Using a combination of uniselectors and two motion selectors, draw a schematic of thousand line exchange and explain its working.

1 Answer

Answer :

The schematic diagram for such an exchange is given in Fig. Each subscriber is connected to a single rotary pre-selector switch at the exchange, the outputs from  this switch being connected to a bank of two-motion switches known as ‘group selectors’. The out-puts from the pre-selector switches of a whole group of subscribers are connected together in parallel as that group of subscribers share a single bank of group selectors. When a subscriber lifts his telephone, the cradle switch causes a circuit to be completed back to the telephone exchange, signaling that the subscriber wishes to make a call. This causes the pre-selector switch to step around until it finds a free group selector. The pre-selector switch then stops in this position and the group selector is ‘seized’ by the subscriber wishing to make a call.

image

In a 1000 line exchange, each subscriber has a 3 digit identification number starting from 000 to 999. On seizing the group selector, the subscriber dials his first digit and the selector switch moves up to the appropriate row on the switch contact array. Each final selector has the possibility of connection to 100 lines. The 1000 lines are therefore divided into 10 groups of 100 each, the group being identified by the first digit in the subscriber’s number. The vertical motion of the group selector therefore selects a final selector in the group associated with the first digit dialed. Each individual row of contacts, or levels, of the group selector is connected to a bank of final selectors associated with a particular group of 100 line numbers. Having dialed the first digit to select the appropriate group, the group selector arm then automatically rotates in the vertical direction until it finds a free final selector. In the final selector, both directions of motion are under the control of the subscriber’s dial and, after dialing two further digits, connection is established, providing the called subscriber’s to answer his telephone.  

Related questions

Description : In a hundred-line exchange 24 two-motion selectors are used. Draw the schematic you suggest for this exchange and explain its working. How many simultaneous calls can be made during peak hour in this exchange?

Last Answer : The desired schematic for 100 lines exchange with 24 two motion selectors is shown in Fig.   In the case, 24 simultaneous calls can be put through the switch . Typically, a 24- ... selector. At the next step, the two-motion selector responds to the dial pulses for appropriate connection.

Description : What are the different ways of designing 100 line exchange using uni selector and two motion selectors? Show at least three variations. Which is the best option?

Last Answer : Here three different designing methods for 100 line exchange are discussed: Design 1: Here, Strowger switching system is designed using one two-motion selector for each subscriber. A ... only under certain specific traffic conditions and generally lead to higher blocking probabilities.  

Description : Explain the CCITT hierarchical structure of switching and routing using block schematic.

Last Answer : Hierarchical network are capable of handing heavy traffic where required, and at the same time use minimal number of trunk groups. A 5-level switching hierarchy is recommended by CCITT as ... A strictly hierarchical network suffers from serious drawback i.e. its poor fault tolerance future.

Description : How does a touch tone receiver differs from pulsed dial receiver? Explain with schematic.

Last Answer : Pulse dialing: 1. Generated through make and break contact. 2. DC Current pulse is generated. 3. Each number is separated by a short pause to prevent overlapping. 4. Codes ... dialing pulse is not misinterpreted as the phone being returned to its on-hook (idle) condition.   

Description : Write short notes (i)Telephone hand set and it’s working. (ii) CPU based exchange

Last Answer : (i) A standard telephone set is comprised of a transmitter, a receiver, and electrical network for equalization, associated circuitry to control side tone levels and to regulate signal power, ... commands are designed to be of variable length necessitating the use of an end-of-command symbol  

Description : Explain crossbar exchange, with all call processing steps and diagrams

Last Answer : The basic idea of crossbar switching is to provide a matrix of n x m sets of contacts with only n + m activators or less to select one of the n x m sets of contacts. This form of ... a contact is established at the cross point 6 such that the subscriber B is connected to the subscriber C. 

Description : What do you mean by numbering and addressing? Draw the ISDN address structure and explain how the addressing works?

Last Answer :  Numbering and Addressing: In telephone and data networks, the end equipments are more often single units than multiple devices units like PABX or LAN. Historically, a telephone, a computer, or a ... as reference point may also be addressed by using direct inward dialing (DID) feature.  

Description : Draw a centralized SPC organization and explain how it works under load sharing operation.

Last Answer : In centralized control, all the control equipment is replaced by a single processor which must be quite powerful. It must be capable of processing 10 to 100 calls per second, depending on the ... both the processors are active simultaneously and share the load and the resources dynamically.  

Description : Name the switching schemes used in a digital exchange. How call processing takes place?

Last Answer : The different switching systems used are: 1. Strowger Switching System 2. Cross bar Switching. 3. Electronic Switching System Basic Call Procedure: Fig. Shows a simplification ... machine detects an open circuit on that loop and then drops the connections through the switch.  

Description : Trunks are the lines that run between (A) Subscribers and exchange (B) Switching system and power plant (C) Local area network (D) Switching stations

Last Answer : (D) Switching stations

Description : Signalling transfer point (STP) exist in (A) Strowger exchange (B) SS7 (C) Local area network (D) PABX

Last Answer : (B) SS7

Description : Engaged tone is generated in the: (A) Telephone instrument of calling subscriber (B) Telephone instrument of called subscriber (C) Exchange (D) Repeater

Last Answer : (C) Exchange

Description : Trunks are the lines that run between (A) subscribers and exchange (B) switching system and power plant (C) Local Area Network (D) switching systems

Last Answer : (B) switching system and power plant

Description : SPC is used for (A) Carrying Exchange Control Functions (B) Carrying Subscriber Control Functions (C) Exchange Hardware (D) Signalling Purpose

Last Answer : (A) Carrying Exchange Control Functions

Description : A star connected intermediate exchange is known as a (A) Repeater exchange (B) Hub exchange (C) Private branch exchange (D) Tandem exchange

Last Answer : (B) Hub exchange

Description : Trunks are the lines that run between (A) Subscribers and exchange (B) switching system and power plant (C) Local area network. (D) Switching stations.

Last Answer : (D) Switching stations.

Description : What is centralized SPC, what are its modes of operation; explain the working of any one of these?

Last Answer : In centralized control, all the control equipment is replaced by a single processor which must be quite powerful. It must be capable of processing 10 to 100 calls per second, depending on ... The shared secondary storage need not be duplicated and simple unit level redundancy would suffice.  

Description : Explain the working of broad band ISDN.

Last Answer :  BISDN Configuration: Fig. shows how access to the BISDN network is accomplished. Each peripheral device is interfaced to the access node of a BISDN network through a broadband distant ... consequently, have higher transmission rates and offer more channel handling capacity than ISDN systems.  

Description : (a) Draw a schematic representation of transport and exchange of oxygen and carbon dioxide during transportation of blood in human beings and label on it: Lung capillaries, Pulmonary artery to ... the advantage of separate channels in mammals and birds for oxygenated and deoxygenated blood? -Biology

Last Answer : (a) A schematic representation of transportation and exchange of oxygen and carbon dioxide during transportation of blood in human beings (b) It is necessary to separate oxygenated and deoxygenated ... . The separation of oxygenated and deoxygenated blood provides high oxygen supply to the organs.

Description : Draw schematic diagram of welding transformer showing constructional features of a welding transformer. Also explain its working.

Last Answer : Constructional features of welding transformer: Working of welding transformer: i) It is a step down transformer that reduces the voltage from the source voltage to a voltage desired according to the demands of ... 230 V, 415 V Secondary voltage - 40 to 60 V Secondary current - 200 to 600 A

Description : Echo suppressor is detrimental to full duplex operation because (A) It disables one of the two pairs in a four-wire trunk line when a signal is detected on the other pair. (B) It enables one of the ... It activates both the pairs of a four-wire trunk line. (D) It is independent of line conditions.

Last Answer : (A) It disables one of the two pairs in a four-wire trunk line when a signal is detected on the other pair.

Description : In step by step switching line finders are connected to the (A) Calling subscriber. (B) Switching network. (C) Called subscriber. (D) Between exchanges.

Last Answer : (A) Calling subscriber.

Description : Call request signal is: (A) Seize signal (B) Idle state signal (C) Line identification signal (D) Called subscriber alert signal

Last Answer : (A) Seize signal

Description : Distortion caused on telephone line by an adjacent one is called (A) Cross Fire (B) Inductive Disturbance (C) Cross Talk (D) None of these

Last Answer : (C) Cross Talk

Description : The final selector is connected to the (A) calling subscriber. (B) switching network. (C) called subscriber. (D) line finder.

Last Answer : (C) called subscriber

Description : How speech is transmitted in a digital switching environment using PCM/TDM?

Last Answer : A digital carrier system is a communications system that uses digital pulses rather than analogue signals to encode information. Fig shows the block diagram for a digital carrier system. This digital ... to maintain frame and sample synchronization between the TDM transmitter and receiver. 

Description : Using ______ARQ, a sending modem must wait for a return ACK for each sent block before sending the next block. (A) discrete (B) efficient (C) continuous (D) delivered

Last Answer : (A) discrete

Description : A large numbers of computers in a wide geographical area can be efficiently connected using (A) twisted pair lines (B) coaxial cables (C) Communication satellites (D) all of the above

Last Answer : (D) all of the above

Description : What is time multiplexed space switching? With a neat diagram explain its operation.

Last Answer : Time division switches where an inlet or an outlet corresponded to a single subscriber line with one speech sample appearing every 125 µs on the line. Such switches are used in local exchanges. We now ... / Mt , Where t is the switching time including memory access time per inlet-outlet pair.  

Description : Through two block diagrams explain the difference between Space division and time division switching.

Last Answer :  Space and Time Switching: Space Switches: Connections can be made between incoming and outgoing PCM highways by means of a cross point matrix of the form shown in Fig. However, different channels of ... of the speech store, whose contents are read out and sent over the outgoing highway.  

Description : Explain the process of inter-register signalling.

Last Answer : Registers are used in common control exchanges to store and analyze routing data. They are provided on a common basis is a single register provides routing data for a number of speech circuits. Once a call ... it is released and the originating register signals to the next register.

Description : Explain FDM and show how CCITT standards help in building the base band?

Last Answer : Frequency Division Multiplexing: It is the process of combining several information channels by shifting their signals to different frequency groups within the spectrum so that they can be transmitted simultaneously ... of 24 channels were assembled together in one stage of modulation.     

Description : Explain topology method used in LAN technology in detail.

Last Answer : LAN Topologies: Network topology is a physical schematic which shows interconnection of the many users. There are four basic topologies as under: (i) Direct Connection or one to all topology ( ... temporarily, inserting the new node and then reestablishing the complete ring path.

Description : Find the total number of link L having five entities? Explain differences between folded and non-folded network.

Last Answer : Folded network: When all the inlets/outlets are connected to the subscriber lines, the logical connection appears as shown in Fig. In this case, the output lines are folded back to the input ... non-folded network to be non-blocking, the network should support N simultaneous switching paths.  

Description : Explain simple telephone communication system with circuit and equation of current flow in microphone?

Last Answer : Simple Telephone Communication: In the simplest form of a telephone circuit, there is one way communication involving two entities, one receiving (listening) and the other transmitting (talking).   ... carrier wave in AM system. The quantity m is equivalent to the modulation index in AM. 

Description : What is a Modem? What is the need of MODEM in data communication? Explain at least one modulation technique used for high speed modems.

Last Answer : Modems are essentially used to interface digital circuits to transmit information on analogue channels like telephone systems. Modem (from modulator-demodulator) is a device that modulates an analogue carrier ... caused by the lines makes the detection even harder than amplitude modulation.   

Description : What are different control function categories, explain, how they help in signalling and control.

Last Answer : In some switching systems, the control subsystem may be an integral part of the switching network itself. Such system is known as direct control switching systems. Those systems in which the control ... may be carried out at the level of the common control unit or the switching network.  

Description : Explain the architecture of SS7 and compare with seven-layer OSI architecture.

Last Answer : A block schematic diagram of the CCITT no. 7 signaling system is shown in fig. Signal messages are passed from the central processor of the sending exchange to the CCS system. This consists of the microprocessor based ... part (TUE), the data user part(DUP) and the (ISDN) user part (ISDN-UP).  

Description : Explain the terms. (i) Register marker. (ii) Conditional selection.

Last Answer : (i) Register marker: Strowger selectors perform counting and searching. However, the crossbar switch has no intelligence'. Something external to the switch must decide which magnets to operate. This is ... are found to be free does it operate the switches. This is called Conditional Selection. 

Description : Explain what is DTMF signalling.

Last Answer : Dual Tone Multi Frequency (DTMF) was first introduced in 1963 with 10 buttons in Western Electric 1500 -type telephones. DTMF was originally called TouchTone. DTMF is a more efficient means than ... ). The letters were originally used to identify one local telephone exchange from another.  

Description : Explain the following terms: progressive control, common control and stored program control.

Last Answer : (i) Progressive Control: Step by step system is an example of progressive control. The connection is set up in stages, in response to the digits dialed and each step in setting up the ... some of the features that have become possible due to the application of SPC to telephone switching  

Description : Explain the basic architecture of digital switching systems. Explain in detail companding.

Last Answer : A simple N X N time division space switch is shown in Fig. The switch can be represented in an equivalence form as a two-stage network with N X 1 and 1 X N switching matrices for the first and ... = Parameter used to define the amount of compression  Vout = Compressed output voltage. 

Description : Classify data networks. Explain with the help of Nyquist theorem, the data rate limitations in PSTN’s. Give an account of modems used in data transfer. Explain their importance and list some of the V-series recommendations.

Last Answer : Classifications of Data Network:  Data Networks are classified according to their geographical coverage: Wide area networks (WANs) Metropolitan area networks(MANs) Local area ...  V.53 Limits for the maintenance of telephone type circuits used for data transmission. 

Description : What layers are covered under end to end layer connectivity? Explain briefly the function of each one of them.

Last Answer : The layers 4-7 of ISO-OSI reference model communicate with peer entities in the end systems. There is no communication with entities in the intermediate systems. In this sense, layers 4-7 are often ... 6. Editors and terminal support services 7. Telematic services like videotext. 

Description : What is meant by common control? Explain all the categories that are served by Common Control switching.

Last Answer : In some switching systems, the control subsystem may be an integral part of the switching network itself. Such system is known as direct control switching systems. Those systems in which the control ... may be carried out at the level of the common control unit or the switching network.  

Description : What are the different types of distributing frames used in exchanges? Explain their importance.

Last Answer : The different distribution frames used in exchange are shown in figure. Every subscriber in a telephone network is connected generally to the nearest switching office by means of a dedicated pair of ... . The subscriber cable pairs emanating from the exchange are also terminated on the MDF.  

Description : What are the different tones used in strowger telephony? Explain with the help of waveforms and the timings.

Last Answer : Dial Tone: This tone is used to indicate that the exchange is ready to accept dialed digits from the subscriber. The subscriber should start dialing only after hearing the dialing tone. Sometimes, ... as the call progresses through different exchanges. Fig. shows a routing tone pattern.   

Description : Explain the terms topology and access methods used in LANs. Discuss the CSMA/CD and CSMA/CA protocols.

Last Answer : (i) LAN topologies: Network topology is a physical schematic which shows interconnection of the many users. There are four basic topologies as under:  (a) Direct Connection or one to all ... it is free, the station transmits, and waits for an acknowledgment signal that the packet was received

Description : What are the end-to-end layers of OSI structure? Explain the transport layer in detail.

Last Answer : The layers 4-7 of ISO-OSI reference model communicate with peer entities in the end systems. There is no communication with entities in the intermediate systems. In this sense, ... tracking, connection flow control, sequencing of data, error checking, and application addressing and identification.

Description : What are wired and wireless transmission systems? Explain the mechanisms of propagation of radio communication.

Last Answer :  Transmission Systems: Modern long distance transmission systems can be placed under three broad categories: 1. Radio Systems 2. Coaxial cable systems 3. Optical fibre systems  ... microwave communication limited by horizon. 3. Troposphere scatter communication 4. Satellite communication.