The amount of backscattered optical power at each point depends on what two properties?

The amount of backscattered optical power at each point  depends on what two properties?
by

1 Answer

Answer :

Forward optical power and backscatter capture coefficient.
by

Related questions

The amount of optical power coupled into an optical fiber depends on what four factors?

Description : The amount of optical power coupled into an optical fiber depends on what four factors?

Last Answer : (1) The angles over which the light is emitted. (2) The size of the source's light-emitting area relative to the fiber core size. (3) The alignment of the source and fiber. (4) The coupling characteristics of the fiber (such as the NA and the refractive index profile)

Quality fiber-end preparation is essential for proper system operation. What properties must an optical fiber-end face have to ensure proper fiber connection?

Description : Quality fiber-end preparation is essential for proper system operation. What properties must an optical fiber-end face have to ensure proper fiber connection?

Last Answer : Be flat, smooth, and perpendicular to the fiber axis.

Which type of optical splitter (Y-coupler or T-coupler) splits only a small amount of power from the input fiber to one of the output fibers?

Description : Which type of optical splitter (Y-coupler or T-coupler) splits only a small amount of power from the input fiber to one of the output fibers?

Last Answer : T-coupler

Which performance parameter is the minimum amount of optical power required to achieve a specific bit-error rate (BER) in digital systems or a given signal-to-noise ratio (SNR) in analog systems?

Description : Which performance parameter is the minimum amount of optical power required to achieve a specific bit-error rate (BER) in digital systems or a given signal-to-noise ratio (SNR) in analog systems?

Last Answer : Receiver sensitivity.

The amount of heat required to change a boiling liquid to a gas at the same temperature depends on one of the following properties of the liquid. Does it depend on the liquid's: w) heat of fusion x) heat of vaporization y) temperature z) density

Description : The amount of heat required to change a boiling liquid to a gas at the same temperature depends on one of the following properties of the liquid. Does it depend on the liquid's: w) heat of fusion x) heat of vaporization y) temperature z) density

Last Answer : ANSWER: X -- HEAT OF VAPORIZATION

Define the loss in optical power through a connection.

Description : Define the loss in optical power through a connection.

Last Answer : loss = 10log

Which semiconductor sources (LD or LED) emit more focused light and are capable of launching sufficient optical power into both single mode and multimode fibers?

Description : Which semiconductor sources (LD or LED) emit more focused light and are capable of launching sufficient optical power into both single mode and multimode fibers?

Last Answer : LDs.

LEDs operating at 850 nm provide sufficient optical power for short-distance, low-bandwidth multimode systems. List three conditions that prevent the use of LEDs in longer distance, higher bandwidth multimode systems.

Description : LEDs operating at 850 nm provide sufficient optical power for short-distance, low-bandwidth multimode systems. List three conditions that prevent the use of LEDs in longer distance, higher bandwidth multimode systems.

Last Answer : Multimode fiber dispersion, the relatively high fiber attenuation, and the LED's relatively low optical output power.

When is an optical power meter measurement recommended for conducting field measurements on installed optical fiber cables or cable plants?

Description : When is an optical power meter measurement recommended for conducting field measurements on installed optical fiber cables or cable plants?

Last Answer : When an installed optical fiber cable or cable plant is less than 50 meters in length.

Describe the -3 decibel (dB) optical power frequency (f3dB).

Description : Describe the -3 decibel (dB) optical power frequency (f3dB).

Last Answer : The -3 decibel (dB) is the lowest frequency at which the magnitude of the fiber frequency response has decreased to one half its zero-frequency value.

The peak power of a radar depends on the interrelationship of what other factors?

Description : The peak power of a radar depends on the interrelationship of what other factors?

Last Answer : Average power, pulse width, and prt.

Which type of fiber optic connector (butt-jointed or expanded beam) brings the prepared ends of two optical fibers into close contact?

Description : Which type of fiber optic connector (butt-jointed or expanded beam) brings the prepared ends of two optical fibers into close contact?

Last Answer : Butt-jointed connectors.

Give two reasons why optical fiber manufacturers depart from the traditional circular core and cladding, low-loss glass fiber design?

Description : Give two reasons why optical fiber manufacturers depart from the traditional circular core and cladding, low-loss glass fiber design?

Last Answer : To increase performance and reduce cost

List the two principal optical detectors used in fiber optic systems.

Description : List the two principal optical detectors used in fiber optic systems.

Last Answer : The semiconductor positive-intrinsic-negative (PIN) photodiode and avalanche photodiode (APD).

Two methods describe how light propagates along an optical fiber. These methods define two theories of light propagation. What do we call these two theories?

Description : Two methods describe how light propagates along an optical fiber. These methods define two theories of light propagation. What do we call these two theories?

Last Answer : The ray theory and the mode theory.

What are the two basic types of optical fibers?

Description : What are the two basic types of optical fibers?

Last Answer : Multimode and single mode fibers.

What is the basic fiber cleaving technique for preparing optical fibers for coupling?

Description : What is the basic fiber cleaving technique for preparing optical fibers for coupling?

Last Answer : Score-and-break.

Which type of optical source tends to operate at higher drive currents to produce light?

Description : Which type of optical source tends to operate at higher drive currents to produce light?

Last Answer : Laser.

Which type of optical source usually lacks reflective facets and in some cases are designed to suppress reflections back into the active region?

Description : Which type of optical source usually lacks reflective facets and in some cases are designed to suppress reflections back into the active region?

Last Answer : LED.

Which types of LEDs are the preferred optical sources for short-distance, low-data-rate fiber optic systems?

Description : Which types of LEDs are the preferred optical sources for short-distance, low-data-rate fiber optic systems?

Last Answer : SLEDs and ELEDs.

Which part of a fiber optic transmitter converts the processed electrical signal to an optical signal?

Description : Which part of a fiber optic transmitter converts the processed electrical signal to an optical signal?

Last Answer : The optical source.

Describe an optical fiber cable component (OFCC).

Description : Describe an optical fiber cable component (OFCC).

Last Answer : OFCCs are tight-buffer fiber surrounded by arimid yarn and a low-halogen outer jacket.

List the three techniques used by manufacturers to buffer optical fibers.

Description : List the three techniques used by manufacturers to buffer optical fibers.

Last Answer : Tight-buffered, loose-tube, and gel-filled loose-tube.

List three benefits that properly cabled optical fibers provide.

Description : List three benefits that properly cabled optical fibers provide.

Last Answer : a. Protect optical fibers from damage or breakage during installation and over the fiber's lifetime. b. Provide stable fiber transmission characteristics compared with uncabled fibers. c. Maintain the physical integrity of the optical fiber.

List the types of materials used in fabricating low-loss, long wavelength optical fibers.

Description : List the types of materials used in fabricating low-loss, long wavelength optical fibers.

Last Answer : Heavy-metal fluorides, chalcogenide glasses, and crystalline materials.

Multimode optical fibers can have a step-index or graded index refractive index profile. Which fiber, multimode step-index or multimode graded-index fiber, usually performs better?

Description : Multimode optical fibers can have a step-index or graded index refractive index profile. Which fiber, multimode step-index or multimode graded-index fiber, usually performs better?

Last Answer : Multimode graded-index fiber

Describe the operation of an optical detector

Description : Describe the operation of an optical detector

Last Answer : It is a transducer that converts an optical signal into an electrical signal. It does this by generating an electrical current proportional to the intensity of incident optical radiation.

If an installed optical fiber cable does not have connectors or terminations on both ends, how should the cable be tested?

Description : If an installed optical fiber cable does not have connectors or terminations on both ends, how should the cable be tested?

Last Answer : With an OTDR unless it is less than 50 meters in length. If it is less than 50 meters in length, continuity should be verified with a flashlight.

Delay differences between the source wavelengths occur as the optical signal propagates along the fiber. What is this called?

Description : Delay differences between the source wavelengths occur as the optical signal propagates along the fiber. What is this called?

Last Answer : Differential group delay t(l).

A mode filter is a device that attenuates specific modes propagating in the core of an optical fiber. What mode propagating along single mode fibers do mode filters eliminate?

Description : A mode filter is a device that attenuates specific modes propagating in the core of an optical fiber. What mode propagating along single mode fibers do mode filters eliminate?

Last Answer : Second-order mode.

optical launch conditions exists if the launch spot size and angular distribution are larger than that of the fiber core?

Description : optical launch conditions exists if the launch spot size and angular distribution are larger than that of the fiber core?

Last Answer : Overfilled.

Does underfilling a multimode optical fiber excite mainly high-order or low-order modes?

Description : Does underfilling a multimode optical fiber excite mainly high-order or low-order modes?

Last Answer : Low-order modes.

Will an optical fiber's attenuation coefficient vary with changes in wavelength?

Description : Will an optical fiber's attenuation coefficient vary with changes in wavelength?

Last Answer : Yes.

Optical fibers or cables should never be bent at a radius of curvature smaller than a certain value. Identify this radius of curvature Optical fibers or cables should never be bent at a radius of curvature smaller than a certain value. Identify this radius of curvature

Description : Optical fibers or cables should never be bent at a radius of curvature smaller than a certain value. Identify this radius of curvature

Last Answer : Minimum bend radius.

What are the main causes of absorption in optical fiber?

Description : What are the main causes of absorption in optical fiber?

Last Answer : Intrinsic and extrinsic material properties.

What type of optical fiber operates below the cutoff

Description : What type of optical fiber operates below the cutoff

Last Answer : The order of a mode is indicated by the number of field maxima within the core of the fiber. The order of a mode is also determined by the angle that the wavefront makes with the axis of the fiber

A light ray incident on the optical fiber core is propagated along the fiber. Is the angle of incidence of the light ray entering the fiber larger or smaller than the acceptance angle

Description : A light ray incident on the optical fiber core is propagated along the fiber. Is the angle of incidence of the light ray entering the fiber larger or smaller than the acceptance angle

Last Answer : Smaller.

List the three parts of an optical fiber.

Description : List the three parts of an optical fiber.

Last Answer : Core, cladding, and coating or buffer.

The index of refraction measures the speed of light in an optical fiber. Will light travel faster in an optically dense material or in one that is less dense?

Description : The index of refraction measures the speed of light in an optical fiber. Will light travel faster in an optically dense material or in one that is less dense?

Last Answer : Light will travel faster in an optical material that is less dense.

What is the basic optical-material property relevant to optical fiber light transmission?

Description : What is the basic optical-material property relevant to optical fiber light transmission?

Last Answer : The index of refraction.

Low-order and high-order modes propagate along an optical fiber. How are modes determined to be low-order or high order modes?

Description : Low-order and high-order modes propagate along an optical fiber. How are modes determined to be low-order or high order modes?

Last Answer : Depends on the bending caused by the velocity difference of the wave traveling through different mediums

Which type of optical fiber (multimode or single mode) tends to have lower loss and produces less signal distortion?

Description : Which type of optical fiber (multimode or single mode) tends to have lower loss and produces less signal distortion?

Last Answer : Single mode fiber.

How can loss be reduced during construction (or fabrication) of optical fibers?

Description : How can loss be reduced during construction (or fabrication) of optical fibers?

Last Answer : By removing the impurities from optical fiber.

In 1969, what did several scientists conclude about optical fiber loss?

Description : In 1969, what did several scientists conclude about optical fiber loss?

Last Answer : mpurities in the fiber material caused the signal loss in optical fibers. The basic fiber material did not prevent the light signal from reaching the end of the fiber.

What mechanisms in the fiber waveguides weaken and distort the optical signal?

Description : What mechanisms in the fiber waveguides weaken and distort the optical signal?

Last Answer : Scattering, absorption, and dispersion.

The pH of an amino acid depends (A) Optical rotation (B) Dissociation constant (C) Diffusion coefficient(D) Chain length

Description : The pH of an amino acid depends (A) Optical rotation (B) Dissociation constant (C) Diffusion coefficient(D) Chain length

Last Answer : Answer : B

The optical property of a water body depends on: (A) Absorption by the dissolved material (B) Absorption by the suspended particulate matter (C) Scattering by the suspended particulate matter (D) All of these

Description : The optical property of a water body depends on: (A) Absorption by the dissolved material (B) Absorption by the suspended particulate matter (C) Scattering by the suspended particulate matter (D) All of these

Last Answer : Answer: Option D

For all transparent material substances, the index of refraction A. A.is less than 1 B. B.is greater than 1 C. C.is equal to 1 D. Could be any of the given answers; it all depends on optical density

Description : For all transparent material substances, the index of refraction A. A.is less than 1 B. B.is greater than 1 C. C.is equal to 1 D. Could be any of the given answers; it all depends on optical density

Last Answer : B. B.is greater than 1

What are some of the properties of optical fibre?

Description : What are some of the properties of optical fibre?

Last Answer : It's not brittle,but it's not tough or strong either.It's thin and it's subjected to breakage which is known as fibre cut in technical terms.They are used in communication process to ... engineering with respect to design and afety parameters.Moreover, it gives a very ugly look to the surroundings.

Mutarotation refers to change in (A) pH (B) Optical rotation (C) Conductance (D) Chemical properties

Description : Mutarotation refers to change in (A) pH (B) Optical rotation (C) Conductance (D) Chemical properties

Last Answer : B