Description : The electrical supply applied to the anodes shown in the illustration is _____________. EL-0090 A. low voltage, high current DC B. low voltage, high current AC C. high voltage, low current DC D. high voltage, low current AC
Last Answer : Answer: A
Description : The voltage at the reference electrode of the circuit shown in the illustration is applied to the input of a/an ______________. EL-0090 A. class A detector whose output drives an ... drives an 2-stage isolation transformer D. magnetic amplifier whose output controls a saturable reactor
Last Answer : Answer: D
Description : When the circuit shown in the illustration is operating correctly, the voltage at the reference electrode will be kept in the optimum range of ____________. EL-0090 A. 0.01 - 0.05 volt B. 0.80 - 0.85 volt C. 35 - 60 volts D. 100 - 115 volts
Last Answer : Answer: B
Description : The circuit shown in the illustration represents a ________. EL-0090 A. battery charging circuit B. synchronous exciter C. depth sounding unit D. cathodic protection system
Description : What is the purpose of each of the 'signal conditioners' (6000F085 / AH170 / F125) shown in the illustration? EL-0094 A. Convert the varying signal from its particular sensor and deliver a ... the 'setpoint module' in order to keep the pressure or temperature at its sensor at set limits.
Description : As shown in the illustration, what maintenance would be required of the circuit components? EL-0058 A. Change out both 'C' units monthly. B. Clean the glass surrounding 'E1' & 'E2' as needed. C. File ... upper end of 'G' every six months. D. Take megger readings on 'E1' & 'E2' windings quarterly.
Description : Considering the function of the circuit shown in the illustration, what is the purpose of supplying the thrust lever potentiometers with both (+) and (-) 15 volts? EL-0095 A. To select which ... alternate voltage supply if the other fails. D. So as to automatically select the position of Relay #
Description : The circuit shown in the illustration represents a/an ____________. EL-0085 A. operational amplifier B. Wheatstone bridge C. magnetic amplifier D. power supply
Description : Figure 'D' of the diagram shown in the illustration has a turns ratio of four to one. If a three-phase 440 volt supply is connected to terminals 'A-B-C', what voltage should develop across terminals 'a-b-c'? EL-0084 A. 64 volts B. 110 volts C. 190 volts D. 762 volts
Description : Figure 'C' of the diagram shown in the illustration has a turns ratio of four to one. If a three-phase 440 volt supply is connected to terminals 'A-B-C', what voltage should develop across terminals 'a-b-c'? EL-0084 A. 64 volts B. 110 volts C. 190 volts D. 762 volts
Last Answer : Answer: C
Description : Figure 'B' of the diagram shown in the illustration has a turns ratio of four to one. If a three-phase 440 volt supply is connected to terminals 'A-B-C', what voltage should develop across terminals 'a-b-c'? EL-0084 A. 64 volts B. 110 volts C. 190 volts D. 762 volts
Description : Figure 'A' of the diagram shown in the illustration has a turns ratio of four to one. If a three-phase 440 volt supply is connected to terminals 'A-B-C', what voltage should develop across terminals 'a-b-c'? EL-0084 A. 64 volts B. 110 volts C. 190 volts D. 762 volts
Description : Figure 'A' of the diagram shown in the illustration represents a ______________. EL-0092 A. differential transformer B. saturable reactor C. synchro system D. magnetic amplifier
Description : Figure 'B' shown in the illustration represents a/an ____________. EL-0091 A. magnetic amplifier B. Scott-T transformer C. saturable-core reactor D. oil-filled toroid
Description : Figure 'A' shown in the illustration represents a/an _______________. EL-0091 A. magnetic amplifier B. Scott-T transformer C. saturable-core reactor D. oil-filled toroid
Description : How many different D.C. voltages are required to operate the circuit shown in the illustration? EL-0094 A. Two B. Three C. Four D. Five
Description : The reading at 'M' on the megger scale shown in the illustration, is __________. EL-0044 A. 7.1 meg ohms B. .71 meg ohms C. 71 meg ohms D. 200,000,000 ohms
Description : If coils 'R1-R2-R3' at the receiver of figure 'B' shown in the illustration turned opposite of those in the transmitter by design, what corrective action should be taken? EL-0092 A. Reverse the 60 Hz supply ... is needed. C. Interchange leads 'R1' and 'R3'. D. Interchange leads 'R2' and 'R3'.
Description : If coil 'R1-R2' at the receiver of figure 'A' shown in the illustration were in 180 degree error with respect to that of the transmitter, what corrective action should be taken? EL-0092 A. No action is ... and 'R2'. C. Interchange connections 'S1' and 'S2'. D. Interchange connections 'S1' and 'S3'.
Description : If coils 'R1-R2-R3' at the receiver of figure 'B' shown in the illustration turned opposite of those in the transmitter, what corrective action should be taken to have both turn in the same direction? EL-0092 A ... is needed. C. Interchange leads 'R1' and 'R3'. D. Interchange leads 'R2' and 'R3'.
Description : The +5 volt regulated power supply shown in the illustration is fed directly from the _______________. EL-0094 A. 115 volt AC bus B. Annunciator Module C. +24 volt supply D. Annunciator Controller
Description : If coil 'R1-R2' at the receiver of figure 'A' shown in the illustration turned opposite of that in the transmitter, what corrective action should be taken? EL-0092 A. No action is necessary as this is ... . C. Interchange connections to 'S1' and 'S2'. D. Interchange connections to 'S1' and 'S3'.
Description : The potentiometers shown in the illustration are supplied with both (+) and (-) voltages as well as a reference to ground ________________. EL-0095 A. so there is always a spare power ... , the other for relay operation and the potentiometers are in positions where they can be accidentally touched
Description : Erratic operation of the devices represented in the diagrams shown in the illustration could be traced to ____________. EL-0092 A. improper contact at 'R' slip rings or 'S' connections B. a low three- ... . improper contact at 'S' slip rings or 'R' connections D. a high three-phase voltage supply
Description : What is the purpose of either 'setpoint module' (6000F090/030) shown in the illustration? EL-0094 A. Program the 'signal conditioner' as to how to vary its input. B. Supply 0 - 10 volts to ... . Obtain an input from the 'signal conditioner' and, if outside set limits, signals the 'annunciator'.
Description : What is the purpose of the 'annunciator module' (6000F35) shown in the illustration? EL-0094 A. Provide an input to the setpoint module. B. Drive the alarm lamp and, through the controller, the horn. ... and +24 volts to their respective power supplies. D. Connect 24 volts to both sides of the horn.
Description : In the illustration, if one of the devices labeled 'TURB' should fail the ___________. EL-0003 A. device labeled 'EXC' will drive the alternator B. device labeled 'BKR' for that ... -alternator D. emergency generator should automatically start and be placed on line to supply emergency load centers
Description : The arrow drawn through the component shown in the illustration means that the device's value _____________. EL-0015 A. is fixed and cannot be changed B. is variable between two limits C. has yet to be determined for the circuit application D. is not allowed to change during circuit operation
Description : What is represented by the two parallel lines within component 'A' of the circuit shown in the illustration? EL-0081 A. A ground connection B. An iron core C. Ventilation openings D. A mounting base
Description : In the schematic of the electrical circuit shown in the illustration, what is the value of the total capacitance, when compared to the value of equal individual capacitors? EL-0038 A. Equal B. Half C. Double D. Squared
Description : What type of logic circuit is indicated by the truth table shown in the illustration? EL-0072 A. OR B. AND C. NOR D. NAND
Description : If a voltage tester is being used to check for defective fuses in the circuit, shown in the illustration, which of the readings will indicate that fuse #2 is open? EL-0062 A. C-B full voltage B. A-D full voltage C. A-D no voltage D. C-B no voltage
Description : The wiring diagram for the motor starting circuit shown in the illustration indicates ______________. EL-0007 A. resistance starting B. reduced voltage starting C. low voltage protection D. low voltage release
Description : The electrical diagram shown in the illustration is used to depict a/an ____________. EL-0015 A. resistance circuit B. inductive circuit C. stepdown circuit D. capacitive circuit
Description : The electrical schematic shown in the illustration indicates the lighting feeder circuit is _____________. EL-0014 A. three phase, 450 volt, and 60 cycle B. three phase, 120 volt, and 60 cycle C. single phase, 120 volt, and 60 cycle D. not specified
Description : In the lighting distribution circuit shown in the illustration, if all switches are closed and fuse 'F2' were to open, all lights on branches ____________. EL-0013 A. '1', '2', and '3' would go out B. '1' ... and '3' would burn dimly D. '1' and '3' would go out, while branch '2' would remain lit
Description : The schematic diagram shown in the illustration uses symbol 'A' to represent a/an _________. EL-0011 A. non-renewable fuse link B. circuit breaker coil C. overload relay coil D. thermal overload heater
Description : When an operating motor is connected to the controller shown in the illustration, the a path of current flow through the circuit is ____________. EL-0010 A. 'L1', stop button, start button, coil 'CR', 'L2' B. 'L1' ... L2' D. 'L1', stop button, start button, 'CR' contact, 'M' contact, 'CR' coil, 'L2'
Description : If the circuit shown in the illustration were energized and operating properly, which of the devices listed would be open? EL-0007 A. The stop push-button B. The start push-button C. Contact 'Ma' D. Contact 'OL1'
Description : Which of the following actions must be carried out prior to closing the alternator circuit breaker according to the graph shown in the illustration? EL-0002 A. Increase the alternator voltage. B. Decrease the line voltage. C. Increase the line voltage. D. Decrease the line frequency.
Description : As shown in the illustration, 'B' is a ____________. EL-0058 A. single-pole, double-throw switch B. double-pole, single-throw switch C. double-pole, double-throw switch D. circuit breaker
Description : In electric circuit schematics, a transformer is represented by which of the symbols shown in the illustration? EL-0059 A. A B. B C. C D. D
Description : Sound powered telephone units 'I', 'II', and 'III' of the circuit shown in the illustration are for 'station numbers' _____________. EL-0093 A. 2, 4 and 6 B. 1, 2 and 3 C. 3, 5 and 8 D. 1, 2 and 6
Description : When replacing component 'B' of the circuit shown in the illustration, it is important to know that ____________. EL-0081 A. it is polarity sensitive and must be inserted as indicated on its ... provide the capacitor's initial charge D. it must match the circuit voltage and component 'C' wattage
Description : As shown in the illustration if the applied voltage is 12 VDC, the resistance of R1 is 10 ohms, and R2 is 10 ohms what is the total power consumed by the circuit? EL-0036 A. 3.6 watts B. 72 watts C. 7.2 watts D. 36 watts
Description : As shown in the illustration if the applied voltage is 12 VDC, the resistance of R1 is 10 ohms, and R2 is 10 ohms what is the total current in the circuit? EL-0036 A. 0.6 amp B. 0.833 amp C. 1.2 amps D. 2.4 amps
Description : As shown in the illustration if the applied voltage is 12 VDC, the resistance of R1 is 110 ohms, and R2 is 10 kohms what is the total power consumed by the circuit? EL-0036 A. 3.6 watts B. 72 watts C. .0011286 watts D. .014243 watts
Description : The proper method of connecting an ammeter in a circuit is demonstrated by which of the diagrams shown in the illustration? EL-0041 A. A B. B C. C D. All of the above
Description : What is the value of the capacitor in the astern valve position circuit shown in the illustration? EL-0099 A. 100 kFarad B. 0.5 microfarad C. 0.5 millifarad D. 50 kFarad
Description : Peripheral components for the operation of the astern valve position amplifier circuit shown in the illustration are _____________. EL-0099 A. resistors B. operated on +28 volts D.C. C. located on a separate circuit card D. all of the above