Description : As per IS: 456, permissible bond stress for plain bars in tension, in working stress method, where M20, is the grade of concrete [ A ] 0.6 N/mm2 [ B ] 0.8 N/mm2 [ C ] 1.0 N/mm2 [ D ] 1.2 N/mm2
Last Answer : [ B ] 0.8 N/mm2
Description : As per IS;456, in working stress method of design, permissible tensile stress for M20 grade concrete is given by [ A ] 1. 2 N/mm2 [ B ] 1.5 N/mm2 [ C ] 2.0 N/mm2 [ D ] 2.8 N/mm2
Last Answer : [ D ] 2.8 N/mm2
Description : As per IS: 456, permissible direct compressive stress M20 grade concrete in working stress method of designer [ A ] 5.0 N/mm2 [ B ] 7.0 N/mm2 [ C ] 10.0 N/mm2 [ D ] 20.0 N/mm2
Last Answer : [ A ] 5.0 N/mm2
Description : In working stress method of design, permissible compressive bending stress for M20 grade concrete is given by [ A ] 5.0 N/mm2 [ B ] 7.0 N/mm2 [ C ] 10.0 N/mm2 [ D ] 20 N/mm2
Last Answer : [ B ] 7.0 N/mm2
Description : As per IS :456-1978, the permissible value of bond – stress for M15 grade of concrete is (a) 0.5 N/mm2 (b) 1 N/mm2 (c) 1.5 N/mm2 (d) 2 N/mm2
Last Answer : (b) 1 N/mm2
Description : The ultimate average anchorage bond stress for plain bars in tension is _______ if the grade of concrete is M20 [ A ] 1.60 N/mm2 [ B ] 1.92 N/mm2 [ C ] 2.24 N/mm2 [ D ] 2.40 N/mm2
Last Answer : [ B ] 1.92 N/mm2
Description : Maximum allowable shear stress for M25 grade concrete is [ A ] 2.5 N/mm2 [ B ] 2.8 N/mm2 [ C ] 3.1 N/mm2 [ D ] 3.5 N/mm2
Last Answer : [ C ] 3.1 N/mm2
Description : As per 1S: 456-2000, minimum grade of concrete in seat water constructions is [ A ] M20 [ B ] M25 [ C ] M30 [ D ] M50
Last Answer : [ C ] M30
Description : Minimum grade of concrete for R.C.C. should be _________ , as per IS. 456-2000 [ A ] M10 [ B ] M14 [ C ] M20 [ D ] M25
Last Answer : [ C ] M20
Description : As per IS: 456-2000, recommended value for standard deviation for concrete mix from M30 to M50 is [ A ] 1 N/mm2 [ B ] 2 N/mm2 [ C ] 4 N/mm2 [ D ] 5 N/mm2
Last Answer : [ D ] 5 N/mm2
Description : As per IS: 456-2000, modulus of elasticity of concrete (in N/mm2) is given by [ A ] 5700 vfCK [ B ] 5000 vfCK [ C ] 3700 vfCK [ D ] 3000 vfCK
Last Answer : [ B ] 5000 vfCK
Description : If a solid shaft (diameter 20 cm, length 400 cm, N = 0.8 × 105 N/mm2 ) when subjected to a twisting moment, produces maximum shear stress of 50 N/mm2 , the angle of twist in radians, is (A) 0.001 (B) 0.002 (C) 0.0025 (D) 0.003
Last Answer : (C) 0.0025
Description : What is the shear stress acting along the neutral axis of triangular beam section, with base 60 mm and height 150 mm, when shear force of 30 kN acts? a. 15.36 N/mm2 b. 10.6 N/mm2 c. 8.88 N/mm2 d. Insufficient data
Last Answer : c. 8.88 N/mm2
Description : A solid shaft has diameter 80 mm. It is subjected to a torque of 4 KNm. The maximum shear stress induced in the shaft would be (a) 75/p N/mm2 (b) 250/p N/mm2 (c) 125/p N/mm2 (d) 150/p N/mm2
Last Answer : (c) 125/p N/mm2
Description : Torque and bending moment of 100 kN.m and 200 kN.m acts on a shaft which has external diameter twice of internal diameter. What is the external diameter of the shaft which is subjected to a maximum shear stress of 90 N/mm2? a. 116.5 mm b. 233.025 mm c. 587.1 mm d. 900 mm
Last Answer : c. 587.1 mm
Description : What is the maximum shear stress induced in a solid shaft of 50 mm diameter which is subjected to both bending moment and torque of 300 kN.mm and 200 kN.mm respectively? a. 9.11 N/mm2 b. 14.69 N/mm2 c. 16.22 N/mm2 d. 20.98 N/mm2
Last Answer : b. 14.69 N/mm2
Description : A square object of 4 mm is subjected to a force of 3000 N. What is the maximum allowable shear stress acting on it? a. 250.14 mm2 b. 281.25 mm2 c. 400.32 mm2 d. 500 mm2
Last Answer : b. 281.25 mm2
Description : What is the average shear stress acting on a rectangular beam, if 50 N/mm2is the maximum shear stress acting on it? a. 31.5 N/mm2 b. 33.33 N/mm2 c. 37.5 N/mm2 d. 42.5 N/mm2
Last Answer : b. 33.33 N/mm2
Description : Which of the following grade is not recommended by IS 456-1978? (a) M10 (b) M20 (c) M40 (d) M55
Last Answer : (d) M55
Description : A simply supported rolled steel joist 8 m long carries a uniformly distributed load over it span so that the maximum bending stress is 75 N/mm². If the slope at the ends is 0.005 radian and the value of E = 0.2 ... joist, is (A) 200 mm (B) 250 mm (C) 300 mm (D) 400 mm
Last Answer : (D) 400 mm
Description : What is the shear stress acting on the outer surface of a hollow shaft subjected to a torque of 100 Nm?(The inner and outer diameter of the shaft is 15 mm and 30 mm respectively.) a. 50.26 N/mm2 b. 40.24 N/mm2 c. 20.120 N/mm2 d. 8.74 N/mm2
Last Answer : c. 20.120 N/mm2
Description : If a concrete column 200 200 mm in cross-section is reinforced with four steel bars of 1200 mm2 total cross-sectional area. Calculate the safe load for the column if permissible stress in concrete is 5 N/mm2 ... 15 Ec (A) 264 MN (B) 274 MN (C) 284 MN (D) 294 MN
Last Answer : (C) 284 MN
Description : The effective depth of a singly reinforced rectangular beam is 300mm. the section is over-reinforced and the neutral axis is 120mm below the top. If the maximum stress attained by concrete is 5N/mn2 and the modular ratio ... in the steel will (a) 130N/mm2 (b) 135N/mm2 (c) 160N/mm2 (d) 180N/mm2
Last Answer : (b) 135N/mm2
Description : For a reinforced concrete beam section, the shape of shear stress diagram is (a) Parabolic over the whole section with maximum value at the neutral axis. (b) Parabolic above the neutral axis and rectangular below the neutral axis. (c) Linearly varying as the distance form the N.A. (d) All the above.
Last Answer : (b) Parabolic above the neutral axis and rectangular below the neutral axis.
Description : If yielding strength=400N/mm2, the find the permissible shear stress according to ASME standards. a) 72 N/mm2 b) 76 N/mm2 c) 268 N/mm2 d) 422 N/mm2
Last Answer : a) 72 N/mm2
Description : If the average bending stress is 6 kg/cm2 for M 150 grade concrete, the length of embedment of a bar of diameter d according to I.S. 456 specifications, is (A) 28 d (B) 38 d (C) 48 d (D) 58 d
Last Answer : Answer: Option D
Description : Stress may be expressed in Newtons (A) Per millimetre square (N/mm2 ) (B) Per centimetre square (N/cm2 ) (C) Per metre square (N/m2 ) (D) None of these
Last Answer : (A) Per millimetre square (N/mm2 )
Description : As per IS: 1139, permissible stress in compression steel reinforcement for High Yield strength deformed bars is [ A ] 140 N/mm2 [ B ] 190 N/mm2 [ C ] 230 N/mm2 [ D ] 415 N/mm2
Last Answer : [ B ] 190 N/mm2
Description : A steel bar 20 mm in diameter simply-supported at its ends over a total span of 40 cm carries a load at its centre. If the maximum stress induced in the bar is limited to N/mm2, the bending strain energy stored in the ... (A) 411 N mm (B) 511 N mm (C) 611 N mm (D) 711 N mm
Last Answer : (C) 611 N mm
Description : The ratio of differenct ingredients (cement, sand and aggregate) in concrete mix of grade M20 is. (a) 1:1:2 (b) 1:1.5:2 (c) 1:2:4 (d) 1:3:6
Last Answer : (b) 1:1.5:2
Description : For lime concrete, (A) Slump is 50 to 75 mm (B) Flexural strength at 90 days is 0.2 N/mm2 (C) Compressive strength at 90 days is 1.5 N/mm2 (D) All the above
Description : Find the shear stress in a flange at the junction of hub in rigid flanged coupling if torsional moment is 2980N-m and diameter of hub being 125mm. Also the thickness of flange is 25mm. a) 6.77N/mm2 b) 10.24N/mm2 c) 4.84N/mm2 d) 4.22N/mm2
Last Answer : c) 4.84N/mm2
Description : According to I.S. : 456 specifications, the safe diagonal tensile stress for M 150 grade concrete, is (A) 5 kg/cm2 (B) 10 kg/cm2 (C) 15 kg/cm2 (D) 20 kg/cm
Last Answer : Answer: Option A
Description : As per IS:456-1978, the concrete mixes are designated into (a) 4 grades (b) 5 grades (c) 6 grades (d) 7 grades
Last Answer : (d) 7 grades
Description : If the strain energy stored per unit volume in a hollow shaft subjected to a pure torque when t attains maximum shear stress fs the ratio of inner diameter to outer diameter, is 17/64 (fs/N) (A) 1/2 (B) 1/3 (C) 1/4 (D) 1/5
Last Answer : (C) 1/4
Description : A water main 1 m in diameter contains a fluid having pressure 1 N/mm2. If the maximum permissible tensile stress in the metal is 20 N/mm2, th thickness of the metal required would be a) 2 cm b) 2.5cm c) 1 cm d) 0.5 cm
Last Answer : b) 2.5cm
Description : As per IS:456, the strength of concrete sample is less than [ A ] The characteristic strength minus 1.35times the standard deviation [ B ] 0.80 times the characteristic strength [ C ] Greater of (a) and (b) [ D ] None of the above
Last Answer : [ C ] Greater of (a) and (b)
Description : A load of 1960 N is raised at the end of a steel wire. The minimum diameter of the wire so that stress in the wire does not exceed 100 N/mm2 is: (A) 4.0 mm (B) 4.5 mm (C) 5.0 mm (D) 5.5 mm
Last Answer : (C) 5.0 mm
Description : In working stress method of design, the factor of safety for concrete and steel respectively are [ A ] 3.0 and 1.8 [ B ] 3.0 and 1.18 [ C ] 3.0 and 1.15 [ D ] 1.5 and 1.5
Last Answer : [ A ] 3.0 and 1.8
Description : According to IS: 456-2000 Maximum spacing of shear reinforcement in no case shall not exceed [ A ] 250 mm [ B ] 300 mm [ C ] 350 mm [ D ] 450 mm
Last Answer : [ B ] 300 mm
Description : The maximum shear stress (q) in concrete of a reinforced cement concrete beam is (A) Shear force/(Lever arm × Width) (B) Lever arm/(Shear force × Width) (C) Width/(Lever arm × Shear force) (D) (Shear force × Width)/Lever arm
Description : Inc case of prestressed concrete members, the bursting stresses develop at (a) Bond zone (b) Maximum bending moment zone (c ) Maximum shear stress zone (d) Anchorage zone
Last Answer : (d) Anchorage zone
Description : A compound bar consists of two bars of equal length. Steel bar cross-section is 3500 mm2 and that of brass bar is 3000 mm2 . These are subjected to a compressive load 100,000 N. If Eb = 0.2 MN/mm2 and Eb = 0.1 ... 6 N/mm2 s = 12 N/mm2 (D) b = 5 N/mm2 s = 10 N/mm
Last Answer : (A) b = 10 N/mm2 s = 20 N/mm
Description : What is the maximum principle stress induced in a solid shaft of 40 mm diameter which is subjected to both bending moment and torque of 300 kN.mm and 150 kN.mm respectively? a. 21.69 N/mm2 b. 28.1 N/mm2 c. 50.57 N/mm2 d. 52.32 N/mm2
Last Answer : c. 50.57 N/mm2
Description : A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and breadth of the key being 14mm and 80mm respectively. Find the shear stress induced in the key. a) 30.2N/mm2 b) 25.8N/mm2 c) 34.4N/mm2 d) None of the listed
Last Answer : b) 25.8N/mm2
Description : Nominal cover for M30 grade concrete in moderate exposure is (as per IS:456-2000) [ A ] 20 mm [ B ] 30 mm [ C ] 45 mm [ D ] 50 mm
Last Answer : [ B ] 30 mm
Description : An R.C.C. beam of 25 cm width and 50 cm effective depth has a clear span of 6 metres and carries a U.D.L. of 3000 kg/m inclusive of its self weight. If the lever arm constant for the section is 0.865, the maximum intensity ... , is (A) 8.3 kg/cm2 (B) 7.6 kg/cm2 (C) 21.5 kg/cm2 (D) 11.4 kg/cm2