How is the protection against reverse power given?

How is the protection against reverse power given?
by

1 Answer

Answer :

Reverse power protection is used for anti-motoring. This function is used for protection of prime mover not generator. It can cut-off the fuel supply and stop the prime mover.
by

Related questions

How do you test reverse power trip, high current trip, preferential trip?

Description : How do you test reverse power trip, high current trip, preferential trip?

Last Answer : Reverse power trip - refer answer for question 11. Also ask E/O. High current (over load trip) - Set your overload relay high current trip setting to say 75% of the rated current. Run the ... loads to overload the generator. Preferential trip will trip all the non-critical loads. Also ask E/O.

Why is this reverse power used instead of reverse current in alternators?

Description : Why is this reverse power used instead of reverse current in alternators?

Last Answer : It is extremely difficult to detect reverse current with an alternating current system, reverse power can be detected and protection can be provided by reverse power relay.

How do you test reverse power trip?

Description : How do you test reverse power trip?

Last Answer : When two generators are running in parallel and one generator can carry the load, reverse power trip can be tested by load shifting using governor control. When the load has shifted sufficiently and the off ... (using the test push button on the relay) to see if it initiates a trip signal.

What is the harm if reverse power flows?

Description : What is the harm if reverse power flows?

Last Answer : Assume that the generator normally produces an amount of power equal to P, and that when operating as a motor, it will absorb a similar amount, P. Therefore, the net effect on the grid will ... change on the grid. There could be prime mover damage in some instances (especially steam turbines).

When does Reverse power flow?

Description : When does Reverse power flow?

Last Answer : Situation of a generator is feeding a system through switchgear having several generators connected in parallel with this generator. The flow of current, when the system is running normally, is from the ... minor to extreme in the event of a complete mechanical failure of the generator which fails.

The reverse process of photo-electric effect is called: a) Annihilation of matter b) Compton effect c) Pair production d) X-rays

Description : The reverse process of photo-electric effect is called: a) Annihilation of matter b) Compton effect c) Pair production d) X-rays

Last Answer : d) X-rays

In the reverse biased p-n junction, the current is of the order of (a) Ampere (b) Milliampere (c) Microampere (d) Nano-ampere

Description : In the reverse biased p-n junction, the current is of the order of (a) Ampere (b) Milliampere (c) Microampere (d) Nano-ampere

Last Answer : (d) Nano-ampere

On increasing the reverse bias to a large value in a p-n junction diode current (a) Increases slowly (b) Remains fixed (c) Suddenly increases (d) Decreases slowly

Description : On increasing the reverse bias to a large value in a p-n junction diode current (a) Increases slowly (b) Remains fixed (c) Suddenly increases (d) Decreases slowly

Last Answer : (c) Suddenly increases

The reverse current through semiconductor diode is due to (a) Minority carrier (b) majority carrier (c) electrons (d) holes

Description : The reverse current through semiconductor diode is due to (a) Minority carrier (b) majority carrier (c) electrons (d) holes

Last Answer : (a) Minority carrier

Depletion region of a junction is formed _________ (a) during the manufacturing process (b) under forward bias (c) under reverse bias (d) when temperature varies

Description : Depletion region of a junction is formed _________ (a) during the manufacturing process (b) under forward bias (c) under reverse bias (d) when temperature varies

Last Answer : (a) during the manufacturing process

The potential difference set up across the depletion region is called (a) Absolute potential (b) neutral potential (c) reverse potential (d) potential barrier

Description : The potential difference set up across the depletion region is called (a) Absolute potential (b) neutral potential (c) reverse potential (d) potential barrier

Last Answer : (d) potential barrier

For normal operation of a transistor, the collector base junction is kept (a) Unbiased (b) forward biased (c) reverse biased (d) none

Description : For normal operation of a transistor, the collector base junction is kept (a) Unbiased (b) forward biased (c) reverse biased (d) none

Last Answer : (c) reverse biased

Process of conversion low voltage to high voltage is called _______ (a) Rectification (b)forward bias (c) reverse bias (d) amplification

Description : Process of conversion low voltage to high voltage is called _______ (a) Rectification (b)forward bias (c) reverse bias (d) amplification

Last Answer : (d) amplification

How is protection provided for OL and SC?

Description : How is protection provided for OL and SC?

Last Answer : Damage from short circuits and overloads can be reduced or prevented by employing fuses, circuiDamage from short circuits and overloads can be reduced or prevented by employing fuses, circuit breakers, or other overload ... (a few seconds) due to currents say 1.1 to 1.5 times the normal current.

What is Under-voltage protection?

Description : What is Under-voltage protection?

Last Answer : It prevents closure of the breaker by mistake, or the generator that is coming on load during parallel operation. It also provides protection against loss of voltage while machinery is connected to the switchboard.

A fuse is placed in series with the cireuit to protect against a. high power b. high voltage c. high current d. over heating

Description : A fuse is placed in series with the cireuit to protect against a. high power b. high voltage c. high current d. over heating

Last Answer : d. over heating

H.R.C. fuses provide best protection against (a) overload (b) reverse current (c) open-circuits (d) short-circuits

Description : H.R.C. fuses provide best protection against (a) overload (b) reverse current (c) open-circuits (d) short-circuits

Last Answer : (d) short-circuits

One ofthe followingis not a reason forthe use of anantenna coupler: a. To make the antenna look resistive b. To provide the output amplifier with the correct load impedance c. To discriminate against harmonics d. To prevent reradiation of the local oscillator

Description : One ofthe followingis not a reason forthe use of anantenna coupler: a. To make the antenna look resistive b. To provide the output amplifier with the correct load impedance c. To discriminate against harmonics d. To prevent reradiation of the local oscillator

Last Answer : d. To prevent reradiation of the local oscillator

Where automatic restart does not present a hazard after a power failure, Coast Guard Regulations (46 CFR) require motor controllers for auxiliaries vital to the propelling equipment to be provided with ________________. A. overload protection B. low voltage protection C. low voltage release D. reverse current protection

Description : Where automatic restart does not present a hazard after a power failure, Coast Guard Regulations (46 CFR) require motor controllers for auxiliaries vital to the propelling equipment to be provided ... overload protection B. low voltage protection C. low voltage release D. reverse current protection

Last Answer : Answer: C

Why are motor ratings given in KW and that of alternator and transformer given in KVA?

Description : Why are motor ratings given in KW and that of alternator and transformer given in KVA?

Last Answer : kW is the output mechanical power of a motor and is expressed in kW. kVA is the net (apparent) power input to the transformer. This input power is the output + losses. kW = kVA x system power factor

The total energy of electron in the Bohr orbit is given by the formula, E = a) - ke2 /2r b) - ke2 /2r2 c) - k 2 e/2r d) - ke2 /r

Description : The total energy of electron in the Bohr orbit is given by the formula, E = a) - ke2 /2r b) - ke2 /2r2 c) - k 2 e/2r d) - ke2 /r

Last Answer : a) - ke2 /2r

The quantized Bohr orbit radius of electron in hydrogen atom is given by a) n2 r3 b) nr1 c) n2 r2 d) n2 r1

Description : The quantized Bohr orbit radius of electron in hydrogen atom is given by a) n2 r3 b) nr1 c) n2 r2 d) n2 r1

Last Answer : d) n2 r1

The speed of hydrogen electron in the nth orbit is given by vn = a) 2λke2 / nh b) 2πke2 / λh c) 2πke2 / nh d) 2πke2 / h

Description : The speed of hydrogen electron in the nth orbit is given by vn = a) 2λke2 / nh b) 2πke2 / λh c) 2πke2 / nh d) 2πke2 / h

Last Answer : c) 2πke2

The concept that particles can behave like waves was given by a) Compton b) De-Broglie c) G.P. Thomson d) Germer

Description : The concept that particles can behave like waves was given by a) Compton b) De-Broglie c) G.P. Thomson d) Germer

Last Answer : b) De-Broglie

The relativistic energy ‘E’ is equivalent to relativistic mass given by a) Ec2 b) 2 c E c) c E d) E c

Description : The relativistic energy ‘E’ is equivalent to relativistic mass given by a) Ec2 b) 2 c E c) c E d) E c

Last Answer : b) 2 c E

Shunt resistance Rs is given as a) Ig I−Ig Rg b) Ig I+Ig Rg c) I I−Ig Rg d) None of these

Description : Shunt resistance Rs is given as a) Ig I−Ig Rg b) Ig I+Ig Rg c) I I−Ig Rg d) None of these

Last Answer : a) Ig I−Ig Rg

The force in a medium of relative permitivity ∈r is given by: (a) F′ =F (b) F′ =∈r ∈ F r (c) F′ = ∈r . F (d) F′ =F ∈ ∈

Description : The force in a medium of relative permitivity ∈r is given by: (a) F′ =F (b) F′ =∈r ∈ F r (c) F′ = ∈r . F (d) F′ =F ∈ ∈

Last Answer : (a) F′ =F

How to tell if a power strip is burned out?

Description : How to tell if a power strip is burned out?

Last Answer : answer:Personally, I would either toss it, or down grade it to outdoor use only. I wouldn’t take a chance with it in the house. Yes, you can let it cool down, then test it again. But a failure is a failure. Does it have a reset button? What price range did you pay?

How can a solar array power source be bypassed when the batteries run low?

Description : How can a solar array power source be bypassed when the batteries run low?

Last Answer : Ah got it. If anyone else is interested, you need an “automatic transfer switch” – or get a manual one for that mad scientist charm.

Power Who Say ?

Last Answer : that At the rate Electron Flowing Become Work Done Is Or That At the rate Electricity Power Other In strength Transformed Is Him Electric Power Says.

Power Who Say ?

Last Answer : any Person Or Of the object Single In time Made Of work The amount Power Says.

Which is the most suitable power device for high frequency ( more 100 kHz) switching application? a) Power MOSFET b) BJT c) SCR d) UJT

Description : Which is the most suitable power device for high frequency ( more 100 kHz) switching application? a) Power MOSFET b) BJT c) SCR d) UJT

Last Answer : Ans: Power MOSFET

A modern power semiconductor device IGBT is combines the characteristics of a) BJT and MOSFET b) FCT and GTO c) SCR and MOSFET d) SCR and BJT

Description : A modern power semiconductor device IGBT is combines the characteristics of a) BJT and MOSFET b) FCT and GTO c) SCR and MOSFET d) SCR and BJT

Last Answer : Ans: BJT and MOSFET

Which ofthe followingcableswill have the highestlaunch power capability? a. 50/125/0.2 b. 85/125/0.275 c. 62.5/125/0.275 d. 100/140/0.3

Description : Which ofthe followingcableswill have the highestlaunch power capability? a. 50/125/0.2 b. 85/125/0.275 c. 62.5/125/0.275 d. 100/140/0.3

Last Answer : d. 100/140/0.3

The termresponsivityasit appliesto a light detectorisbest described as a. the time required for the signal to go from 10 to 90 percent of maximum amplitude b.the ratio ofthediode output currentto opticalinputpower c. the ratio of output current to output power d. the ratio of output current to input current

Description : The termresponsivityasit appliesto a light detectorisbest described as a. the time required for the signal to go from 10 to 90 percent of maximum amplitude b.the ratio ofthediode output currentto ... of output current to output power d. the ratio of output current to input current

Last Answer : b.the ratio ofthediode output currentto opticalinputpower

When connectorlosses,splice losses, and couplerlosses are added,whatisthe finallimitingfactor? a. Source power b. Fiber attenuation c. Connector and splice losses d. Detector sensitivity

Description : When connectorlosses,splice losses, and couplerlosses are added,whatisthe finallimitingfactor? a. Source power b. Fiber attenuation c. Connector and splice losses d. Detector sensitivity

Last Answer : d. Detector sensitivity

What is power factor? What are the ways to improve it?*

Description : What is power factor? What are the ways to improve it?*

Last Answer : Ration of true power and apparent power. Using capacitors and synchronous motors.

Where does reactive power go?

Description : Where does reactive power go?

Last Answer : Reactive power is not 'lost'. It is delivered to the motor where it sustains the electric field that enables the motor to convert the real power (electrical) into mechanical torque.

What is the benefit of improving power factor?

Description : What is the benefit of improving power factor?

Last Answer : Power factor close to 1 means for the same real power in kW, the load current is less and hence the I2R losses are less. The system efficiency is higher as the losses are lower. Improved voltage regulation is achieved.

What is the meaning of power factor?

Description : What is the meaning of power factor?

Last Answer : Power factor is the cosine of the angle between voltage and current waveform.

A body will behave as an “ideal black body” when it acts as: a) A perfect absorber b) A perfect radiator c) A body to have absorption power equal to one d) All of the above

Description : A body will behave as an “ideal black body” when it acts as: a) A perfect absorber b) A perfect radiator c) A body to have absorption power equal to one d) All of the above

Last Answer : d) All of the above

The emitter of a transistor is doped the heaviest because it: (a) Acts as a supplier of charge carriers (b) Dissipates maximum power c) has a large resistance (d) has a small resistance

Description : The emitter of a transistor is doped the heaviest because it: (a) Acts as a supplier of charge carriers (b) Dissipates maximum power c) has a large resistance (d) has a small resistance

Last Answer : (a) Acts as a supplier of charge carriers

The operational amplifier is _______ (a) High gain amplifier (b) high power amplifier (c)high resistance amplifier (d)low resistance amplifier

Description : The operational amplifier is _______ (a) High gain amplifier (b) high power amplifier (c)high resistance amplifier (d)low resistance amplifier

Last Answer : a) High gain amplifier

Electric power a. V×I b. W/t c. V 2 /I d. E2 /t

Description : Electric power a. V×I b. W/t c. V 2 /I d. E2 /t

Last Answer : . V×I

An immersion heater of 400 watts kept on for 5 hours will consume electrical power of a. 2KWh b. 20KWh c. 6KWh d. 12KWh

Description : An immersion heater of 400 watts kept on for 5 hours will consume electrical power of a. 2KWh b. 20KWh c. 6KWh d. 12KWh

Last Answer : a. 2KWh

Three equal resistors connected in series with a source of e m f together dissipate 10 W of power each. What will be the power dissipated if the same resistors are connected in parallel across the same source of e m f? a. 40 W b. 90W c. 100W d. 120W

Description : Three equal resistors connected in series with a source of e m f together dissipate 10 W of power each. What will be the power dissipated if the same resistors are connected in parallel across the same source of e m f? a. 40 W b. 90W c. 100W d. 120W

Last Answer : b. 90W

Refer to the circuit below . The power consumed by the element E is equal

Description : الرجوع إلى الدائرة أدناه. الطاقة التي يستهلكها العنصر E متساوية.

Last Answer : The power consumed the element E is equal to the  : P = V x I = 6V x 1 A = 6 W

Briefly explain how the power factor of an inductive circuit can be improved.

Description : Briefly explain how the power factor of an inductive circuit can be improved.

Last Answer : As we know that power factor should be corrected to ensure that the current supplied is cost friendly. Meaning the power factor should be around one but not greater than one(0.8-0.9) in a ... an inductive circuit due to the inductive reactance which oppose the change of current in the ac circuit. 

State the importance of electrical power in day to day life.

Description : State the importance of electrical power in day to day life. 

Last Answer : Importance of electrical power in day to day life: 1. Electrical energy is the basic necessity for domestic (residency), commercial, industrial, agriculture, consumers , transport (Electric ... agriculture products. iv) Running motors, furnaces of various kinds in industry, running locomotives 

Problems on electrical power and energy

Description : Problems on electrical power and energy

Last Answer : Problem on electrical power and energy 1 : https://youtu.be/ZvWHuMdmv9g Problem on electrical power and energy 2 : https://youtu.be/19IZMc6U2vs Problem on electrical power and energy 3 : https ... : https://youtu.be/iYqGIwA919A Problem on electrical power and energy : https://youtu.be/iWnWQz_mzHk