The transistor configuration to connect 4 W speaker with 600 W output impedance audio

The transistor configuration to connect 4 W speaker with 600 W output impedance audio amplifier is

• Common Emitter

• Common Base

• Common Collector

• None of the above.
by

1 Answer

Answer :

The transistor configuration to connect 4 W speaker with 600 W output impedance audio amplifier is Common Collector

by

Related questions

For Cascode amplifier the output impedance becomes

Description : For Cascode amplifier the output impedance becomes 

Last Answer : For Cascode amplifier the output impedance becomes very high

Identify type of BJT configuration having following features : (i) BJT configuration having the least current gain. (ii) KIT configuration called as voltage follower. (iii) BJT configuration having current gain less than one. (iv) BJT configuration suitable for impedance matching. (v) BIT configuration suitable for voltage amplification. (vi) BJT configuration having the least output impedance.

Description : Identify type of BJT configuration having following features : (i) BJT configuration having the least current gain. (ii) KIT configuration called as voltage follower. (iii) BJT ... configuration suitable for voltage amplification. (vi) BJT configuration having the least output impedance.  

Last Answer : (i) BJT configuration having the least current gain : Common Base Configuration  (ii) KIT configuration called as voltage follower: Common Collector Configuration  (iii) BJT ... Emitter Configuration  (vi) BJT configuration having the least output impedance: Common Collector Configuration

Compare BJT common base configuration with common collector configuration on the basis of (i) Current gain (ii) Voltage gain (iii) Input impedance (iv) Output impedance

Description : Compare BJT common base configuration with common collector configuration on the basis of (i) Current gain (ii) Voltage gain (iii) Input impedance (iv) Output impedance

Last Answer : Parameter Common Base Common Collector Current gain Low (About 1) High (1+β) Voltage gain High 1  Input impedance  Low High Output impedance High Low

Among the three configuration the highest output impedance is obtained by

Last Answer : Among the three configuration, the highest output impedance is obtained by CB.

Which transistor configuration provides a phase reversal between the input and output signals?

Description : Which transistor configuration provides a phase reversal between the input and output signals?

Last Answer : Common emitter.

The input impedance of an op-amp is

Description : The input impedance of an op-amp is • High • Low • Medium • None of the above

Last Answer : The input impedance of an op-amp is High

Harmonic distortion of the signal is produced in an RC coupled transistor amplifier. The probable

Description : Harmonic distortion of the signal is produced in an RC coupled transistor amplifier. The probable component responsible for this distortion is  (A) The transistor itself  (B) the power supply Vcc  (C) the coupling capacitor Cc  (D) the biasing resistors

Last Answer : Harmonic distortion of the signal is produced in an RC coupled transistor amplifier. The probable component responsible for this distortion is The transistor itself 

To conduct an in-circuit test of a transistor, you should use a/an ____________. A. voltmeter or transistor tester B. impedance meter C. ohmmeter or transistor tester D. wattmeter

Description : To conduct an in-circuit test of a transistor, you should use a/an ____________. A. voltmeter or transistor tester B. impedance meter C. ohmmeter or transistor tester D. wattmeter

Last Answer : Answer: A

In order to check the performance of a transistor removed from its circuit, the instrument to be used should be a/an ____________. A. voltmeter or transistor tester B. impedance meter C. ohmmeter or transistor tester D. sensitive potentiometer

Description : In order to check the performance of a transistor removed from its circuit, the instrument to be used should be a/an ____________. A. voltmeter or transistor tester B. impedance meter C. ohmmeter or transistor tester D. sensitive potentiometer

Last Answer : Answer: C

When the initial slope of input sine wave is greater than the slew rate of an OPAMP, the output:

Description : When the initial slope of input sine wave is greater than the slew rate of an OPAMP, the output: (1) Has no offset (2) Approaches to triangular waveshape (3) Is pure sinusoidal (4) Is square wave 

Last Answer : When the initial slope of input sine wave is greater than the slew rate of an OPAMP, the output: Approaches to triangular waveshape

An amplifier without feedback has a voltage gain of 50, input resistance 1kΩ and output resistance of 2.5kΩ.

Description : An amplifier without feedback has a voltage gain of 50, input resistance 1kΩ and output resistance of 2.5kΩ. The input resistance of the current-shunt negative feedback amplifier using the above amplifier with a feedback factor of 0.2 would be: (1) 1/11 kΩ (2) 1/5 kΩ (3) 5 kΩ (4) 11 kΩ

Last Answer : An amplifier without feedback has a voltage gain of 50, input resistance 1kΩ and output resistance of 2.5kΩ. The input resistance of the current-shunt negative feedback amplifier using the above amplifier with a feedback factor of 0.2 would be: 1/11 kΩ

An operational amplifier has an open loop gain of 200,000. Its output exhibits saturation at 10V.

Description : An operational amplifier has an open loop gain of 200,000. Its output exhibits saturation at 10V. The threshold differential voltage of the amplifier is  A) 25 micro-volt B) 50 micro-volt C) 5 Volts D) 10 volts

Last Answer : An operational amplifier has an open loop gain of 200,000. Its output exhibits saturation at 10V. The threshold differential voltage of the amplifier is 50 micro-volt

In Class ‘B’ amplifier, the output current flows for

Description : In Class ‘B’ amplifier, the output current flows for

Last Answer : In Class ‘B’ amplifier, the output current flows for half input cycle

The main function of the transformer used in the output of a power amplifier is

Description : The main function of the transformer used in the output of a power amplifier is  (A) To step up the voltage  (B) to increase the voltage gain  (C) to safeguard the transistor against overheating  (D) to match the load impedance with dynamic output resistance of the transistor

Last Answer : The main function of the transformer used in the output of a power amplifier is to match the load impedance with dynamic output resistance of the transistor

Common base configuration is little used because A) It has low input impedance B) It has high input impedance C) It does not heat up D) It has very high gain.

Description : Common base configuration is little used because A) It has low input impedance B) It has high input impedance C) It does not heat up D) It has very high gain.

Last Answer : A) It has low input impedance

ECL is the fastest of all logic families. High Speed in ECL is possible because transistors are used in difference amplifier configuration, in which they are never driven into ............... (1) Race condition (2) Saturation (3) Delay (4) High impedance

Description : ECL is the fastest of all logic families. High Speed in ECL is possible because transistors are used in difference amplifier configuration, in which they are never driven into ............... (1) Race condition (2) Saturation (3) Delay (4) High impedance

Last Answer : Answer: 2  Explanation: Emitter-coupled logic (ECL) is the fastest of all logic families and therefore is used in applications where very high speed is essential. High speeds have become ... configuration, in which they are never driven into saturation and thereby the storage time is eliminated.

How are amplifiers classified according to the transistor configuration?

Description : How are amplifiers classified according to the transistor configuration?

Last Answer : 1. Common emitter amplifier 2. Common base amplifier 3. Common collector amplifier

Which transistor configuration has the highest input resistance?

Description : Which transistor configuration has the highest input resistance?

Last Answer : Common collector.

Which transistor configuration has a current gain of less than 1?

Description : Which transistor configuration has a current gain of less than 1?

Last Answer : Common base.

Compare between CB , CE & CC transistor configuration.

Description : Compare between CB , CE & CC transistor configuration.

Last Answer : Parameter CB CE CC I/P impedance Low Or 50Ω Medium Or 600Ωto 4kΩ High Or 1 MΩ Current Gain Less than or equal to 1 High Highest Voltage Gain Medium Medium Less ... k Ω to 50 k Ω Low Or 50 Ω Phase shift between input and output 0° 360° 0° 

___________ is device that measures the internal open circuit voltage of an equivalent noise generator having an impedance of 600Ω and delivering noise power to a 600 Ω load. A. Psophometer B. Barometer C. Reflectometer D. Voltmeter

Description : ___________ is device that measures the internal open circuit voltage of an equivalent noise generator having an impedance of 600Ω and delivering noise power to a 600 Ω load. A. Psophometer B. Barometer C. Reflectometer D. Voltmeter

Last Answer : A. Psophometer

What is the input impedance of a transmission line if its characteristic impedance is 300 Ω and the load is 600 Ω? Assume a quarter wavelength section only. A. 150 kΩ B. 150 mΩ C. 150Ω D. 2 Ω

Description : What is the input impedance of a transmission line if its characteristic impedance is 300 Ω and the load is 600 Ω? Assume a quarter wavelength section only. A. 150 kΩ B. 150 mΩ C. 150 Ω D. 2 Ω

Last Answer : C. 150 Ω

What is the effective radiated power of a repeater with 75 watts transmitter power output, 4 dB feedline loss, 3 dB duplexer and circulator loss, and 10 dB antenna gain? A. 600 W B. 75 W C. 18.75 W D. 150 W

Description : What is the effective radiated power of a repeater with 75 watts transmitter power output, 4 dB feedline loss, 3 dB duplexer and circulator loss, and 10 dB antenna gain? A. 600 W B. 75 W C. 18.75 W D. 150 W

Last Answer : D. 150 W

The rotor power output of a 3-phase induction motor is 15 KW and corresponding slip is 4%. The rotor copper loss will be (A) 600 W. (B) 625 W (C) 650 W (D) 700 W

Description : The rotor power output of a 3-phase induction motor is 15 KW and corresponding slip is 4%. The rotor copper loss will be (A) 600 W. (B) 625 W (C) 650 W (D) 700 W

Last Answer : Ans: B Rotor copper losses = rotor input- rotor output and output = (1-s) input ∴ Input = output/(1-s) = 15000 /1-0.04 = 15625 ∴ loss = 15625 -1500 = 625 watt

When you are testing the gain of an audio-frequency transistor with an ohmmeter, what is indicated by a 10-to-1 resistance ratio?

Description : When you are testing the gain of an audio-frequency transistor with an ohmmeter, what is indicated by a 10-to-1 resistance ratio?

Last Answer : Normal gain.

What is the best audio configuration?

Description : What is the best audio configuration?

Last Answer : Cranking up either system or hardware volume is going to result in distortions. I tend to set a general volume with the hardware and try for more precise volume control with the software, even though I know that’s not the relationship between the two.

What gauge of speaker wire should I use to run audio to my subwoofers?

Description : What gauge of speaker wire should I use to run audio to my subwoofers?

Last Answer : # Understand the basics of all car stereo systems. A car stereo system consists of 4 main components and the wiring that connects them. These are the head unit, the main speakers, optional ... speakers. # Step 4 Know about amplifiers. Amplifiers provide extra power to your speakers and/or ext

Are Monitor Audio a good brand of speaker?

Description : Are Monitor Audio a good brand of speaker?

Last Answer : There seems to be no evidence to support this. I am not familiar with their branding let me check right now. Ok, I'm back,apparently they have a storied history of speaker ... a good knowledge of materials because Britain is where we get actual accreditted sound engineers and electricians.

Short-circuited stubs are preferred to open-circuited stubs because thelatter are a. more difficult to make an connect b. made of a transmission line with a different characteristic impedance c. liable to radiate

Description : Short-circuited stubs are preferred to open-circuited stubs because thelatter are a. more difficult to make an connect b. made of a transmission line with a different characteristic impedance c. liable to radiate

Last Answer : c. liable to radiate

Operational amplifiers, used primarily in analog circuits, are characterized by ____________. A. high input impedance, high gain and low output impedance B. high input impedance, high gain and high output impedance C. low input impedance, low gain and high output impedance D. low input impedance, high gain and low output impedance

Description : Operational amplifiers, used primarily in analog circuits, are characterized by ____________. A. high input impedance, high gain and low output impedance B. high input impedance, high gain and high output ... gain and high output impedance D. low input impedance, high gain and low output impedance

Last Answer : Answer: A

Not a reason for the use of an antenna coupler. A. To make the antenna look resistive B. To provide the output amplifier with the correct load impedance C. To discriminate against harmonics D. To prevent re-radiation of the local oscillator

Description : Not a reason for the use of an antenna coupler. A. To make the antenna look resistive B. To provide the output amplifier with the correct load impedance C. To discriminate against harmonics D. To prevent re-radiation of the local oscillator

Last Answer : D. To prevent re-radiation of the local oscillator

Calculated the noise figure of the amplifier whose Req equals 2518Ω (RT=600Ω) if its driven by a generator whose output impedance is 50Ω. A. 39.4 B. 3.94 C. 394 D. 0.394

Description : Calculated the noise figure of the amplifier whose Req equals 2518Ω (RT=600Ω) if its driven by a generator whose output impedance is 50Ω. A. 39.4 B. 3.94 C. 394 D. 0.394

Last Answer : A. 39.4

Termination means A. result of disconnecting a line from a transmitter B. result of cutting both ends of a conductor C. looking back impedance of a line with no load D. load connected to the output end of a transmission line

Description : Termination means A. result of disconnecting a line from a transmitter B. result of cutting both ends of a conductor C. looking back impedance of a line with no load D. load connected to the output end of a transmission line

Last Answer : D. load connected to the output end of a transmission line

Characteristics impedance of a transmission line is the impedance measured at the ___________ when its length is infinite. A. input B. shorted end of the line C. output D. midsection

Description : Characteristics impedance of a transmission line is the impedance measured at the ___________ when its length is infinite. A. input B. shorted end of the line C. output D. midsection

Last Answer : A. input

If the output impedance of an amplifier circuit is decreased, what is the effect on the gain?

Description : If the output impedance of an amplifier circuit is decreased, what is the effect on the gain?

Last Answer : The gain decreases.

What impedance relationship between the output of one circuit and the input of another circuit will provide the maximum power transfer?

Description : What impedance relationship between the output of one circuit and the input of another circuit will provide the maximum power transfer?

Last Answer : Equal impedance.

One ofthe followingis not a reason forthe use of anantenna coupler: a. To make the antenna look resistive b. To provide the output amplifier with the correct load impedance c. To discriminate against harmonics d. To prevent reradiation of the local oscillator

Description : One ofthe followingis not a reason forthe use of anantenna coupler: a. To make the antenna look resistive b. To provide the output amplifier with the correct load impedance c. To discriminate against harmonics d. To prevent reradiation of the local oscillator

Last Answer : d. To prevent reradiation of the local oscillator

What happens to output when a tri-state circuit is selected for high impedance.

Description : What happens to output when a tri-state circuit is selected for high impedance.

Last Answer : Output is disconnected from rest of the circuits by internal circuitry.

Non-inverting amplifier circuits have _______ (a) Very high input impedance (b) very low input impedance (c) low output impedance (d) none of above

Description : Non-inverting amplifier circuits have _______ (a) Very high input impedance (b) very low input impedance (c) low output impedance (d) none of above

Last Answer : (a) Very high input impedance

For JK flipflop J = 0, K=1, the output after clock pulse will be (A) 1. (B) no change. (C) 0. (D) high impedance.

Description : For JK flipflop J = 0, K=1, the output after clock pulse will be (A) 1. (B) no change. (C) 0. (D) high impedance.

Last Answer : Ans: C J=0, K=1, these inputs will reset the flip-flop after the clock pulse. So whatever be the previous output, the next state will be 0.

The output of SR flip flop when S=1, R=0 is (A) 1 (B) 0 (C) No change (D) High impedance

Description : The output of SR flip flop when S=1, R=0 is (A) 1 (B) 0 (C) No change (D) High impedance

Last Answer : Ans: A As for the SR flip-flop S=set input R=reset input ,when S=1, R=0, Flip-flop will be set.

For JK flip flop with J=1, K=0, the output after clock pulse will be (A) 0. (B) 1. (C) high impedance. (D) no change.

Description : For JK flip flop with J=1, K=0, the output after clock pulse will be (A) 0. (B) 1. (C) high impedance. (D) no change.

Last Answer : (B) 1.

A linear network has a current input 4cos(ω t + 20º)A and a voltage output 10 cos(ωt +110º) V. Determine the associated impedance.

Description : A linear network has a current input 4cos(ω t + 20º)A and a voltage output 10 cos(ωt +110º) V. Determine the associated impedance.

Last Answer : Solution

How do I connect my computer's audio to my stereo?

Description : How do I connect my computer's audio to my stereo?

Last Answer : The best connection for your computer's audio to your stereo would be the line out connection on the computer to the auxilary input on the stereo amplifier.

Will audio video cables connect my DVD to my TV?

Description : Will audio video cables connect my DVD to my TV?

Last Answer : When you purchase a DVD player, cables for audio as well as video is also included. All you have to do is connect the audio and video cables to your television and your ready to go.

Why can't my PC connect to my Oontz Angle speaker?

Description : Why can't my PC connect to my Oontz Angle speaker?

Last Answer : Omg I have the same problem and my husband always helps me do it. I’ll ask him when he wakes up. It’s only 4am here. Check to see if there is some sort of button on the speaker and make sure the volume is up. That’s all I can think of now.

How does the use of nonverbal communication such as making eye contact help a speaker connect with audience?

Description : How does the use of nonverbal communication such as making eye contact help a speaker connect with audience?

Last Answer : By making the speaker seem more human and relatable

In a logic circuit the NOR and NAND gate functions ____________. A. must be accomplished with a common base transistor arrangement B. are available in diode form C. are exact opposites with the same NOR and NAND inputs D. have output conditions that are exact opposites to the output condition for OR and AND, respectively

Description : In a logic circuit the NOR and NAND gate functions ____________. A. must be accomplished with a common base transistor arrangement B. are available in diode form C. are exact opposites with the ... . have output conditions that are exact opposites to the output condition for OR and AND, respectively

Last Answer : Answer: D

If the operating point of an NPN transistor amplifier is selected in saturation region, it is likely to result in A) Thermal runaway of transistor B) Clipping of output in the positive half of the input signal C) Need for high dc collector supply D) Clipping of output in the negative half of the input signal

Description : If the operating point of an NPN transistor amplifier is selected in saturation region, it is likely to result in A) Thermal runaway of transistor B) Clipping of output in the positive half of the ... for high dc collector supply D) Clipping of output in the negative half of the input signal

Last Answer : B) Clipping of output in the positive half of the input signal