Description : When the helical torsion spring is subjected to torque, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress
Last Answer : (C) Bending stress
Description : When the helical compression spring is subjected to axial compressive force, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress
Last Answer : (D) Torsional shear stress
Description : When the helical extension spring is subjected to axial tensile force, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress
Description : A close coiled helical spring is compressed. Its wire is subjected to A. Compression B. Tension C.Shear D. Torque
Last Answer : B. Tension
Description : Shear stress in a close coiled helical spring is (a) 16WD/π d3 (b) 32WD/π d3 (c) 8WD/π d3 (d) None
Last Answer : (c) 8WD/π d3
Description : When a bar is subjected to increase in temperature and its deformation is prevented, the stress induced in the bar is (a) Tensile (b) Compressive (c) Shear (d) None of the above
Last Answer : (b) Compressive
Description : When a bar is subjected to a change of temperature and its longitudinal deformation is prevented, the stress induced in the bar is (a) Tensile (b) Compressive (c) Shear (d) Temperature
Last Answer : (d) Temperature
Description : When a close-coiled helical spring is subjected to an axial load, it is said to be under. (a) Bending (b) Shear (c) Torsion (d) Crushing
Last Answer : (c) Torsion
Description : A close coiled spring under axial load produces (a) Bending stresses (b) Shear stresses (c) Tensile stresses (d) None
Last Answer : (b) Shear stresses
Description : A closed helical spring under axial torque is designed on the basis of (a) Shear (b) Compression (c) Bending (d) None
Last Answer : (c) Bending
Description : A closed helical spring under axial load is designed on the basis of (a) Shear (b) Compression (c) Bending (d) None
Last Answer : (a) Shear
Description : A thin spherical shell under internal pressure will fail under a. Maximum shear stress b. Principal compressive stress c. Principal tensile stress d. None
Last Answer : c. Principal tensile stress
Description : When a shaft is subjected to a twisting moment, every cross-section of the shaft will be under (a) Tensile stress (b) Compressive stress (c) Shear stress (d) All of these
Last Answer : c) Shear stress
Description : A spring used to absorb shocks and vibrations is (a) Close-coil helical spring (b) Open coiled helical spring (c) Spiral spring (d) Leaf spring
Last Answer : (d) Leaf spring
Description : Strain energy in a close coiled helical spring is (a) τ2/8G (b) τ2/16G (c) τ2/4G (d) None
Last Answer : (c) τ2/4G
Description : Deflection in a close coiled helical spring is (a) 16 WR3n/Gd4 (b) 32 WR3n/Gd4 (c) 64 WR3n/Gd4 (d) None
Last Answer : (c) 64 WR3n/Gd4
Description : If a close-coiled helical spring absorbs 50 N-mm of energy while extending by 5 mm, its stiffness will be (a) 2 N/mm (b) 4 N/mm (c) 6 N/mm (d) 10 N/mm
Last Answer : (d) 10 N/mm
Description : A close-coiled helical spring of stiffness 30 N/mm is arranged in series with another such spring of stiffness 60 N/mm. The stiffness of composite unit is (a) 20 N/mm (b) 30 N/mm (c) 45 N/mm (d) 90 N/mm
Last Answer : (a) 20 N/mm
Description : Two close-coiled helical springs are equal in all respects except the number of turns. If the number of turns are in the ratio of 2:3, then the stiffness of the spring will be in the ratio of (a) 2:3 (b) 4:9 (c) 3:2 (d) 9:4
Last Answer : (c) 3:2
Description : A close –coiled helical spring is cut into two equal parts. The stiffness of the resulting springs will be (a) same (b) double (c) half (d) One-fourth
Last Answer : (b) double
Description : The close-coiled helical springs ‘A’ and ‘B’ are of same material, same coil diameter, same wire diameter and subjected to same load. If the number of turns of spring ‘A’ is half that of spring ‘B’, the ratio of deflection of spring ‘A’ to spring ‘B’ is (a)1/2 (b) 1 (c) 2 (d) 4
Last Answer : (a)1/2
Last Answer : d) Leaf spring
Description : When two helical springs of equal lengths are arranged to form a cluster spring, then a. Shear stress in each spring will be equal b. Load taken by each spring will be half the total load c. Only A is correct d. Both A and B is correct
Last Answer : d. Both A and B is correct
Description : Find the shear stress in the spring wire used to design a helical compression sprig if a load of 1200N is applied on the spring. Spring index is 6, and wire diameter 7mm. a) 452.2N/mm² b) 468.6N/mm² c) 512.2N/mm² d) None of the listed
Last Answer : b) 468.6N/mm²
Description : The spokes of the flywheel are subjected to 1. direct shear stress 2. torsional shear stress 3. tensile stress 4. compressive stress
Last Answer : 3. tensile stress
Description : The rim of the flywheel is subjected to, 1. direct tensile stress and bending stress 2. torsional shear stress and bending stress 3. direct shear stress and bending stress 4. compressive stress and bending stress
Last Answer : 1. direct tensile stress and bending stress
Description : The spokes of the flywheel are subjected to, (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress
Last Answer : (C) Tensile stress
Description : When a nut is tightened by placing a washer below it, the threads of bolt are subjected to (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress
Last Answer : (A) Direct shear stress
Description : While designing screw threads, adequate length of engaged threads between the screw and nut is provided so as to prevent failure of threads due to (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress
Description : When a nut is tightened by placing a washer below it, the shank of bolt is subjected to (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress
Description : Torsional shear stresses are induced in the spring wire when (A) spring is under compression (B) spring is under tension (C) both (A) and (B) (D) none of the above
Last Answer : (C) both (A) and (B)
Description : Wahl’s stress concentration factor is used in close coiled springs under axial load to account for (a) Shear effect (b) Bending effect (c) Compression effect (d) none
Last Answer : (b) Bending effect
Description : A power transmitting ductile material shaft under P, T and M will fail under (a) Tensile considerations only (b) Compressive considerations only (c) Shear considerations only (d) None
Last Answer : (c) Shear considerations only
Description : It is a secondary shaft used to counter the direction of main shaft. 81. Shafts are subjected to ______ forces. a) Compressive b) Tensile c) Shear d) twisting
Last Answer : b) Tensile
Description : When a body is subjected to transverse vibrations, the stress induced in a body will be A Shear stress B Bending stress C Tensile stress D Compressive stress
Last Answer : B Bending stress
Description : When a body is subjected to transverse vibrations, the stress induced in a body B will be (A) Shear stress (B) Bending stress (C) Tensile stress (D)Compressive stress
Last Answer : (B) Bending stress
Description : When a body is subjected to transverse vibrations, the stress induced in a body will be a) shear stress b) bending stress c) tensile stress d) compressive stress
Last Answer : b) bending stress
Description : When a body is subjected to transverse vibrations, the stress induced in a body will be a) shear stress b) tensile stress c) compressive stress d) none of the mentioned
Last Answer : b) tensile stress
Description : Initial gap between two turns of a close coil helical tension spring should be a. 0.5 mm b. based on the maximum deflection c. 1 mm d. zero
Last Answer : d. zero
Description : A open helical spring under axial torque is designed on the basis of (a) Shear (b) Compression (c) Bending (d) None
Last Answer : d) None
Description : Which factor is used to consider the effects of direct shear stress and torsional shear stress when curvature effect stress is not considered? a. Shear stress concentration factor b. Wahl shear stress concentration factor c. Both a. and b. d. None of the above
Last Answer : a. Shear stress concentration factor
Description : A hollow prismatic beam of circular section is subjected to a torsional moment. The maximum shear stress occurs at (a) inner wall of cross section (b) middle of thickness (c) outer surface of shaft (d) none of these
Last Answer : (c) outer surface of shaft
Description : Strength of a shaft a. Is equal to maximum shear stress in the shaft at the time of elastic failure b. Is equal to maximum shear stress in the shaft at the time of rupture c. Is equal to torsional rigidity d. Is ability to resist maximum twisting moment
Last Answer : d. Is ability to resist maximum twisting moment
Description : For two shafts joined in parallel, the --------------- in each shaft is same. a. shear stress. b. Angle of twist c. torque d. torsional stress.
Last Answer : b. Angle of twist
Description : For two shafts joined in series, the --------------- in each shaft is same. a. shear stress. b. Angle of twist c. torque d. torsional stress.
Last Answer : c. torque
Description : Maximum shear stress in a hollow shaft subjected to a torsional moment is at the a. Middle of thickness. b. At the inner surface of the shaft. c. At the outer surface of the shaft. d. At the middle surface of the shaft.
Last Answer : c. At the outer surface of the shaft.
Description : The region of the cross-section of a column in which compressive load may be applied without producing any tensile stress, is known as the core of the cross-section. In circular columns the radius of the core, ... One-third of the radius (c) One-quarter of the radius (d) One-fifth of the radius
Last Answer : (c) One-quarter of the radius
Description : In a simply supported beam loaded with U.D.L over the whole section, the bending stress is …………. at top and ………….. at bottom. (a) Compressive, tensile (b) Tensile, compressive (c) Tensile, zero (d) Compressive, zero
Last Answer : (a) Compressive, tensile
Description : A helical spring is fabricated by wrapping wire 19.05 mm in diameter around a forming cylinder 203.2 mm in diameter. Compute the number of turns required to permit an elongation of 101.6 mm. without exceeding a shearing ... G = 82737 N/mm2. a. 10 turns b. 20 turns c. 25 turns d. 30 turns
Last Answer : a. 10 turns