A fuse is placed in series with the cireuit to protect against a. high power b. high voltage c. high current d. over heating

A fuse is placed in series with the cireuit to protect against
a. high power b. high voltage
c. high current d. over heating
by

1 Answer

Answer :

d. over heating
by

Related questions

A conductor of length L has current I passing through it, when it is placed parallel to a magnetic field. The force experienced by the conductor will be (a) zero (b) BLI (c) B2LI (d) BLI2

Description : A conductor of length L has current I passing through it, when it is placed parallel to a magnetic field. The force experienced by the conductor will be (a) zero (b) BLI (c) B2LI (d) BLI2

Last Answer : (a) zero

What is the function of a fuse?

Description : What is the function of a fuse?

Last Answer : Fuse places a limit on the amount of current that can be drawn by an electric circuit by opening (blowing or melting) when the current exceeds a preset limit. This protects the circuit and the surroundings from fire or damage in the case of an overload or short circuit.

Capacity of battery fuse in AC Coaches a. 315 A & 400 (HRC ) c. 16 A (HRC ) b. 63 A (HRC ) d. 5 A (HRC )

Description : Capacity of battery fuse in AC Coaches a. 315 A & 400 (HRC ) c. 16 A (HRC ) b. 63 A (HRC ) d. 5 A (HRC )

Last Answer : a. 315 A & 400 (HRC )

Why should a resistance be introduced in a circuit in series deliberately? a. to increase current b. to decrease current c. to control current d. just to give a good look to circuit

Description : Why should a resistance be introduced in a circuit in series deliberately? a. to increase current b. to decrease current c. to control current d. just to give a good look to circuit

Last Answer : b. to decrease current

What is a current transformer and voltage transformer?*

Description : What is a current transformer and voltage transformer?*

Last Answer : In electrical engineering, a current transformer (CT) is used for measurement of electric currents. Current transformers, together with voltage transformers (VT) (potential transformers (PT)), ... transformers are commonly used in metering and protective relays in the electrical power industry.

The output from a full wave rectifier is (a) A pulsating uni-directional current (b) A DC voltage (c) Zero (d) An AC voltage

Description : The output from a full wave rectifier is (a) A pulsating uni-directional current (b) A DC voltage (c) Zero (d) An AC voltage

Last Answer : a) A pulsating uni-directional current

The claddingwhichsurroundsthe fiber core a. is used to reduce optical interference b. is used to protect the fiber c. acts to help guide the light in the core d. ensures that the refractive index remains constant

Description : The claddingwhichsurroundsthe fiber core a. is used to reduce optical interference b. is used to protect the fiber c. acts to help guide the light in the core d. ensures that the refractive index remains constant

Last Answer : c. acts to help guide the light in the core

A circuit breaker is designed to protect an electrical circuit from damage caused by :

Description : A circuit breaker is designed to protect an electrical circuit from damage caused by :  (A) Over load (B) Short circuit (C) Over current (D) All of the above

Last Answer : A circuit breaker is designed to protect an electrical circuit from damage caused by :  (A) Over load (B) Short circuit (C) Over current (D) All of the above

When an iron piece is placed in a magnetic field (a) the magnetic lines of force will bend away from their usual paths in order to go away from the piece (b) the magnetic lines of force will bend away from their usual paths in order to pass through the piece (c) the magnetic field will not be affected (d) the iron piece will break

Description : When an iron piece is placed in a magnetic field (a) the magnetic lines of force will bend away from their usual paths in order to go away from the piece (b) the magnetic lines of force will bend ... to pass through the piece (c) the magnetic field will not be affected (d) the iron piece will break

Last Answer : (b) the magnetic lines of force will bend away from their usual paths in order to pass through the piece

The termssinglemode andmultimode are bestdescribes as a. the number of fibers placed into a fiber-optic cable b. the number of voice channels each fiber can support c.thenumber ofwavelengths eachfiber cansupport d. the index number

Description : The termssinglemode andmultimode are bestdescribes as a. the number of fibers placed into a fiber-optic cable b. the number of voice channels each fiber can support c.thenumber ofwavelengths eachfiber cansupport d. the index number

Last Answer : c.thenumber ofwavelengths eachfiber cansupport

A magnetic screw placed in a non-uniform magnetic field experiences a) force and torque b) only torque c) only force d) None of these

Description : A magnetic screw placed in a non-uniform magnetic field experiences a) force and torque b) only torque c) only force d) None of these

Last Answer : a) force and torque

In case of two identical charges placed at certain distance, the electric lines of force are: (a) Curved (b) Straight lines (c) Both (a) and (b) (d) None of these

Description : In case of two identical charges placed at certain distance, the electric lines of force are: (a) Curved (b) Straight lines (c) Both (a) and (b) (d) None of these

Last Answer : a) Curved

The electric force between two charges placed in air is 2 Newton. When placed in a medium of ∈r = 80, the force reduced to: (a) 0.029 N (b) 0.025 N (c) 0.03 N (d) 0.04 N

Description : The electric force between two charges placed in air is 2 Newton. When placed in a medium of ∈r = 80, the force reduced to: (a) 0.029 N (b) 0.025 N (c) 0.03 N (d) 0.04 N

Last Answer : (b) 0.025 N

Three equal resistors connected in series with a source of e m f together dissipate 10 W of power each. What will be the power dissipated if the same resistors are connected in parallel across the same source of e m f? a. 40 W b. 90W c. 100W d. 120W

Description : Three equal resistors connected in series with a source of e m f together dissipate 10 W of power each. What will be the power dissipated if the same resistors are connected in parallel across the same source of e m f? a. 40 W b. 90W c. 100W d. 120W

Last Answer : b. 90W

How is the protection against reverse power given?

Description : How is the protection against reverse power given?

Last Answer : Reverse power protection is used for anti-motoring. This function is used for protection of prime mover not generator. It can cut-off the fuel supply and stop the prime mover.

A galvanometer having a resistance of 4.5 Ω can read up to 5 mA. If it is to read 100 V, then the high resistance to be used in series will be a) 19998 Ω b) 19995.8 Ω c) 19995.5 Ω d) 19996.5 Ω

Description : A galvanometer having a resistance of 4.5 Ω can read up to 5 mA. If it is to read 100 V, then the high resistance to be used in series will be a) 19998 Ω b) 19995.8 Ω c) 19995.5 Ω d) 19996.5 Ω

Last Answer : c) 19995.5

Desirable resistance of a ________ is achieved by connecting a high resistance Rh in series with a galvanometer a) Ammeter b) Ohmmeter c) LED d) Voltmeter

Description : Desirable resistance of a ________ is achieved by connecting a high resistance Rh in series with a galvanometer a) Ammeter b) Ohmmeter c) LED d) Voltmeter

Last Answer : d) Voltmeter

How do you test reverse power trip, high current trip, preferential trip?

Description : How do you test reverse power trip, high current trip, preferential trip?

Last Answer : Reverse power trip - refer answer for question 11. Also ask E/O. High current (over load trip) - Set your overload relay high current trip setting to say 75% of the rated current. Run the ... loads to overload the generator. Preferential trip will trip all the non-critical loads. Also ask E/O.

Process of conversion low voltage to high voltage is called _______ (a) Rectification (b)forward bias (c) reverse bias (d) amplification

Description : Process of conversion low voltage to high voltage is called _______ (a) Rectification (b)forward bias (c) reverse bias (d) amplification

Last Answer : (d) amplification

Why is it cheaper to transmit electrical energy at high voltage?

Description : Why is it cheaper to transmit electrical energy at high voltage?

Last Answer : Because of the electrical energy was step upped by transformers the transformer have high efficiency than the electric energy is cheaper

Using a fuse whose rating is higher than necessary ________. A. endangers the apparatus it is supposed to protect B. reduces the possibility of short circuits C. increases the efficiency of the equipment by allowing more current to be used D. wastes money because they are more expensive

Description : Using a fuse whose rating is higher than necessary ________. A. endangers the apparatus it is supposed to protect B. reduces the possibility of short circuits C. increases the efficiency of the equipment by allowing more current to be used D. wastes money because they are more expensive

Last Answer : Answer: A

To protect wiring from excessive passing of current is A. voltmeter B. fuse C. galvanometer D. resistanc

Description : To protect wiring from excessive passing of current is A. voltmeter B. fuse C. galvanometer D. resistanc

Last Answer : fuse

When troubleshooting a motor controller, all indications are that a relay coil should be energized. If there were no magnetic pull, with rated voltage measured across the coil, the most probable cause would be that the _________________. A. coil is open B. control fuse is open C. auxiliary contact in series with the coil is defective D. relay armature is stuck

Description : When troubleshooting a motor controller, all indications are that a relay coil should be energized. If there were no magnetic pull, with rated voltage measured across the coil, the most probable cause ... open C. auxiliary contact in series with the coil is defective D. relay armature is stuck

Last Answer : Answer: A

In the illustration, the diode between terminals 16 and 17 is to _________. EL-0046 A. insure that the voltage across the governor coil (EG-3P) never exceeds .6 VDC B. compensate for the temperature difference of the governor oil heating up C. protect the electronic governor from counter EMF D. act as a filter to prevent hunting

Description : In the illustration, the diode between terminals 16 and 17 is to _________. EL-0046 A. insure that the voltage across the governor coil (EG-3P) never exceeds .6 VDC B. compensate for the ... heating up C. protect the electronic governor from counter EMF D. act as a filter to prevent hunting

Last Answer : Answer: C

The most inefficient method of voltage reduction, from the standpoint of power loss, even when placed in series with the load, is the use of a/an ____________. A. capacitor B. inductor C. resistor D. transistor

Description : The most inefficient method of voltage reduction, from the standpoint of power loss, even when placed in series with the load, is the use of a/an ____________. A. capacitor B. inductor C. resistor D. transistor

Last Answer : Answer: C

Moving coil in dynamometer wattmeter connected a) In series with fixed coil b) Across supply c) In series with load d) Across load

Description : Moving coil in dynamometer wattmeter connected a) In series with fixed coil b) Across supply c) In series with load d) Across load

Last Answer : Ans: Across supply

Which series lies in the Ultraviolet region? a) Lyman series b) Paschen series c) Brackett serie d) Balmer series

Description : Which series lies in the Ultraviolet region? a) Lyman series b) Paschen series c) Brackett serie d) Balmer series

Last Answer : a) Lyman series

Three spectral series, paschen series, Brackett series, Pfund series are found in the a) ultraviolet region b) visible region c) infrared region d) a & b region

Description : Three spectral series, paschen series, Brackett series, Pfund series are found in the a) ultraviolet region b) visible region c) infrared region d) a & b region

Last Answer : c) infrared region

The region where the Lyman series contains the wavelength 1∕ λ = RH [1/ 12 – 1/ n2 ] is a) visible region b) infrared region c) ultraviolet region d ) none of these

Description : The region where the Lyman series contains the wavelength 1∕ λ = RH [1/ 12 – 1/ n2 ] is a) visible region b) infrared region c) ultraviolet region d ) none of these

Last Answer : c) ultraviolet region

The only series which lies in the visible region of the electromagnetic spectrum is a) Paschen series b) Lyman series c) Balmer series d) Pfund series

Description : The only series which lies in the visible region of the electromagnetic spectrum is a) Paschen series b) Lyman series c) Balmer series d) Pfund series

Last Answer : b) Lyman series

The first Hydrogen spectral series was identified , in 1885, by a) J.R.Rydberg b) J.J.Balmer c) Theodore Lyman d) F. S. Brackett

Description : The first Hydrogen spectral series was identified , in 1885, by a) J.R.Rydberg b) J.J.Balmer c) Theodore Lyman d) F. S. Brackett

Last Answer : b) J.J.Balmer

Three bulbs are rating 40W 60W and 100W designed to work on 220V mains. Which bulb will burn most brightly if they are connected in series across 220 V mains? a. 40 W bulb b. 60 W blub c. 100 W blub d. all will burn equally brightly

Description : Three bulbs are rating 40W 60W and 100W designed to work on 220V mains. Which bulb will burn most brightly if they are connected in series across 220 V mains? a. 40 W bulb b. 60 W blub c. 100 W blub d. all will burn equally brightly

Last Answer : a. 40 W bulb

What is the function of a fuse wire? (a) To prevent an unduly high electric current from passing through a circuit (b) To increase the current supply (c) To decrease the current supply (d) To stabilise the voltage

Description : What is the function of a fuse wire? (a) To prevent an unduly high electric current from passing through a circuit (b) To increase the current supply (c) To decrease the current supply (d) To stabilise the voltage

Last Answer : Ans:(a)

A thermal protection switch can protect against (a) short-circuit (b) temperature (c) overload (d) over voltage

Description : A thermal protection switch can protect against (a) short-circuit (b) temperature (c) overload (d) over voltage

Last Answer : (c) overload

The termresponsivityasit appliesto a light detectorisbest described as a. the time required for the signal to go from 10 to 90 percent of maximum amplitude b.the ratio ofthediode output currentto opticalinputpower c. the ratio of output current to output power d. the ratio of output current to input current

Description : The termresponsivityasit appliesto a light detectorisbest described as a. the time required for the signal to go from 10 to 90 percent of maximum amplitude b.the ratio ofthediode output currentto ... of output current to output power d. the ratio of output current to input current

Last Answer : b.the ratio ofthediode output currentto opticalinputpower

Why is this reverse power used instead of reverse current in alternators?

Description : Why is this reverse power used instead of reverse current in alternators?

Last Answer : It is extremely difficult to detect reverse current with an alternating current system, reverse power can be detected and protection can be provided by reverse power relay.

When an alternating current passes through an ohmic resistance the electrical power converted into heat is?

Description : When an alternating current passes through an ohmic resistance the electrical power converted into heat is?

Last Answer : When an alternating current passes through an ohmic resistance the electrical power converted into heat is true power.

The purpose of a motor undervoltage protection device is to _____________. A. prevent high armature current when power is restored B. start the motor at a very low voltage C. trip the load off the motor in case of fire D. protect personnel from low voltage shocks

Description : The purpose of a motor undervoltage protection device is to _____________. A. prevent high armature current when power is restored B. start the motor at a very low voltage C. trip the load off the motor in case of fire D. protect personnel from low voltage shocks

Last Answer : Answer: A

What is the speaker driving voltage of an amplifier?

Description : What is the speaker driving voltage of an amplifier?

Last Answer : I have to ask WHY? That said, Speakers and a light bulb are two different types of load, and the the lights will probably fry the output transistor.

How is this voltage achieved?

Description : How is this voltage achieved?

Last Answer : By connecting 12 cells in series. 12 x 2 V = 24 V is total battery bank voltage.

What is the full battery voltage ?

Description : What is the full battery voltage ?

Last Answer : 24 V DC.

What is the voltage available from each cell in a lead acid battery?

Description : What is the voltage available from each cell in a lead acid battery?

Last Answer : 2 V DC.

What is safe voltage to prevent shock?

Description : What is safe voltage to prevent shock?

Last Answer : Normally 50V. It depends on the body resistance and how conducting the path is (example use of insulating boots or mat may allow slightly higher voltage to be safe)

What is the voltage used for ignition in boilers/incinerators etc.?

Description : What is the voltage used for ignition in boilers/incinerators etc.?

Last Answer : Normally 10,000V (10kV). But ask E/O to confirm.

What is the voltage?

Description : What is the voltage?

Last Answer : Ask E/O on your ship.

What is the voltage used in a meggar?

Description : What is the voltage used in a meggar?

Last Answer : 500V DC.

What is Under-voltage protection?

Description : What is Under-voltage protection?

Last Answer : It prevents closure of the breaker by mistake, or the generator that is coming on load during parallel operation. It also provides protection against loss of voltage while machinery is connected to the switchboard.

The wavelength of the wave associated with the moving object is a) Directly proportional to the accelerating voltage b) Directly proportional to the square of accelerating voltage c) Inversely proportional to the square root of accelerating voltage d) Inversely proportional to the accelerating voltage

Description : The wavelength of the wave associated with the moving object is a) Directly proportional to the accelerating voltage b) Directly proportional to the square of accelerating voltage c) ... proportional to the square root of accelerating voltage d) Inversely proportional to the accelerating voltage

Last Answer : c) Inversely proportional to the square root of accelerating voltage

Devices which convert various physical quantities into electrical voltage are known as (a) Control system (b) sensors (c) level sensors (d) LDR

Description : Devices which convert various physical quantities into electrical voltage are known as (a) Control system (b) sensors (c) level sensors (d) LDR

Last Answer : (b) sensors

A sensor which changes light intensity into electric voltage. (a) LDR (b) thermistor (c) photodiode (d) photovoltaic

Description : A sensor which changes light intensity into electric voltage. (a) LDR (b) thermistor (c) photodiode (d) photovoltaic

Last Answer : (a) LDR