Description : If the load requirement consists of both positive and negative voltages, what technique is used in the voltage divider to supply the loads from a single voltage source?
Last Answer : The ground (reference point) is placed in the proper point in the voltage divider so that positive and negative voltages are supplied
Description : If a voltage divider is required for a load that will use 450 mA of current, what should be the value of bleeder current?
Last Answer : 45 mA rule-of-thumb.
Description : A circuit has a source voltage of 100 volts and two 50-ohm resistors connected in series. If the reference point for this circuit is placed between the two resistors, what would be the voltage at the reference point?
Last Answer : 50 volts.
Description : In the illustrated circuit, what is the voltage of the battery if the resistance of R1 is 150 ohms, the total resistance is 250 ohms and the current though R2 is 25 milliamps? EL-0036 A. 12 volts B. 24 volts C. 1.5 volts D. 6.25 volts
Last Answer : Answer: D
Description : What information must be known to determine the component values for a voltage divider?
Last Answer : The source voltage and load requirements (voltage and current).
Description : What would be the output of a negative clamper with a bias potential of −5 volts and an input voltage swing from +50 to −50 volts?
Last Answer : -5 volts.
Description : If the output of a half-wave rectifier is 50-volts peak, what is the average voltage
Last Answer : 15.9 volts.
Description : A tube has a transconductance of 800 mhos and a load resistor of 50 kohms. When control grid voltage varies by 6 volts, the plate voltage will vary by what amount?
Last Answer : 240 volts.
Description : If the total source voltage of the three-wire distribution system shown in the illustration is 240 volts, what is the voltage across load L5? [ NOTE: Kirchhoff's voltage and current laws apply ] EL-0075 A. 110.4 volts B. 112.2 volts C. 113.0 volts D. 114.8 volts
Description : If the total source voltage of the three-wire distribution system shown in the illustration is 240 volts, what is the voltage across load L1? [NOTE: Kirchhoff's voltage and current laws apply.] EL-0075 A. 110.4 volts B. 112.2 volts C. 113.3 volts D. 114.8 volts
Description : If the total source voltage of the three-wire distribution system shown in the illustration is 240 volts, what is the voltage across load L2? [NOTE: Kirchhoff's voltage and current laws apply.] EL-0075 A. 110.4 volts B. 112.2 volts C. 113.0 volts D. 114.8 volts
Last Answer : Answer: C
Description : If the total source voltage of the three-wire distribution system shown in the illustration is 240 volts, what is the voltage across load L3? [NOTE: Kirchhoff's voltage and current laws apply.] EL-0075 A. 110.4 volts B. 112.2 volts C. 113.0 volts D. 114.8 volts
Last Answer : Answer: B
Description : Using the graph in figure 3-7, what is the approximate value of current when the voltage is 12.5 volts?
Last Answer : 1.25 amperes.
Description : A series circuit consists of two resistors in series. R1 = 25 ohms and R2 = 30 ohms. The circuit current is 6 amps. What is the (a) source voltage, (b) voltage dropped by each resistor, (c) total power, and (d) power used by each resistor?
Last Answer : (a) 330 volts. (b) E1 = 150 volts. E2 = 180 volts. (c) 1.98 kilowatts. (d) P1 = 900 watts. P2 = 1.08 kilowatts component but in a parallel circuit total current divides among the available paths.
Description : A series circuit consisting of three resistors has a current of 3 amps. If R1 = 20 ohms, R2= 60 ohms, and R 3 = 80 ohms, what is the (a) total resistance and (b) source voltage of the circuit?
Last Answer : (a) 160 ohms. (b) 480 ohms
Description : If the total source voltage of the three-wire distribution system shown in the illustration is 240 volts, what is the voltage across load L4? EL-0075 A. 110.4 volts B. 112.2 volts C. 113.0 volts D. 114.8 volts
Last Answer : Answer: A
Description : In the illustrated circuit, what is the voltage measured across R1 if the battery is 24 volts, the resistance of R1 is 34 ohms, and the resistance of R2 is 126 ohms? EL-0036 A. 24 volts B. 18.9 volts C. 5.1 volts D. 150 millivolts
Description : A lamp has a source voltage of 110 volts and a current of 0.9 amps. What is the resistance of the lamp? A. 0.008 ohms B. 0.08 ohms C. 12.22 ohms D. 122.22 ohms
Description : A series R-L circuit is suddenly connected to d.c. voltage source of V volts. The current in this series circuit, just after the switch is closed, is equal to (1) Zero (2) V/L (3) V/C (4) V.L/C
Last Answer : When is a series RLC circuit is over damped
Description : An LED is operated on a 12 volt automobile circuit. The voltage drop across the LED is 2 volts and the current must be limited to 50 milliamps to prevent its overheating and destruction. What size resistor must be used? w) 60 ohms x) 100 ohms y) 120 ohms z) 200 ohms
Last Answer : ANSWER: Z -- 200 OHMS
Description : if voltage is 230 Volts , frequency is 50 Hz and current is 1 ampere then what will be the resistance?
Last Answer : As V = 230v and I = 1A Therfore by ohm's law V =IR R = V/I =230/1 =230 ohm
Description : What would the source voltage (ES) in figure 3-39 be if the current through R2 were 2 milliamps?
Last Answer : 60 volts.
Description : What is the average voltage (Eavg) Output of a full-wave rectifier with an output of 100 volts peak?
Last Answer : 63.7 volts.
Description : What is the average voltage (Eavg) output of a full-wave rectifier that has an output of 100 volts peak?
Last Answer : 63.6 volts.
Description : If the mu of a tube is 85 and the signal at the control grid is 4 volts ac, the plate voltage will vary by what amount?
Last Answer : 340 volts.
Description : The plate voltage of a tube will vary 126 volts when a 3-volt ac signal is applied to the control grid. What is the gain of this tube?
Last Answer : 42.
Description : a. Define the term "working voltage" of a capacitor. b. What should be the working voltage of a capacitor in a circuit that is operating at 600 volts?
Last Answer : a. It is the maximum voltage the capacitor can work without risk of damage. b. 900 volts.
Description : If the alternating source in Q41 is changed to 200 volts peak-to-peak, what is Iavg?
Last Answer : Iavg = 0.636 × Imax = 1.41 amperes.
Description : A 10 bit resistive divider is constructed such that the current through the LSB resistor is 100μA. The maximum current that will flow through the MSB resistor is
Last Answer : A 10 bit resistive divider is constructed such that the current through the LSB resistor is 100μA. The maximum current that will flow through the MSB resistor is 51.2mA.
Description : A battery is connected to a circuit containing three resistors in parallel. The values of the three resistors are 2 ohms, 3 ohms, and 6 ohms. What is the voltage of the battery if the total circuit current is 12 amps? A. 2 volts B. 6 volts C. 12 volts D. 24 volt
Description : The distance between a generator and its load is 100 feet. What would be the approximate total voltage drop across a two wire supply cable if the current were 5.5 amperes and the resistance of the wire were 2.525 ohms per 1,000 feet? A. 0.5 volts B. 1.38 volts C. 1.90 volts D. 2.77 volts
Description : What is the purpose of the 'annunciator module' (6000F35) shown in the illustration? EL-0094 A. Provide an input to the setpoint module. B. Drive the alarm lamp and, through the controller, the horn. ... and +24 volts to their respective power supplies. D. Connect 24 volts to both sides of the horn.
Description : What would be the total current flowing in the circuit shown in the illustration if the source is 30 volts, the resistance of R1 is 10 ohms, R2 is 10 ohms and R3 is 10 ohms? EL-0032 A. 1 amp B. 2 amps C. 5 amps D. 15 amps
Description : The maximum permissible chloride content in treated water of public water supplies should not exceed (A) 50 P.P.M. (B) 100 P.P.M. (C) 150 P.P.M. (D) 250 P.P.M.
Last Answer : (D) 250 P.P.M.
Description : What is a voltage divider in Arduino?
Last Answer : A voltage divider in Arduino is a circuit that divides a voltage into smaller values using two resistors.
Description : Explain with circuit diagram, voltage divider biasing method and state its two advantages.
Last Answer : a)Here R1 and R2 forms voltage divider biasing arrangement. b)voltage drop across R2 ,forward biases the base emitter junction. c)so base current flows and hence collector ... Operating point stabilized against shift in temperature. · Operating point is almost independent of β variation
Description : Voltage divider rule
Last Answer : Voltage divider rule
Description : Draw circuit diagram of voltage divider biasing list two advantages of voltage divider biasing of BJT.
Last Answer : Two advantages of voltage divider biasing of BJT. 1. It is very simple method of transistor biasing. 2. The biasing conditions can be very easily set. 3. there is no loading of ... 5. The resistor RE introduces a negative feedback. So all the advantages of negative feedback are obtained.
Description : The disadvantage of voltage divider bias is that 1. it has a high stability factor 2. it has many resistors 3. it allows thermal runaway 4. it does not allow faithful amplification
Last Answer : Is the power off this word only current
Last Answer : A voltage divider is always a series circuit.
Description : A device which supplies a voltage is commonly referred to by what name?
Last Answer : A voltage source.
Description : If Eeff is 130 volts and Ieff is 3 amperes, what is the total resistance (RT) in the circuit?
Last Answer : 43.3 ohms.
Description : If the load in question 50 requires a voltage of +90 V, what should be the value of the bleeder resistor?
Last Answer : 2 kΩ
Description : What would be the voltage drop across the series resistor of the circuit shown in the illustration if the source is 30 volts, the resistance of R1 is 10 ohms, R2 is 10 ohms and R3 is 10 ohms? EL-0032 A. 5 volts B. 10 volts C. 20 volts D. 30 volts
Description : What would be the voltage drop across the parallel branches of the circuit shown in the illustration if the source is 30 volts the resistance for R1 is 10 ohms, R2 is 10 ohms and R3 is 10 ohms? EL-0032 A. 5 volts B. 10 volts C. 20 volts D. 30 volts
Description : Moisture accumulating in electric motors and generator windings having a cold insulation resistance greater than 50,000 ohms may be baked out with internal heat. This heat can be developed by ____________. ... an electric welder and feeding it into the armature while running the motor at full speed
Description : Current divider rule
Last Answer : Current divider rule
Description : What is the approximate voltage produced by a nickel-cadmium battery cell? A. 1.25 volts B. 1.50 volts C. 2.20 volts D. 6.05 volts
Description : What will be the total output voltage if four 1.5 volt batteries are connected in a series-parallel arrangement as shown in the illustration? EL-0039 A. 1.5 volts B. 3.0 volts C. 4.5 volts D. 6.0 volts
Description : What would be the total power consumed in the circuit shown in the illustration if the source is 30 volts the resistance for R1 is 10 ohms, R2 is 10 ohms, and R3 is 10 ohms? EL-0032 A. 10 watts B. 40 watts C. 45 watts D. 60 watts