 300 WATTS

State any two types of resistors. Give one application of each.

Description : State any two types of resistors. Give one application of each.

Last Answer : Types of resistors with their applications: i) Carbon composition resistor: Potential divider, welding control circuits, power supplies, H. V. and high impulse circuits as switching spark ... vi)Cermet resistors: used in printers, automotive, computers, cell phones & battery chargers.

Two series resistors are connected to an ac source. If there are 7.5 V rms across one resistor

Description : Two series resistors are connected to an ac source. If there are 7.5 V rms across one resistor and 4.2 V rms across the other, the peak source voltage is? A.16.54 V B.1.65 V C.10.60 V D.5.93 V

Last Answer : Two series resistors are connected to an ac source. If there are 7.5 V rms across one resistor and 4.2 V rms across the other, the peak source voltage is? A.16.54 V B.1.65 V C.10.60 V D.5.93 V

When two 100 kΩ resistors are connected in parallel, net resistance is

Description : When two 100 kΩ resistors are connected in parallel, net resistance is

Last Answer : When two 100 kΩ resistors are connected in parallel, net resistance is 50 kΩ

A two-phase generator is connected to two 9012 load resistors. Each coil generates 120 V ac. The value of ...

Description : A two-phase generator is connected to two 90Ω load resistors. Each coil generates 120 V ac. The value of current flowing through the common neutral line will be: A. 1.33 A B. 1.88 A C. 2.66 A D. 1.77 A

Last Answer : A two-phase generator is connected to two 90Ω load resistors. Each coil generates 120 V ac. The value of current flowing through the common neutral line will be: 1.77 A

Two 1 kilo ohm, 1/2 W resistors are connected in series. Their combined resistance value and wattage will be

Last Answer : Two 1 kilo-ohm 1/2 W resistors are connected in series. Their combined resistance value and wattage will be 2 kΩ, 1 W.

If two parallel-connected resistors dissipate 6 watts and 10 watts of power, then what is the total power loss?

Last Answer : If two parallel-connected resistors dissipate 6 watts and 10 watts of power, then 16 watts is the total power loss.

Two resistors are said to be connected in series when?

Description : Two resistors are said to be connected in series when?

Last Answer : Two resistors are said to be connected in series when same current passes in turn through both.