Wood is well suited to use as bearing on straw walker cranks in combine due to fact a) Wood corrosion resistance b) Split bearing are needed for practical purpose c) It can take radial as well as thrust loads d) No lubrication is required

Wood is well suited to use as bearing on straw walker cranks in combine due to fact a) Wood corrosion resistance
b) Split bearing are needed for practical purpose
c) It can take radial as well as thrust loads
d) No lubrication is required
by

1 Answer

Answer :

b) Split bearing are needed for practical purpose
by

Related questions

Tapper roller bearing are used in disc harrow because a) It can take heavy radial loads b) It can take both radial as well as end thrust c) It can operate effectively at low speed and in contact with dirt d) Both (b) and (c) are true

Description : Tapper roller bearing are used in disc harrow because a) It can take heavy radial loads b) It can take both radial as well as end thrust c) It can operate effectively at low speed and in contact with dirt d) Both (b) and (c) are true

Last Answer : d) Both (b) and (c) are true

Kinematic index of the straw Walker is as ratio (a) Angular velocity of straw Walker to angular velocity of threshing drum (b) Angular velocity of straw Walker to angular velocity of threshing drum (c) Angular velocity of straw Walker to linear velocity of combine (d) All of the above

Description : Kinematic index of the straw Walker is as ratio (a) Angular velocity of straw Walker to angular velocity of threshing drum (b) Angular velocity of straw Walker to angular velocity of threshing drum (c) Angular velocity of straw Walker to linear velocity of combine (d) All of the above

Last Answer : (a) Angular velocity of straw Walker to angular velocity of threshing drum

Angular contact bearing can take thrust as well as radial loads. (a) True (b) False

Description : Angular contact bearing can take thrust as well as radial loads. (a) True (b) False

Last Answer : (a) True

Angular contact bearing can take thrust as well as radial loads. a) True b) False

Description : Angular contact bearing can take thrust as well as radial loads. a) True b) False

Last Answer : a) True

.Incresase amount of the non grain material on the straw Walker the walker (a) Decrease (b) Increase (c) Unaffected (d) Equal

Description : .Incresase amount of the non grain material on the straw Walker the walker (a) Decrease (b) Increase (c) Unaffected (d) Equal

Last Answer : b) Increase

Increase in grain/non grain ratio on the straw Walker losses (a) Decrease (b) Increases (c) Unltered (d) None of the above

Description : Increase in grain/non grain ratio on the straw Walker losses (a) Decrease (b) Increases (c) Unltered (d) None of the above

Last Answer : (b) Increases

Increase amount of non-grain material on the straw walker _______ the walker losses a) Decreases b) Increases c) Unaffected d) Equal

Description : Increase amount of non-grain material on the straw walker _______ the walker losses a) Decreases b) Increases c) Unaffected d) Equal

Last Answer : b) Increase

Increase in grain/non-grain ratio on the straw walker, _____the straw walker losses a) Decrease b) Increase c)Unaltered d) None of the above

Description : Increase in grain/non-grain ratio on the straw walker, _____the straw walker losses a) Decrease b) Increase c)Unaltered d) None of the above

Last Answer : b) Increase

Free (threshed) seed carried over the straw discharged from the rear shoe is called as (a) Cylinder loss (b)walker loss (rack Loss) (b) Shoe loss (d) gathering loss

Description : Free (threshed) seed carried over the straw discharged from the rear shoe is called as (a) Cylinder loss (b)walker loss (rack Loss) (b) Shoe loss (d) gathering loss

Last Answer : (b) Shoe loss

Free (threshed) seed carried over the walker or rack in straw and discharge from the rear of machine is called as (a) Cylinder loss (b) walker loss(rack loss) (c) Shoe loss (d) gathering loss

Description : Free (threshed) seed carried over the walker or rack in straw and discharge from the rear of machine is called as (a) Cylinder loss (b) walker loss(rack loss) (c) Shoe loss (d) gathering loss

Last Answer : (b) walker loss(rack loss)

Unthreshed seed discharged from the rear of the machine either in straw or in the material from the cleaning shoe is called (a)cylinder loss (b)walker loss (rack loss) (c)shoe loss (d) gathering loss

Description : Unthreshed seed discharged from the rear of the machine either in straw or in the material from the cleaning shoe is called (a)cylinder loss (b)walker loss (rack loss) (c)shoe loss (d) gathering loss

Last Answer : (a)cylinder loss

Needle bearing a roller bearing having a number of smaller diameter roller is well suited to a) Application involving oscillating motion b) Exceptionally high load capacity application at low peripheral speed c) Both (a) and (b) d) None of the above

Description : Needle bearing a roller bearing having a number of smaller diameter roller is well suited to a) Application involving oscillating motion b) Exceptionally high load capacity application at low peripheral speed c) Both (a) and (b) d) None of the above

Last Answer : c) Both (a) and (b)

The bearings which resist radial loads is known as a) Ball bearing b) bush bearing c) thrust bearing d) journal bearing

Description : The bearings which resist radial loads is known as a) Ball bearing b) bush bearing c) thrust bearing d) journal bearing

Last Answer : d) journal bearing

The purpose of lubrication in an antifriction bearing is (a) to reduce the friction between balls and races (b) dissipation of frictional heat prevention of corrosion (c) protection of the bearing from dirt and other foreign particles (d) all of the mentioned

Description : The purpose of lubrication in an antifriction bearing is (a) to reduce the friction between balls and races (b) dissipation of frictional heat prevention of corrosion (c) protection of the bearing from dirt and other foreign particles (d) all of the mentioned

Last Answer : (d) all of the mentioned

The bearing material that is most susceptible to corrosion is : Q. Babbit R. Copper-lead S. Aluminium T. Aluminium-babbit

Description : The bearing material that is most susceptible to corrosion is : Q. Babbit R. Copper-lead S. Aluminium T. Aluminium-babbit

Last Answer : Q. Babbit

Deep groove ball bearings are used for (a) heavy thrust load only (b) the small angular displacement of shafts (c) radial load at high speed (d) combined thrust and radial loads at high speed

Description : Deep groove ball bearings are used for (a) heavy thrust load only (b) the small angular displacement of shafts (c) radial load at high speed (d) combined thrust and radial loads at high speed

Last Answer : (d) combined thrust and radial loads at high speed

The antifriction bearings (a) have low starting and low running friction at moderate speeds (b) have a high initial cost (c) can carry both radial and thrust loads (d) all the mentioned

Description : The antifriction bearings (a) have low starting and low running friction at moderate speeds (b) have a high initial cost (c) can carry both radial and thrust loads (d) all the mentioned

Last Answer : (d) all the mentioned

A journal bearing is a ______ contact bearing working on the hydrodynamic lubrication and which supports load in____ direction. a) Sliding, Axial b) Rolling, Radial c) Sliding, Radial d) Rolling, Axial

Description : A journal bearing is a ______ contact bearing working on the hydrodynamic lubrication and which supports load in____ direction. a) Sliding, Axial b) Rolling, Radial c) Sliding, Radial d) Rolling, Axial

Last Answer : c) Sliding, Radial

Which of the following cannot take the radial load? (a) Cylindrical Roller bearing (b) Taper roller bearing (c) Thrust ball bearing (d) Spherical roller bearing

Description : Which of the following cannot take the radial load? (a) Cylindrical Roller bearing (b) Taper roller bearing (c) Thrust ball bearing (d) Spherical roller bearing

Last Answer : (c) Thrust ball bearing

Which of the following cannot take radial load? a) Cylindrical Roller bearing b) Taper roller bearing c) Thrust ball bearing d) None of the listed

Description : Which of the following cannot take radial load? a) Cylindrical Roller bearing b) Taper roller bearing c) Thrust ball bearing d) None of the listed

Last Answer : c) Thrust ball bearing

349- Pods, heads or ears & freeseeds, lost during the cutting & conveying operation are called as..... (a) Cylinder loss (b) Walker losses ( rack loss) (c) Shoe losses (d) Gathering loss

Description : 349- Pods, heads or ears & freeseeds, lost during the cutting & conveying operation are called as..... (a) Cylinder loss (b) Walker losses ( rack loss) (c) Shoe losses (d) Gathering loss

Last Answer : (d) Gathering loss

Differential lock offers advantage of E. Threshing efficiency of thresher (power operated) F. Capacity of chaff cutters G. Cleaning capacity of straw walkers H. None of the above

Description : Differential lock offers advantage of E. Threshing efficiency of thresher (power operated) F. Capacity of chaff cutters G. Cleaning capacity of straw walkers H. None of the above

Last Answer : F. Capacity of chaff cutters

Which of the following isn’t the property of a taper roller bearing? (a) High rigidity (b) Easy dismantling (c) Take low radial and heavy loads (d) It is unsuitable for high speed applications

Description : Which of the following isn’t the property of a taper roller bearing? (a) High rigidity (b) Easy dismantling (c) Take low radial and heavy loads (d) It is unsuitable for high speed applications

Last Answer : (c) Take low radial and heavy loads

Match List-I (Type of Anti-friction bearing) with List-II (Specific Use) and select the using the code given below the Lists: [IES-2006] List-I List -II A. Self-aligning ball bearing 1. For pure axial load B. Taper roller bearing 2. For hinged condition C. Deep groove ball bearing 3. For pure radial load D. Thrust ball bearing 4. For axial and radial load A B C D A B C D (a) 2 1 3 4 (b) 3 4 2 1 (c) 2 4 3 1 (d) 3 1 2 4

Description : Match List-I (Type of Anti-friction bearing) with List-II (Specific Use) and select the using the code given below the Lists: [IES-2006] List-I List -II A. Self-aligning ball bearing 1. For pure axial load B. Taper roller bearing 2. For ... C D (a) 2 1 3 4 (b) 3 4 2 1 (c) 2 4 3 1 (d) 3 1 2 4

Last Answer : (c) 2 4 3 1

In the illustrated motor, roller bearings are used because __________. EL-0001 A. of their ability to absorb moderate thrust loads B. they electrically insulate the rotor from the frame reducing cross-currents C. the shafting and end bells do not require as close a tolerance to properly fit this type of bearing D. the clearance between the rotor and stator is generally as close as mechanical tolerance will permit

Description : In the illustrated motor, roller bearings are used because __________. EL-0001 A. of their ability to absorb moderate thrust loads B. they electrically insulate the rotor from the frame reducing ... clearance between the rotor and stator is generally as close as mechanical tolerance will permit

Last Answer : Answer: D

Which one of the following bearing is intended for a very heavy radial load? (a) Ball bearing (b) Self-aligning roller bearing (c) Roller bearing (d) Thrust bearing

Description : Which one of the following bearing is intended for a very heavy radial load? (a) Ball bearing (b) Self-aligning roller bearing (c) Roller bearing (d) Thrust bearing

Last Answer : (b) Self-aligning roller bearing

Load acting on bearing in its plane of rotation is called as a... A. Radial load B. Axial load C. Perpendicular load D. Thrust load

Description : Load acting on bearing in its plane of rotation is called as a... A. Radial load B. Axial load C. Perpendicular load D. Thrust load

Last Answer : A. Radial load

Match List I with List II and select the : [IES-2002] List I (Bearings) List II (Load type) A. Hydrodynamic Journal bearing 1. High radial and thrust load combined B. Rectangular Hydrostatic bearing 2. Radial load only C. Taper Roller bearing 3. Thrust load only D. Angular contact ball bearing 4. Medium to low radial and thrust combined A B C D A B C D (a) 2 3 1 4 (b) 4 1 3 2 (c) 2 1 3 4 (d) 4 3 1 2

Description : Match List I with List II and select the : [IES-2002] List I (Bearings) List II (Load type) A. Hydrodynamic Journal bearing 1. High radial and thrust load combined B. Rectangular Hydrostatic bearing 2. Radial load only C. Taper Roller ... (a) 2 3 1 4 (b) 4 1 3 2 (c) 2 1 3 4 (d) 4 3 1 2

Last Answer : (a) 2 3 1 4

A_______ bearing supports the load acting along the axis of the shaft. a) Thrust b) Radial c) Longitudinal d) Transversal

Description : A_______ bearing supports the load acting along the axis of the shaft. a) Thrust b) Radial c) Longitudinal d) Transversal

Last Answer : a) Thrust

What Is A Combination Thrust And Radial Bearing?

Description : What Is A Combination Thrust And Radial Bearing?

Last Answer : This unit has the ends of the Babbitt bearing extended radically over the end of the shell. Collars on the rotor face these thrust pads, and the journal is supported in the bearing between the thrust collars.

What is a combination thrust and radial bearing?

Description : What is a combination thrust and radial bearing?

Last Answer : This unit has the ends of the babbitt bearing extended radially over the end of the shell. Collars on the rotor face these thrust pads, and the journal is supported in the bearing between the thrust collars.

Consider the following pairs of types of bearings and applications: 1. Partial Journal bearing................... Rail wagon axles 2. Full journal bearing ......................Diesel engine crank-shaft 3. Radial bearing ............................Combined radial and axial loads Which of these pairs is/are correctly matched? [IES-2000] (a) 1 alone (b) 1 and 2 (c) 2 and 3 (d) 1, 2 and 3

Description : Consider the following pairs of types of bearings and applications: 1. Partial Journal bearing................... Rail wagon axles 2. Full journal bearing ......................Diesel engine crank-shaft 3. Radial bearing ... matched? [IES-2000] (a) 1 alone (b) 1 and 2 (c) 2 and 3 (d) 1, 2 and 3

Last Answer : (b) 1 and 2

Curved twisted blades are specially suited for m. Minimum tillage of trashy land at shallow depths n. Dried hard soils o. Cutting and pulverisation in wet sticky clay soil p. For operating on the sides of plant bed

Description : Curved twisted blades are specially suited for m. Minimum tillage of trashy land at shallow depths n. Dried hard soils o. Cutting and pulverisation in wet sticky clay soil p. For operating on the sides of plant bed

Last Answer : p. For operating on the sides of plant bed

shaped blades are best suited for i. Minimum tillage of trashy land at shallow depths j. Dried hard soils k. Cutting and pulverisation in wet sticky clay soil l. Working under normal field conditions

Description : shaped blades are best suited for i. Minimum tillage of trashy land at shallow depths j. Dried hard soils k. Cutting and pulverisation in wet sticky clay soil l. Working under normal field conditions

Last Answer : i. Minimum tillage of trashy land at shallow depths

Hook type blades best suited for e. Minimum tillage of trashy land at shallow depths f. Dried hard soils g. Cutting and pulverisation especially in wet sticky clay soil h. Working under normal field conditions

Description : Hook type blades best suited for e. Minimum tillage of trashy land at shallow depths f. Dried hard soils g. Cutting and pulverisation especially in wet sticky clay soil h. Working under normal field conditions

Last Answer : f. Dried hard soils

Land plane is ideally suited for a) Land levelling b) Earth moving c) Final grading d) Top finishing

Description : Land plane is ideally suited for a) Land levelling b) Earth moving c) Final grading d) Top finishing

Last Answer : d) Top finishing

Subsoiler plough is best suited for a. breaking hard pan b. deep ploughing c. making ditches d. inter cultivation

Description : Subsoiler plough is best suited for a. breaking hard pan b. deep ploughing c. making ditches d. inter cultivation

Last Answer : a. breaking hard pan

Land plane is ideally suited for: a. Land leveling b. Earth moving c. Final grading d. Top finishing

Description : Land plane is ideally suited for: a. Land leveling b. Earth moving c. Final grading d. Top finishing

Last Answer : d. Top finishing

A power tiller is most suited for : A. Draft operation with rigid tools B. Rotary cultivation C. Stationary operation D. Transport work

Description : A power tiller is most suited for : A. Draft operation with rigid tools B. Rotary cultivation C. Stationary operation D. Transport work

Last Answer : B. Rotary cultivation

A power tiller is most suited for rotary cultivation because: A. It generates negative draft B. Its traction requirements are low C. It provides high degree of soil pulverization D. All of the above

Description : A power tiller is most suited for rotary cultivation because: A. It generates negative draft B. Its traction requirements are low C. It provides high degree of soil pulverization D. All of the above

Last Answer : D. All of the above

How type furrow (or shovel) opener are especially suited to a. Stoney and root infested fields b. Poorly prepared beds in trashy soil c. Hard field with considerable debris and mulch d. None of the above

Description : How type furrow (or shovel) opener are especially suited to a. Stoney and root infested fields b. Poorly prepared beds in trashy soil c. Hard field with considerable debris and mulch d. None of the above

Last Answer : a. Stoney and root infested fields

Disc type furrow openers are especially suited to A. Stoney and root infested soils B. Poorly prepared bed in trashy soil C. Hard and sticky soil with considerable amount of debris and mulch D. All of the above

Description : Disc type furrow openers are especially suited to A. Stoney and root infested soils B. Poorly prepared bed in trashy soil C. Hard and sticky soil with considerable amount of debris and mulch D. All of the above

Last Answer : C. Hard and sticky soil with considerable amount of debris and mulch

Shoe type furrow openers especially suited to A. Stoney and root infested fields B. Poorly prepared bed in trashy soils C. Hard and sricky soil with considerable amount of mulch and debris D. All of the above

Description : Shoe type furrow openers especially suited to A. Stoney and root infested fields B. Poorly prepared bed in trashy soils C. Hard and sricky soil with considerable amount of mulch and debris D. All of the above

Last Answer : B. Poorly prepared bed in trashy soils

V-shaped sweeps are best suited for a ) Primary tillage b) Stubble mulch tillage c) Rotary tillage d) Minimum tillage

Description : V-shaped sweeps are best suited for a ) Primary tillage b) Stubble mulch tillage c) Rotary tillage d) Minimum tillage

Last Answer : b) Stubble mulch tillage

In a combine harvester the peripheral speed of the cylinder ranges between ________ m/min.

Description : In a combine harvester the peripheral speed of the cylinder ranges between ________ m/min.

Last Answer : 1200 to 1500

.total grain loss in a combine increase with a. increase in forward speed b. decrease in stubble Hight c. increase in concave clearance d. all of the above

Description : .total grain loss in a combine increase with a. increase in forward speed b. decrease in stubble Hight c. increase in concave clearance d. all of the above

Last Answer : .total grain loss in a combine increase with a. increase in forward speed b. decrease in stubble Hight c. increase in concave clearance d. all of the above

2m combine is operating at 4 kmph with an overall efficiency of 75%. The area covered by in(ha\h) will be: a. 0.4 b. 0.6 c. 0.8 d. 1.0

Description : 2m combine is operating at 4 kmph with an overall efficiency of 75%. The area covered by in(ha\h) will be: a. 0.4 b. 0.6 c. 0.8 d. 1.0

Last Answer : b. 0.6

The ratio of reel peripheral speed to forward speed of combine is called (a)velocity index (b)angular velocity index (c)reel speed index (d) kinematic index

Description : The ratio of reel peripheral speed to forward speed of combine is called (a)velocity index (b)angular velocity index (c)reel speed index (d) kinematic index

Last Answer : (c)reel speed index

Speed of the cutter bar in case of combine (grain) is (a)400-550 rpm (b) 500-800rpm (c)800-1000rpm (d) 1000-1200rpm

Description : Speed of the cutter bar in case of combine (grain) is (a)400-550 rpm (b) 500-800rpm (c)800-1000rpm (d) 1000-1200rpm

Last Answer : a)400-550 rpm

Detonation is favoured by a. Low crankshaft speed at full throttle b. .Higher loads c. Both (a) and (b) d. None of the above

Description : Detonation is favoured by a. Low crankshaft speed at full throttle b. .Higher loads c. Both (a) and (b) d. None of the above

Last Answer : c. Both (a) and (b)