Description : A 10 farad capacitor is used in a circuit. The voltage difference between the plates of the capacitor is 20 volts. What is the magnitude of the charge on each of the capacitor's plates?
Last Answer : ANSWER: 200 COULOMBS
Description : A circuit has a source voltage of 100 volts and two 50-ohm resistors connected in series. If the reference point for this circuit is placed between the two resistors, what would be the voltage at the reference point?
Last Answer : 50 volts.
Description : A circuit is to be designed in which a capacitor must charge to 40 percent of the maximum charging voltage in 200 microseconds. The resistor to be used has a resistance of 40,000 ohms. What size capacitor must be used?
Last Answer : 0.1 microfarads 40% from the graph = 0.5
Description : What is the voltage drop across the resistor in an RC charging circuit when the charge on the capacitor is equal to the battery voltage?
Last Answer : Zero.
Description : At what instant does the greatest voltage appear across the resistor in a series RC circuit when the capacitor is charging?
Last Answer : At the instant of the initiation of the action.
Description : When the circuit shown in the illustration is operating correctly, the voltage at the reference electrode will be kept in the optimum range of ____________. EL-0090 A. 0.01 - 0.05 volt B. 0.80 - 0.85 volt C. 35 - 60 volts D. 100 - 115 volts
Last Answer : Answer: B
Description : What is the term for the number of times per second that tank circuit energy is either stored in the inductor or capacitor?
Last Answer : Natural frequency or resonant frequency (f r).
Description : In an a.c. circuit that contains both an inductor and a capacitor, what term is used for the difference between the individual reactances?
Last Answer : Resultant reactance.
Description : What would be the output of a negative clamper with a bias potential of −5 volts and an input voltage swing from +50 to −50 volts?
Last Answer : -5 volts.
Description : What is the average voltage (Eavg) Output of a full-wave rectifier with an output of 100 volts peak?
Last Answer : 63.7 volts.
Description : If the output of a half-wave rectifier is 50-volts peak, what is the average voltage
Last Answer : 15.9 volts.
Description : What is the average voltage (Eavg) output of a full-wave rectifier that has an output of 100 volts peak?
Last Answer : 63.6 volts.
Description : A tube has a transconductance of 800 mhos and a load resistor of 50 kohms. When control grid voltage varies by 6 volts, the plate voltage will vary by what amount?
Last Answer : 240 volts.
Description : If the mu of a tube is 85 and the signal at the control grid is 4 volts ac, the plate voltage will vary by what amount?
Last Answer : 340 volts.
Description : The plate voltage of a tube will vary 126 volts when a 3-volt ac signal is applied to the control grid. What is the gain of this tube?
Last Answer : 42.
Description : If the source voltage for the voltage divider in question 50 supplies 150 volts, what is the total current through the voltage divider?
Last Answer : 495 mA.
Description : Using the graph in figure 3-7, what is the approximate value of current when the voltage is 12.5 volts?
Last Answer : 1.25 amperes.
Description : If Eeff is 130 volts and Ieff is 3 amperes, what is the total resistance (RT) in the circuit?
Last Answer : 43.3 ohms.
Description : What effect does the capacitor have on a changing voltage?
Last Answer : The capacitor opposes any change in voltage.
Description : If the supply voltage is 220 volts 60 Hz, what is the operating voltage of the motor controller circuitry illustrated? EL-0011 A. 110 volts DC B. 110 volts AC C. 220 volts DC D. 220 volts AC
Last Answer : Answer: D
Description : When the capacitor is completely discharged, where is the energy of the tank circuit stored?
Last Answer : Inductor magnetic field
Description : What determines the rate of discharge of the capacitor in a filter circuit?
Last Answer : Value of capacitance and load resistance.
Description : . What determines the rate of discharge of the capacitor in a filter circuit?
Last Answer : Value of capacitance and load resistance
Description : In a circuit using grid-leak biasing, the coupling capacitor (Cc) chargcharge path?
Last Answer : rkg, the cathode to grid resistance.
Description : What is the RC time constant of a series RC circuit that contains a 12-megohm resistor and a 12-microfarad capacitor?
Last Answer : 144 seconds (t=R x C)
Description : state what happens to the electrons in a capacitor circuit when (a) the capacitor is charging and (b) the capacitor is discharging.
Last Answer : a. When the capacitor is charging, electrons accumulate on the negative plate and leave the positive plate until the charge on the capacitor is equal to the battery voltage. b. When the ... the negatively charged plate to the positively charged plate until the charge on each plate is neutral.
Description : If 450 volts AC were measured across the load as shown in the illustration it would indicate a/an _______________. EL-0083 A. open winding between 'H1' and 'X1' B. properly operating circuit C. open winding between 'X1' and 'X4' D. ground on one side of 'Ep'
Last Answer : Answer: C
Description : What is the term used to refer to the losses which can be traced to the dielectric of a capacitor?
Last Answer : Power losses.
Description : What is the term for the opposition that a capacitor presents to ac?
Last Answer : Capacitive reactance.
Description : When troubleshooting a console circuit card suspected of being faulty, first check operating voltages, clean the card and then _________________. A. make sure wired connections and push-on connectors ... circuit traces with an ohmmeter D. measure the gain of each transistor or integrated circuit
Last Answer : Answer: A
Description : A common-emitter circuit has an input voltage of 0.1 volt, an output voltage of 2.0 volts, an input current of 0.5 milliamps, and an output current of 10 milliamps. What is the power gain? A. 20 B. 40 C. 400 D. 4000
Description : If the voltage supplied to the lighting circuit is 110 volts, how much current is used by a 100 watt light bulb? A. 0.08 amps B. 0.91 amps C. 1.10 amps D. 90.9 amps
Description : A battery is connected to a circuit containing three resistors in parallel. The values of the three resistors are 2 ohms, 3 ohms, and 6 ohms. What is the voltage of the battery if the total circuit current is 12 amps? A. 2 volts B. 6 volts C. 12 volts D. 24 volt
Description : In the illustration, A, B, C, and D are 12 volts in the circuit. What is the voltage of the lead connected to C and D with respect to the lead connected to A and B? EL-0039 A. (-) 48 volts B. (+) 48 volts C. (-) 24 volts D. (+) 24 volts
Description : In the illustration, 12 volts is applied to the circuit where the resistance of R1 is 10 ohms and R2 is 10 ohms. what is the voltage across R2? EL-0036 A. 1.2 volts B. 2 volts C. 6 volts D. 12 volts
Description : In the illustrated circuit, what is the voltage of the battery if the resistance of R1 is 150 ohms, the total resistance is 250 ohms and the current though R2 is 25 milliamps? EL-0036 A. 12 volts B. 24 volts C. 1.5 volts D. 6.25 volts
Description : In the illustrated circuit, what is the voltage measured across R1 if the battery is 24 volts, the resistance of R1 is 34 ohms, and the resistance of R2 is 126 ohms? EL-0036 A. 24 volts B. 18.9 volts C. 5.1 volts D. 150 millivolts
Description : In the illustration, the diode between terminals 16 and 17 is to _________. EL-0046 A. act as a short circuit for the sensing coil when CEMF is applied B. insure that the voltage across the coil does not exceed 9 volts C. improve response time D. act as a filter to prevent hunting
Description : In the illustrated circuit the voltage is 12 VDC and the resistance is 3 ohms. If the battery is rated for 120 amp-hours, how long before the voltage will drop to 1.75 volts per cell? EL-0018 A. 12 hours B. 1.75 days C. 30 hours D. 2.5 days
Description : What would be the voltage drop across the series resistor of the circuit shown in the illustration if the source is 30 volts, the resistance of R1 is 10 ohms, R2 is 10 ohms and R3 is 10 ohms? EL-0032 A. 5 volts B. 10 volts C. 20 volts D. 30 volts
Description : What is the voltage across 'R3' of the illustrated circuit if the supply is 24 volts and the resistance of R1 is 3 ohms, R2 is 4 ohms, and R3 is 5 ohms? EL-0020 A. 2 volts B. 6 volts C. 8 volts D. 10 volts
Description : What would be the voltage drop across the parallel branches of the circuit shown in the illustration if the source is 30 volts the resistance for R1 is 10 ohms, R2 is 10 ohms and R3 is 10 ohms? EL-0032 A. 5 volts B. 10 volts C. 20 volts D. 30 volts
Description : What is the voltage across 'R2' of the illustrated circuit if the supply is 24 volts and the resistance of R1 is 3 ohms, R2 is 4 ohms, and R3 is 5 ohms? EL-0020 A. 2 volts B. 6 volts C. 8 volts D. 10 volts
Description : What is the voltage across 'R1' of the illustrated circuit if the supply is 24 volts and resistance of R1 is 3 ohms, R2 is 4 ohms, and R3 is 5 ohms? EL-0020 A. 2 volts B. 6 volts C. 8 volts D. 10 volts
Description : Considering the function of the circuit shown in the illustration, what is the purpose of supplying the thrust lever potentiometers with both (+) and (-) 15 volts? EL-0095 A. To select which ... alternate voltage supply if the other fails. D. So as to automatically select the position of Relay #
Description : If the line voltage to the controller shown in the illustration is 440 volts, what is applied across the control circuit? EL-0080 A. 110 volts B. 220 volts C. 440 volts D. 660 volts
Description : The open-circuit voltage of a fully charged lead-acid battery cell is _____________. A. 1.5 volts B. 1.8 volts C. 2.0 volts D. 2.3 volts
Description : In the illustration circuit, A, B, C, and D are each 12 volts. What is the voltage of the lead connected to C and D with respect to the lead connected to A and B? EL-0039 A. (+) 48 volts B. (-) 24 volts C. (-) 48 volts D. (+) 24 volts
Description : In the illustration circuit, A, B, C, and D are each 12 volts. What is the voltage at the output lead connected to 'A' and 'B' with respect to the output lead connected to 'C' and 'D'? EL-0039 A. (+) 48 volts B. (-) 24 volts C. (-) 48 volts D. (+) 24 volts
Description : Which of the following precautions should be taken when troubleshooting various power circuits using a common solenoid-type mechanical voltage tester (wiggins)? A. Never use this tester on circuits greater ... voltage expected in the circuit in order to prevent damage from an off-scale reading.