Equivalent torque in a shaft subjected to axial load P, torque T and bending moment M is (a) Teq = (Pa2 + M2 + T2) (b) Teq = (Pa2 + M2 + T2)0.5 (c)Teq = ( M2 + T2)0.5 (d) None

Equivalent torque in a shaft subjected to axial load P, torque T and bending moment M is (a) Teq = (Pa2 + M2 + T2)
(b) Teq = (Pa2 + M2 + T2)0.5
(c)Teq = ( M2 + T2)0.5
(d) None
by

1 Answer

Answer :

c)Teq = ( M2 + T2)0.5
by

Related questions

Equivalent bending moment in a shaft subjected to axial load P, torque T and bending moment M is (a) Meq = 0.5 [M + (M2 + T2)0.5]0.5 (b) Meq = 0.5 [M + (M2 + T2)0.5] (c) Meq = ( M2 + T2)0.5 (d) None

Description : Equivalent bending moment in a shaft subjected to axial load P, torque T and bending moment M is (a) Meq = 0.5 [M + (M2 + T2)0.5]0.5 (b) Meq = 0.5 [M + (M2 + T2)0.5] (c) Meq = ( M2 + T2)0.5 (d) None

Last Answer : (b) Meq = 0.5 [M + (M2 + T2)0.5]

A shaft a. Is always subjected to pure torsion b. Combination of M & T but no end thrust c. Combination of torque & end thrust but no bending moment d. May be subjected to a combination of M, T and end thrust

Description : A shaft a. Is always subjected to pure torsion b. Combination of M & T but no end thrust c. Combination of torque & end thrust but no bending moment d. May be subjected to a combination of M, T and end thrust

Last Answer : d. May be subjected to a combination of M, T and end thrust

The ratio of maximum bending stress to maximum shear stress on the cross section when a shaft is simultaneously subjected to a torque T and bending moment M, a. T/M b. M/T c. 2T/M d. 2M/T

Description : The ratio of maximum bending stress to maximum shear stress on the cross section when a shaft is simultaneously subjected to a torque T and bending moment M, a. T/M b. M/T c. 2T/M d. 2M/T

Last Answer : d. 2M/T

Torque and bending moment of 100 kN.m and 200 kN.m acts on a shaft which has external diameter twice of internal diameter. What is the external diameter of the shaft which is subjected to a maximum shear stress of 90 N/mm2? a. 116.5 mm b. 233.025 mm c. 587.1 mm d. 900 mm

Description : Torque and bending moment of 100 kN.m and 200 kN.m acts on a shaft which has external diameter twice of internal diameter. What is the external diameter of the shaft which is subjected to a maximum shear stress of 90 N/mm2? a. 116.5 mm b. 233.025 mm c. 587.1 mm d. 900 mm

Last Answer : c. 587.1 mm

What is the maximum shear stress induced in a solid shaft of 50 mm diameter which is subjected to both bending moment and torque of 300 kN.mm and 200 kN.mm respectively? a. 9.11 N/mm2 b. 14.69 N/mm2 c. 16.22 N/mm2 d. 20.98 N/mm2

Description : What is the maximum shear stress induced in a solid shaft of 50 mm diameter which is subjected to both bending moment and torque of 300 kN.mm and 200 kN.mm respectively? a. 9.11 N/mm2 b. 14.69 N/mm2 c. 16.22 N/mm2 d. 20.98 N/mm2

Last Answer : b. 14.69 N/mm2

What is the maximum principle stress induced in a solid shaft of 40 mm diameter which is subjected to both bending moment and torque of 300 kN.mm and 150 kN.mm respectively? a. 21.69 N/mm2 b. 28.1 N/mm2 c. 50.57 N/mm2 d. 52.32 N/mm2

Description : What is the maximum principle stress induced in a solid shaft of 40 mm diameter which is subjected to both bending moment and torque of 300 kN.mm and 150 kN.mm respectively? a. 21.69 N/mm2 b. 28.1 N/mm2 c. 50.57 N/mm2 d. 52.32 N/mm2

Last Answer : c. 50.57 N/mm2

A solid circular shaft of diameter 100 mm is subjected to an axial stress of 50 Mpa. It is further subjected to a torque of 10 kNm. The maximum principal stress experienced on the shaft is closest to (a) 41Mpa (b) 82 Mpa (c) 164 Mpa (d) 204 Mpa

Description : A solid circular shaft of diameter 100 mm is subjected to an axial stress of 50 Mpa. It is further subjected to a torque of 10 kNm. The maximum principal stress experienced on the shaft is closest to (a) 41Mpa (b) 82 Mpa (c) 164 Mpa (d) 204 Mpa

Last Answer : (b) 82 Mpa

A shaft is subjected to bending moment M and a torque T simultaneously. The ratio of the maximum bending stress to maximum shear stress developed in the shaft, is (A) M/T (B) T/M (C) 2M/T (D) 2T/M

Description : A shaft is subjected to bending moment M and a torque T simultaneously. The ratio of the  maximum bending stress to maximum shear stress developed in the shaft, is  (A) M/T (B) T/M (C) 2M/T (D) 2T/M

Last Answer : (C) 2M/T

shaft subjected to a bending moment M and a torque T, experiences (A) Maximum bending stress = 32M d 3 (B) Maximum shear stress = 16 T d 3 (C) Both (a) and (b) (D) Neither (a) nor (b)

Description :  shaft subjected to a bending moment M and a torque T, experiences  (A) Maximum bending stress = 32M d 3 (B) Maximum shear stress = 16 T d 3 (C) Both (a) and (b)  (D) Neither (a) nor (b)

Last Answer : (C) Both (a) and (b) 

When a close-coiled helical spring is subjected to an axial load, it is said to be under. (a) Bending (b) Shear (c) Torsion (d) Crushing

Description : When a close-coiled helical spring is subjected to an axial load, it is said to be under. (a) Bending (b) Shear (c) Torsion (d) Crushing

Last Answer : (c) Torsion

When the shaft is subjected to pure bending moment, the bending stress is given by? a) None of the listed b) 32M/πdᵌ c) 16M/πdᵌ d) 8M/πdᵌ

Description : When the shaft is subjected to pure bending moment, the bending stress is given by? a) None of the listed b) 32M/πdᵌ c) 16M/πdᵌ d) 8M/πdᵌ

Last Answer : b) 32M/πdᵌ

Equivalent torque in combined bending and torsion is given by a. Te = (M^2 + T^2)^1/2 b. Te = ½(M^2 + T^2)^1/2 c. Te = M + T d. Te = 1/2 [M+(M^2 + T^2)^1/2]

Description : Equivalent torque in combined bending and torsion is given by a. Te = (M^2 + T^2)^1/2 b. Te = ½(M^2 + T^2)^1/2 c. Te = M + T d. Te = 1/2 [M+(M^2 + T^2)^1/2]

Last Answer : a. Te = (M^2 + T^2)^1/2

A beam is a structural member which is subjected to (a) Axial tension or compression (b) Transverse loads and couples (c) Twisting moment (d) No load, but its axis should be horizontal and x-section rectangular or circular

Description : A beam is a structural member which is subjected to (a) Axial tension or compression (b) Transverse loads and couples (c) Twisting moment (d) No load, but its axis should be horizontal and x-section rectangular or circular

Last Answer : b) Transverse loads and couples

A solid shaft has diameter 80 mm. It is subjected to a torque of 4 KNm. The maximum shear stress induced in the shaft would be (a) 75/p N/mm2 (b) 250/p N/mm2 (c) 125/p N/mm2 (d) 150/p N/mm2

Description : A solid shaft has diameter 80 mm. It is subjected to a torque of 4 KNm. The maximum shear stress induced in the shaft would be (a) 75/p N/mm2 (b) 250/p N/mm2 (c) 125/p N/mm2 (d) 150/p N/mm2

Last Answer : (c) 125/p N/mm2

In a cantilever subjected to a combination of concentrated load, uniformly distributed load and uniformly varying load, Maximum bending moment is (a) Where shear force=0 (b) At the free end (c) At the fixed end (d) At the mid-point

Description : In a cantilever subjected to a combination of concentrated load, uniformly distributed load and uniformly varying load, Maximum bending moment is (a) Where shear force=0 (b) At the free end (c) At the fixed end (d) At the mid-point

Last Answer : (c) At the fixed end

The graphical representation of variation of axial load on y axis and position of cross section along x axis is called as _____ (a) Bending moment diagram (b) Shear force diagram (c) Stress-strain diagram (d) Trust diagram

Description : The graphical representation of variation of axial load on y axis and position of cross section along x axis is called as _____ (a) Bending moment diagram (b) Shear force diagram (c) Stress-strain diagram (d) Trust diagram

Last Answer : (d) Trust diagram

In combined bending and torsion equivalent bending moment is a. Me = (M^2 + T^2)^1/2 b. Me = ½(M^2 + T^2)^1/2 c. Me = M+(M^2 + T^2)^1/2 d. Me = 1/2 [M+(M^2 + T^2)^1/2]

Description : In combined bending and torsion equivalent bending moment is a. Me = (M^2 + T^2)^1/2 b. Me = ½(M^2 + T^2)^1/2 c. Me = M+(M^2 + T^2)^1/2 d. Me = 1/2 [M+(M^2 + T^2)^1/2]

Last Answer : d. Me = 1/2 [M+(M^2 + T^2)^1/2]

In a cantilever subjected to a concentrated load (W) at the free end and having length =l, Maximum bending moment is (a) Wl at the free end (b) Wl at the fixed end (c) Wl/2 at the fixed end (d) Wl at the free end

Description : In a cantilever subjected to a concentrated load (W) at the free end and having length =l, Maximum bending moment is (a) Wl at the free end (b) Wl at the fixed end (c) Wl/2 at the fixed end (d) Wl at the free end

Last Answer : (b) Wl at the fixed end

In a simply supported beam subjected to uniformly distributed load (w) over the entire length (l), total load=W, maximum Bending moment is (a) Wl/8 or wl2/8 at the mid-point (b) Wl/8 or wl2/8 at the end (c) Wl/4 or wl2/4 (d) Wl/2

Description : In a simply supported beam subjected to uniformly distributed load (w) over the entire length (l), total load=W, maximum Bending moment is (a) Wl/8 or wl2/8 at the mid-point (b) Wl/8 or wl2/8 at the end (c) Wl/4 or wl2/4 (d) Wl/2

Last Answer : (a) Wl/8 or wl2/8 at the mid-point

For any part of a beam subjected to uniformly distributed load, bending moment diagram is (a) Horizontal straight line (b) Vertical straight line (c) Line inclined to x-axis (d) Parabola

Description : For any part of a beam subjected to uniformly distributed load, bending moment diagram is (a) Horizontal straight line (b) Vertical straight line (c) Line inclined to x-axis (d) Parabola

Last Answer : d) Parabola

A shaft is said to be in pure torsion if a. Turning moment is applied at one end and other end is free b. Turning force is applied at one end and other end is free c. Two opposite turning moments are applied to the shaft d. Combination of torsional load and bending load is applied to the shaft

Description : A shaft is said to be in pure torsion if a. Turning moment is applied at one end and other end is free b. Turning force is applied at one end and other end is free c. Two opposite turning moments are applied to the shaft d. Combination of torsional load and bending load is applied to the shaft

Last Answer : c. Two opposite turning moments are applied to the shaft

A open helical spring under axial torque is designed on the basis of (a) Shear (b) Compression (c) Bending (d) None

Description : A open helical spring under axial torque is designed on the basis of (a) Shear (b) Compression (c) Bending (d) None

Last Answer : d) None

A closed helical spring under axial torque is designed on the basis of (a) Shear (b) Compression (c) Bending (d) None

Description : A closed helical spring under axial torque is designed on the basis of (a) Shear (b) Compression (c) Bending (d) None

Last Answer : (c) Bending

A transmission shaft subjected to bending loads must be designed on the basis of (a) maximum normal stress theory (b) maximum shear stress theory (c) maximum normal stress and maximum shear stress theories (d) fatigue strength

Description : A transmission shaft subjected to bending loads must be designed on the basis of (a) maximum normal stress theory (b) maximum shear stress theory (c) maximum normal stress and maximum shear stress theories (d) fatigue strength

Last Answer : (a) maximum normal stress theory

If a shaft is simultaneously subjected to a toque T and a bending moment M, the ratio of maximum bending stress and maximum shearing stress is (A) M/T (B) T/M (C) 2M/T (D) 2T/M

Description : If a shaft is simultaneously subjected to a toque T and a bending moment M, the ratio of maximum bending stress and maximum shearing stress is (A) M/T (B) T/M (C) 2M/T (D) 2T/M

Last Answer : (C) 2M/T

What is the shear stress acting on the outer surface of a hollow shaft subjected to a torque of 100 Nm?(The inner and outer diameter of the shaft is 15 mm and 30 mm respectively.) a. 50.26 N/mm2 b. 40.24 N/mm2 c. 20.120 N/mm2 d. 8.74 N/mm2

Description : What is the shear stress acting on the outer surface of a hollow shaft subjected to a torque of 100 Nm?(The inner and outer diameter of the shaft is 15 mm and 30 mm respectively.) a. 50.26 N/mm2 b. 40.24 N/mm2 c. 20.120 N/mm2 d. 8.74 N/mm2

Last Answer : c. 20.120 N/mm2

The bending moment ‘M’ and a torque ‘T’ is applied on a solid circular shaft. If the maximum bending stress equals to maximum shear stress developed, then ‘M’ is equal to (A) T/2 (B) T (C) 2 T (D) 4 T

Description : The bending moment ‘M’ and a torque ‘T’ is applied on a solid circular shaft. If the maximum bending stress equals to maximum shear stress developed, then ‘M’ is equal to (A) T/2 (B) T (C) 2 T (D) 4 T

Last Answer : (A) T/2

Which of the following loading is considered for the design of axles ? (a) Bending moment only (b) Twisting moment only (c) Combined bending moment and torsion (d) Combined action of bending moment, twisting moment and axial thrust

Description : Which of the following loading is considered for the design of axles ? (a) Bending moment only (b) Twisting moment only (c) Combined bending moment and torsion (d) Combined action of bending moment, twisting moment and axial thrust

Last Answer : (a) Bending moment only

In axial thrust diagram, at which point bending moment is zero? (a) Point of contra-flexure (b) Point of inflection (c) Both a. and b. (d) None of the above

Description : In axial thrust diagram, at which point bending moment is zero? (a) Point of contra-flexure (b) Point of inflection (c) Both a. and b. (d) None of the above

Last Answer : (c) Both a. and b.

Pick up the correct statement from the following: (A) Mcg = M M 2 + r2 ) where letters carry their usual meanings (B) Tcp = m 2 + T2 )where letters carry their usual meanings (C) The torque which when acting alone would produce maximum shear stress equal to the maximum shear stress caused by the combined bending and torsion, is called equivalent torque (D) All the above

Description : Pick up the correct statement from the following:  (A) Mcg = M M 2  + r2 ) where letters carry their usual meanings  (B) Tcp = m 2  + T2 )where ... maximum shear stress caused by the combined bending and torsion, is called equivalent  torque  (D) All the above 

Last Answer : (D) All the above 

A shaft turns at 150 rpm under a torque of 1500 N-m. Power transmitted is (a) 15p kW (b) 10p kW (c) 7.5p kW (d) 5p kW (IES 1999) Hint: P = 2pNT/60

Description : A shaft turns at 150 rpm under a torque of 1500 N-m. Power transmitted is (a) 15p kW (b) 10p kW (c) 7.5p kW (d) 5p kW (IES 1999) Hint: P = 2pNT/60

Last Answer : (c) 7.5p kW

A transmission shaft is subjected to bending moment (Mb) and torsional moment (Mt). The equivalent bending moment is given by, (A) √(Mb + Mt) (B) √(Mb2 + Mt2) (C) Mb + Mt (D) Mb +√(Mb2 + Mt2)

Description : A transmission shaft is subjected to bending moment (Mb) and torsional moment (Mt). The equivalent bending moment is given by, (A) √(Mb + Mt) (B) √(Mb2 + Mt2) (C) Mb + Mt (D) Mb +√(Mb2 + Mt2)

Last Answer : (D) Mb +√(Mb2 + Mt2)

A transmission shaft is subjected to bending moment (Mb) and torsional moment (Mt). The equivalent torsional moment is given by, (A) √(Mb + Mt) (B) √(Mb2 + Mt2) (C) Mb + Mt (D) Mb +√(Mb2 + Mt2)

Description : A transmission shaft is subjected to bending moment (Mb) and torsional moment (Mt). The equivalent torsional moment is given by, (A) √(Mb + Mt) (B) √(Mb2 + Mt2) (C) Mb + Mt (D) Mb +√(Mb2 + Mt2)

Last Answer : (B) √(Mb2 + Mt2)

Wahl’s stress concentration factor is used in close coiled springs under axial load to account for (a) Shear effect (b) Bending effect (c) Compression effect (d) none

Description : Wahl’s stress concentration factor is used in close coiled springs under axial load to account for (a) Shear effect (b) Bending effect (c) Compression effect (d) none

Last Answer : (b) Bending effect

A closed helical spring under axial load is designed on the basis of (a) Shear (b) Compression (c) Bending (d) None

Description : A closed helical spring under axial load is designed on the basis of (a) Shear (b) Compression (c) Bending (d) None

Last Answer : (a) Shear

A close coiled spring under axial load produces (a) Bending stresses (b) Shear stresses (c) Tensile stresses (d) None

Description : A close coiled spring under axial load produces (a) Bending stresses (b) Shear stresses (c) Tensile stresses (d) None

Last Answer : (b) Shear stresses

Bending of beam occurs under (a) Axial load (b) Transverse load (c) Direct load (d) None

Description : Bending of beam occurs under (a) Axial load (b) Transverse load (c) Direct load (d) None

Last Answer : (b) Transverse load

A concentrated load P acts on a simply supported beam of span L at a distance L/3 from the left support. The bending moment at the point of application of the load is given by (a) PL/3 (b) 2PL/3 (c) PL/9 (d) 2PL/9

Description : A concentrated load P acts on a simply supported beam of span L at a distance L/3 from the left support. The bending moment at the point of application of the load is given by (a) PL/3 (b) 2PL/3 (c) PL/9 (d) 2PL/9

Last Answer : (d) 2PL/9

In continuous beam, the intermediate beams are subjected to a. some bending moment b. no bending moment c. no slope d.no deflection

Description : In continuous beam, the intermediate beams are subjected to a. some bending moment b. no bending moment c. no slope d.no deflection

Last Answer : a. some bending moment

A member subjected to couple produces rotational motion about its longitudinal axis called as ________ a. torsion b. twisting moment c. both a. and b. d. bending moment

Description : A member subjected to couple produces rotational motion about its longitudinal axis called as ________ a. torsion b. twisting moment c. both a. and b. d. bending moment

Last Answer : c. both a. and b.

When a beam is subjected to a bending moment the strain in a layer is …………the distance from the neutral axis. (a) Independent of (b) Directly proportional to (c) Inversely proportional to (d) None of these

Description : When a beam is subjected to a bending moment the strain in a layer is …………the distance from the neutral axis. (a) Independent of (b) Directly proportional to (c) Inversely proportional to (d) None of these

Last Answer : (b) Directly proportional to

When the shaft is subjected to pure torsional moment, the torsional stress is given by? a) None of the listed b) 32M/πdᵌ c) 16M/πdᵌ d) 8M/πdᵌ

Description : When the shaft is subjected to pure torsional moment, the torsional stress is given by? a) None of the listed b) 32M/πdᵌ c) 16M/πdᵌ d) 8M/πdᵌ

Last Answer : c) 16M/πdᵌ

A hollow prismatic beam of circular section is subjected to a torsional moment. The maximum shear stress occurs at (a) inner wall of cross section (b) middle of thickness (c) outer surface of shaft (d) none of these

Description : A hollow prismatic beam of circular section is subjected to a torsional moment. The maximum shear stress occurs at (a) inner wall of cross section (b) middle of thickness (c) outer surface of shaft (d) none of these

Last Answer : (c) outer surface of shaft

When a shaft is subjected to a twisting moment, every cross-section of the shaft will be under (a) Tensile stress (b) Compressive stress (c) Shear stress (d) All of these

Description : When a shaft is subjected to a twisting moment, every cross-section of the shaft will be under (a) Tensile stress (b) Compressive stress (c) Shear stress (d) All of these

Last Answer : c) Shear stress

Maximum shear stress in a hollow shaft subjected to a torsional moment is at the a. Middle of thickness. b. At the inner surface of the shaft. c. At the outer surface of the shaft. d. At the middle surface of the shaft.

Description : Maximum shear stress in a hollow shaft subjected to a torsional moment is at the a. Middle of thickness. b. At the inner surface of the shaft. c. At the outer surface of the shaft. d. At the middle surface of the shaft.

Last Answer : c. At the outer surface of the shaft.

A circular shaft subjected to torsion undergoes a twist of 10in a length of 120 cm. If the maximum shear stress induced is limited to 1000 kg/cm2and if modulus of rigidity G = 0.8 x 106then the radius of the shaft should be (a) p/8 (b) p/27 (c) 18/p (d) 27/p

Description : A circular shaft subjected to torsion undergoes a twist of 10in a length of 120 cm. If the maximum shear stress induced is limited to 1000 kg/cm2and if modulus of rigidity G = 0.8 x 106then the radius of the shaft should be (a) p/8 (b) p/27 (c) 18/p (d) 27/p

Last Answer : (d) 27/p

The product of the tangential force acting on the shaft and radius of shaft known as (a) Torsional rigidity (b) Flexural rigidity (c) Bending moment (d) Twisting moment

Description : The product of the tangential force acting on the shaft and radius of shaft known as (a) Torsional rigidity (b) Flexural rigidity (c) Bending moment (d) Twisting moment

Last Answer : (d) Twisting moment

The unit of Torque in SI units (a) kg-m (b) kg-cm (c) N-m (d) N/m2

Description : The unit of Torque in SI units (a) kg-m (b) kg-cm (c) N-m (d) N/m2

Last Answer : (c) N-m

When a column is subjected to an eccentric load, the stress induced in the column will be (a) direct stress only (b) bending stress only (c) shear stress only (d) direct and bending stress both

Description : When a column is subjected to an eccentric load, the stress induced in the column will be (a) direct stress only (b) bending stress only (c) shear stress only (d) direct and bending stress both

Last Answer : (d) direct and bending stress both

A hollow shaft has an inner diameter of 3.7 cm and an outer diameter of 4.0 cm. A 1 kN-m torque is applied to this shaft. What is the shear stress at the mid-radius of this shaft? (a) 117Mpa (b) 178 Mpa (c) 286 Mpa (d) 363 Mpa

Description : A hollow shaft has an inner diameter of 3.7 cm and an outer diameter of 4.0 cm. A 1 kN-m torque is applied to this shaft. What is the shear stress at the mid-radius of this shaft? (a) 117Mpa (b) 178 Mpa (c) 286 Mpa (d) 363 Mpa

Last Answer : (c) 286 Mpa