Description : Which of the referenced waveshapes would appear at point 'Y' in the circuit shown in the illustration? EL-0085 A. A B. B C. C D. D
Last Answer : Answer: D
Description : Which of the referenced waveshapes would appear at point 'Z' in the circuit shown in the illustration? EL-0085 A. A B. B C. C D. D
Last Answer : Answer: C
Description : Which of the referenced waveshapes would appear at point 'X' of the circuit shown in the illustration? EL-0085 A. A B. B C. C D. D
Last Answer : Answer: A
Description : What is the direction of current through the load resistor in the circuit shown in the illustration? EL-0085 A. Always from point 'Z' to the grounded end. B. Always from the grounded end to ... on the instantaneous polarity at point 'W'. D. It cannot be determined without a directional ammeter.
Last Answer : Answer: B
Description : What is the polarity of voltage at point 'Z' in the circuit shown in the illustration? EL-0085 A. It will always be positive. B. It will always be negative. C. It depends on the instantaneous polarity at point 'W'. D. It cannot be determined without a voltmeter.
Description : Assuming a standard 60 Hz. input to the circuit shown in the illustration, the ripple frequency would be ____________. EL-0085 A. 30 Hz B. 60 Hz C. 90 Hz D. 120 Hz
Description : The component labeled 'CR1' in the circuit shown in the illustration __________________. EL-0085 A. varies its anode/cathode polarity depending on 'RL' current B. rectifies the varying voltage from the ... reactance to smooth ripple D. establishes a constant reference voltage for the base of 'Q1'
Description : The fluctuation of voltages in figure 'A' and 'D' of the circuit shown in the illustration is called ____________. EL-0085 A. wave B. ripple C. roll D. swell
Description : Section II of the circuit shown in the illustration is the ____________. EL-0085 A. voltage regulator B. filter C. rectifier D. voltage transformer
Description : Section IV of the circuit shown in the illustration is the _____________. EL-0085 A. voltage regulator B. filter C. rectifier D. voltage transformer
Description : Which section of the circuit shown in the illustration changes AC to DC? EL-0085 A. I B. II C. III D. IV
Description : Section III of the circuit shown in the illustration is a _____________. EL-0085 A. voltage regulator B. filter C. rectifier D. voltage transformer
Description : Which section of the circuit shown in the illustration smooths out highest degree of pulsations? EL-0085 A. I B. II C. III D. IV
Description : The circuit shown in the illustration represents a/an ____________. EL-0085 A. operational amplifier B. Wheatstone bridge C. magnetic amplifier D. power supply
Description : Component 'CR1' shown in the illustration is called a/an _______________. EL-0085 A. avalanche diode B. Zener diode C. breakdown diode D. all of the above
Description : The turns ratio of transformer 'A' shown in the illustration is four to one and all taps are evenly spaced. If 120 volts were applied to terminals 'H1' and 'H3', what would appear at 'X1' and 'X2'? EL-0082 A. 15 volts B. 30 volts C. 480 volts D. 960 volts
Description : The turns ratio of device 'A' shown in the illustration is four to one and all taps are evenly spaced. If 120 volts were applied to terminals 'H1' and 'H3', what would appear at 'X1' and 'X2'? EL-0082 A. 15 volts B. 30 volts C. 480 volts D. 960 volts
Description : The turns ratio of device 'A' shown in the illustration is four to one and all taps are equally spaced. If 440 volts were applied between 'H1' and 'H4', what would appear across 'X1' and 'X4'? EL-0082 A. 110 volts B. 220 volts C. 440 volts D. 1760 volts
Description : The winch shown in the illustration will not operate in any speed in the lowering direction and at an abnormal speed in 'first point hoist'. The possible cause is that _______________. EL-0102 A. ... '1M' in the power circuit are badly corroded D. master switch contacts 'MS6' have weak springs
Description : The purpose of 'R6' in the winch circuit shown in the illustration is to _______________. EL-0102 A. maintain dry conditions within the winch brake box B. keep the series field current at ... to assist the winch in stopping D. limit the armature current during lowering operation with heavy loads
Description : The purpose of the 'heater resistors' for the winch circuit shown in the illustration is to _______________. EL-0102 A. limit the current in the heater circuit B. dispel moisture in the ' ... panel C. keep the winch brake housing below the dew point D. maintain winch motor operating temperature
Description : The purpose of the bias winding in figure 'B' shown in the illustration is for ____________. EL-0091 A. changing the direction of current in the control winding B. setting the operating point of the ... use of either AC or DC in the load circuit D. changing the direction of current through the load
Description : Which section of the circuit is responsible for maintaining a nearly constant voltage for all loads within its operating range? EL-0085 A. I B. II C. III D. IV
Description : In the illustrated circuit, section II is considered to be a _______. EL-0085 A. full wave rectifier B. half wave rectifier C. quarter wave rectifier D. short wave rectifier
Description : In which section of the 24 VDC power supply circuit illustrated, does the greatest change in voltage level take place when fed from ships power. EL-0085 A. I B. II C. III D. IV
Description : In the schematic of the electrical circuit shown in the illustration, what is the value of the total capacitance, when compared to the value of equal individual capacitors? EL-0038 A. Equal B. Half C. Double D. Squared
Description : What type of logic circuit is indicated by the truth table shown in the illustration? EL-0072 A. OR B. AND C. NOR D. NAND
Description : If a voltage tester is being used to check for defective fuses in the circuit, shown in the illustration, which of the readings will indicate that fuse #2 is open? EL-0062 A. C-B full voltage B. A-D full voltage C. A-D no voltage D. C-B no voltage
Description : The wiring diagram for the motor starting circuit shown in the illustration indicates ______________. EL-0007 A. resistance starting B. reduced voltage starting C. low voltage protection D. low voltage release
Description : The electrical diagram shown in the illustration is used to depict a/an ____________. EL-0015 A. resistance circuit B. inductive circuit C. stepdown circuit D. capacitive circuit
Description : The electrical schematic shown in the illustration indicates the lighting feeder circuit is _____________. EL-0014 A. three phase, 450 volt, and 60 cycle B. three phase, 120 volt, and 60 cycle C. single phase, 120 volt, and 60 cycle D. not specified
Description : In the lighting distribution circuit shown in the illustration, if all switches are closed and fuse 'F2' were to open, all lights on branches ____________. EL-0013 A. '1', '2', and '3' would go out B. '1' ... and '3' would burn dimly D. '1' and '3' would go out, while branch '2' would remain lit
Description : The schematic diagram shown in the illustration uses symbol 'A' to represent a/an _________. EL-0011 A. non-renewable fuse link B. circuit breaker coil C. overload relay coil D. thermal overload heater
Description : When an operating motor is connected to the controller shown in the illustration, the a path of current flow through the circuit is ____________. EL-0010 A. 'L1', stop button, start button, coil 'CR', 'L2' B. 'L1' ... L2' D. 'L1', stop button, start button, 'CR' contact, 'M' contact, 'CR' coil, 'L2'
Description : If the circuit shown in the illustration were energized and operating properly, which of the devices listed would be open? EL-0007 A. The stop push-button B. The start push-button C. Contact 'Ma' D. Contact 'OL1'
Description : Which of the following actions must be carried out prior to closing the alternator circuit breaker according to the graph shown in the illustration? EL-0002 A. Increase the alternator voltage. B. Decrease the line voltage. C. Increase the line voltage. D. Decrease the line frequency.
Description : As shown in the illustration, 'B' is a ____________. EL-0058 A. single-pole, double-throw switch B. double-pole, single-throw switch C. double-pole, double-throw switch D. circuit breaker
Description : In electric circuit schematics, a transformer is represented by which of the symbols shown in the illustration? EL-0059 A. A B. B C. C D. D
Description : Sound powered telephone units 'I', 'II', and 'III' of the circuit shown in the illustration are for 'station numbers' _____________. EL-0093 A. 2, 4 and 6 B. 1, 2 and 3 C. 3, 5 and 8 D. 1, 2 and 6
Description : When replacing component 'B' of the circuit shown in the illustration, it is important to know that ____________. EL-0081 A. it is polarity sensitive and must be inserted as indicated on its ... provide the capacitor's initial charge D. it must match the circuit voltage and component 'C' wattage
Description : As shown in the illustration if the applied voltage is 12 VDC, the resistance of R1 is 10 ohms, and R2 is 10 ohms what is the total power consumed by the circuit? EL-0036 A. 3.6 watts B. 72 watts C. 7.2 watts D. 36 watts
Description : As shown in the illustration if the applied voltage is 12 VDC, the resistance of R1 is 10 ohms, and R2 is 10 ohms what is the total current in the circuit? EL-0036 A. 0.6 amp B. 0.833 amp C. 1.2 amps D. 2.4 amps
Description : As shown in the illustration if the applied voltage is 12 VDC, the resistance of R1 is 110 ohms, and R2 is 10 kohms what is the total power consumed by the circuit? EL-0036 A. 3.6 watts B. 72 watts C. .0011286 watts D. .014243 watts
Description : The proper method of connecting an ammeter in a circuit is demonstrated by which of the diagrams shown in the illustration? EL-0041 A. A B. B C. C D. All of the above
Description : What is the value of the capacitor in the astern valve position circuit shown in the illustration? EL-0099 A. 100 kFarad B. 0.5 microfarad C. 0.5 millifarad D. 50 kFarad
Description : Peripheral components for the operation of the astern valve position amplifier circuit shown in the illustration are _____________. EL-0099 A. resistors B. operated on +28 volts D.C. C. located on a separate circuit card D. all of the above
Description : The signal to the circuit on card 'A0AA2' at coordinate '29Q' shown in the illustration is on the ____________. EL-0099 A. non-inverting input at pin '20' B. inverting input at pin '16' C. non-inverting input at pin '14' D. inverting input at pin '46'
Description : The winch shown in the illustration operates in any of the positions with the master switch in the 'lower' direction, but will not 'hoist' in any of the master switch hoist positions. Which of the listed faults ... '2M' in the power circuit may be badly corroded. D. Series relay 'FR' may be open.
Description : What type of circuit is on card 'A0AA2' at coordinate '29Q' shown in the illustration? EL-0099 A. Operational amplifier B. Digital logic inverter C. Square wave pulse generator D. Binary counter
Description : In order to prevent the winch shown in the illustration from turning while troubleshooting the controller circuit, _________________. EL-0102 A. set the dynamic brake by clamping contact 'DB' closed B. set the ... at 'B1' and 'B2' D. open the test link preventing current flow to the armature