Description : The following is a type of leaf springs (a) three Quarter elliptic (b) semi elliptic (c) quarter elliptic (d) all of the above
Last Answer : (d) all of the above
Description : ------------ are called cantilever laminated springs (a) Semi-elliptical springs (b) quarter elliptical springs (c) both (a) and (b) (d) none (Ans: b)
Last Answer : (b) quarter elliptical springs
Description : In case of a laminated spring, the load at which the plates become straight is called (a) working load (b) safe load (c) proof load (d) none
Last Answer : (c) proof load
Description : The longest leaf in Semi-elliptic leaf spring is known as (A) chief leaf (B) master leaf (C) major leaf (D) higher leaf
Last Answer : (B) master leaf
Description : Laminated springs are used in (a) Watches (b) Sofas (c) Motorcycles (d) None
Last Answer : (d) None
Description : The laminated springs are given initial curvature (a) To have uniform strength (b) To make it more economical (c) So that plates may become flat, when subjected to design load (d) None of these
Last Answer : (c) So that plates may become
Last Answer : (c) So that plates may become flat, when subjected to design load
Description : he most common value of spring index lies between (a) 0 and 5 (b) 5 and 10 (c) 10 and 15 (d) None
Last Answer : b) 5 and 10
Description : The region of the cross-section of a column in which compressive load may be applied without producing any tensile stress, is known as the core of the cross-section. In circular columns the radius of the core, ... One-third of the radius (c) One-quarter of the radius (d) One-fifth of the radius
Last Answer : (c) One-quarter of the radius
Description : In a simply supported beam carrying a uniformly distributed load over the left half span, the point of contraflexure will occur in (a) Left half span of the beam (b) Right half span of the beam. (c) Quarter points of the beam (d) Does not exist
Last Answer : (d) Does not exist
Description : Among the cylindrical and spherical thin vessels of same material, diameter and pressure which has the lesser thickness a. Cylindrical shell b. Spherical shell c. Cylindrical shell with semi spherical heads d. None
Last Answer : b. Spherical shell
Description : Which of the following laminas have same moment of inertia (Ixx = Iyy), when passed through the centroid along x-x and y-y axes? a. Circle b. Semi-circle c. Right angle triangle d. Isosceles triangle
Last Answer : a. Circle
Description : Moment of inertia acting on a semi-circle about symmetrical axes is given as _______ a. 1.57 r4 b. 0.055 r4 c. 0.392 r4 d. 0.11 r4
Last Answer : c. 0.392 r4
Description : A leaf spring consists of 3 extra full length leaves and 14 graduated length leaves. The maximum force that can act on the spring is 70kN and the distance between eyes of the spring is 1.2m. Width and thickness of the ... close the nip. (a) 4332.2N (b) 4674.1N (c) 4985.4N (d) Can't be determined
Last Answer : (b) 4674.1N
Description : A leaf spring consists of 3 extra full length leaves and 14 graduated length leaves. The maximum force that can act on the spring is 70kN and the distance between eyes of the spring is 1.2m. Width and thickness of the ... /mm², calculate the initial nip. (a) 26.8mm (b) 24.9mm (c) 22.5mm (d)23.1mm
Last Answer : b) 24.9mm
Description : The type of spring used to achieve any linear and non-linear load-deflection characteristics is (a)spiral spring (b) non-ferrous spring (c)Belleville spring (d) torsion spring
Last Answer : (c)Belleville spring
Description : The type of spring used to achieve greater load carrying capacity within given space is (a)spiral spring (b) springs in series (c)multi-leaf spring (d) concentric spring
Last Answer : (d) concentric spring
Description : With a leaf spring type of suspension, interference between steering and suspension system can be (a) front end of the spring is pin joined and the rear end is shackled (b) front end of the spring is ... joined (c) both end of the spring are shackled (d) both end of the spring are pin joined
Last Answer : (b) front end of the spring is shackled and the rear end is pin joined
Description : The type of stress induced in a closed coiled helical tension spring is a. tensile b. compressive c. torsional shear d. tensile and compressive
Last Answer : c. torsional shear
Description : Draw a neat of full floating rear axle. Label all the parts. State an application of Semi floating, three quarter floating and full floating rear axle.
Last Answer : Semi floating: light motor vehicle three quarter floating:light motor vehicle full floating rear axle: heavy commercial vehicles
Description : The clips placed at intervals along some leaf spring to prevent spring leaf separation on rebound are (a) rebound clips (b) separation clips (c) interval clips (d)relief clips
Last Answer : (a) rebound clips
Description : The device that permits variation in the distance between the spring eyes of a leaf spring as the spring flexes is called (a) Spring shackle (b) spring U bolt (c) spring hanger (d) spring leaf
Last Answer : (a) Spring shackle
Description : Leaf spring for vehicles are nipped to (a) To vary the effective length of the spring (b) to increase the interleaf friction (c) Improve the load carrying capacity of spring (d) ensure that all leaves are uniformly stressed during loading
Last Answer : (d) ensure that all leaves are uniformly stressed during loading
Description : The weight or pressure required to deflect a spring in mm is called the spring (a) Weight (b) deflection (c) rate (d) rebound
Last Answer : c) rate
Description : There are number of laminations in a (a) Close coiled spring (b) Open coiled spring (c) Spiral spring (d) None
Description : Most important features of any spring are (a) Deflection, stiffness and strength (b) Stiffness, bending and shear strengths (c) Strain energy, deflection and strength (d) None
Last Answer : (c) Strain energy, deflection and strength
Description : Spiral spring is quite rigid. (a) Yes (b) No it is flexible (c) It is of moderate rigidity (d) Rigidity can’t be determined
Last Answer : (b) No it is flexible
Description : What will happen if stresses induced due to surge in the spring exceeds the endurance limit stress of the spring. (a) Fatigue Failure (b) Fracture (c) None of the listed (d) Nipping
Last Answer : (a) Fatigue Failure
Description : A concentric spring consists of 2 sprigs of diameter 10mm and 4mm. The net force acting on the composite spring is 5000N. Find the force acting on each of the two springs. (a) 1232.2N and 3767.8N (b) 786.4N and 4213.6N (c) 689.7N and 4310.3N (d) 645.3N and 4354.7N
Last Answer : (c) 689.7N and 4310.3N
Description : The strain energy stored in a spiral spring is given by? (a) 12M²L/Ebtᵌ (b) 6M²L/Ebtᵌ (c) 8M²L/Ebtᵌ (d) None of the listed
Last Answer : (b) 6M²L/Ebtᵌ
Description : Belleville spring can only produce linear load deflection characteristics. (a) Only linear (b) Linear as well as non linear (c) Non-linear (d) None of the mentioned
Last Answer : (b) Linear as well as non linear
Description : Spring shackles are used to join (a) chassis frame and spring (b) Spring and Axle (c) chassis frame and axle (d) all of the above
Last Answer : (a) chassis frame and spring
Description : Shackles are sort of (a) coupling (b) link (c) spring (d) none of the above
Last Answer : (b) link
Description : The spring used in mechanical toys is (a) Leaf spring (b) Spiral spring (c) Helical spring (d) All of these
Last Answer : (b) Spiral spring
Description : A spring used to absorb shocks and vibrations is (a) Close-coil helical spring (b) Open coiled helical spring (c) Spiral spring (d) Leaf spring
Last Answer : (d) Leaf spring
Description : In a watch, the spring is used to store energy. The energy is released (a) To stop the watch (b) To run the watch (c) To change the time (d) All of these (
Last Answer : (b) To run the watch
Description : The most important property for the spring material is (a) High elastic limit (b) High deflection value (c) Resistance to fatigue and shock (d) All of these
Last Answer : (d) All of these
Description : In spring balances, the spring is used (a) To apply forces (b) To absorb shocks (c) To store strain energy (d) To measure forces
Last Answer : (d) To measure forces
Description : The load required to produce a unit deflection in the spring is called (a) Modulus of Rigidity (b) Spring stiffness (c) Flexural rigidity (d) Tensional rigidity
Last Answer : b) Spring stiffness
Description : Deflection in a spring should be (a) Large (b) Small (c) Zero (d) None
Last Answer : (a) Large
Description : Strain energy in a spring should be (a) Large (b) Small (c) Zero (d) None
Description : Spring is an (a) Elastic device (b) Plastic device (c) Elastic as well as plastic device (d) None
Last Answer : (a) Elastic device
Description : Strain energy in a leaf spring is (a) W x δ (b) W x δ/3 (c) W x δ/2 (d) None
Last Answer : (c) W x δ/2
Description : Overlap in a leaf spring is (a) L/n (b) L/2n (c) L/3n (d) None
Last Answer : (b) L/2n
Description : Maximum deflection in a leaf spring is given by (a) 3WL3/4Enbt3 (b) 3WL3/8Enbt3 (c) 3WL3/16Enbt3 (d) None
Last Answer : (b) 3WL3/8Enbt3
Description : Maximum bending stress in a leaf spring is (a) 3WL/4nbt2(b) 3WL/8nbt2(c) 3WL/2nbt2(d) None
Last Answer : (c) 3WL/2nbt2
Description : A spring of stiffness 100 N/mm used in a spring-loaded safety valve of diameter 20 mm on a boiler with the pressure inside the boiler equal to 1 MPa should be initially compressed by a. 5mm b. 3.14 mm c. 2mm d. 6.28 mm
Last Answer : b. 3.14 mm
Description : A spring with 25 active coils cannot be accommodated within a given space. Hence 5 coils of the spring are cut. The stiffness of the new spring will be a. the same b. 1.25 times the original spring c. 0.8 times the original spring d. 20 times the original spring
Last Answer : b. 1.25 times the original spring
Description : Initial gap between two turns of a close coil helical tension spring should be a. 0.5 mm b. based on the maximum deflection c. 1 mm d. zero
Last Answer : d. zero