Description : In working stress method of design, permissible compressive bending stress for M20 grade concrete is given by [ A ] 5.0 N/mm2 [ B ] 7.0 N/mm2 [ C ] 10.0 N/mm2 [ D ] 20 N/mm2
Last Answer : [ B ] 7.0 N/mm2
Description : As per IS;456, in working stress method of design, permissible tensile stress for M20 grade concrete is given by [ A ] 1. 2 N/mm2 [ B ] 1.5 N/mm2 [ C ] 2.0 N/mm2 [ D ] 2.8 N/mm2
Last Answer : [ D ] 2.8 N/mm2
Description : As per IS: 456, permissible bond stress for plain bars in tension, in working stress method, where M20, is the grade of concrete [ A ] 0.6 N/mm2 [ B ] 0.8 N/mm2 [ C ] 1.0 N/mm2 [ D ] 1.2 N/mm2
Last Answer : [ B ] 0.8 N/mm2
Description : As per IS:456, maximum shear stress for M20 glade concrete in working stress method is [ A ] 1.6 N/mm2 [ B ] 1.8 N/mm2 [ C ] 2.0 N/mm2 [ D ] 2.2 N/mm2
Last Answer : [ B ] 1.8 N/mm2
Description : As per IS :456-1978, the permissible value of bond – stress for M15 grade of concrete is (a) 0.5 N/mm2 (b) 1 N/mm2 (c) 1.5 N/mm2 (d) 2 N/mm2
Last Answer : (b) 1 N/mm2
Description : The ultimate average anchorage bond stress for plain bars in tension is _______ if the grade of concrete is M20 [ A ] 1.60 N/mm2 [ B ] 1.92 N/mm2 [ C ] 2.24 N/mm2 [ D ] 2.40 N/mm2
Last Answer : [ B ] 1.92 N/mm2
Description : As per 1S: 456-2000, minimum grade of concrete in seat water constructions is [ A ] M20 [ B ] M25 [ C ] M30 [ D ] M50
Last Answer : [ C ] M30
Description : Minimum grade of concrete for R.C.C. should be _________ , as per IS. 456-2000 [ A ] M10 [ B ] M14 [ C ] M20 [ D ] M25
Last Answer : [ C ] M20
Description : As per IS: 456-2000, recommended value for standard deviation for concrete mix from M30 to M50 is [ A ] 1 N/mm2 [ B ] 2 N/mm2 [ C ] 4 N/mm2 [ D ] 5 N/mm2
Last Answer : [ D ] 5 N/mm2
Description : As per IS: 456-2000, modulus of elasticity of concrete (in N/mm2) is given by [ A ] 5700 vfCK [ B ] 5000 vfCK [ C ] 3700 vfCK [ D ] 3000 vfCK
Last Answer : [ B ] 5000 vfCK
Description : If a concrete column 200 200 mm in cross-section is reinforced with four steel bars of 1200 mm2 total cross-sectional area. Calculate the safe load for the column if permissible stress in concrete is 5 N/mm2 ... 15 Ec (A) 264 MN (B) 274 MN (C) 284 MN (D) 294 MN
Last Answer : (C) 284 MN
Description : According to I.S. : 456 specifications, the safe diagonal tensile stress for M 150 grade concrete, is (A) 5 kg/cm2 (B) 10 kg/cm2 (C) 15 kg/cm2 (D) 20 kg/cm
Last Answer : Answer: Option A
Description : Which of the following grade is not recommended by IS 456-1978? (a) M10 (b) M20 (c) M40 (d) M55
Last Answer : (d) M55
Description : Maximum allowable shear stress for M25 grade concrete is [ A ] 2.5 N/mm2 [ B ] 2.8 N/mm2 [ C ] 3.1 N/mm2 [ D ] 3.5 N/mm2
Last Answer : [ C ] 3.1 N/mm2
Description : Minimum compressive strength of cement required at the age of 3 days for ordinary Portland cement of grade 33 is [ A ] 1.15 N/mm2 [ B ] 11.5 N/mm2 [ C ] 2.10 N/mm2 [ D ] 21 N/mm2
Last Answer : [ B ] 11.5 N/mm2
Description : As per IS: 1139, permissible stress in compression steel reinforcement for High Yield strength deformed bars is [ A ] 140 N/mm2 [ B ] 190 N/mm2 [ C ] 230 N/mm2 [ D ] 415 N/mm2
Last Answer : [ B ] 190 N/mm2
Description : If the permissible stress in steel in tension is 140 N/mm², then the depth of neutral axis for a singly reinforced rectangular balanced section will be (A) 0.35 d (B) 0.40 d (C) 0.45 d (D) Dependent on grade of concrete also
Last Answer : Answer: Option B
Description : For lime concrete, (A) Slump is 50 to 75 mm (B) Flexural strength at 90 days is 0.2 N/mm2 (C) Compressive strength at 90 days is 1.5 N/mm2 (D) All the above
Last Answer : Answer: Option D
Description : A water main 1 m in diameter contains a fluid having pressure 1 N/mm2. If the maximum permissible tensile stress in the metal is 20 N/mm2, th thickness of the metal required would be a) 2 cm b) 2.5cm c) 1 cm d) 0.5 cm
Last Answer : b) 2.5cm
Description : Permissible compressive strength of M 200 concrete grade is (A) 100 kg/cm2 (B) 150 kg/cm2 (C) 200 kg/cm2 (D) 250 kg/cm2
Last Answer : (C) 200 kg/cm2
Description : Permissible compressive strength of M 300 concrete grade is (A) 100 kg/cm2 (B) 150 kg/cm2 (C) 200 kg/cm2 (D) 300 kg/cm2
Last Answer : (D) 300 kg/cm2
Last Answer : Answer: Option C
Description : Permissible compressive strength of M 150 concrete grade is (A) 100 kg/cm2 (B) 150 kg/cm2 (C) 200 kg/cm2 (D) 250 kg/cm2
Description : Nominal cover for M30 grade concrete in moderate exposure is (as per IS:456-2000) [ A ] 20 mm [ B ] 30 mm [ C ] 45 mm [ D ] 50 mm
Last Answer : [ B ] 30 mm
Description : A compound bar consists of two bars of equal length. Steel bar cross-section is 3500 mm2 and that of brass bar is 3000 mm2 . These are subjected to a compressive load 100,000 N. If Eb = 0.2 MN/mm2 and Eb = 0.1 ... 6 N/mm2 s = 12 N/mm2 (D) b = 5 N/mm2 s = 10 N/mm
Last Answer : (A) b = 10 N/mm2 s = 20 N/mm
Description : If the average bending stress is 6 kg/cm2 for M 150 grade concrete, the length of embedment of a bar of diameter d according to I.S. 456 specifications, is (A) 28 d (B) 38 d (C) 48 d (D) 58 d
Description : The ratio of differenct ingredients (cement, sand and aggregate) in concrete mix of grade M20 is. (a) 1:1:2 (b) 1:1.5:2 (c) 1:2:4 (d) 1:3:6
Last Answer : (b) 1:1.5:2
Description : If the permissible compressive stress for a concrete in bending is C kg/m2 , the modular ratio is (A) 2800/C (B) 2300/2C (C) 2800/3C (D) 2800/C
Description : The modular ratio m of a concrete whose permissible compressive stress is C, may be obtained from the equation. (A) m = 700/3C (B) m = 1400/3C (C) m = 2800/3C (D) m = 3500/3C
Description : If the permissible compressive stress for a concrete in bending is ckg/m2, the modular ratio is (a) 2800/C (b) 2300/C (c) 2800/3C (d) 2800/4C
Last Answer : (d) 2800/4C
Description : Permissible width of crack at the surface of concrete for „moderate‟ environmental conditions according to IS : 456-2000 is [ A ] 0.1 mm [ B ] 0.2 mm [ C ] 0.3 mm [ D ] 0.4 mm
Last Answer : [ B ] 0.2 mm
Description : The compressive strength an ordinary Portland cement (1:3) after 7 days test should not be less than. (a) 11N/mm2 (b) 17.5 N/mm2 (c) 22 N/mm2 (d) 27.5N/m2
Last Answer : (b) 17.5 N/mm2
Description : A short column 20 cm 20 cm in section is reinforced with 4 bars whose area of cross section is 20 sq. cm. If permissible compressive stresses in concrete and steel are 40 kg/cm2 and 300 kg/cm2 , the Safe load on ... should not exceed (A) 4120 kg (B) 41,200 kg (C) 412,000 kg (D) None of these
Description : A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and height of the key being 14mm and 80mm respectively. Find the compressive stress induced in the key. a) 70.1 N/mm2 b) 51.6N/mm2 c) 45.5N/mm2 d) None of the listed
Last Answer : b) 51.6N/mm2
Description : If yielding strength=400N/mm2, the find the permissible shear stress according to ASME standards. a) 72 N/mm2 b) 76 N/mm2 c) 268 N/mm2 d) 422 N/mm2
Last Answer : a) 72 N/mm2
Description : If a solid shaft (diameter 20 cm, length 400 cm, N = 0.8 × 105 N/mm2 ) when subjected to a twisting moment, produces maximum shear stress of 50 N/mm2 , the angle of twist in radians, is (A) 0.001 (B) 0.002 (C) 0.0025 (D) 0.003
Last Answer : (C) 0.0025
Description : The grade of concrete not recommended by I.S. : 456, is (A) M 100 (B) M 200 (C) M 300 (D) M 500
Last Answer : (D) M 500
Description : A spring of mean radius 40 mm contains 8 action coils of steel (N = 80000 N/mm2 ), 4 mm in diameter. The clearance between the coils being 1 mm when unloaded, the minimum compressive load to remove the clearance, is (A) 25 N (B) 30 N (C) 35 N (D) 40 N
Last Answer : (C) 35 N
Description : If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the diameter of each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. Permissible tensile stress is 80N/mm2. a) 27mm b) 25mm c) 23mm d) 21mm
Last Answer : a) 27mm
Description : Stress may be expressed in Newtons (A) Per millimetre square (N/mm2 ) (B) Per centimetre square (N/cm2 ) (C) Per metre square (N/m2 ) (D) None of these
Last Answer : (A) Per millimetre square (N/mm2 )
Description : A steel bar 20 mm in diameter simply-supported at its ends over a total span of 40 cm carries a load at its centre. If the maximum stress induced in the bar is limited to N/mm2, the bending strain energy stored in the ... (A) 411 N mm (B) 511 N mm (C) 611 N mm (D) 711 N mm
Last Answer : (C) 611 N mm
Description : Regarding the working stress design of under reinforced concrete section, (a) The neutral axis depth will be greater than that of a balanced section. (b) The stress in steel intension will reach ... on the tension side is also be considered for calculating the moment of resistance of the section.
Last Answer : both b&c
Description : As per IS:456-1978, the concrete mixes are designated into (a) 4 grades (b) 5 grades (c) 6 grades (d) 7 grades
Last Answer : (d) 7 grades
Description : In general in the design of a section by limit method, it is assumed that [ A ] the stress in steel to reach its yield limit before concrete failure [ B ] the stress in concrete to ... in both concrete and steel reach their permissible values simultaneously [ D ] none of the above are correct
Last Answer : [ A ] the stress in steel to reach its yield limit before concrete failure
Description : The effective depth of a singly reinforced rectangular beam is 300mm. the section is over-reinforced and the neutral axis is 120mm below the top. If the maximum stress attained by concrete is 5N/mn2 and the modular ratio ... in the steel will (a) 130N/mm2 (b) 135N/mm2 (c) 160N/mm2 (d) 180N/mm2
Last Answer : (b) 135N/mm2
Description : Calculate the shaft diameter on rigidity basis if torsional moment is 196000N-mm, length of shaft is 1000mm. Permissible angle of twist per meter is 0.5’ and take G=79300N/mm2. a) None of the listed b) 41.2mm c) 35.8mm d) 38.8mm
Last Answer : b) 41.2mm
Description : A load of 1960 N is raised at the end of a steel wire. The minimum diameter of the wire so that stress in the wire does not exceed 100 N/mm2 is: (A) 4.0 mm (B) 4.5 mm (C) 5.0 mm (D) 5.5 mm
Last Answer : (C) 5.0 mm