What would be the output of a negative clamper with a bias potential of −5 volts and an input voltage swing from +50 to −50 volts?

What would be the output of a negative clamper with a bias  potential of −5 volts and an input voltage swing from +50 to −50  volts?
by

1 Answer

Answer :

-5 volts.
by

Related questions

What type damper (with bias) clamps the most negative extremity of the output waveform to a negative potential?

Description : What type damper (with bias) clamps the most negative extremity of the output waveform to a negative potential?

Last Answer : Positive clamper with negative bias.

What type of bias (positive or negative) is added to a negative damper for the most positive extremity of the wave shape to be clamped above 0 volts?

Description : What type of bias (positive or negative) is added to a negative damper for the most positive extremity of the wave shape to be clamped above 0 volts?

Last Answer : Positive bias.

If the output of a half-wave rectifier is 50-volts peak, what is the average voltage

Description : If the output of a half-wave rectifier is 50-volts peak, what is the average voltage

Last Answer : 15.9 volts.

How does dc bias added to the input signal correct the distortion in the output signal?

Description : How does dc bias added to the input signal correct the distortion in the output signal?

Last Answer : The dc bias moves the input signal away from the step in the magnetism curve. This prevents the input signal from crossing the zero-point of the magnetism curve.

A negative damper with negative bias clamps the most positive extremity of the output wave shape to what polarity (positive or negative)?

Description : A negative damper with negative bias clamps the most positive extremity of the output wave shape to what polarity (positive or negative)?

Last Answer : Negative potential.

A, when there is an increase in the input voltage, the forward bias of Q1 increases/decreases (which one).

Description : A, when there is an increase in the input voltage, the forward bias of Q1 increases/decreases (which one).

Last Answer : Increases.

What are three advantages of adding an ac bias voltage to the input signal instead of adding a fixed dc bias voltage?

Description : What are three advantages of adding an ac bias voltage to the input signal instead of adding a fixed dc bias voltage?

Last Answer : a. Reproduces a stronger output signal. b. Greatly improves the SNR. c. Greatly reduces the natural tape hiss.

Why does adding dc vice ac bias voltage to the input signal result in a poor signal-to-noise ratio (SNR)?

Description : Why does adding dc vice ac bias voltage to the input signal result in a poor signal-to-noise ratio (SNR)?

Last Answer : With dc bias, the SNR is poor because only a small portion of the magnetism curve is straight enough to use, thus the output signal is weak compared with the natural tape hiss.

Why does using ac vice dc bias voltage result in a stronger output signal?

Description : Why does using ac vice dc bias voltage result in a stronger output signal?

Last Answer : Because an ac bias voltage of the proper frequency and level places the input signal away from both steps in the magnetism curve. The result is two undistorted output signals that are combined into one strong output.

Which breakdown theory explains the action that takes place in a heavily doped PN-junction with a reverse bias of less than 5 volts?

Description : Which breakdown theory explains the action that takes place in a heavily doped PN-junction with a reverse bias of less than 5 volts?

Last Answer : Zener effect.

A negative damper damps which extremity of the output waveshape to 0 volts?

Description : A negative damper damps which extremity of the output waveshape to 0 volts?

Last Answer : Most positive.

In the illustrated circuit, what is the phase relationship of the amplifier output compared to the input? EL-0022 A. 0° in-phase B. 180° out of phase C. phase angle of the input divided by power factor D. unable to determine without the value of the bias voltage

Description : In the illustrated circuit, what is the phase relationship of the amplifier output compared to the input? EL-0022 A. 0° in-phase B. 180° out of phase C. phase angle of the input divided by power factor D. unable to determine without the value of the bias voltage

Last Answer : Answer: B

Define: i) Input Offset Voltage ii) Input offset Current iii) Input Bias Current iv) Output offset voltage

Description : Define: i) Input Offset Voltage ii) Input offset Current iii) Input Bias Current iv) Output offset voltage

Last Answer : Definition of parameters of OPAMP is follows:  i) Input Offset Voltage: Input offset voltage is defined as the voltage that must be applied between the two input terminals of an OPAMP to null or ... to ground) and output voltage is obtained non zero such voltage is output offset voltage of opamp.

What is the average voltage (Eavg) Output of a full-wave rectifier with an output of 100 volts peak?

Description : What is the average voltage (Eavg) Output of a full-wave rectifier with an output of 100 volts peak?

Last Answer : 63.7 volts.

What is the average voltage (Eavg) output of a full-wave rectifier that has an output of 100 volts peak?

Description : What is the average voltage (Eavg) output of a full-wave rectifier that has an output of 100 volts peak?

Last Answer : 63.6 volts.

A common-emitter circuit has an input voltage of 0.1 volt, an output voltage of 2.0 volts, an input current of 0.5 milliamps, and an output current of 10 milliamps. What is the power gain? A. 20 B. 40 C. 400 D. 4000

Description : A common-emitter circuit has an input voltage of 0.1 volt, an output voltage of 2.0 volts, an input current of 0.5 milliamps, and an output current of 10 milliamps. What is the power gain? A. 20 B. 40 C. 400 D. 4000

Last Answer : Answer: C

When troubleshooting an amplifier, you measure an output of 30 volts. If the gain of the amplifier is 2, what must the input voltage be for the amplifier to work properly? A. 32 volts B. 30 volts C. 28 volts D. 15 volts

Description : When troubleshooting an amplifier, you measure an output of 30 volts. If the gain of the amplifier is 2, what must the input voltage be for the amplifier to work properly? A. 32 volts B. 30 volts C. 28 volts D. 15 volts

Last Answer : Answer: D

In the illustration, the component VR2 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to terminal 1 that controls the input to terminal 10 C. a zener diode that regulates the voltage to terminal 2 at 9.1 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Description : In the illustration, the component VR2 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to terminal ... 2 at 9.1 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Last Answer : Answer: C

In the illustration, the component VR1 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to terminal 9 that controls the input to terminal 10 C. a zener diode that regulates the voltage to terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Description : In the illustration, the component VR1 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to ... terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Last Answer : Answer: A

In the illustration, the component VR1 on the A1A1 PCB is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply B. a variable resistor diode to control the output to terminal 9 that controls the input to terminal 10 C. a zener diode that regulates the voltage to terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Description : In the illustration, the component VR1 on the A1A1 PCB is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply B. a variable resistor diode to control the output to terminal 9 that controls ... terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Last Answer : Answer: C

A tube has a transconductance of 800 mhos and a load resistor of 50 kohms. When control grid voltage varies by 6 volts, the plate voltage will vary by what amount?

Description : A tube has a transconductance of 800 mhos and a load resistor of 50 kohms. When control grid voltage varies by 6 volts, the plate voltage will vary by what amount?

Last Answer : 240 volts.

If the source voltage for the voltage divider in question 50 supplies 150 volts, what is the total current through the voltage divider?

Description : If the source voltage for the voltage divider in question 50 supplies 150 volts, what is the total current through the voltage divider?

Last Answer : 495 mA.

A circuit has a source voltage of 100 volts and two 50-ohm resistors connected in series. If the reference point for this circuit is placed between the two resistors, what would be the voltage at the reference point?

Description : A circuit has a source voltage of 100 volts and two 50-ohm resistors connected in series. If the reference point for this circuit is placed between the two resistors, what would be the voltage at the reference point?

Last Answer : 50 volts.

What is used to bias a magnetic amplifier so that the control winding remains free to accept control (input) signals?

Description : What is used to bias a magnetic amplifier so that the control winding remains free to accept control (input) signals?

Last Answer : A bias winding and associated circuitry.

Which portion of a sine-wave input is retained in the output of a series-negative limiter?

Description : Which portion of a sine-wave input is retained in the output of a series-negative limiter?

Last Answer : Positive.

Describe working of negative clamper circuit with neat diagram and waveform.

Description : Describe working of negative clamper circuit with neat diagram and waveform.

Last Answer : Working: In the first positive half cycle the capacitor will charge through the forward biased diode to peak voltage Vm as shown in circuit. Charging takes place very quickly as the ... reverse biased and stop conducting. Negative clamper adds a negative DC shift as shown in waveform.

Draw negative clamper circuit and explain its working.

Description : Draw negative clamper circuit and explain its working. 

Last Answer : Diagram: Working: During the positive half cycle of the input AC signal, the diode is forward biased and hence no signal appears at the output. In forward biased condition, the diode allows ... - 2Vm} which have the same polarity with each other. As a result, the signal shifted downwards. 

When a series voltage regulator is used to control output voltages, any increase in the input voltage results in an increase/a decrease (which one) in the resistance of the regulating device.

Description : When a series voltage regulator is used to control output voltages, any increase in the input voltage results in an increase/a decrease (which one) in the resistance of the regulating device.

Last Answer : An increase.

What characteristic is determined by the time required for a voltage wave to travel from the input end of an artificial transmission line to the output end and back again?

Description : What characteristic is determined by the time required for a voltage wave to travel from the input end of an artificial transmission line to the output end and back again?

Last Answer : Pulse width

What characteristic is determined by the time required for a voltage wave to travel from the input end of an artificial transmission line to the output end and back again?

Description : What characteristic is determined by the time required for a voltage wave to travel from the input end of an artificial transmission line to the output end and back again?

Last Answer : Pulse width.

If the inductance of a choke-input filter is increased, will the output ripple voltage amplitude (Er) increase or decrease?

Description : If the inductance of a choke-input filter is increased, will the output ripple voltage amplitude (Er) increase or decrease?

Last Answer : Decrease.

When a series voltage regulator is used to control output voltages, any increase in the input voltage results in an increase/a decrease in the resistance of the regulating device.

Description : When a series voltage regulator is used to control output voltages, any increase in the input voltage results in an increase/a decrease in the resistance of the regulating device.

Last Answer : Increase.

The device in figure 'B' shown in the illustration can be used to control an AC load yet maintain its high gain by ______________. EL-0091 A. connecting the load to the output side of the bridge B. reversing the current flow through the control winding C. connecting the load to the input side of the bridge D. reversing the current flow through the bias winding

Description : The device in figure 'B' shown in the illustration can be used to control an AC load yet maintain its high gain by ______________. EL-0091 A. connecting the load to the output side of the ... connecting the load to the input side of the bridge D. reversing the current flow through the bias winding

Last Answer : Answer: C

In a circuit such as that shown in figure 3-16, if R1 has a value of 50 ohms and R2 has a value of 250 ohms and the input signal has a value of +10 millivolts, what is the value of the output signal?

Description : In a circuit such as that shown in figure 3-16, if R1 has a value of 50 ohms and R2 has a value of 250 ohms and the input signal has a value of +10 millivolts, what is the value of the output signal?

Last Answer : 60 millivolts.

Define supply voltage Rejection Ratio and Output voltage Swing.

Last Answer : Supply Voltage Rejection Ratio: It is defined as the ratio of change of input offset voltage to the change in one supply voltage while keeping other supply voltage constant. Ideally, SVRR=0 Output ... that an OPAMP can produce. Since the quiescent output is ideally zero, the ac output voltage

To properly bias an NPN transistor, what polarity voltage is applied to the collector, and what is its relationship to the base voltage?

Description : To properly bias an NPN transistor, what polarity voltage is applied to the collector, and what is its relationship to the base voltage?

Last Answer : Positive, more positive.

If a voltage (positive or negative) is measured on the "1" output of a flip-flop, what state is it in?

Description : If a voltage (positive or negative) is measured on the "1" output of a flip-flop, what state is it in?

Last Answer : SET state.

What is the effect upon an electron that enters the buncher gap when the potential across the grids is at 0 volts?

Description : What is the effect upon an electron that enters the buncher gap when the potential across the grids is at 0 volts?

Last Answer : There is no effect

If the electricity represented by the wave form in 'B' were applied to the left side of the illustrated circuit, the output on the right side would be ____________. EL-0064 A. direct current with the top lead positive with repect to the lower lead B. direct current, half wave rectified with a ripple frequency of 60 hz C. direct current with the top lead negative with repect to the lower lead D. clipped to a value equal to the square root of 3 times the input voltage value

Description : If the electricity represented by the wave form in 'B' were applied to the left side of the illustrated circuit, the output on the right side would be ____________. EL-0064 A. direct current with the ... lower lead D. clipped to a value equal to the square root of 3 times the input voltage value

Last Answer : Answer: C

what is the difference between (−5)² and −5²?

Description : what is the difference between (−5)² and −5²?

Last Answer : Haiku: 5/7/5 tanka: 5/7/5/7/7

A positive damper clamps which extremity of the output signal to 0 volts?

Description : A positive damper clamps which extremity of the output signal to 0 volts?

Last Answer : Most negative.

An operational amplifier, as used in today's consoles, has a calculated gain of 5. This means that when the input changes _____________. A. 5 volts, the output changes 10 volts B. 10 volts, the output changes 5 volts C. 2 volts, the output changes 10 volts D. 10 volts, the output changes 2 volts

Description : An operational amplifier, as used in today's consoles, has a calculated gain of 5. This means that when the input changes _____________. A. 5 volts, the output changes 10 volts B. 10 volts, the output changes 5 volts C. 2 volts, the output changes 10 volts D. 10 volts, the output changes 2 volts

Last Answer : Answer: C

One method of troubleshooting digital circuits in a console is to ___________. A. supply alternate logic levels at the input(s) and test for change of state conditions at the output B. ground all inputs and test for a logic '1' at the output C. open all inputs and test for a logic '0' at the output D. vary each input smoothly from 0-10 volts and test for similar variance at the output

Description : One method of troubleshooting digital circuits in a console is to ___________. A. supply alternate logic levels at the input(s) and test for change of state conditions at the output B. ground all ... output D. vary each input smoothly from 0-10 volts and test for similar variance at the output

Last Answer : Answer: A

An operational amplifier, as used in today's consoles, may have a calculated gain of 5. This means that as the input changes by ______________. A. 1 volt, the output changes 5 volts B. 5 volts, the output changes 1 volt C. 5 volts, the output changes 10 volts D. 10 volts, the output changes 5 volts

Description : An operational amplifier, as used in today's consoles, may have a calculated gain of 5. This means that as the input changes by ______________. A. 1 volt, the output changes 5 volts B. 5 volts, the output changes 1 volt C. 5 volts, the output changes 10 volts D. 10 volts, the output changes 5 volts

Last Answer : Answer: A

If the mu of a tube is 85 and the signal at the control grid is 4 volts ac, the plate voltage will vary by what amount?

Description : If the mu of a tube is 85 and the signal at the control grid is 4 volts ac, the plate voltage will vary by what amount?

Last Answer : 340 volts.

The plate voltage of a tube will vary 126 volts when a 3-volt ac signal is applied to the control grid. What is the gain of this tube?

Description : The plate voltage of a tube will vary 126 volts when a 3-volt ac signal is applied to the control grid. What is the gain of this tube?

Last Answer : 42.

Using the graph in figure 3-7, what is the approximate value of current when the voltage is 12.5 volts?

Description : Using the graph in figure 3-7, what is the approximate value of current when the voltage is 12.5 volts?

Last Answer : 1.25 amperes.

a. Define the term "working voltage" of a capacitor. b. What should be the working voltage of a capacitor in a circuit that is operating at 600 volts?

Description : a. Define the term "working voltage" of a capacitor. b. What should be the working voltage of a capacitor in a circuit that is operating at 600 volts?

Last Answer : a. It is the maximum voltage the capacitor can work without risk of damage. b. 900 volts.

In a three-wire, 230/115 volt DC system, the potential between neutral and negative is _____________. A. 0 volts B. 115 volts C. 230 volts D. 460 volts

Description : In a three-wire, 230/115 volt DC system, the potential between neutral and negative is _____________. A. 0 volts B. 115 volts C. 230 volts D. 460 volts

Last Answer : Answer: B