In a Klystron amplifier, the RF voltage produces

In a Klystron amplifier, the RF voltage produces 

(a) amplitude modulation (b) frequency modulation (c) phase modulation (d) velocity modulation
by

1 Answer

Answer :

In a Klystron amplifier, the RF voltage produces velocity modulation

by

Related questions

An amplifier without feedback has a voltage gain of 50, input resistance 1kΩ and output resistance of 2.5kΩ.

Description : An amplifier without feedback has a voltage gain of 50, input resistance 1kΩ and output resistance of 2.5kΩ. The input resistance of the current-shunt negative feedback amplifier using the above amplifier with a feedback factor of 0.2 would be: (1) 1/11 kΩ (2) 1/5 kΩ (3) 5 kΩ (4) 11 kΩ

Last Answer : An amplifier without feedback has a voltage gain of 50, input resistance 1kΩ and output resistance of 2.5kΩ. The input resistance of the current-shunt negative feedback amplifier using the above amplifier with a feedback factor of 0.2 would be: 1/11 kΩ

The voltage gain of a common base amplifier depends on

Description : The voltage gain of a common base amplifier depends on  1. Load resistor RL 2. input resistance of transistor 3. Ac alpha 4. All the above 

Last Answer : The voltage gain of a common base amplifier depends on  1. Load resistor RL 2. input resistance of transistor 3. Ac alpha 4. All the above 

Just as a voltage amplifier signal voltage a power amplifier.

Description : Just as a voltage amplifier signal voltage a power amplifier.  1.amplifier power  2.amplifier signal  3.converts the signal ac power into DC power  4.converts a dc power into useful AC power 

Last Answer : Just as a voltage amplifier signal voltage a power amplifier.  1.amplifier power  2.amplifier signal  3.converts the signal ac power into DC power  4.converts a dc power into useful AC power 

The closed-loop voltage gain of an inverting amplifier equal to

Last Answer : The closed-loop voltage gain of an inverting amplifier equal to The feedback resistance divided by the input resistance.

Which of the following is one of the possible causes for a slow drift of frequency in a self exited transmitter oscillator circuits resulting to a poor frequency stability? A. Poor soldered connections B. Power supply voltage changes C. Loose connections in the oscillator, amplifier, or antenna circuits D. DC and RF heating of resistors, causing then to change values.

Description : Which of the following is one of the possible causes for a slow drift of frequency in a self exited transmitter oscillator circuits resulting to a poor frequency stability? A. Poor soldered connections ... , or antenna circuits D. DC and RF heating of resistors, causing then to change values.

Last Answer : D. DC and RF heating of resistors, causing then to change values.

What type of klystron is used as the final stage of a power- amplifier transmitter?

Description : What type of klystron is used as the final stage of a power- amplifier transmitter?

Last Answer : Multicavity klystron.

What type of klystron is used as the final stage of a power- amplifier transmitter?

Description : What type of klystron is used as the final stage of a power- amplifier transmitter?

Last Answer : Multicavity klystron.

Describe working of Reflex Klystron amplifier with a neat diagram.

Description : Describe working of Reflex Klystron amplifier with a neat diagram.

Last Answer : Operation: It is assumed that the oscillations are set up in the tube initially due to noise or switching transients and these oscillations are sustained by device operation. ... on the reference electron. These bunch transfer maximum energy to the gap to get sustained oscillations.

In a klystron amplifier the input cavity is called:

Description : In a klystron amplifier the input cavity is called:  (1) Buncher (2) Catcher (3) Pierce gun (4) Collector

Last Answer : In a klystron amplifier the input cavity is called: Buncher.

The unity gain bandwidth of an inverting amplifier is 10 MHz What would be the bandwidth if the gain is

Description : The unity gain bandwidth of an inverting amplifier is 10 MHz What would be the bandwidth if the gain is increased to 10 V/V? A) 100 MHz B) 1 MHz C) 10 MHz D) 1 kHz 

Last Answer : The unity gain bandwidth of an inverting amplifier is 10 MHz What would be the bandwidth if the gain is increased to 10 V/V? A) 100 MHz B) 1 MHz C) 10 MHz D) 1 kHz 

The ideal operational amplifier does not have:

Description : The ideal operational amplifier does not have: (1) Infinite input resistance (2) Infinite output resistance (3) Infinite voltage gain (4) Infinite bandwidth 

Last Answer : The ideal operational amplifier does not have: Infinite output resistance

The gain of an FET amplifier can be changed by changing:

Description : The gain of an FET amplifier can be changed by changing: (1) rm (2) gm (3) Rd (4) None of these

Last Answer : The gain of an FET amplifier can be changed by changing: gm

If the feedback factor of an amplifier is 0.1 and its gain without feedback is 40, then its gain with feedback is

Description : If the feedback factor of an amplifier is 0.1 and its gain without feedback is 40, then its gain with feedback is (a) – 13.3 (b) 200 (c) 8 (d) 10 

Last Answer : If the Feedback Factor of an amplifier is 0.1 and its gain without feedback is 40, then feedback is 40,then its gain with feedback is 8.

A low noise amplifier has an effective noise temperature of 50 k. The absolute noise figure is

Description : A low noise amplifier has an effective noise temperature of 50 k. The absolute noise figure is

Last Answer : A low noise amplifier has an effective noise temperature of 50 k. The absolute noise figure is 1.172

An amplifier operating over the frequency range from 18 to 20 MHz has 10 kilo ohm input resistor. What is

Description : An amplifier operating over the frequency range from 18 to 20 MHz has 10 kilo ohm input resistor. What is the r.m.s. noise voltage at the input to this amplifier if the ambient temperature is 27o C

Last Answer : An amplifier operating over the frequency range from 18 to 20 MHz has 10 kilo ohm input resistor. What is the r.m.s. noise voltage at the input to this amplifier if the ambient temperature is 27o C 18.2 microvolt

For a feedback amplifier, if the loop gain is much greater than unity, the closed loop gain will be equal to

Description : For a feedback amplifier, if the loop gain is much greater than unity, the closed loop gain will be equal to

Last Answer : For a feedback amplifier, if the loop gain is much greater than unity, the closed loop gain will be equal to inverse of feedback factor

For Cascode amplifier the output impedance becomes

Description : For Cascode amplifier the output impedance becomes 

Last Answer : For Cascode amplifier the output impedance becomes very high

An amplifier without feedback has a gain of 1000. The gain with a negative feedback of 0.009 is

Description : An amplifier without feedback has a gain of 1000. The gain with a negative feedback of 0.009 is  A) 10 B) 100 C) 125 D) 900

Last Answer : 100

An operational amplifier has an open loop gain of 200,000. Its output exhibits saturation at 10V.

Description : An operational amplifier has an open loop gain of 200,000. Its output exhibits saturation at 10V. The threshold differential voltage of the amplifier is  A) 25 micro-volt B) 50 micro-volt C) 5 Volts D) 10 volts

Last Answer : An operational amplifier has an open loop gain of 200,000. Its output exhibits saturation at 10V. The threshold differential voltage of the amplifier is 50 micro-volt

In a radio receiver the IF amplifier

Description : In a radio receiver the IF amplifier  (A) is tuned above the stations incoming frequency (B) amplifies the output of local oscillator (C) is fixed tuned to one particular frequency (D) can be tuned to various isolate frequencies

Last Answer : In a radio receiver the IF amplifier is fixed tuned to one particular frequency

Class A amplifier is used when

Description : Class A amplifier is used when  (A) No phase inversion is required (B) Highest voltage gain is required (C) dc voltages are to be amplified (D) Minimum distortion is desired. 

Last Answer : Class A amplifier is used when Minimum distortion is desired. 

Negative feedback amplifier has a signal corrupted by noise as its input. The amplifier will

Description : Negative feedback amplifier has a signal corrupted by noise as its input. The amplifier will   (A) Amplify the noise as much as the signal (B) Reduce the noise (C) Increase the noise (D) Not effect the noise

Last Answer : Negative feedback amplifier has a signal corrupted by noise as its input. The amplifier will Reduce the noise

In an IF amplifier, the IF transformer is provided with tapping to

Description : In an IF amplifier, the IF transformer is provided with tapping to  (a) increase the voltage gain (b) increase the bandwidth of the resonance circuit (c) increase the impedance ... resonance circuit to the following cascaded amplifier (d) increase the quality factor of the resonance circuit 

Last Answer : In an IF amplifier, the IF transformer is provided with tapping to increase the voltage gain

In class - A power amplifier, the collector dissipation is maximum when

Description : In class - A power amplifier, the collector dissipation is maximum when  (a) no signal is present  (b) signal swing is maximum  (c) signal swing is (1/1.414) of its maximum  (d) none of the above

Last Answer : In class - A power amplifier, the collector dissipation is maximum when no signal is present

In Class ‘B’ amplifier, the output current flows for

Description : In Class ‘B’ amplifier, the output current flows for

Last Answer : In Class ‘B’ amplifier, the output current flows for half input cycle

The efficiency of a class B push-pull amplifier is

Description : The efficiency of a class B push-pull amplifier is

Last Answer : The efficiency of a class B push-pull amplifier is 75-80%

Which of the following amplifier has the least distortion.

Description : Which of the following amplifier has the least distortion. • Class E • Class D • Class C • Class A

Last Answer : Which of the following amplifier has the least distortion. • Class E • Class D • Class C • Class A

The battery operated pre-amplifier with a consumption of 10 Watts can work on battery of 12

Description : The battery operated pre-amplifier with a consumption of 10 Watts can work on battery of 12 volt, 100 AH having efficiency of 50% for • 120 hrs. • 60 hrs. • 100 hrs. • 10 hrs.

Last Answer : The battery operated pre-amplifier with a consumption of 10 Watts can work on battery of 12 volt, 100 AH having efficiency of 50% for 60 hrs.

In class-A amplifier conduction extends over 360° because the operating point.

Description : In class-A amplifier conduction extends over 360° because the operating point.  1. Located near saturation point 2. Located at or near cut-off point 3. Located on load line 4. Located in the centre of load line 

Last Answer : In class-A amplifier conduction extends over 360° because the operating point.  1. Located near saturation point 2. Located at or near cut-off point 3. Located on load line 4. Located in the centre of load line 

Harmonic distortion of the signal is produced in an RC coupled transistor amplifier. The probable

Description : Harmonic distortion of the signal is produced in an RC coupled transistor amplifier. The probable component responsible for this distortion is  (A) The transistor itself  (B) the power supply Vcc  (C) the coupling capacitor Cc  (D) the biasing resistors

Last Answer : Harmonic distortion of the signal is produced in an RC coupled transistor amplifier. The probable component responsible for this distortion is The transistor itself 

The main component responsible for the fall of gain of an RC coupled amplifier in low frequency

Description : The main component responsible for the fall of gain of an RC coupled amplifier in low frequency range is  (A) The active device itself (tube, or transistor)  (B) stray shunt capacitance Cs  (C) the grid leak resistance Rg  (D) coupling capacitor Cc

Last Answer : The main component responsible for the fall of gain of an RC coupled amplifier in low frequency range is coupling capacitor Cc

The main function of the transformer used in the output of a power amplifier is

Description : The main function of the transformer used in the output of a power amplifier is  (A) To step up the voltage  (B) to increase the voltage gain  (C) to safeguard the transistor against overheating  (D) to match the load impedance with dynamic output resistance of the transistor

Last Answer : The main function of the transformer used in the output of a power amplifier is to match the load impedance with dynamic output resistance of the transistor

Negative feedback in an amplifier is accompanied by

Description : Negative feedback in an amplifier is accompanied by (A) Gain less sensitive to component variations (B) Increase in gain (C) Decrease in bandwidth (D) None of the above

Last Answer : Negative feedback in an amplifier is accompanied by Gain less sensitive to component variations 

What is the importance of negative feedback in the operational amplifier?

Description : What is the importance of negative feedback in the operational amplifier? (A) It maintains the gain (B) The voltage difference between the input terminals is maintained at a very small value ( ... value (D) The voltage difference between the input terminals is maintained at a very high value

Last Answer : The voltage difference between the input terminals is maintained at a very small value

Calculate the noise figure of the receiver whose RF amplifier has an input resistance of 1000Ω and an equivalent shot-noise resistance of 2000Ω, a gain of 25 and load resistance of 125 kΩ. Given that the bandwidth is 1.0MHz and the temperature is 20˚C, and that the receiver is connected to an antenna with an impedance of 75Ω. A. 30.3 B. 3.03 C. 303 D. .303

Description : Calculate the noise figure of the receiver whose RF amplifier has an input resistance of 1000Ω and an equivalent shot-noise resistance of 2000Ω, a gain of 25 and load resistance of 125 kΩ. Given that the bandwidth is 1. ... to an antenna with an impedance of 75Ω. A. 30.3 B. 3.03 C. 303 D. .303

Last Answer : A. 30.3

When measuring a transmitter’s frequency against a suitable standard, the frequency to be measured is taken from the A. oscillator stage B. intermediate amplifier C. buffer stage D. final RF stage

Description : When measuring a transmitter’s frequency against a suitable standard, the frequency to be measured is taken from the A. oscillator stage B. intermediate amplifier C. buffer stage D. final RF stage

Last Answer : D. final RF stage

What is the meaning of forward power? A. The power traveling from the transmitter to the antenna. B. The power radiated from the top of an antenna system. C. The power produced during the positive half of an RF cycle. D. The power used to drive a linear amplifier.

Description : What is the meaning of forward power? A. The power traveling from the transmitter to the antenna. B. The power radiated from the top of an antenna system. C. The power produced during the positive half of an RF cycle. D. The power used to drive a linear amplifier.

Last Answer : A. The power traveling from the transmitter to the antenna.

What establishes the receiver bandwidth? A. RF amplifier B. Mixer C. Local oscillator D. IF amplifier

Description : What establishes the receiver bandwidth? A. RF amplifier B. Mixer C. Local oscillator D. IF amplifier

Last Answer : D. IF amplifier

What consists the front-end circuit of a VHF TV superheterodyne receiver? A. Mixer, RF amplifier and AFC? B. RF amplifier, Band pass filter and mixer C. Local oscillator, mixer and RF amplifier D. Local oscillator, AGC and antenna

Description : What consists the front-end circuit of a VHF TV superheterodyne receiver? A. Mixer, RF amplifier and AFC? B. RF amplifier, Band pass filter and mixer C. Local oscillator, mixer and RF amplifier D. Local oscillator, AGC and antenna

Last Answer : C. Local oscillator, mixer and RF amplifier

One of the following is a high powered RF ac basic transmitter that has two or more stages, the oscillator stage which determines the frequency opereation and RF amplifier stage orstages that develop the high power output. The purpose of which is to develop a good frequency stability. A. Goldsmith B. MOPA C. Alexanderson D. Hartley

Description : One of the following is a high powered RF ac basic transmitter that has two or more stages, the oscillator stage which determines the frequency opereation and RF amplifier stage orstages that develop the ... to develop a good frequency stability. A. Goldsmith B. MOPA C. Alexanderson D. Hartley

Last Answer : B. MOPA

Which of the following parts of the radio receiver represent the component that extracts the desire RF signal from the electromagnetic wave? A. AF amplifier B. Antenna C. Detector D. Crystal

Description : Which of the following parts of the radio receiver represent the component that extracts the desire RF signal from the electromagnetic wave? A. AF amplifier B. Antenna C. Detector D. Crystal

Last Answer : B. Antenna

One of the following is a possible cause of an abrupt frequency variation in a self exited transmitter oscillator circuits resulting to a poor frequency stability to hold a constant frequency oscillation. A. Heating and expansion of oscillator coil B. DC and RF ac heating of resistors which cause change in values C. Heating of capacitor in the oscillatorD. Loose connections in the oscillator, amplifier, or antenna circuits.

Description : One of the following is a possible cause of an abrupt frequency variation in a self exited transmitter oscillator circuits resulting to a poor frequency stability to hold a constant frequency ... capacitor in the oscillator D. Loose connections in the oscillator, amplifier, or antenna circuits.

Last Answer : D. Loose connections in the oscillator, amplifier, or antenna circuits.

Refers to one of the front end circuit of a VHF TV superheterodyne receiver which is usually a separate circuit coupled to the mixer. A. Antenna feed B. AGC C. RF amplifier D. Local oscillator

Description : Refers to one of the front end circuit of a VHF TV superheterodyne receiver which is usually a separate circuit coupled to the mixer. A. Antenna feed B. AGC C. RF amplifier D. Local oscillator

Last Answer : D. Local oscillator

After the IF stages have been aligned, the next stage to align in FM receiver is. A. local oscillator B. limiter stage C. RF amplifier D. mixer stage

Description : After the IF stages have been aligned, the next stage to align in FM receiver is. A. local oscillator B. limiter stage C. RF amplifier D. mixer stage

Last Answer : A. local oscillator

Which of the following methods cannot be used to increase the bandwidth for cascaded RF amplifier stages? A) Wave traps in each stage B) Stagger tuning C) A shunt damping resistor across each tuned circuit D) Doubled tuned transformers with tighter coupling

Description : Which of the following methods cannot be used to increase the bandwidth for cascaded RF amplifier stages? A) Wave traps in each stage B) Stagger tuning C) A shunt damping resistor across each tuned circuit D) Doubled tuned transformers with tighter coupling

Last Answer : A) Wave traps in each stage

What two methods are used to compensate for the problems that cause low gain in an rf amplifier?

Description : What two methods are used to compensate for the problems that cause low gain in an rf amplifier?

Last Answer : . RF transformers are used and the transistor is neutralized.

What problem is caused in an rf amplifier by a loosely coupled transformer?

Description : What problem is caused in an rf amplifier by a loosely coupled transformer?

Last Answer : A too-narrow bandpass.

What is the most common form of coupling for an rf amplifier?

Description : What is the most common form of coupling for an rf amplifier?

Last Answer : Transformer coupling.

Can a parallel LC circuit be used as the frequency determining network for an rf amplifier?

Description : Can a parallel LC circuit be used as the frequency determining network for an rf amplifier?

Last Answer : Yes.

What is the purpose of a frequency-determining network in an rf amplifier?

Description : What is the purpose of a frequency-determining network in an rf amplifier?

Last Answer : To provide maximum impedance at the desired frequency.