A cantilever of length 2m carries a point load of 30KN at the free end.If I = 108 mm4 and E= 2×105 N/mm2. What is the slope of the cantilever at the free end? a.0.503 rad b.0.677 rad c. 0.003 rad d.0.008

A cantilever of length 2m carries a point load of 30KN at the free end.If I = 108 mm4 and E= 2×105 N/mm2. What is the slope of the cantilever at the free end?
a.0.503 rad
b.0.677 rad
c. 0.003 rad
d.0.008
by

1 Answer

Answer :

c. 0.003 rad
by

Related questions

A cantilever of length 3m carries a uniformly distributed load of 15KN/m over a length of 2m from the free end.If I= 108 mm4 and E= 2×105 N/mm2,find the slope at the free end? a.0.00326 rad b.0.00578 rad c.0.00677 rad d.0.00786 rad

Description : A cantilever of length 3m carries a uniformly distributed load of 15KN/m over a length of 2m from the free end.If I= 108 mm4 and E= 2×105 N/mm2,find the slope at the free end? a.0.00326 rad b.0.00578 rad c.0.00677 rad d.0.00786 rad

Last Answer : a.0.00326 rad

A cantilever of length 3 m carries two point loads of 2 KN at the free end and 4KN at a distance of 1m from the free end .What is the deflection at the free end? Take E= 2×105 N/mm2and I= 108 mm4. a.2.56 mm b.3.84 mm c.1.84 mm d.5.26mm

Description : A cantilever of length 3 m carries two point loads of 2 KN at the free end and 4KN at a distance of 1m from the free end .What is the deflection at the free end? Take E= 2×105 N/mm2and I= 108 mm4. a.2.56 mm b.3.84 mm c.1.84 mm d.5.26mm

Last Answer : c.1.84 mm

A cantilever of length 3m carries a point load of 60 KN at a distance of 2m from the fixed end.If E= 2×105 and I=108, what is the deflection at the free end?. a.7 mm b.14 mm c.26 mm d.52 mm.

Description : A cantilever of length 3m carries a point load of 60 KN at a distance of 2m from the fixed end.If E= 2×105 and I=108, what is the deflection at the free end?. a.7 mm b.14 mm c.26 mm d.52 mm.

Last Answer : b.14 mm

A cantilever of length 3 m carries a uniformly distributed load over the entire length.If the deflection at the free end is 40 mm,find the slope at the free end. a.0.0115 rad b.0.01777 rad c.0.001566 rad d.0.00144 rad

Description : A cantilever of length 3 m carries a uniformly distributed load over the entire length.If the deflection at the free end is 40 mm,find the slope at the free end. a.0.0115 rad b.0.01777 rad c.0.001566 rad d.0.00144 rad

Last Answer : b.0.01777 rad

The slope at the free end of a cantilever of length 1m is 10 .If the cantilever carries a uniformly distributed load over the whole length ,then the deflection at the free end will be a.1cm b.1.309 cm c.2.618 cm. d.3.927cm.

Description : The slope at the free end of a cantilever of length 1m is 10 .If the cantilever carries a uniformly distributed load over the whole length ,then the deflection at the free end will be a.1cm b.1.309 cm c.2.618 cm. d.3.927cm.

Last Answer : b.1.309 cm

A cantilever beam of length of 2m carries a U.D.L. of 150 N/m over its whole span. The maximum shear force in the beam will be (a) 150 N (b) 300 N (c) 150 N-m (d) 600 N-m

Description : A cantilever beam of length of 2m carries a U.D.L. of 150 N/m over its whole span. The maximum shear force in the beam will be (a) 150 N (b) 300 N (c) 150 N-m (d) 600 N-m

Last Answer : (b) 300 N

A cantilever beam of span 3m carries a point load 100 N at the free end. The maximum B.M in the beam will be (a) 100 N-m (b) 300 N-m (c) 150 N-m (d) 600 N-m

Description : A cantilever beam of span 3m carries a point load 100 N at the free end. The maximum B.M in the beam will be (a) 100 N-m (b) 300 N-m (c) 150 N-m (d) 600 N-m

Last Answer : (b) 300 N-m

If a solid shaft (diameter 20 cm, length 400 cm, N = 0.8 × 105 N/mm2 ) when subjected to a twisting moment, produces maximum shear stress of 50 N/mm2 , the angle of twist in radians, is (A) 0.001 (B) 0.002 (C) 0.0025 (D) 0.003

Description : If a solid shaft (diameter 20 cm, length 400 cm, N = 0.8 × 105  N/mm2 ) when subjected to a twisting  moment, produces maximum shear stress of 50 N/mm2 , the angle of twist in radians, is  (A) 0.001  (B) 0.002  (C) 0.0025  (D) 0.003 

Last Answer : (C) 0.0025 

A beam of uniform rectangular section 200 mm wide and 300mm deep is simply supported at its ends.It carries a uniformly distributed load of 9KN/m run over the entire span of 5m.If E=1×104 N/mm2, what is the maximum deflection? a.14.26 mm b.17.28 mm c.18.53 mm d.16.27 mm.

Description : A beam of uniform rectangular section 200 mm wide and 300mm deep is simply supported at its ends.It carries a uniformly distributed load of 9KN/m run over the entire span of 5m.If E=1×104 N/mm2, what is the maximum deflection? a.14.26 mm b.17.28 mm c.18.53 mm d.16.27 mm.

Last Answer : d.16.27 mm.

What is the S.I. unit of sectional modulus? a. mm4 b. mm3 c. mm2 d. m

Description : What is the S.I. unit of sectional modulus? a. mm4 b. mm3 c. mm2 d. m

Last Answer : b. mm3

Maximum slope in a cantilever beam with UDL w over the entire length will be a. At the free end. b. At the fixed end. c. At the centre d. None.

Description : Maximum slope in a cantilever beam with UDL w over the entire length will be a. At the free end. b. At the fixed end. c. At the centre d. None.

Last Answer : a. At the free end.

A simply supported rolled steel joist 8 m long carries a uniformly distributed load over it span so that the maximum bending stress is 75 N/mm². If the slope at the ends is 0.005 radian and the value of E = 0.2 × 106 N/mm2 , the depth of the joist, is (A) 200 mm (B) 250 mm (C) 300 mm (D) 400 mm

Description : A simply supported rolled steel joist 8 m long carries a uniformly distributed load over it span so  that the maximum bending stress is 75 N/mm². If the slope at the ends is 0.005 radian and the  value of E = 0.2 ... joist, is  (A) 200 mm  (B) 250 mm  (C) 300 mm  (D) 400 mm 

Last Answer : (D) 400 mm 

In a cantilever subjected to a combination of concentrated load, uniformly distributed load and uniformly varying load, Maximum bending moment is (a) Where shear force=0 (b) At the free end (c) At the fixed end (d) At the mid-point

Description : In a cantilever subjected to a combination of concentrated load, uniformly distributed load and uniformly varying load, Maximum bending moment is (a) Where shear force=0 (b) At the free end (c) At the fixed end (d) At the mid-point

Last Answer : (c) At the fixed end

In a cantilever subjected to a concentrated load (W) at the free end and having length =l, Maximum bending moment is (a) Wl at the free end (b) Wl at the fixed end (c) Wl/2 at the fixed end (d) Wl at the free end

Description : In a cantilever subjected to a concentrated load (W) at the free end and having length =l, Maximum bending moment is (a) Wl at the free end (b) Wl at the fixed end (c) Wl/2 at the fixed end (d) Wl at the free end

Last Answer : (b) Wl at the fixed end

.Maximum slope in a cantilever beam with a Moment M at the free end will be a. 3ML/EI. b.2ML/EI. C. ML/EI. d. None.

Description : .Maximum slope in a cantilever beam with a Moment M at the free end will be a. 3ML/EI. b.2ML/EI. C. ML/EI. d. None.

Last Answer : C. ML/EI.

Maximum slope in a cantilever beam with W at the free end will be a.WL2/4EI b.WL2/8EI c.WL2/2EI d.None.

Description : Maximum slope in a cantilever beam with W at the free end will be a.WL2/4EI b.WL2/8EI c.WL2/2EI d.None.

Last Answer : c.WL2/2EI

Maximum slope in a cantilever beam with W at the free end will be a.at the free end. b. at the centre c.at the fixed end. d.None.

Description : Maximum slope in a cantilever beam with W at the free end will be a.at the free end. b. at the centre c.at the fixed end. d.None.

Last Answer : a.at the free end.

In cantilever beam the slope and deflection at the free end is ---------. a.zero b.maximum c.minimum d.none of above.

Description : In cantilever beam the slope and deflection at the free end is ---------. a.zero b.maximum c.minimum d.none of above.

Last Answer : b.maximum

A cantilever of length 2 cm and depth 10 cm tapers in plan from a width 24 cm to zero at its free end. If the modulus of elasticity of the material is 0.2 × 106 N/mm2 , the deflection of the free end, is (A) 2 mm (B) 3 mm (C) 4 mm (D) 5 mm

Description : A cantilever of length 2 cm and depth 10 cm tapers in plan from a width 24 cm to zero at its free  end. If the modulus of elasticity of the material is 0.2 × 106  N/mm2 , the deflection of the free end,  is  (A) 2 mm  (B) 3 mm  (C) 4 mm  (D) 5 mm

Last Answer : (D) 5 mm

The bending moment diagram for a cantilever with point load, at the free end will be (a) A triangle with max. height under free end (b) A triangle with max. height under fixed end (c) A parabolic curve (d) None of these

Description : The bending moment diagram for a cantilever with point load, at the free end will be (a) A triangle with max. height under free end (b) A triangle with max. height under fixed end (c) A parabolic curve (d) None of these

Last Answer : (b) A triangle with max. height under fixed end

Maximum slope in a cantilever beam with UDL w over the entire length will be a. wl3/9EI b. wl3/6EI c. wl3/3EI d. None.

Description : Maximum slope in a cantilever beam with UDL w over the entire length will be a. wl3/9EI b. wl3/6EI c. wl3/3EI d. None.

Last Answer : b. wl3/6EI

A column has moment of inertia about X-X and Y-Y axis as follows IXX=4234.4 mm4 IYY=236.3 mm4 This column will buckle about (a) X-X axis (b) Y-Y axis (c) It depends upon the applied load (d) None of these

Description : A column has moment of inertia about X-X and Y-Y axis as follows IXX=4234.4 mm4 IYY=236.3 mm4 This column will buckle about (a) X-X axis (b) Y-Y axis (c) It depends upon the applied load (d) None of these

Last Answer : (b) Y-Y axis

In a cantilever carrying a uniformly varying load starting from zero at the free end, the Bending moment diagram is (a) A horizontal line parallel to x-axis (b) A line inclined to x-axis (c) Follows a parabolic law (d) Follows a cubic law

Description : In a cantilever carrying a uniformly varying load starting from zero at the free end, the Bending moment diagram is (a) A horizontal line parallel to x-axis (b) A line inclined to x-axis (c) Follows a parabolic law (d) Follows a cubic law

Last Answer : (d) Follows a cubic law

In a cantilever carrying a uniformly varying load starting from zero at the free end, the shear force diagram is (a) A horizontal line parallel to x-axis (b) A line inclined to x-axis (c) Follows a parabolic law (d) Follows a cubic law

Description : In a cantilever carrying a uniformly varying load starting from zero at the free end, the shear force diagram is (a) A horizontal line parallel to x-axis (b) A line inclined to x-axis (c) Follows a parabolic law (d) Follows a cubic law

Last Answer : (c) Follows a parabolic law

Maximum deflection in a cantilever beam with UDL w over the entire length will be a. At the free end. b. At the fixed end. c. At the centre d. None.

Description : Maximum deflection in a cantilever beam with UDL w over the entire length will be a. At the free end. b. At the fixed end. c. At the centre d. None.

Last Answer : a. At the free end.

A cantilever carries is uniformly distributed load W over its whole length and a force W acts at its free end upward. The net deflection of the free end will be (A) Zero (B) (5/24) (WL3 /EI) upward (C) (5/24) (WL3 /EI) downward (D) None of these

Description : A cantilever carries is uniformly distributed load W over its whole length and a force W acts at its  free end upward. The net deflection of the free end will be  (A) Zero  (B) (5/24) (WL3 /EI) upward  (C) (5/24) (WL3 /EI) downward  (D) None of these 

Last Answer : (B) (5/24) (WL3 /EI) upward

A leaf spring consists of 3 extra full length leaves and 14 graduated length leaves. The maximum force that can act on the spring is 70kN and the distance between eyes of the spring is 1.2m. Width and thickness of the leaves are 100mm and 12mm respectively. Calculate the initial pre load required to close the nip. (a) 4332.2N (b) 4674.1N (c) 4985.4N (d) Can’t be determined

Description : A leaf spring consists of 3 extra full length leaves and 14 graduated length leaves. The maximum force that can act on the spring is 70kN and the distance between eyes of the spring is 1.2m. Width and thickness of the ... close the nip. (a) 4332.2N (b) 4674.1N (c) 4985.4N (d) Can't be determined

Last Answer : (b) 4674.1N

A water main 1 m in diameter contains a fluid having pressure 1 N/mm2. If the maximum permissible tensile stress in the metal is 20 N/mm2, th thickness of the metal required would be a) 2 cm b) 2.5cm c) 1 cm d) 0.5 cm

Description : A water main 1 m in diameter contains a fluid having pressure 1 N/mm2. If the maximum permissible tensile stress in the metal is 20 N/mm2, th thickness of the metal required would be a) 2 cm b) 2.5cm c) 1 cm d) 0.5 cm

Last Answer : b) 2.5cm

A rod, 120cm long and of diameter 3.0 cm is subjected to an axial pull of 18 kN. The stress in N/mm2 is. a. 22.57 b. 23.47 c. 24.57 d. 25.47

Description : A rod, 120cm long and of diameter 3.0 cm is subjected to an axial pull of 18 kN. The stress in N/mm2 is. a. 22.57 b. 23.47 c. 24.57 d. 25.47

Last Answer : d. 25.47

A simply supported beam carries a uniformly distributed load over the whole span.The deflection at the centre is y.If the distributed load per unit length is doubled and also depth of beam is doubled ,then the deflection at the centre would be a.2y b.4y c.y/2 d.y/4.

Description : A simply supported beam carries a uniformly distributed load over the whole span.The deflection at the centre is y.If the distributed load per unit length is doubled and also depth of beam is doubled ,then the deflection at the centre would be a.2y b.4y c.y/2 d.y/4.

Last Answer : d.y/4.

A simply supported beam carries uniformly distributed load of 20 kN/m over the length of 5 m. If flexural rigidity is 30000 kN.m2, what is the maximum deflection in the beam? a. 5.4 mm b. 1.08 mm c. 6.2 mm d. 8.6 mm

Description : A simply supported beam carries uniformly distributed load of 20 kN/m over the length of 5 m. If flexural rigidity is 30000 kN.m2, what is the maximum deflection in the beam? a. 5.4 mm b. 1.08 mm c. 6.2 mm d. 8.6 mm

Last Answer : a. 5.4 mm

What is the moment of inertia acting on a semicircle of radius 20 mm about the asymmetrical axes? a. 125.663 x 103 mm4 b. 17600 mm4 c. 1500 mm4 d. 8800 mm4

Description : What is the moment of inertia acting on a semicircle of radius 20 mm about the asymmetrical axes? a. 125.663 x 103 mm4 b. 17600 mm4 c. 1500 mm4 d. 8800 mm4

Last Answer : b. 17600 mm4

What is the moment of inertia acting on a circle of diameter 50 mm? a. 122.71 x 103 mm4 b. 306.79 x 103 mm4 c. 567.23 x 103 mm4 d. 800 x 103 mm4

Description : What is the moment of inertia acting on a circle of diameter 50 mm? a. 122.71 x 103 mm4 b. 306.79 x 103 mm4 c. 567.23 x 103 mm4 d. 800 x 103 mm4

Last Answer : b. 306.79 x 103 mm4

What is the moment of inertia acting on a rectangle of width 15 mm and depth 40 mm about base by using theorem of parallel axes? a. 320 x 103 mm4 b. 300 x 103 mm4 c. 240 x 103 mm4 d. 80 x 103 mm

Description : What is the moment of inertia acting on a rectangle of width 15 mm and depth 40 mm about base by using theorem of parallel axes? a. 320 x 103 mm4 b. 300 x 103 mm4 c. 240 x 103 mm4 d. 80 x 103 mm

Last Answer : a. 320 x 103 mm4

Maximum deflection in a cantilever beam with W at the free end will be a. at the free end. b.at the fixed end. c.at the centre d.None.

Description : Maximum deflection in a cantilever beam with W at the free end will be a. at the free end. b.at the fixed end. c.at the centre d.None.

Last Answer : a. at the free end.

Maximum deflection in a cantilever beam with W at the free end will be a.WL3/6EI. b.WL3/2EI c.WL3/3EI d.None.

Description : Maximum deflection in a cantilever beam with W at the free end will be a.WL3/6EI. b.WL3/2EI c.WL3/3EI d.None.

Last Answer : c.WL3/3EI

In case of a cantilever beam, bending moment at the free end will be (a) Maximum (b) Minimum (c) Zero (d) None

Description : In case of a cantilever beam, bending moment at the free end will be (a) Maximum (b) Minimum (c) Zero (d) None

Last Answer : c) Zero

A cantilever is a beam whose (a) Both ends are supported either on rollers or hinges (b) One end is fixed and other end is free (c) Both ends are fixed (d) Whose both or one of the end has overhang

Description : A cantilever is a beam whose (a) Both ends are supported either on rollers or hinges (b) One end is fixed and other end is free (c) Both ends are fixed (d) Whose both or one of the end has overhang

Last Answer : b) One end is fixed and other end is free

A reinforced concrete cantilever beam is 3.6 m long, 25 cm wide and has its lever arm 40 cm. It carries a load of 1200 kg at its free end and vertical stirrups can carry 1800 kg. Assuming concrete to carry one-third of the diagonal tension and ignoring the weight of the beam, the number of shear stirrups required, is (A) 30 (B) 35 (C) 40 (D) 45

Description : A reinforced concrete cantilever beam is 3.6 m long, 25 cm wide and has its lever arm 40 cm. It carries a load of 1200 kg at its free end and vertical stirrups can carry 1800 kg. Assuming concrete to carry one- ... beam, the number of shear stirrups required, is (A) 30 (B) 35 (C) 40 (D) 45

Last Answer : Answer: Option C

A helical spring is fabricated by wrapping wire 19.05 mm in diameter around a forming cylinder 203.2 mm in diameter. Compute the number of turns required to permit an elongation of 101.6 mm. without exceeding a shearing stress of 124 N/mm2. G = 82737 N/mm2. a. 10 turns b. 20 turns c. 25 turns d. 30 turns

Description : A helical spring is fabricated by wrapping wire 19.05 mm in diameter around a forming cylinder 203.2 mm in diameter. Compute the number of turns required to permit an elongation of 101.6 mm. without exceeding a shearing ... G = 82737 N/mm2. a. 10 turns b. 20 turns c. 25 turns d. 30 turns

Last Answer : a. 10 turns

A solid shaft has diameter 80 mm. It is subjected to a torque of 4 KNm. The maximum shear stress induced in the shaft would be (a) 75/p N/mm2 (b) 250/p N/mm2 (c) 125/p N/mm2 (d) 150/p N/mm2

Description : A solid shaft has diameter 80 mm. It is subjected to a torque of 4 KNm. The maximum shear stress induced in the shaft would be (a) 75/p N/mm2 (b) 250/p N/mm2 (c) 125/p N/mm2 (d) 150/p N/mm2

Last Answer : (c) 125/p N/mm2

Torque and bending moment of 100 kN.m and 200 kN.m acts on a shaft which has external diameter twice of internal diameter. What is the external diameter of the shaft which is subjected to a maximum shear stress of 90 N/mm2? a. 116.5 mm b. 233.025 mm c. 587.1 mm d. 900 mm

Description : Torque and bending moment of 100 kN.m and 200 kN.m acts on a shaft which has external diameter twice of internal diameter. What is the external diameter of the shaft which is subjected to a maximum shear stress of 90 N/mm2? a. 116.5 mm b. 233.025 mm c. 587.1 mm d. 900 mm

Last Answer : c. 587.1 mm

What is the maximum shear stress induced in a solid shaft of 50 mm diameter which is subjected to both bending moment and torque of 300 kN.mm and 200 kN.mm respectively? a. 9.11 N/mm2 b. 14.69 N/mm2 c. 16.22 N/mm2 d. 20.98 N/mm2

Description : What is the maximum shear stress induced in a solid shaft of 50 mm diameter which is subjected to both bending moment and torque of 300 kN.mm and 200 kN.mm respectively? a. 9.11 N/mm2 b. 14.69 N/mm2 c. 16.22 N/mm2 d. 20.98 N/mm2

Last Answer : b. 14.69 N/mm2

What is the maximum principle stress induced in a solid shaft of 40 mm diameter which is subjected to both bending moment and torque of 300 kN.mm and 150 kN.mm respectively? a. 21.69 N/mm2 b. 28.1 N/mm2 c. 50.57 N/mm2 d. 52.32 N/mm2

Description : What is the maximum principle stress induced in a solid shaft of 40 mm diameter which is subjected to both bending moment and torque of 300 kN.mm and 150 kN.mm respectively? a. 21.69 N/mm2 b. 28.1 N/mm2 c. 50.57 N/mm2 d. 52.32 N/mm2

Last Answer : c. 50.57 N/mm2

What is the shear stress acting on the outer surface of a hollow shaft subjected to a torque of 100 Nm?(The inner and outer diameter of the shaft is 15 mm and 30 mm respectively.) a. 50.26 N/mm2 b. 40.24 N/mm2 c. 20.120 N/mm2 d. 8.74 N/mm2

Description : What is the shear stress acting on the outer surface of a hollow shaft subjected to a torque of 100 Nm?(The inner and outer diameter of the shaft is 15 mm and 30 mm respectively.) a. 50.26 N/mm2 b. 40.24 N/mm2 c. 20.120 N/mm2 d. 8.74 N/mm2

Last Answer : c. 20.120 N/mm2

A square object of 4 mm is subjected to a force of 3000 N. What is the maximum allowable shear stress acting on it? a. 250.14 mm2 b. 281.25 mm2 c. 400.32 mm2 d. 500 mm2

Description : A square object of 4 mm is subjected to a force of 3000 N. What is the maximum allowable shear stress acting on it? a. 250.14 mm2 b. 281.25 mm2 c. 400.32 mm2 d. 500 mm2

Last Answer : b. 281.25 mm2

What is the shear stress acting along the neutral axis of triangular beam section, with base 60 mm and height 150 mm, when shear force of 30 kN acts? a. 15.36 N/mm2 b. 10.6 N/mm2 c. 8.88 N/mm2 d. Insufficient data

Description : What is the shear stress acting along the neutral axis of triangular beam section, with base 60 mm and height 150 mm, when shear force of 30 kN acts? a. 15.36 N/mm2 b. 10.6 N/mm2 c. 8.88 N/mm2 d. Insufficient data

Last Answer : c. 8.88 N/mm2

What is the average shear stress acting on a rectangular beam, if 50 N/mm2is the maximum shear stress acting on it? a. 31.5 N/mm2 b. 33.33 N/mm2 c. 37.5 N/mm2 d. 42.5 N/mm2

Description : What is the average shear stress acting on a rectangular beam, if 50 N/mm2is the maximum shear stress acting on it? a. 31.5 N/mm2 b. 33.33 N/mm2 c. 37.5 N/mm2 d. 42.5 N/mm2

Last Answer : b. 33.33 N/mm2

A steel bar 20 mm in diameter simply-supported at its ends over a total span of 40 cm carries a load at its centre. If the maximum stress induced in the bar is limited to N/mm2, the bending strain energy stored in the bar, is (A) 411 N mm (B) 511 N mm (C) 611 N mm (D) 711 N mm

Description : A steel bar 20 mm in diameter simply-supported at its ends over a total span of 40 cm carries a  load at its centre. If the maximum stress induced in the bar is limited to N/mm2, the bending  strain energy stored in the ... (A) 411 N mm  (B) 511 N mm  (C) 611 N mm  (D) 711 N mm 

Last Answer : (C) 611 N mm 

A long column with fixed ends can carry load as compared to cantilever column (a) 4 times (b) 8 times (c) 16 times (d) None

Description : A long column with fixed ends can carry load as compared to cantilever column (a) 4 times (b) 8 times (c) 16 times (d) None

Last Answer : (c) 16 times