In Class ‘B’ amplifier, the output current flows for

In Class ‘B’ amplifier, the output current flows for
by

1 Answer

Answer :

In Class ‘B’ amplifier, the output current flows for half input cycle

by

Related questions

An amplifier without feedback has a voltage gain of 50, input resistance 1kΩ and output resistance of 2.5kΩ.

Description : An amplifier without feedback has a voltage gain of 50, input resistance 1kΩ and output resistance of 2.5kΩ. The input resistance of the current-shunt negative feedback amplifier using the above amplifier with a feedback factor of 0.2 would be: (1) 1/11 kΩ (2) 1/5 kΩ (3) 5 kΩ (4) 11 kΩ

Last Answer : An amplifier without feedback has a voltage gain of 50, input resistance 1kΩ and output resistance of 2.5kΩ. The input resistance of the current-shunt negative feedback amplifier using the above amplifier with a feedback factor of 0.2 would be: 1/11 kΩ

For Cascode amplifier the output impedance becomes

Description : For Cascode amplifier the output impedance becomes 

Last Answer : For Cascode amplifier the output impedance becomes very high

An operational amplifier has an open loop gain of 200,000. Its output exhibits saturation at 10V.

Description : An operational amplifier has an open loop gain of 200,000. Its output exhibits saturation at 10V. The threshold differential voltage of the amplifier is  A) 25 micro-volt B) 50 micro-volt C) 5 Volts D) 10 volts

Last Answer : An operational amplifier has an open loop gain of 200,000. Its output exhibits saturation at 10V. The threshold differential voltage of the amplifier is 50 micro-volt

The main function of the transformer used in the output of a power amplifier is

Description : The main function of the transformer used in the output of a power amplifier is  (A) To step up the voltage  (B) to increase the voltage gain  (C) to safeguard the transistor against overheating  (D) to match the load impedance with dynamic output resistance of the transistor

Last Answer : The main function of the transformer used in the output of a power amplifier is to match the load impedance with dynamic output resistance of the transistor

Class A amplifier is used when

Description : Class A amplifier is used when  (A) No phase inversion is required (B) Highest voltage gain is required (C) dc voltages are to be amplified (D) Minimum distortion is desired. 

Last Answer : Class A amplifier is used when Minimum distortion is desired. 

In class - A power amplifier, the collector dissipation is maximum when

Description : In class - A power amplifier, the collector dissipation is maximum when  (a) no signal is present  (b) signal swing is maximum  (c) signal swing is (1/1.414) of its maximum  (d) none of the above

Last Answer : In class - A power amplifier, the collector dissipation is maximum when no signal is present

The efficiency of a class B push-pull amplifier is

Description : The efficiency of a class B push-pull amplifier is

Last Answer : The efficiency of a class B push-pull amplifier is 75-80%

In class-A amplifier conduction extends over 360° because the operating point.

Description : In class-A amplifier conduction extends over 360° because the operating point.  1. Located near saturation point 2. Located at or near cut-off point 3. Located on load line 4. Located in the centre of load line 

Last Answer : In class-A amplifier conduction extends over 360° because the operating point.  1. Located near saturation point 2. Located at or near cut-off point 3. Located on load line 4. Located in the centre of load line 

The unity gain bandwidth of an inverting amplifier is 10 MHz What would be the bandwidth if the gain is

Description : The unity gain bandwidth of an inverting amplifier is 10 MHz What would be the bandwidth if the gain is increased to 10 V/V? A) 100 MHz B) 1 MHz C) 10 MHz D) 1 kHz 

Last Answer : The unity gain bandwidth of an inverting amplifier is 10 MHz What would be the bandwidth if the gain is increased to 10 V/V? A) 100 MHz B) 1 MHz C) 10 MHz D) 1 kHz 

The ideal operational amplifier does not have:

Description : The ideal operational amplifier does not have: (1) Infinite input resistance (2) Infinite output resistance (3) Infinite voltage gain (4) Infinite bandwidth 

Last Answer : The ideal operational amplifier does not have: Infinite output resistance

The gain of an FET amplifier can be changed by changing:

Description : The gain of an FET amplifier can be changed by changing: (1) rm (2) gm (3) Rd (4) None of these

Last Answer : The gain of an FET amplifier can be changed by changing: gm

If the feedback factor of an amplifier is 0.1 and its gain without feedback is 40, then its gain with feedback is

Description : If the feedback factor of an amplifier is 0.1 and its gain without feedback is 40, then its gain with feedback is (a) – 13.3 (b) 200 (c) 8 (d) 10 

Last Answer : If the Feedback Factor of an amplifier is 0.1 and its gain without feedback is 40, then feedback is 40,then its gain with feedback is 8.

A low noise amplifier has an effective noise temperature of 50 k. The absolute noise figure is

Description : A low noise amplifier has an effective noise temperature of 50 k. The absolute noise figure is

Last Answer : A low noise amplifier has an effective noise temperature of 50 k. The absolute noise figure is 1.172

An amplifier operating over the frequency range from 18 to 20 MHz has 10 kilo ohm input resistor. What is

Description : An amplifier operating over the frequency range from 18 to 20 MHz has 10 kilo ohm input resistor. What is the r.m.s. noise voltage at the input to this amplifier if the ambient temperature is 27o C

Last Answer : An amplifier operating over the frequency range from 18 to 20 MHz has 10 kilo ohm input resistor. What is the r.m.s. noise voltage at the input to this amplifier if the ambient temperature is 27o C 18.2 microvolt

For a feedback amplifier, if the loop gain is much greater than unity, the closed loop gain will be equal to

Description : For a feedback amplifier, if the loop gain is much greater than unity, the closed loop gain will be equal to

Last Answer : For a feedback amplifier, if the loop gain is much greater than unity, the closed loop gain will be equal to inverse of feedback factor

An amplifier without feedback has a gain of 1000. The gain with a negative feedback of 0.009 is

Description : An amplifier without feedback has a gain of 1000. The gain with a negative feedback of 0.009 is  A) 10 B) 100 C) 125 D) 900

Last Answer : 100

In a radio receiver the IF amplifier

Description : In a radio receiver the IF amplifier  (A) is tuned above the stations incoming frequency (B) amplifies the output of local oscillator (C) is fixed tuned to one particular frequency (D) can be tuned to various isolate frequencies

Last Answer : In a radio receiver the IF amplifier is fixed tuned to one particular frequency

Negative feedback amplifier has a signal corrupted by noise as its input. The amplifier will

Description : Negative feedback amplifier has a signal corrupted by noise as its input. The amplifier will   (A) Amplify the noise as much as the signal (B) Reduce the noise (C) Increase the noise (D) Not effect the noise

Last Answer : Negative feedback amplifier has a signal corrupted by noise as its input. The amplifier will Reduce the noise

In an IF amplifier, the IF transformer is provided with tapping to

Description : In an IF amplifier, the IF transformer is provided with tapping to  (a) increase the voltage gain (b) increase the bandwidth of the resonance circuit (c) increase the impedance ... resonance circuit to the following cascaded amplifier (d) increase the quality factor of the resonance circuit 

Last Answer : In an IF amplifier, the IF transformer is provided with tapping to increase the voltage gain

In a Klystron amplifier, the RF voltage produces

Description : In a Klystron amplifier, the RF voltage produces  (a) amplitude modulation (b) frequency modulation (c) phase modulation (d) velocity modulation

Last Answer : In a Klystron amplifier, the RF voltage produces velocity modulation

Which of the following amplifier has the least distortion.

Description : Which of the following amplifier has the least distortion. • Class E • Class D • Class C • Class A

Last Answer : Which of the following amplifier has the least distortion. • Class E • Class D • Class C • Class A

The battery operated pre-amplifier with a consumption of 10 Watts can work on battery of 12

Description : The battery operated pre-amplifier with a consumption of 10 Watts can work on battery of 12 volt, 100 AH having efficiency of 50% for • 120 hrs. • 60 hrs. • 100 hrs. • 10 hrs.

Last Answer : The battery operated pre-amplifier with a consumption of 10 Watts can work on battery of 12 volt, 100 AH having efficiency of 50% for 60 hrs.

The voltage gain of a common base amplifier depends on

Description : The voltage gain of a common base amplifier depends on  1. Load resistor RL 2. input resistance of transistor 3. Ac alpha 4. All the above 

Last Answer : The voltage gain of a common base amplifier depends on  1. Load resistor RL 2. input resistance of transistor 3. Ac alpha 4. All the above 

Just as a voltage amplifier signal voltage a power amplifier.

Description : Just as a voltage amplifier signal voltage a power amplifier.  1.amplifier power  2.amplifier signal  3.converts the signal ac power into DC power  4.converts a dc power into useful AC power 

Last Answer : Just as a voltage amplifier signal voltage a power amplifier.  1.amplifier power  2.amplifier signal  3.converts the signal ac power into DC power  4.converts a dc power into useful AC power 

Harmonic distortion of the signal is produced in an RC coupled transistor amplifier. The probable

Description : Harmonic distortion of the signal is produced in an RC coupled transistor amplifier. The probable component responsible for this distortion is  (A) The transistor itself  (B) the power supply Vcc  (C) the coupling capacitor Cc  (D) the biasing resistors

Last Answer : Harmonic distortion of the signal is produced in an RC coupled transistor amplifier. The probable component responsible for this distortion is The transistor itself 

The main component responsible for the fall of gain of an RC coupled amplifier in low frequency

Description : The main component responsible for the fall of gain of an RC coupled amplifier in low frequency range is  (A) The active device itself (tube, or transistor)  (B) stray shunt capacitance Cs  (C) the grid leak resistance Rg  (D) coupling capacitor Cc

Last Answer : The main component responsible for the fall of gain of an RC coupled amplifier in low frequency range is coupling capacitor Cc

Negative feedback in an amplifier is accompanied by

Description : Negative feedback in an amplifier is accompanied by (A) Gain less sensitive to component variations (B) Increase in gain (C) Decrease in bandwidth (D) None of the above

Last Answer : Negative feedback in an amplifier is accompanied by Gain less sensitive to component variations 

What is the importance of negative feedback in the operational amplifier?

Description : What is the importance of negative feedback in the operational amplifier? (A) It maintains the gain (B) The voltage difference between the input terminals is maintained at a very small value ( ... value (D) The voltage difference between the input terminals is maintained at a very high value

Last Answer : The voltage difference between the input terminals is maintained at a very small value

The closed-loop voltage gain of an inverting amplifier equal to

Last Answer : The closed-loop voltage gain of an inverting amplifier equal to The feedback resistance divided by the input resistance.

When the initial slope of input sine wave is greater than the slew rate of an OPAMP, the output:

Description : When the initial slope of input sine wave is greater than the slew rate of an OPAMP, the output: (1) Has no offset (2) Approaches to triangular waveshape (3) Is pure sinusoidal (4) Is square wave 

Last Answer : When the initial slope of input sine wave is greater than the slew rate of an OPAMP, the output: Approaches to triangular waveshape

The transistor configuration to connect 4 W speaker with 600 W output impedance audio

Description : The transistor configuration to connect 4 W speaker with 600 W output impedance audio amplifier is • Common Emitter • Common Base • Common Collector • None of the above.

Last Answer : The transistor configuration to connect 4 W speaker with 600 W output impedance audio amplifier is Common Collector

The voltage at the reference electrode of the circuit shown in the illustration is applied to the input of a/an ______________. EL-0090 A. class A detector whose output drives an autotransformer B. operational amplifier whose output controls a step-up voltage reactor C. amplitude modulator whose output drives an 2-stage isolation transformer D. magnetic amplifier whose output controls a saturable reactor

Description : The voltage at the reference electrode of the circuit shown in the illustration is applied to the input of a/an ______________. EL-0090 A. class A detector whose output drives an ... drives an 2-stage isolation transformer D. magnetic amplifier whose output controls a saturable reactor

Last Answer : Answer: D

Draw the single stage class A power amplifier circuit diagram and draw the input and output waveforms.

Description : Draw the single stage class A power amplifier circuit diagram and draw the input and output waveforms.

Last Answer : Circuit diagram:- Input / Output waveforms:-

Cross over distortion in class - B push-p amplifiers:

Description : Cross over distortion in class - B push-p amplifiers:  1. Is due to transistor operating near saturation region  2. Can be eliminated by operating them in class operation  3. Occurs because two power transistors do not exactly matching parameters  4. Always occurs in low signal area

Last Answer : Cross over distortion in class - B push-p amplifiers:  1. Is due to transistor operating near saturation region  2. Can be eliminated by operating them in class operation  3. Occurs because two power transistors do not exactly matching parameters  4. Always occurs in low signal area

Frequency counters or frequency divihat establishes the value of the current that flows in the output of figure 4-43?

Description : hat establishes the value of the current that flows in the output of figure 4-43?

Last Answer : The frequency of the voltage input.

To provide its unique characteristics to analog circuits, the operational amplifier is made up of a/an ______________. A. voltage amp, current amp and output amp B. input amp, power amp and output amp C. scaling amp, power amp and voltage amp D. differential amp, voltage amp and output amp

Description : To provide its unique characteristics to analog circuits, the operational amplifier is made up of a/an ______________. A. voltage amp, current amp and output amp B. input amp, power amp and output amp C. scaling amp, power amp and voltage amp D. differential amp, voltage amp and output amp

Last Answer : Answer: D

Amplifier produces output with more A. power only B. voltage only C. current only D. power and voltage

Description : Amplifier produces output with more A. power only B. voltage only C. current only D. power and voltage

Last Answer : power and voltage

If current gain is required from an rf amplifier, what type of component should be used as an output coupling element?

Description : If current gain is required from an rf amplifier, what type of component should be used as an output coupling element?

Last Answer : A step-down transformer.

An amplifier is said to suffer from distortion when its output is - (1) low (2) different from input (3) noisy (4) larger than its input

Description : An amplifier is said to suffer from distortion when its output is - (1) low (2) different from input (3) noisy (4) larger than its input

Last Answer : (3) noisy Explanation: Amplifier Distortion can take on many forms such as Amplitude, Frequency and Phase Distortion due to Clipping. For a signal amplifier to operate correctly without any distortion to the output signal, it requires some form of DC Bias on its Base or Gate terminal.

An operational amplifier, as used in today's consoles, has a calculated gain of 5. This means that when the input changes _____________. A. 5 volts, the output changes 10 volts B. 10 volts, the output changes 5 volts C. 2 volts, the output changes 10 volts D. 10 volts, the output changes 2 volts

Description : An operational amplifier, as used in today's consoles, has a calculated gain of 5. This means that when the input changes _____________. A. 5 volts, the output changes 10 volts B. 10 volts, the output changes 5 volts C. 2 volts, the output changes 10 volts D. 10 volts, the output changes 2 volts

Last Answer : Answer: C

When troubleshooting an amplifier, you measure an output of 30 volts. If the gain of the amplifier is 2, what must the input voltage be for the amplifier to work properly? A. 32 volts B. 30 volts C. 28 volts D. 15 volts

Description : When troubleshooting an amplifier, you measure an output of 30 volts. If the gain of the amplifier is 2, what must the input voltage be for the amplifier to work properly? A. 32 volts B. 30 volts C. 28 volts D. 15 volts

Last Answer : Answer: D

In the illustration, the component VR2 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to terminal 1 that controls the input to terminal 10 C. a zener diode that regulates the voltage to terminal 2 at 9.1 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Description : In the illustration, the component VR2 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to terminal ... 2 at 9.1 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Last Answer : Answer: C

In the illustration, the component VR1 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to terminal 9 that controls the input to terminal 10 C. a zener diode that regulates the voltage to terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Description : In the illustration, the component VR1 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to ... terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Last Answer : Answer: A

In the illustrated circuit, what is the phase relationship of the amplifier output compared to the input? EL-0022 A. 0° in-phase B. 180° out of phase C. phase angle of the input divided by power factor D. unable to determine without the value of the bias voltage

Description : In the illustrated circuit, what is the phase relationship of the amplifier output compared to the input? EL-0022 A. 0° in-phase B. 180° out of phase C. phase angle of the input divided by power factor D. unable to determine without the value of the bias voltage

Last Answer : Answer: B

An operational amplifier, as used in today's consoles, may have a calculated gain of 5. This means that as the input changes by ______________. A. 1 volt, the output changes 5 volts B. 5 volts, the output changes 1 volt C. 5 volts, the output changes 10 volts D. 10 volts, the output changes 5 volts

Description : An operational amplifier, as used in today's consoles, may have a calculated gain of 5. This means that as the input changes by ______________. A. 1 volt, the output changes 5 volts B. 5 volts, the output changes 1 volt C. 5 volts, the output changes 10 volts D. 10 volts, the output changes 5 volts

Last Answer : Answer: A

As shown in the illustration, the circuit which 'shapes' the linear output of the thrust lever so that the steady-state ship speed is linear with respect to that lever's setting is the _____________. EL-0095 A. 'pitch controller' B. 'error amplifier' C. 'function generator' D. 'servo amplifier'

Description : As shown in the illustration, the circuit which 'shapes' the linear output of the thrust lever so that the steady-state ship speed is linear with respect to that lever's setting is the _____________. EL-0095 A. 'pitch controller' B. 'error amplifier' C. 'function generator' D. 'servo amplifier'

Last Answer : Answer: C

Basic operating characteristics of the operational amplifier such as gain and stability are the function of its _____________. A. differential input stage B. power output stage C. feedback circuit D. supply voltages

Description : Basic operating characteristics of the operational amplifier such as gain and stability are the function of its _____________. A. differential input stage B. power output stage C. feedback circuit D. supply voltages

Last Answer : Answer: C

One feature of the operational amplifier is that it can have ____________. A. up to ten outputs B. binary coded decimal inputs C. several hundred amps at the output D. inverting and non-inverting inputs

Description : One feature of the operational amplifier is that it can have ____________. A. up to ten outputs B. binary coded decimal inputs C. several hundred amps at the output D. inverting and non-inverting inputs

Last Answer : Answer: D

Not a reason for the use of an antenna coupler. A. To make the antenna look resistive B. To provide the output amplifier with the correct load impedance C. To discriminate against harmonics D. To prevent re-radiation of the local oscillator

Description : Not a reason for the use of an antenna coupler. A. To make the antenna look resistive B. To provide the output amplifier with the correct load impedance C. To discriminate against harmonics D. To prevent re-radiation of the local oscillator

Last Answer : D. To prevent re-radiation of the local oscillator