A reinforced concrete cantilever porch has thickness t. The main reinforcing steel will be placed (a) At mid-thickness (b) At t/3 from the top (c) Close to the bottom surface (d) Close to the top surface

A reinforced concrete cantilever porch has thickness t. The main reinforcing steel will be placed
(a) At mid-thickness (b) At t/3 from the top
(c) Close to the bottom surface (d) Close to the top surface
by

1 Answer

Answer :

(d) Close to the top surface
by

Related questions

A reinforced concrete cantilever beam is 3.6 m long, 25 cm wide and has its lever arm 40 cm. It carries a load of 1200 kg at its free end and vertical stirrups can carry 1800 kg. Assuming concrete to carry one-third of the diagonal tension and ignoring the weight of the beam, the number of shear stirrups required, is (A) 30 (B) 35 (C) 40 (D) 45

Description : A reinforced concrete cantilever beam is 3.6 m long, 25 cm wide and has its lever arm 40 cm. It carries a load of 1200 kg at its free end and vertical stirrups can carry 1800 kg. Assuming concrete to carry one- ... beam, the number of shear stirrups required, is (A) 30 (B) 35 (C) 40 (D) 45

Last Answer : Answer: Option C

A reinforcing slab, build monolithically with the supporting columns and is reinforced in two or more directions, without any provision of beams is called a (a) Two way slab (b) Flat slab (c) Continus slab (d) Cireulashion

Description : A reinforcing slab, build monolithically with the supporting columns and is reinforced in two or more directions, without any provision of beams is called a (a) Two way slab (b) Flat slab (c) Continus slab (d) Cireulashion

Last Answer : (b) Flat slab

The effective depth of a singly reinforced rectangular beam is 300mm. the section is over-reinforced and the neutral axis is 120mm below the top. If the maximum stress attained by concrete is 5N/mn2 and the modular ratio is 18, then the stress developed in the steel will (a) 130N/mm2 (b) 135N/mm2 (c) 160N/mm2 (d) 180N/mm2

Description : The effective depth of a singly reinforced rectangular beam is 300mm. the section is over-reinforced and the neutral axis is 120mm below the top. If the maximum stress attained by concrete is 5N/mn2 and the modular ratio ... in the steel will (a) 130N/mm2 (b) 135N/mm2 (c) 160N/mm2 (d) 180N/mm2

Last Answer : (b) 135N/mm2

According to I.S.: 456, 1978 the thickness of reinforced concrete footing on piles at its edges, is kept less than (A) 20 cm (B) 30 cm (C) 40 cm (D) 75 cm

Description : According to I.S.: 456, 1978 the thickness of reinforced concrete footing on piles at its edges, is kept less than (A) 20 cm (B) 30 cm (C) 40 cm (D) 75 cm

Last Answer : Answer: Option B

According to I.S.: 456, 1978 the thickness of reinforced concrete footing on piles at its edges, is kept less than (A) 5 cm (B) 10 cm (C) 15 cm (D) 20 cm

Description : According to I.S.: 456, 1978 the thickness of reinforced concrete footing on piles at its edges, is kept less than (A) 5 cm (B) 10 cm (C) 15 cm (D) 20 cm

Last Answer : Answer: Option C

In reinforced concrete footing on soil, the minimum thickness at edge should not be less than (A) 100 mm (B) 150 mm (C) 200 mm (D) 250 mm

Description : In reinforced concrete footing on soil, the minimum thickness at edge should not be less than (A) 100 mm (B) 150 mm (C) 200 mm (D) 250 mm

Last Answer : Answer: Option B

The minimum thickness of the cover at the end of a reinforcing bar should not be less than twice the diameter of the bar subject to a minimum of (A) 10 mm (B) 15 mm (C) 20 mm (D) 25 mm

Description : The minimum thickness of the cover at the end of a reinforcing bar should not be less than twice the diameter of the bar subject to a minimum of (A) 10 mm (B) 15 mm (C) 20 mm (D) 25 mm

Last Answer : Answer: Option D

The ratio of the diameter of reinforcing bars and the slab thickness is (A) 1/4 (B) 1/5 (C) 1/6 (D) 1/8

Description : The ratio of the diameter of reinforcing bars and the slab thickness is (A) 1/4 (B) 1/5 (C) 1/6 (D) 1/8

Last Answer : (D) 1/8

In a simply supported reinforced concrete beam, the reinforcement is placed. (a) Above the neutral axis (b) Below the neutral axis (c) At the neutral axis (d) None of these

Description : In a simply supported reinforced concrete beam, the reinforcement is placed. (a) Above the neutral axis (b) Below the neutral axis (c) At the neutral axis (d) None of these

Last Answer : (b) Below the neutral axis

The stem of a cantilever retaining wall which retains earth level with top is 6 m. If the angle of repose and weight of the soil per cubic metre are 30° and 2000 kg respectively, the effective width of the stem at the bottom, is (A) 51.5 (B) 52.5 (C) 53.5 (D) 54.5

Description : The stem of a cantilever retaining wall which retains earth level with top is 6 m. If the angle of repose and weight of the soil per cubic metre are 30° and 2000 kg respectively, the effective width of the stem at the bottom, is (A) 51.5 (B) 52.5 (C) 53.5 (D) 54.5

Last Answer : Answer: Option C

For the supply of materials for concrete, form work reinforcing and placing of concrete, removal of form work and curing of concrete, number of bar(s) required on bar chart, is (A) 1 (B) 2 (C) 3 (D) 4

Description : For the supply of materials for concrete, form work reinforcing and placing of concrete, removal of form work and curing of concrete, number of bar(s) required on bar chart, is (A) 1 (B) 2 (C) 3 (D) 4

Last Answer : (A) 1

A piece of metal of specific gravity 13.6 is placed in mercury of specific gravity 13.6, what fraction of it volume is under mercury? (A) The metal piece will simply float over the mercury (B) The metal piece will be immersed in mercury by half (C) Whole of the metal piece will be immersed with its top surface just at mercury level (D) Metal piece will sink to the bottom

Description : A piece of metal of specific gravity 13.6 is placed in mercury of specific gravity 13.6, what fraction of it volume is under mercury? (A) The metal piece will simply float over the mercury (B ... will be immersed with its top surface just at mercury level (D) Metal piece will sink to the bottom

Last Answer : Answer: Option C

If a concrete column 200 × 200 mm in cross-section is reinforced with four steel bars of 1200 mm2 total cross-sectional area. Calculate the safe load for the column if permissible stress in concrete is 5 N/mm2 and Es is 15 Ec (A) 264 MN (B) 274 MN (C) 284 MN (D) 294 MN

Description : If a concrete column 200 200 mm in cross-section is reinforced with four steel bars of 1200  mm2  total cross-sectional area. Calculate the safe load for the column if permissible stress in  concrete is 5 N/mm2 ... 15 Ec (A) 264 MN  (B) 274 MN  (C) 284 MN  (D) 294 MN 

Last Answer : (C) 284 MN 

If permissible working stresses in steel and concrete are respectively 1400 kg/cm2 and 80 kg/cm2 and modular ratio is 18, in a beam reinforced in tension side and of width 30 cm and having effective depth 46 cm, the lever arms of the section, is (A) 37 cm (B) 38 cm (C) 39 cm (D) 40 cm

Description : If permissible working stresses in steel and concrete are respectively 1400 kg/cm2 and 80 kg/cm2 and modular ratio is 18, in a beam reinforced in tension side and of width 30 cm and having effective depth 46 cm, the lever arms of the section, is (A) 37 cm (B) 38 cm (C) 39 cm (D) 40 cm

Last Answer : Answer: Option D

Steel beam theory is used for (A) Design of simple steel beams (B) Steel beams encased in concrete (C) Doubly reinforced beams ignoring compressive stress in concrete (D) Beams if shear exceeds 4 times allowable shear stress

Description : Steel beam theory is used for (A) Design of simple steel beams (B) Steel beams encased in concrete (C) Doubly reinforced beams ignoring compressive stress in concrete (D) Beams if shear exceeds 4 times allowable shear stress

Last Answer : Answer: Option C

A short column 20 cm × 20 cm in section is reinforced with 4 bars whose area of cross section is 20 sq. cm. If permissible compressive stresses in concrete and steel are 40 kg/cm2 and 300 kg/cm2 , the Safe load on the column, should not exceed (A) 4120 kg (B) 41,200 kg (C) 412,000 kg (D) None of these

Description : A short column 20 cm 20 cm in section is reinforced with 4 bars whose area of cross section is 20 sq. cm. If permissible compressive stresses in concrete and steel are 40 kg/cm2 and 300 kg/cm2 , the Safe load on ... should not exceed (A) 4120 kg (B) 41,200 kg (C) 412,000 kg (D) None of these

Last Answer : Answer: Option B

In a singly reinforced beam, if the permissible stress in concrete reaches earlier than that in steel, the beam section is called (A) Under-reinforced section (B) Over reinforced section (C) Economic section (D) Critical section

Description : In a singly reinforced beam, if the permissible stress in concrete reaches earlier than that in steel, the beam section is called (A) Under-reinforced section (B) Over reinforced section (C) Economic section (D) Critical section

Last Answer : Answer: Option B

The section of a reinforced beam where most distant concrete fibre in compression and tension in steel attains permissible stresses simultaneously, is called (A) Balanced sectionB) Economic section (C) Critical section (D) All the above

Description : The section of a reinforced beam where most distant concrete fibre in compression and tension in steel attains permissible stresses simultaneously, is called (A) Balanced section B) Economic section (C) Critical section (D) All the above

Last Answer : Answer: Option D

A singly reinforced concrete beam of 25 cm width and 70 cm effective depth is provided with 18.75 cm2 steel. If the modular ratio (m) is 15, the depth of the neutral axis, is (A) 20 cm (B) 25 cm (C) 30 cm (D) 35 cm

Description : A singly reinforced concrete beam of 25 cm width and 70 cm effective depth is provided with 18.75 cm2 steel. If the modular ratio (m) is 15, the depth of the neutral axis, is (A) 20 cm (B) 25 cm (C) 30 cm (D) 35 cm

Last Answer : Answer: Option C

If the depth of actual neutral axis of a doubly reinforced beam (A) Is greater than the depth of critical neutral axis, the concrete attains its maximum stress earlier (B) Is less than the depth of critical neutral axis, the steel in the tensile zone attains its maximum stress earlier (C) Is equal to the depth of critical neutral axis; the concrete and steel attain their maximum stresses simultaneously (D) All the above

Description : If the depth of actual neutral axis of a doubly reinforced beam (A) Is greater than the depth of critical neutral axis, the concrete attains its maximum stress earlier (B) Is less ... critical neutral axis; the concrete and steel attain their maximum stresses simultaneously (D) All the above

Last Answer : Answer: Option D

The stresses developed in concrete and steel in reinforced concrete beam 25 cm width and 70 cm effective depth, are 62.5 kg/cm2 and 250 kg/cm2 respectively. If m = 15, the depth of its neutral axis is (A) 20 cm (B) 25 cm (C) 30 cm (D) 35 cm

Description : The stresses developed in concrete and steel in reinforced concrete beam 25 cm width and 70 cm effective depth, are 62.5 kg/cm2 and 250 kg/cm2 respectively. If m = 15, the depth of its neutral axis is (A) 20 cm (B) 25 cm (C) 30 cm (D) 35 cm

Last Answer : Answer: Option C

In a singly reinforced beam (A) Compression is borne entirely by concrete (B) Steel possesses initial stresses when embedded in concrete (C) Plane sections transverse to the centre line of the beam before bending remain plane after bending (D) Elastic moduli for concrete and steel have different values within the limits of deformation of the beam

Description : In a singly reinforced beam (A) Compression is borne entirely by concrete (B) Steel possesses initial stresses when embedded in concrete (C) Plane sections transverse to the centre line ... Elastic moduli for concrete and steel have different values within the limits of deformation of the beam

Last Answer : Answer: Option C

The allowable tensile stress in mild steel stirrups, reinforced cement concrete, is(A) 1400 kg/cm2(B) 190 kg/cm2(C) 260 kg/cm2(D) 230 kg/cm

Description : The allowable tensile stress in mild steel stirrups, reinforced cement concrete, is (A) 1400 kg/cm2 (B) 190 kg/cm2 (C) 260 kg/cm2 (D) 230 kg/cm

Last Answer : Answer: Option A

If the permissible stress in steel in tension is 140 N/mm², then the depth of neutral axis for a singly reinforced rectangular balanced section will be (A) 0.35 d (B) 0.40 d (C) 0.45 d (D) Dependent on grade of concrete also

Description : If the permissible stress in steel in tension is 140 N/mm², then the depth of neutral axis for a singly reinforced rectangular balanced section will be (A) 0.35 d (B) 0.40 d (C) 0.45 d (D) Dependent on grade of concrete also

Last Answer : Answer: Option B

In symmetrically reinforced sections, shrinkage stresses in concrete and steel are respectively (A) Compressive and tensile (B) Tensile and compressive (C) Both compressive (D) Both tensile

Description : In symmetrically reinforced sections, shrinkage stresses in concrete and steel are respectively (A) Compressive and tensile (B) Tensile and compressive (C) Both compressive (D) Both tensile

Last Answer : Answer: Option D

Expanded metal is (A) Manufactured from steel sheets (B) Used for reinforced concrete in road pavements (C) Measured in term of SWM (short way mesh) and LWM (long way mesh) (D) All the above

Description : Expanded metal is (A) Manufactured from steel sheets (B) Used for reinforced concrete in road pavements (C) Measured in term of SWM (short way mesh) and LWM (long way mesh) (D) All the above

Last Answer : Answer: Option D

Consider the following statements: Percentage of steel for balanced designed of a singly reinforced rectangular section by limit state method depends on (1) Characteristic strength of concrete (2) Yield strength of concrete (3) Modulus of elasticity of steel (4) Geometry of the section. Which of these statements are correct? (a) 2, 3 and 4 (b) 1, 3 and 4 (c) 1, 2 and 4 (d) 1, 2 and 3

Description : Consider the following statements: Percentage of steel for balanced designed of a singly reinforced rectangular section by limit state method depends on (1) Characteristic strength of concrete (2) Yield strength of concrete (3) Modulus of elasticity ... (b) 1, 3 and 4 (c) 1, 2 and 4 (d) 1, 2 and 3

Last Answer : 1,2,4

Regarding the working stress design of under reinforced concrete section, (a) The neutral axis depth will be greater than that of a balanced section. (b) The stress in steel intension will reach its maximum permissible value first. (c) The moment of resistance will be less than that of the balanced section. (d) The concrete on the tension side is also be considered for calculating the moment of resistance of the section.

Description : Regarding the working stress design of under reinforced concrete section, (a) The neutral axis depth will be greater than that of a balanced section. (b) The stress in steel intension will reach ... on the tension side is also be considered for calculating the moment of resistance of the section.

Last Answer : both b&c

For an over –reinforced (singly reinforced )rectangular reinforced concrete section (a) The lever arm will be less than that for a balanced section (b) The maximum stress developed by concrete will be equal to allowable stress in concrete (c) The maximum stress developed by steel will be equal to the allowable (d) All the above

Description : For an over -reinforced (singly reinforced )rectangular reinforced concrete section (a) The lever arm will be less than that for a balanced section (b) The maximum stress developed by concrete will be equal ... c) The maximum stress developed by steel will be equal to the allowable (d) All the above

Last Answer : (b) The maximum stress developed by concrete will be equal to allowable stress in concrete

In an over-reinforced section (a) Steel reinforcement is not fully stressed to its permissible value (b) Concrete is not fully stressed to its permissible value (c) Either (a) and (b) (d) Both (a) and (b)

Description : In an over-reinforced section (a) Steel reinforcement is not fully stressed to its permissible value (b) Concrete is not fully stressed to its permissible value (c) Either (a) and (b) (d) Both (a) and (b)

Last Answer : (a) Steel reinforcement is not fully stressed to its permissible value

In a singly reinforced beam, if the stress in concrete reaches its allowable limit later than the steel reaches, its permissible value, the beam section is said to be (a) Under-reinforced section (b) Over-reinforced section (c) Critical section (d) Balanced section

Description : In a singly reinforced beam, if the stress in concrete reaches its allowable limit later than the steel reaches, its permissible value, the beam section is said to be (a) Under-reinforced section (b) Over-reinforced section (c) Critical section (d) Balanced section

Last Answer : (b) Over-reinforced section

The moment of resistance of an under- reinforced section is computer on the basis of (a) Compressive force developed in concrete (b) Tensile force developed in steel (c) Both (a) & (b) (d) All the above

Description : The moment of resistance of an under- reinforced section is computer on the basis of (a) Compressive force developed in concrete (b) Tensile force developed in steel (c) Both (a) & (b) (d) All the above

Last Answer : (b) Tensile force developed in steel

The section in which concrete is not fully stressed to its permissible value when stress in steel reaches its maximum value is (a) Under-reinforced section (b) Over-reinforced section (c) Critical section (d) Balanced section

Description : The section in which concrete is not fully stressed to its permissible value when stress in steel reaches its maximum value is (a) Under-reinforced section (b) Over-reinforced section (c) Critical section (d) Balanced section

Last Answer : (a) Under-reinforced section

In a singly reinforced concrete beam, as the load increases. (a) Only concrete will resist tension (b) Only steel bars will resist tension. (c) Both concrete and steel will resist tension. (d) Both concrete and steel will resist compression.

Description : In a singly reinforced concrete beam, as the load increases. (a) Only concrete will resist tension (b) Only steel bars will resist tension. (c) Both concrete and steel will resist tension. (d) Both concrete and steel will resist compression.

Last Answer : (b) Only steel bars will resist tension.

In a reinforced concrete column, the cross –sectional area of steel bar is as and that of concrete ia AC; the equivalent area of the section n terms of concrete is equal to. (a) As+mAc (b) Ac+mAs (c) As-mAc (d) Ac-mAs

Description : In a reinforced concrete column, the cross –sectional area of steel bar is as and that of concrete ia AC; the equivalent area of the section n terms of concrete is equal to. (a) As+mAc (b) Ac+mAs (c) As-mAc (d) Ac-mAs

Last Answer : (b) Ac+mAs

In a singly reinforced concrete beam, if the load is vey small. (a) Only concrete will resist tension (b) Only steel bars will resist tension. (c) Both concrete & steel will resist tension. (d) Both concrete & steel will resist compression.

Description : In a singly reinforced concrete beam, if the load is vey small. (a) Only concrete will resist tension (b) Only steel bars will resist tension. (c) Both concrete & steel will resist tension. (d) Both concrete & steel will resist compression.

Last Answer : (c) Both concrete & steel will resist tension.

In the reinforced cement concrete structure, the steel reinforcement consists of . (a) Deformed bars (b) Cold twisted bars (c) Mildsteel and medium tensile steel bars (d) All of these

Description : In the reinforced cement concrete structure, the steel reinforcement consists of . (a) Deformed bars (b) Cold twisted bars (c) Mildsteel and medium tensile steel bars (d) All of these

Last Answer : (d) All of these

In a singly reinforced beam, if the permissible stress in steel reaches earlier than that of concrete, the beam section as called [ A ] Under reinforced section [ B ] Over reinforced section [ C ] Balanced section [ D ] Critical section

Description : In a singly reinforced beam, if the permissible stress in steel reaches earlier than that of concrete, the beam section as called [ A ] Under reinforced section [ B ] Over reinforced section [ C ] Balanced section [ D ] Critical section

Last Answer : [ A ] Under reinforced section

In a Singly reinforced beam, if the permissible stress in concrete reaches earlier than that in steel, the beam section is called [ A ] Under reinforced section [ B ] Over reinforced section [ C ] Balanced section [ D ] Critical section

Description : In a Singly reinforced beam, if the permissible stress in concrete reaches earlier than that in steel, the beam section is called [ A ] Under reinforced section [ B ] Over reinforced section [ C ] Balanced section [ D ] Critical section

Last Answer : [ B ] Over reinforced section

The section of a reinforced beam where most distant concrete fiber in compression and tension in steel attains permissible stresses simultaneously is called (i)Balanced section (ii)Economic section (iii)Critical section [ A ] i [ B ] i and ii [ C ] i and iii [ D ] i, ii and iii

Description : The section of a reinforced beam where most distant concrete fiber in compression and tension in steel attains permissible stresses simultaneously is called (i)Balanced section (ii)Economic section (iii)Critical section [ A ] i [ B ] i and ii [ C ] i and iii [ D ] i, ii and iii

Last Answer : [ D ] i, ii and iii

Pick out the wrong statement. (A) Seam welding, projection welding & spot welding are the classification of electrical resistance welding (B) Electrode tip in spot welding is of copper and the tip diameter should be equal to t (where, t = plate thickness to be welded) (C) In spot welding, two pieces to be joined are overlapped and placed between two electrodes (D) Mild steel sheet cannot be spot welded

Description : Pick out the wrong statement. (A) Seam welding, projection welding & spot welding are the classification of electrical resistance welding (B) Electrode tip in spot welding is of copper and the ... joined are overlapped and placed between two electrodes (D) Mild steel sheet cannot be spot welded

Last Answer : (D) Mild steel sheet cannot be spot welded

Select the incorrect statement from the following [ A ] Reinforcing bars in a column should not be less than 12 mm in diameter [ B ] The number of longitudinal bars in a circular column should not exceed four [ C ] The minimum percentage of longitudinal steel in columns should be 0.8% [ D ] None of the above

Description : Select the incorrect statement from the following [ A ] Reinforcing bars in a column should not be less than 12 mm in diameter [ B ] The number of longitudinal bars in a circular column should not ... The minimum percentage of longitudinal steel in columns should be 0.8% [ D ] None of the above

Last Answer : [ B ] The number of longitudinal bars in a circular column should not exceed four

Depth of lean concrete bed placed at the bottom of a wall footing, is kept (A) 10 cm (B) 15 cm (C) Equal to its projection beyond wall base (D) Less than its projection beyond wall base

Description : Depth of lean concrete bed placed at the bottom of a wall footing, is kept (A) 10 cm (B) 15 cm (C) Equal to its projection beyond wall base (D) Less than its projection beyond wall base

Last Answer : Answer: Option C

An intermediate T-beam reinforced with two layers of tensile steel with clear cover 13 cm encasted with the floor of a hall 12 metres by 7 metres, is spaced at 3 metres from adjoining beams and if the width of the beam is 20 cm, the breadth of the flange is (A) 300 cm (B) 233 cm (C) 176 cm (D) 236 cm

Description : An intermediate T-beam reinforced with two layers of tensile steel with clear cover 13 cm encasted with the floor of a hall 12 metres by 7 metres, is spaced at 3 metres from adjoining beams and if the width of the beam is ... breadth of the flange is (A) 300 cm (B) 233 cm (C) 176 cm (D) 236 cm

Last Answer : Answer: Option C

The film thickness for laminar film condensation on vertical surface __________ from top to bottom. (A) Cumulatively increases (B) Cumulatively decreases (C) Remain constant (D) And the surface conductance increase

Description : The film thickness for laminar film condensation on vertical surface __________ from top to bottom. (A) Cumulatively increases (B) Cumulatively decreases (C) Remain constant (D) And the surface conductance increase

Last Answer : (A) Cumulatively increases

In a cantilever retaining wall without a heel slab (A) Thickness of the stem is kept same throughout (B) Base slab is made 10 cm thicker than the stem (C) Width of the base slab is kept 0.7 time the total height of the wall (D) All the above

Description : In a cantilever retaining wall without a heel slab (A) Thickness of the stem is kept same throughout (B) Base slab is made 10 cm thicker than the stem (C) Width of the base slab is kept 0.7 time the total height of the wall (D) All the above

Last Answer : Answer: Option D

In a T-beam, the vertical distance between the bottom of the flange and the centre of the tensile reinforcement is (a) Breadth of flange (b) Thickness of flange (c) Breadth of slab (d) Depth of rib

Description : In a T-beam, the vertical distance between the bottom of the flange and the centre of the tensile reinforcement is (a) Breadth of flange (b) Thickness of flange (c) Breadth of slab (d) Depth of rib

Last Answer : (d) Depth of rib

Maximum deflection of a (A) Cantilever beam carrying a concentrated load W at its free end is WL3 /3EI (B) Simply supported beam carrying a concentrated load W at mid-span is WL3 /48EI (C) Cantilever beam, carrying a uniformly distributed load over span is WL3 /8EI (D) All the above

Description : Maximum deflection of a (A) Cantilever beam carrying a concentrated load W at its free end is WL3 /3EI (B) Simply supported beam carrying a concentrated load W at mid-span is WL3 /48EI (C) Cantilever beam, carrying a uniformly distributed load over span is WL3 /8EI (D) All the above

Last Answer : (D) All the above

Design of R.C.C. cantilever beams, is based on the resultant force at (A) Fixed end (B) Free end (C) Mid span (D) Mid span and fixed support

Description : Design of R.C.C. cantilever beams, is based on the resultant force at (A) Fixed end (B) Free end (C) Mid span (D) Mid span and fixed support

Last Answer : Answer: Option A

Find the correct statement from the followings. (a) For a cantilever slab, the ratio of span to overall depth should not 12. (b) One way slab which carry uniformly distributed load should be designed to resist a sagging bending moment near mid-span. (c) When the slab is built into a brick or masonry wall the slab should be designed to resist a hogging moment at the face of the support. (d) All of the above.

Description : Find the correct statement from the followings. (a) For a cantilever slab, the ratio of span to overall depth should not 12. (b) One way slab which carry uniformly distributed load should be designed to ... be designed to resist a hogging moment at the face of the support. (d) All of the above.

Last Answer : (d) All of the above.