The normal road land width for a National or State highway, in open areas should be
(A) 45 m
(B) 30 m
(C) 24 m
(D) 20 m

1 Answer

Answer :

Answer: Option A

Related questions

Description : The normal road width of National and State highways (A) Is kept 45 m (B) In plain and rolling terrain built-up area, is 30 m (C) In mountainous built-up area is 20 m (D) All the above

Last Answer : Answer: Option D

Description : The normal road land width for a major district road in open area, is (A) 45 m (B) 25 m (C) 15 m (D) 12 m

Last Answer : Answer: Option B

Description : According to IRC : 52-1973, for a single lane National Highway in hilly region, (A) Width of the carriageway must be 3.75 m (B) Shoulders on either side must be 1.25 m (C) Total width of the road-way must be 6.25 m (D) Total of the above

Last Answer : Answer: Option D

Description : According to Highway Research Board of U.S.A. practical land width, is (A) 2.7 m (B) 3.0 m (C) 3.3 m (D) 3.6 m

Last Answer : Answer: Option D

Description : The minimum width of the pavement of a National Highway should be (A) 4.7 m (B) 5.7 m (C) 6.7 m (D) 7.7 m

Last Answer : Answer: Option B

Description : According to the recommendations of Nagpur Conference, the width formation of an ideal National Highway in hard rock cutting, is (A) 8.9 m (B) 7.9 m (C) 6.9 m (D) 6.5 m

Last Answer : Answer: Option B

Description : On the recommendations of Nagpur Conference, the minimum width of a village road may be (A) 2.45 m (B) 2.75 m (C) 3.66 m (D) 4.90 m

Last Answer : Answer: Option A

Description : The full width of land acquired before finalising a highway, alignment is known (A) Width of formation (B) Right of way (C) Carriage way (D) Roadway

Last Answer : Answer: Option B

Description : Road width 8.8 m of two lane National highways or State highways in mountainous terrain (A) Excludes the width of parapet (0.6 m) (B) Excludes the width of side drain (0.6 m) (C) Excludes the width of parapet and side drain (D) Includes the width of parapet and side drain

Last Answer : Answer: Option C

Description : Normal formation width of a hill road for one-way traffic, is (A) 3.6 m (B) 4.8 m (C) 6.6 m (D) 7.2 m

Last Answer : Answer: Option B

Description : The width of the right of way in urban area, is kept between 24 m to 60 m for (A) National Highways (B) State Highways (C) Both (a) and (b) (D) None of these

Last Answer : Answer: Option D

Description : In moderate exposure , the allowable crack width at the surface of concrete should be [ A ] 0.20 mm [ B ] 0.30 mm [ C ] 0.45 mm [ D ] 0.55 mm

Last Answer : [ A ] 0.20 mm

Description : The minimum road width is taken (A) 9 m (B) 12 m (C) 16 m (D) 20 m

Last Answer : Answer: Option A

Description : To prevent movement of moisture from sub-grade to road pavement at the same level as that of water-table, thickness of a cut off layer of coarse sand, is (A) 15 cm (B) 20 cm (C) 30 cm (D) 45 cm

Last Answer : Answer: Option A

Description : On the recommendations of Indian Road Congress, the ruling gradient in plains, is (A) 1 in 15 (B) 1 in 20 (C) 1 in 30 (D) 1 in 45

Last Answer : Answer: Option C

Description : The width of different roads as recommended in Nagpur plan by the Indian Road Conference for hilly region, is (A) Same for National Highways (B) Different for National Highways (C) Same for State Highways (D) Same for Major District roads

Last Answer : Answer: Option B

Description : A singly reinforced concrete beam of 25 cm width and 70 cm effective depth is provided with 18.75 cm2 steel. If the modular ratio (m) is 15, the depth of the neutral axis, is (A) 20 cm (B) 25 cm (C) 30 cm (D) 35 cm

Last Answer : Answer: Option C

Description : The stresses developed in concrete and steel in reinforced concrete beam 25 cm width and 70 cm effective depth, are 62.5 kg/cm2 and 250 kg/cm2 respectively. If m = 15, the depth of its neutral axis is (A) 20 cm (B) 25 cm (C) 30 cm (D) 35 cm

Last Answer : Answer: Option C

Description : If the width of a pavement slab is 7.5 m, thickness 20 cm and working stress 1400 kg/cm2 , spacing of 10 mm tie bars for the longitudinal joint, is (A) 10 cm (B) 20 cm (C) 30 cm (D) 40 cm

Last Answer : Answer: Option C

Description : If B is the width of formation, d is the height of the embankment, side slope S : 1, for a highway with no transverse slope, the area of cross-section is (A) B + d + Sd (B) Bd + Sd2 (C) B × d - Sd1/2 (D) ½ (Bd + Sd2

Last Answer : (B) Bd + Sd2

Description : If the number of lanes on the carriageway of a road is more than two, the total width of lane ways is equal to 3.0 m (A) + 0.60 m (B) + 0.70 m (C) + 0.90 m (D) + 1.50 m

Last Answer : Answer: Option B

Description : According to Indian Road Congress, the width of carriageway, is (A) 3.75 m for single lane (B) 7.0 m for two lanes without raised kerbs (C) 7.5 m for two lanes with raised kerbs (D) All the above

Last Answer : Answer: Option D

Description : An R.C.C beam of 25 cm width has a clear span of 5 metres and carries a U.D.L. of 2000 kg/m inclusive of its self weight. If the lever arm of the section is 45 cm., the beam is ( ... shear (B) Is safe with stirrups (C) Is safe with stirrups and inclined members (D) Needs revision of the section

Last Answer : Answer: Option A

Description : How do you drive on the open road or highway?

Last Answer : -Stay under 10 miles above the speed limit. -Make sure all lights are working. -Wear your seat belt. Highway cops will pull you over for the least of reasons. -Don't hit the road with expired tags. ... you're the least bit tired. -Drive slower at night. Animals in the road appear at the last second.

Description : To prevent movement of moisture from sub-grade to road pavement on embankments about 0.6 m to 1 m higher than water table, the thickness of cut off layer of coarse sand used, is (A) 15 cm (B) 20 cm (C) 30 cm (D) None of these

Last Answer : Answer: Option D

Description : (i) Mention two demerits of road transport. (ii) Name the terminal towns of: 1. National Highway Number 1. -Geography

Last Answer : (i) Two demerits of road transport are : 1. Roadways are not suitable for long distance travel. 2. Heavy commodities like coal and iron cannot be easily transported by roads. (ii) 1. National Highway 1 links Delhi and Amritsar. 2. National Highway 2 links Delhi and Kolkata.

Description : Maximum distance between expansion joints in structures as per IS: 456 1978 is (A) 20 m (B) 30 m (C) 45 m (D) 60 m

Last Answer : (C) 45

Description : Choose the number of National Highway in Tripura – a) 45 b) 44 c) 46 d) 31

Last Answer : b) 44

Description : The aggregate impact value of the aggregate used in (A) Building concrete is less than 45 (B) Road pavement concrete is less than 30 (C) Runway concrete is less than 30 (D) All the above

Last Answer : Answer: Option D

Description : The reinforced concrete beam which has width 25 cm, lever arm 40 cm, shear force 6t/cm2 , safe shear stress 5 kg/cm2 and B.M. 24 mt, (A) Is safe in shear (B) Is unsafe in shear (C) Is over safe in shear (D) Needs redesigning

Last Answer : Answer: Option B

Description : Roadway width for a National highways and State highways (two-lanes) is (A) 12 m (B) 9 m (C) 9.5 m (D) 15 m

Last Answer : Answer: Option A

Description : If the average daily demand of a city of 50,000 population, is 20 m.l.d., the maximum daily demand is (A) 24 mld (B) 30 mld (C) 36 mld (D) 54 mld

Last Answer : (C) 36 mld

Description : A well penetrates to 30 m below the static water table. After 24 hours of pumping at 31.40 litres/minute, the water level in a test well at a distance of 80 m is lowered by 0.5 m and in a well 20 m away water is ... 1.185 m2 /minute (B) 1.285 m2 /minute (C) 1.385 m2 /minute (D) 1.485 m2 /minute

Last Answer : Answer: Option C

Description : If Gowtham ride a bike at 30 km/hr, then he arrives at a certain place at 3 p.m. If he ride at 45 km/hr, he will arrive at the same place at 1 P.m. At what speed must he ride to get there at noon? a) 18 km/hr b) 24 km/hr c) 36 km/hr d) 28 km/hr

Last Answer : C When speed of gowtham = 30 km/hr =d/t and, When speed of the gowtham = 45 km/hr =d/(t−2) Equating the value of d: 30t =45(t-2) 30t=45t-90 15t=90 t=6 hours Finally desired speed =d/(t-1) =30t/(t-1) =30*6/(6-1) =180/5 =36 km/hr

Description : 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 23, 24, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34, 35, 36, 37, 38, 39, 40, 41, 42, 43, 44, 45, 46, 47, 48, 49, 50'. What number is missing? -Riddles

Last Answer : 22

Description : P and Q can do a piece of job in 24 days; Q and R can do it in 30 days while R and P can finish it in 40 days. If P, Q, Rworks together, in how many days will they finish the job? In how many days will each ... finish it, working alone? A) 15,25,35,45 B) 20,30,40,120 C) 20,30,40,50 D) 20,25,30,60 

Last Answer : B Time taken by (P + Q) to finish the job = 24days. (P + Q)'s 1 day's job = 1/24 Time taken by (Q +R) to finish the job = 30days. (Q + R)'s 1 day's job = 1/30 Time taken by (R + P) to finish the ... - {(P + Q)'s 1 day's job } = (1/20 -1/24)=1/120 Hence, R alone can finish the job in 120 days.

Description : From the Survey of India map, the distance of the critical point is 20 km and difference in elevation is 193 m. The over land flow time, is (A) 2 hours (B) 3 hours (C) 2 hours and 30 minutes (D) 4 hours

Last Answer : Answer: Option D

Description : Pick up the correct statement from the following: (A) Detailed survey is carried out for a strip of land about 30 m at sharp curves (B) Levels are taken along the trace cut at an interval of 20 m (C) Contour interval is generally adopted at 2 metres vertical interval (D) All the above

Last Answer : Answer: Option D

Description : A rectangle-shaped open-to-sky tank of water has a length of 2 m and a width of 1 m. If the atmospheric pressure is assumed to be 100 kPa and thickness of the tank walls is assumed to be negligible, the force exerted by ... of water is A. 20 kN B. 50 kN C. 100 kN D. 200 kN

Last Answer : 200 kN

Description : You make a diversion from the route given in the flight plan and land at an uncontrolled airfield. Within what time after landing should you inform ATC? a. 10 mins b. 20 mins c. 30 mins d. 45 mins

Last Answer : c. 30 mins

Description : You make a diversion from the route given in the flight plan and land at an uncontrolled airfield. Within what time after landing should you inform ATC? a. 10 mins b. 20 mins c. 30 mins d. 45 mins

Last Answer : c. 30 mins

Description : If depth of slab is 10 cm, width of web 30 cm, depth of web 50 cm, centre to centre distance of beams 3 m, effective span of beams 6 m, the effective flange width of the beam, is (A) 200 cm (B) 300 cm (C) 150 cm (D) 100 cm

Last Answer : Answer: Option C

Description : The excavation exceeding 1.5 m in width and 10 sq.m in plan area with a depth not exceeding 30 cm, is termed as (A) Excavation (B) Surface dressing (C) Cutting (D) Surface excavation

Last Answer : (D) Surface excavation

Description : Minimum width of ship clearance shall be (A) B or 30 m (B) 1.5 B or 50 m (C) 1.5 B (D) 50 m

Last Answer : (A) B or 30 m

Description : Pick up the incorrect statement from the following: (A) Space between the exterior walls of a warehouse and bag piles should be 30 cm (B) Cement bags should preferably be piled on wooden planks (C) Width and height of the pile should not exceed 3 m and 2.70 m respectively (D) None of these

Last Answer : Answer: Option D

Description : The width of a scaffold platform or walkways must be at least? a. 3 planks 675mm (27 inches) b. 2 planks 450mm (18 inches) c. 5 planks 1,125mm (45 inches) d. 4 planks 900mm (30 inches)

Last Answer : a. 3 planks 675mm (27 inches)

Description : In mountainous areas a natural cause for road blocks is often : (1) road repairs and construction (2) land slides (3) tree felling (4) traffic congestion

Last Answer : (2) land slides Explanation: Heavy rainfall often causes landslides in hilly regions blocking roads as a result and cutting off towns Huge amounts of debris block access, hampering traffic and affecting businesses.

Description : In mountainous areas a natural cause for road blocks is often : (1) road repairs and construction (2) land slides (3) tree felling (4) traffic congestion

Last Answer : land slides

Description : Area of steel required per metre width of pavement for a length of 20 m for design wheel load 6300 kg and permissible stress in steel 1400 kg/cm2 , is (A) 70 kg/sq cm (B) 80 kg/sq cm (C) 90 kg/sq cm (D) 100 kg/sq cm

Last Answer : Answer: Option C

Description : The pavement width of a road depends upon (A) Terrain (B) Type of traffic (C) Number of lanes (D) All the above

Last Answer : Answer: Option C