Description : A shaft is subjected to bending moment M and a torque T simultaneously. The ratio of the maximum bending stress to maximum shear stress developed in the shaft, is (A) M/T (B) T/M (C) 2M/T (D) 2T/M
Last Answer : (C) 2M/T
Description : If a shaft is simultaneously subjected to a toque T and a bending moment M, the ratio of maximum bending stress and maximum shearing stress is (A) M/T (B) T/M (C) 2M/T (D) 2T/M
Description : Torque and bending moment of 100 kN.m and 200 kN.m acts on a shaft which has external diameter twice of internal diameter. What is the external diameter of the shaft which is subjected to a maximum shear stress of 90 N/mm2? a. 116.5 mm b. 233.025 mm c. 587.1 mm d. 900 mm
Last Answer : c. 587.1 mm
Description : What is the maximum shear stress induced in a solid shaft of 50 mm diameter which is subjected to both bending moment and torque of 300 kN.mm and 200 kN.mm respectively? a. 9.11 N/mm2 b. 14.69 N/mm2 c. 16.22 N/mm2 d. 20.98 N/mm2
Last Answer : b. 14.69 N/mm2
Description : A hollow prismatic beam of circular section is subjected to a torsional moment. The maximum shear stress occurs at (a) inner wall of cross section (b) middle of thickness (c) outer surface of shaft (d) none of these
Last Answer : (c) outer surface of shaft
Description : shaft subjected to a bending moment M and a torque T, experiences (A) Maximum bending stress = 32M d 3 (B) Maximum shear stress = 16 T d 3 (C) Both (a) and (b) (D) Neither (a) nor (b)
Last Answer : (C) Both (a) and (b)
Description : What is the maximum principle stress induced in a solid shaft of 40 mm diameter which is subjected to both bending moment and torque of 300 kN.mm and 150 kN.mm respectively? a. 21.69 N/mm2 b. 28.1 N/mm2 c. 50.57 N/mm2 d. 52.32 N/mm2
Last Answer : c. 50.57 N/mm2
Description : Equivalent bending moment in a shaft subjected to axial load P, torque T and bending moment M is (a) Meq = 0.5 [M + (M2 + T2)0.5]0.5 (b) Meq = 0.5 [M + (M2 + T2)0.5] (c) Meq = ( M2 + T2)0.5 (d) None
Last Answer : (b) Meq = 0.5 [M + (M2 + T2)0.5]
Description : Equivalent torque in a shaft subjected to axial load P, torque T and bending moment M is (a) Teq = (Pa2 + M2 + T2) (b) Teq = (Pa2 + M2 + T2)0.5 (c)Teq = ( M2 + T2)0.5 (d) None
Last Answer : c)Teq = ( M2 + T2)0.5
Description : A shaft a. Is always subjected to pure torsion b. Combination of M & T but no end thrust c. Combination of torque & end thrust but no bending moment d. May be subjected to a combination of M, T and end thrust
Last Answer : d. May be subjected to a combination of M, T and end thrust
Description : When a shaft is subjected to a twisting moment, every cross-section of the shaft will be under (a) Tensile stress (b) Compressive stress (c) Shear stress (d) All of these
Last Answer : c) Shear stress
Description : A transmission shaft subjected to bending loads must be designed on the basis of (a) maximum normal stress theory (b) maximum shear stress theory (c) maximum normal stress and maximum shear stress theories (d) fatigue strength
Last Answer : (a) maximum normal stress theory
Description : A solid shaft has diameter 80 mm. It is subjected to a torque of 4 KNm. The maximum shear stress induced in the shaft would be (a) 75/p N/mm2 (b) 250/p N/mm2 (c) 125/p N/mm2 (d) 150/p N/mm2
Last Answer : (c) 125/p N/mm2
Description : The bending moment ‘M’ and a torque ‘T’ is applied on a solid circular shaft. If the maximum bending stress equals to maximum shear stress developed, then ‘M’ is equal to (A) T/2 (B) T (C) 2 T (D) 4 T
Last Answer : (A) T/2
Description : Maximum shear stress in a hollow shaft subjected to a torsional moment is at the a. Middle of thickness. b. At the inner surface of the shaft. c. At the outer surface of the shaft. d. At the middle surface of the shaft.
Last Answer : c. At the outer surface of the shaft.
Description : A beam of uniform strength has a. same cross-section throughout the beam b. same bending stress at every section c. same bending moment at every section d. same shear stress at every section
Last Answer : b. same bending stress at every section
Description : The graphical representation of variation of axial load on y axis and position of cross section along x axis is called as _____ (a) Bending moment diagram (b) Shear force diagram (c) Stress-strain diagram (d) Trust diagram
Last Answer : (d) Trust diagram
Description : What is the shear stress acting on the outer surface of a hollow shaft subjected to a torque of 100 Nm?(The inner and outer diameter of the shaft is 15 mm and 30 mm respectively.) a. 50.26 N/mm2 b. 40.24 N/mm2 c. 20.120 N/mm2 d. 8.74 N/mm2
Last Answer : c. 20.120 N/mm2
Description : When the shaft is subjected to pure bending moment, the bending stress is given by? a) None of the listed b) 32M/πdᵌ c) 16M/πdᵌ d) 8M/πdᵌ
Last Answer : b) 32M/πdᵌ
Description : If the strain energy stored per unit volume in a hollow shaft subjected to a pure torque when t attains maximum shear stress fs the ratio of inner diameter to outer diameter, is 17/64 (fs/N) (A) 1/2 (B) 1/3 (C) 1/4 (D) 1/5
Last Answer : (C) 1/4
Description : Bending stress will be least at the extreme fibres for (a) Maximum area of cross section (b) Maximum moment of inertia (c) Maximum section modulus (d) None
Last Answer : (c) Maximum section modulus
Description : A solid circular shaft of diameter 100 mm is subjected to an axial stress of 50 Mpa. It is further subjected to a torque of 10 kNm. The maximum principal stress experienced on the shaft is closest to (a) 41Mpa (b) 82 Mpa (c) 164 Mpa (d) 204 Mpa
Last Answer : (b) 82 Mpa
Description : In a cantilever subjected to a combination of concentrated load, uniformly distributed load and uniformly varying load, Maximum bending moment is (a) Where shear force=0 (b) At the free end (c) At the fixed end (d) At the mid-point
Last Answer : (c) At the fixed end
Description : A transmission shaft subjected to pure bending moment should be designed on the basis of (A) Maximum principal stress theory (B) Maximum shear stress theory (C) Distortion energy theory (D) Goodman or Soderberg diagrams
Last Answer : (A) Maximum principal stress theory
Description : A circular shaft subjected to torsion undergoes a twist of 10in a length of 120 cm. If the maximum shear stress induced is limited to 1000 kg/cm2and if modulus of rigidity G = 0.8 x 106then the radius of the shaft should be (a) p/8 (b) p/27 (c) 18/p (d) 27/p
Last Answer : (d) 27/p
Description : A hollow shaft has an inner diameter of 3.7 cm and an outer diameter of 4.0 cm. A 1 kN-m torque is applied to this shaft. What is the shear stress at the mid-radius of this shaft? (a) 117Mpa (b) 178 Mpa (c) 286 Mpa (d) 363 Mpa
Last Answer : (c) 286 Mpa
Description : Magnitude of shear stress induced in a shaft due to applied torque varies from a. Maximum at centre to zero at circumference. b. Maximum at centre to minimum (not-zero) at circumference. c. Zero at centre to maximum at circumference. d. Minimum (not zero) at centre to maximum at circumference.
Last Answer : c. Zero at centre to maximum at circumference.
Description : is the pre-stressed force applied to the tendon of a rectangular pre-stressed beam whose area of cross section is and sectional modulus is . The maximum stress in the beam, subjected to a maximum bending moment , is (A) f = (P/A) + (Z/M) ... ) + (M/Z) (C) f = (P/A) + (M/Z) (D) f = (P/A) + (M/6Z)
Last Answer : Answer: Option C
Description : is the pre-stressed force applied to tendon of a rectangular pre-stressed beam whose area of cross section is and sectional modulus is . The minimum stress on the beam subjected to a maximum bending moment is (A) f = (P/A) - (Z/M) (B) f = (A/P) - (M/Z) (C) f = (P/A) - (M/Z) (D) f = (P/A) - (M/6Z)
Description : A uniformly distributed load of 20 kN/m acts on a simply supported beam of rectangular cross section of width 20 mm and depth 60 mm. What is the maximum bending stress acting on the beam of 5m? a. 5030 Mpa b. 5208 Mpa c. 6600 Mpa d. Insufficient data
Last Answer : b. 5208 Mpa
Description : The slope of shear force line at any section of the beam is also called (a) Bending moment at that section (b) Rate of loading at that section (c) Maximum Shear force (d) Maximum bending moment
Last Answer : (b) Rate of loading at that section
Description : The ratio of maximum shear stress to average shear stress is 4/3 in _______ a. circular cross-section b. rectangular cross-section c. square cross-section d. all of the above
Last Answer : a. circular cross-section
Description : Strength of a shaft a. Is equal to maximum shear stress in the shaft at the time of elastic failure b. Is equal to maximum shear stress in the shaft at the time of rupture c. Is equal to torsional rigidity d. Is ability to resist maximum twisting moment
Last Answer : d. Is ability to resist maximum twisting moment
Description : When a column is subjected to an eccentric load, the stress induced in the column will be (a) direct stress only (b) bending stress only (c) shear stress only (d) direct and bending stress both
Last Answer : (d) direct and bending stress both
Description : The variation of shear stress in a circular shaft subjected to torsion is a. Linear b. Parabolic c. Hyperbolic. d. Uniform
Last Answer : a. Linear
Description : If a circular shaft is welded to the plate by means of circumferential fillet, then the shaft is subjected to torsional moment M. If throat of weld is t, then torsional shear stress is given by a) M/2πtr2 b) M/πtr2 c) M/4πtr2 d) None of the listed
Last Answer : a) M/2πtr2
Description : A beam of T-section is subjected to a shear force of F. The maximum shear force will occur at the a. top of the section b. bottom of the section c. neutral axis of the section d. junction of web and flange
Last Answer : c. neutral axis of the section
Description : For two shafts joined in parallel, the --------------- in each shaft is same. a. shear stress. b. Angle of twist c. torque d. torsional stress.
Last Answer : b. Angle of twist
Description : For two shafts joined in series, the --------------- in each shaft is same. a. shear stress. b. Angle of twist c. torque d. torsional stress.
Last Answer : c. torque
Description : When the shaft is subjected to pure torsional moment, the torsional stress is given by? a) None of the listed b) 32M/πdᵌ c) 16M/πdᵌ d) 8M/πdᵌ
Last Answer : c) 16M/πdᵌ
Description : A hollow circular tube with a 2.3-cm I.D. and 2.5-cm O.D. is rigidly supported at its ends. A 2.5 kN-m torque is applied at the center of this tube. What is the maximum shear stress acting on this tube? (a) 2.87Mpa (b) 4.27 Mpa (c) 6.92 Mpa (d) 10.2 Mpa
Last Answer : (a) 2.87Mpa
Description : Stress in the cross section of a shaft at the centre ________ a. is zero b. decreases linearly to the maximum value of at outer surface c. both a. and b. d. none of the above
Last Answer : a. is zero
Description : When a section is subjected to two equal and opposite forces tangentially to the section, the stress produced is known as (a) Tensile stress (b) Lateral stress (c) Shear stress (d) No stress
Last Answer : (c) Shear stress
Description : Power transmitted by shaft is equal to a. Tw b. T/w c. w/T d. 2T/w
Last Answer : a. Tw
Description : In a cantilever subjected to a concentrated load (W) at the free end and having length =l, Maximum bending moment is (a) Wl at the free end (b) Wl at the fixed end (c) Wl/2 at the fixed end (d) Wl at the free end
Last Answer : (b) Wl at the fixed end
Description : In a simply supported beam subjected to uniformly distributed load (w) over the entire length (l), total load=W, maximum Bending moment is (a) Wl/8 or wl2/8 at the mid-point (b) Wl/8 or wl2/8 at the end (c) Wl/4 or wl2/4 (d) Wl/2
Last Answer : (a) Wl/8 or wl2/8 at the mid-point
Description : A cantilever beam of length of 2m carries a U.D.L. of 150 N/m over its whole span. The maximum shear force in the beam will be (a) 150 N (b) 300 N (c) 150 N-m (d) 600 N-m
Last Answer : (b) 300 N
Description : A beam is designed on the basis of a. Maximum bending moment b. Minimum shear force. c.Maximum bending moment as well as for maximum shear force d. None.
Last Answer : c.Maximum bending moment as well as for maximum shear force
Description : Point of contra-flexure is also called (a) Point of maximum Shear force (b) Point of maximum Bending moment (c) Point of inflexion (d) Fixed end
Last Answer : (c) Point of inflexion
Description : Point of contra-flexure is a (a) Point where Shear force is maximum (b) Point where Bending moment is maximum (c) Point where Bending moment is zero (d) Point where Bending moment=0 but also changes sign from positive to negative
Last Answer : (d) Point where Bending moment=0 but also changes sign from positive to negative