What is the purpose of R2?

What is the purpose of R2?
by

1 Answer

Answer :

R2 provides the proper bias to the emitter of Q1
by

Related questions

When an unknown capacitance is tested with a bridge, what is the value of Cx if R1 equals 70 ohms, R2 equals 150 ohms, and Cs equals 550 microfarads?

Description : When an unknown capacitance is tested with a bridge, what is the value of Cx if R1 equals 70 ohms, R2 equals 150 ohms, and Cs equals 550 microfarads?

Last Answer : 256 microfarads.

When a bridge is used to measure resistance, what is the value of Rx if R1 equals 80 ohms, R2 equals 120 ohms, and R3 equals 280 ohms?

Description : When a bridge is used to measure resistance, what is the value of Rx if R1 equals 80 ohms, R2 equals 120 ohms, and R3 equals 280 ohms?

Last Answer : 420 ohms.

In a circuit such as that shown in figure 3-16, if R1 has a value of 50 ohms and R2 has a value of 250 ohms and the input signal has a value of +10 millivolts, what is the value of the output signal?

Description : In a circuit such as that shown in figure 3-16, if R1 has a value of 50 ohms and R2 has a value of 250 ohms and the input signal has a value of +10 millivolts, what is the value of the output signal?

Last Answer : 60 millivolts.

In a circuit such as that shown in figure 3-15, if R1 has a value of 100 ohms and R2 has a value of 1 kilohm and the input signal is at a value of + 5 millivolts, what is the value of the output signal?

Description : In a circuit such as that shown in figure 3-15, if R1 has a value of 100 ohms and R2 has a value of 1 kilohm and the input signal is at a value of + 5 millivolts, what is the value of the output signal?

Last Answer : 50 millivolts.

how is (a) the current through R2 and (b) the voltage drop across R2 computed?

Description : how is (a) the current through R2 and (b) the voltage drop across R2 computed?

Last Answer : (a) By adding the bleeder current (IR1) and the current through load 1(b) By subtracting the voltage of load 1 from the voltage of load 2.

A series circuit consists of two resistors in series. R1 = 25 ohms and R2 = 30 ohms. The circuit current is 6 amps. What is the (a) source voltage, (b) voltage dropped by each resistor, (c) total power, and (d) power used by each resistor?

Description : A series circuit consists of two resistors in series. R1 = 25 ohms and R2 = 30 ohms. The circuit current is 6 amps. What is the (a) source voltage, (b) voltage dropped by each resistor, (c) total power, and (d) power used by each resistor?

Last Answer : (a) 330 volts. (b) E1 = 150 volts. E2 = 180 volts. (c) 1.98 kilowatts. (d) P1 = 900 watts. P2 = 1.08 kilowatts component but in a parallel circuit total current divides among the available paths.

What would the source voltage (ES) in figure 3-39 be if the current through R2 were 2 milliamps?

Description : What would the source voltage (ES) in figure 3-39 be if the current through R2 were 2 milliamps?

Last Answer : 60 volts.

A series circuit consisting of three resistors has a current of 3 amps. If R1 = 20 ohms, R2= 60 ohms, and R 3 = 80 ohms, what is the (a) total resistance and (b) source voltage of the circuit?

Description : A series circuit consisting of three resistors has a current of 3 amps. If R1 = 20 ohms, R2= 60 ohms, and R 3 = 80 ohms, what is the (a) total resistance and (b) source voltage of the circuit?

Last Answer : (a) 160 ohms. (b) 480 ohms

Why can I not install MS SQL Server Express 2008 R2?

Description : Why can I not install MS SQL Server Express 2008 R2?

Last Answer : Please provide details on what and how it fails the precheck.

In Star Wars, why is the bartender at the Mos Isley spaceport cantina so hostile ("we don't serve their kind here") towards C3PO and R2-D2?

Description : In Star Wars, why is the bartender at the Mos Isley spaceport cantina so hostile ("we don't serve their kind here") towards C3PO and R2-D2?

Last Answer : Probably just to show that even a long time ago in a galaxy far far away, racism still exists.

A sphere of radius r is cut from larger sphere of radius R. The distance between their centre is a. The centroid of the remaining valoume lies on the line of centres and the sistanc from the centre of the larger sphere is a.ar2 / (R2 - r2) b.107 dynes c.aR/(R2-r2) d.aR/(R - r) e.ar3 / (R3 - r3)

Description : A sphere of radius r is cut from larger sphere of radius R. The distance between their centre is a. The centroid of the remaining valoume lies on the line of centres and the sistanc from the centre of the larger sphere is a.ar2 / (R2 - r2) b.107 dynes c.aR/(R2-r2) d.aR/(R - r) e.ar3 / (R3 - r3)

Last Answer : e. ar3 / (R3 - r3)

The radius of gyration of a solid sphere of radius r is equal to a.0.8 r2 b.0.2 r2 c.0.3 r2 d.0.4 r2 e.0.5 r2

Description : The radius of gyration of a solid sphere of radius r is equal to a.0.8 r2 b.0.2 r2 c.0.3 r2 d.0.4 r2 e.0.5 r2

Last Answer : d. 0.4 r2

The moment of inertia of a semi-circle of radius r with respect to a centroidal axis parallel to the diameter is a.0.33 r2 b.0.11 r2 c.0.055 r2 d.0.05 r2 e.0.22 r2

Description : The moment of inertia of a semi-circle of radius r with respect to a centroidal axis parallel to the diameter is a.0.33 r2 b.0.11 r2 c.0.055 r2 d.0.05 r2 e.0.22 r2

Last Answer : b. 0.11 r2

Let R1 and R2 be the remainders when the polynomials x^3 + 2x^2 – 5ax – 7 and x^2 + ax^2 – 12x + 6 are divided by (x + 1) and (x – 2) respectively. -Maths 9th

Description : Let R1 and R2 be the remainders when the polynomials x^3 + 2x^2 – 5ax – 7 and x^2 + ax^2 – 12x + 6 are divided by (x + 1) and (x – 2) respectively. -Maths 9th

Last Answer : answer:

What is R2-D2's name often shortened to?

Description : What is R2-D2's name often shortened to?

Last Answer : R2-D2 is often referred to as R2

What is The area of a circle depending on the radius. Use the equation A(r) r2 to compute A(7). Round your answer to the nearest hundredth.?

Description : What is The area of a circle depending on the radius. Use the equation A(r) r2 to compute A(7). Round your answer to the nearest hundredth.?

Last Answer : The area of a circle is: pi times radius squared

What is The area of a circle depending on the radius. Use the equation A(r) r2 to compute A(7). Round your answer to the nearest hundredth.?

Description : What is The area of a circle depending on the radius. Use the equation A(r) r2 to compute A(7). Round your answer to the nearest hundredth.?

Last Answer : The area of a circle is: pi times radius squared

What is the Voltage drop of R1 If V 10 Volts R1 500 Ohms and R2 1500 Ohms?

Description : What is the Voltage drop of R1 If V 10 Volts R1 500 Ohms and R2 1500 Ohms?

Last Answer : You need to mention whether the resistors are in series or parallel to get the right answer

What is the total current is V is 10 Volts R1 is 500 Ohms and R2 is 1500 ohms?

Description : What is the total current is V is 10 Volts R1 is 500 Ohms and R2 is 1500 ohms?

Last Answer : We need to find R equivalent at first then divide V from it to find the total current.Case 1: If resistances are connected in series.Then, R(eq.) = R1 + R2 = 500 + 1500 = 2000 ohmSo, Total current, I = V/R(eq.) = ... (500 + 1500) = 400 ohmSo, Total current, I = V/R(eq.) = 10/400 = 1/40 or 0.025 A.

What is the total resistance is V is 10 volts R1 is 1000 ohms and R2 is 1000 Ohms?

Description : What is the total resistance is V is 10 volts R1 is 1000 ohms and R2 is 1000 Ohms?

Last Answer : If they're connected in series the total resistance is 2000 ohms. If they're connected in parallel the resistance is 500 ohms.

Two planets have the same density of matter, such that their masses are proportional to the cube of their radii. The ratio of their acceleration due to gravity on their surfaces is (a) r2/r1 (b) (r1/r2)2 (c) r1/r2 (d) (r2/r1)2

Description : Two planets have the same density of matter, such that their masses are proportional to the cube of their radii. The ratio of their acceleration due to gravity on their surfaces is (a) r2/r1 (b) (r1/r2)2 (c) r1/r2 (d) (r2/r1)2

Last Answer : Ans:(d) Direction: In the following question, a statement of Assertion (A) is given followed by corresponding Reason (R), just below it. Read the statements carefully and mark the correct answer: (a) If both A and ... true but R is not the correct explanation of A. (c) If A is true but R is false

If is the rugosity coefficient, is the bed slope of sewer, the velocity of flow in m/sec may be obtained by the formula V = (1/n) r2/3 s1/2 evolved by A. Chezy B. Manning C. Bazin D. Kutter

Description : If is the rugosity coefficient, is the bed slope of sewer, the velocity of flow in m/sec may be obtained by the formula V = (1/n) r2/3 s1/2 evolved by A. Chezy B. Manning C. Bazin D. Kutter

Last Answer : ANS: B

The formula V = (1/n) r2/3 A. Chezy’s formula B. Bazin’s formula C. Kutter’s formula D. Manning’s formula

Description : The formula V = (1/n) r2/3 A. Chezy’s formula B. Bazin’s formula C. Kutter’s formula D. Manning’s formula

Last Answer : ANS: D

weight of water, the hydraulic mean depth of the sewer and the bed slope w is the unit of the sewer, then the tractive force exerted by flowing water, is A. w r S S B. w r1/2 C. w r S D. w r2/3

Description : weight of water, the hydraulic mean depth of the sewer and the bed slope w is the unit of the sewer, then the tractive force exerted by flowing water, is A. w r S S B. w r1/2 C. w r S D. w r2/3

Last Answer : ANS: A

What is the total current of the illustrated circuit if the battery is 12 VDC and the resistance of R1 is 2 ohms, R2 is 3 ohms and R3 is 6 ohms? EL-0021 A. 2 amps B. 4 amps C. 6 amps D. 12 amps

Description : What is the total current of the illustrated circuit if the battery is 12 VDC and the resistance of R1 is 2 ohms, R2 is 3 ohms and R3 is 6 ohms? EL-0021 A. 2 amps B. 4 amps C. 6 amps D. 12 amps

Last Answer : Answer: D

In the illustrated circut, if the resistance of R1 is 10 ohms, R2 is 10 ohms, and R3 is 10 ohms. What is the total resistance? EL-0032 A. 15 ohms B. 20 ohms C. 25 ohms D. 30 ohms

Description : In the illustrated circut, if the resistance of R1 is 10 ohms, R2 is 10 ohms, and R3 is 10 ohms. What is the total resistance? EL-0032 A. 15 ohms B. 20 ohms C. 25 ohms D. 30 ohms

Last Answer : Answer: A

The electrical diagram shown in the illustration shows _____________. EL-0021 A. 'R1', 'R2', and 'R3' are connected is series B. 'R1', 'R2', and 'R3' are connected in parallel C. the voltages measured across 'R1', 'R2' and 'R3' will be different if 'R1', 'R2' and 'R3' have different values D. the total resistance equals R1 + R2 + R3

Description : The electrical diagram shown in the illustration shows _____________. EL-0021 A. 'R1', 'R2', and 'R3' are connected is series B. 'R1', 'R2', and 'R3' are connected in parallel C. the voltages measured across ... if 'R1', 'R2' and 'R3' have different values D. the total resistance equals R1 + R2 + R3

Last Answer : Answer: B

Which of the following statements is correct for the illustrated circuit? EL-0020 A. 'R1', 'R2', and 'R3' are connected in series. B. 'R1', 'R2', and 'R3' are connected in parallel. C. The voltages measured across 'R1', 'R2', and 'R3' are equal. D. The total resistance equals 1/R1 + 1/R2 + 1/R

Description : Which of the following statements is correct for the illustrated circuit? EL-0020 A. 'R1', 'R2', and 'R3' are connected in series. B. 'R1', 'R2', and 'R3' are connected in parallel. C. The voltages measured across 'R1', 'R2', and 'R3' are equal. D. The total resistance equals 1/R1 + 1/R2 + 1/R

Last Answer : Answer: A

As shown in the illustration, if 'R1' and 'R2' have unequal values, the ____________. EL-0019 A. voltage drop across 'R1' will not be equal to the voltage drop across 'R2' B. current flow through 'R1' will equal the current flow through 'R2' C. the energy dissipated in 'R1' will be the same as the energy dissipated in 'R2' D. current flow through 'R1' will differ from the current flow through 'R2'

Description : As shown in the illustration, if 'R1' and 'R2' have unequal values, the ____________. EL-0019 A. voltage drop across 'R1' will not be equal to the voltage drop across 'R2' B. current flow ... energy dissipated in 'R2' D. current flow through 'R1' will differ from the current flow through 'R2'

Last Answer : Answer: D

If coils 'R1-R2-R3' at the receiver of figure 'B' shown in the illustration turned opposite of those in the transmitter by design, what corrective action should be taken? EL-0092 A. Reverse the 60 Hz supply connections to 'S1' and 'S2'. B. No action is needed. C. Interchange leads 'R1' and 'R3'. D. Interchange leads 'R2' and 'R3'.

Description : If coils 'R1-R2-R3' at the receiver of figure 'B' shown in the illustration turned opposite of those in the transmitter by design, what corrective action should be taken? EL-0092 A. Reverse the 60 Hz supply ... is needed. C. Interchange leads 'R1' and 'R3'. D. Interchange leads 'R2' and 'R3'.

Last Answer : Answer: B

As shown in the illustration if the applied voltage is 12 VDC, the resistance of R1 is 24 kohms, and R2 is 3610 ohms what is the current flowing through R1? EL-0036 A. .434 milliamps B. .005 amp C. 6.00 amps D. 2.4 milliamps

Description : As shown in the illustration if the applied voltage is 12 VDC, the resistance of R1 is 24 kohms, and R2 is 3610 ohms what is the current flowing through R1? EL-0036 A. .434 milliamps B. .005 amp C. 6.00 amps D. 2.4 milliamps

Last Answer : Answer: A

As shown in the illustration if the applied voltage is 12 VDC, the resistance of R1 is 10 ohms, and R2 is 10 ohms what is the total power consumed by R1? EL-0036 A. 3.6 watts B. 72 watts C. 7.2 watts D. 36 watts

Description : As shown in the illustration if the applied voltage is 12 VDC, the resistance of R1 is 10 ohms, and R2 is 10 ohms what is the total power consumed by R1? EL-0036 A. 3.6 watts B. 72 watts C. 7.2 watts D. 36 watts

Last Answer : Answer: A

As shown in the illustration if the applied voltage is 12 VDC, the resistance of R1 is 10 ohms, and R2 is 10 ohms what is the total power consumed by the circuit? EL-0036 A. 3.6 watts B. 72 watts C. 7.2 watts D. 36 watts

Description : As shown in the illustration if the applied voltage is 12 VDC, the resistance of R1 is 10 ohms, and R2 is 10 ohms what is the total power consumed by the circuit? EL-0036 A. 3.6 watts B. 72 watts C. 7.2 watts D. 36 watts

Last Answer : Answer: C

As shown in the illustration if the applied voltage is 12 VDC, the resistance of R1 is 10 ohms, and R2 is 10 ohms what is the current flowing through R1? EL-0036 A. 0.6 amp B. 0.833 amp C. 1.2 amps D. 2.4 amps

Description : As shown in the illustration if the applied voltage is 12 VDC, the resistance of R1 is 10 ohms, and R2 is 10 ohms what is the current flowing through R1? EL-0036 A. 0.6 amp B. 0.833 amp C. 1.2 amps D. 2.4 amps

Last Answer : Answer: A

In the illustration, 24 volts is applied to the circut where the resistance for R1 is 3 ohms, R2 is 4 ohms, and R3 is 5 ohms. What is the power consumed in R3? EL-0020 A. 12 watts B. 20 watts C. 24 watts D. 48 watts

Description : In the illustration, 24 volts is applied to the circut where the resistance for R1 is 3 ohms, R2 is 4 ohms, and R3 is 5 ohms. What is the power consumed in R3? EL-0020 A. 12 watts B. 20 watts C. 24 watts D. 48 watts

Last Answer : Answer: B

In the illustration, 24 volts is applied to the circuit where the resistance for R1 is 3 ohms, R2 is 4 ohms, and R3 is 5 ohms. What is the power consumed in R2? EL-0020 A. 16 watts B. 20 watts C. 24 watts D. 28 watts

Description : In the illustration, 24 volts is applied to the circuit where the resistance for R1 is 3 ohms, R2 is 4 ohms, and R3 is 5 ohms. What is the power consumed in R2? EL-0020 A. 16 watts B. 20 watts C. 24 watts D. 28 watts

Last Answer : Answer: A

As shown in the illustration if the applied voltage is 12 VDC, the resistance of R1 is 10 ohms, and R2 is 10 ohms what is the total current in the circuit? EL-0036 A. 0.6 amp B. 0.833 amp C. 1.2 amps D. 2.4 amps

Description : As shown in the illustration if the applied voltage is 12 VDC, the resistance of R1 is 10 ohms, and R2 is 10 ohms what is the total current in the circuit? EL-0036 A. 0.6 amp B. 0.833 amp C. 1.2 amps D. 2.4 amps

Last Answer : Answer: A

In the illustration, 12 volts is applied to the circuit where the resistance of R1 is 10 ohms and R2 is 10 ohms. what is the voltage across R2? EL-0036 A. 1.2 volts B. 2 volts C. 6 volts D. 12 volts

Description : In the illustration, 12 volts is applied to the circuit where the resistance of R1 is 10 ohms and R2 is 10 ohms. what is the voltage across R2? EL-0036 A. 1.2 volts B. 2 volts C. 6 volts D. 12 volts

Last Answer : Answer: C

In the illustration, 24 volts is applied to the circuit where the resistance of R1 is 3 ohms, R2 is 4 ohms, and R3 is 5 ohms. What is the power consumed in R1? EL-0020 A. 2 watts B. 3 watts C. 6 watts D. 12 watts

Description : In the illustration, 24 volts is applied to the circuit where the resistance of R1 is 3 ohms, R2 is 4 ohms, and R3 is 5 ohms. What is the power consumed in R1? EL-0020 A. 2 watts B. 3 watts C. 6 watts D. 12 watts

Last Answer : Answer: D

As shown in the illustration if the applied voltage is 12 VDC, the resistance of R1 is 110 ohms, and R2 is 10 kohms what is the total power consumed by the circuit? EL-0036 A. 3.6 watts B. 72 watts C. .0011286 watts D. .014243 watts

Description : As shown in the illustration if the applied voltage is 12 VDC, the resistance of R1 is 110 ohms, and R2 is 10 kohms what is the total power consumed by the circuit? EL-0036 A. 3.6 watts B. 72 watts C. .0011286 watts D. .014243 watts

Last Answer : Answer: D

As shown in the illustration if the applied voltage is 12 VDC, the resistance of R1 is 110 ohms, and R2 is 10 kohms what is the voltage measured across R1 EL-0036 A. 11.86 volts B. .131 volts C. 12 volts D. .673 volts

Description : As shown in the illustration if the applied voltage is 12 VDC, the resistance of R1 is 110 ohms, and R2 is 10 kohms what is the voltage measured across R1 EL-0036 A. 11.86 volts B. .131 volts C. 12 volts D. .673 volts

Last Answer : Answer: B

In the illustrated circuit, what is the voltage of the battery if the resistance of R1 is 150 ohms, the total resistance is 250 ohms and the current though R2 is 25 milliamps? EL-0036 A. 12 volts B. 24 volts C. 1.5 volts D. 6.25 volts

Description : In the illustrated circuit, what is the voltage of the battery if the resistance of R1 is 150 ohms, the total resistance is 250 ohms and the current though R2 is 25 milliamps? EL-0036 A. 12 volts B. 24 volts C. 1.5 volts D. 6.25 volts

Last Answer : Answer: D

In the illustrated circuit, what is the resistance across R2 if the battery voltage is 32 VDC, the resistance of R1 is 1.2 kohms and the current through R2 is 18.82 milliamps? EL-0036 A. 500 ohms B. 1,200 ohms C. 10 ohms D. The answer can not be found with the information given.

Description : In the illustrated circuit, what is the resistance across R2 if the battery voltage is 32 VDC, the resistance of R1 is 1.2 kohms and the current through R2 is 18.82 milliamps? EL-0036 A. 500 ohms B. 1,200 ohms C. 10 ohms D. The answer can not be found with the information given.

Last Answer : Answer: A

In the illustrated circuit, what is the voltage measured across R1 if the battery is 24 volts, the resistance of R1 is 34 ohms, and the resistance of R2 is 126 ohms? EL-0036 A. 24 volts B. 18.9 volts C. 5.1 volts D. 150 millivolts

Description : In the illustrated circuit, what is the voltage measured across R1 if the battery is 24 volts, the resistance of R1 is 34 ohms, and the resistance of R2 is 126 ohms? EL-0036 A. 24 volts B. 18.9 volts C. 5.1 volts D. 150 millivolts

Last Answer : Answer: C

What is the total resistance of the electrical circuit illustrated if the resistance of R1 is 2 ohms, R2 is 4 ohms, and R3 is 4 ohms with a 6 volt battery? EL-0021 A. 0.01 ohms B. 0.10 ohms C. 1.00 ohms D. 10.00 ohms

Description : What is the total resistance of the electrical circuit illustrated if the resistance of R1 is 2 ohms, R2 is 4 ohms, and R3 is 4 ohms with a 6 volt battery? EL-0021 A. 0.01 ohms B. 0.10 ohms C. 1.00 ohms D. 10.00 ohms

Last Answer : Answer: C

The illustrated circuit is a wheatstone bridge. If the meter 'G' reads 0 with the switch closed then ________. EL-0024 A. the current through R1 - R2 is equal to the current through R3 - Rx B. the voltage across b - d is equal to the voltage of E C. the resistance of Rx is equal to the resistance of R2 D. all the above are true

Description : The illustrated circuit is a wheatstone bridge. If the meter 'G' reads 0 with the switch closed then ________. EL-0024 A. the current through R1 - R2 is equal to the current through R3 - Rx B. the voltage ... of E C. the resistance of Rx is equal to the resistance of R2 D. all the above are true

Last Answer : Answer: A

If a voltage of 125 VDC is applied to the illustrated circuit where the resistance of R1 is 12 ohms, and R2 is 115 ohms, the current will be_______. EL-0019 A. 11.5 amps B. 12.5 amps C. 115 amps D. 125 amps

Description : If a voltage of 125 VDC is applied to the illustrated circuit where the resistance of R1 is 12 ohms, and R2 is 115 ohms, the current will be_______. EL-0019 A. 11.5 amps B. 12.5 amps C. 115 amps D. 125 amps

Last Answer : Answer: A

In the illustrated circuit, what is the total resistance if the voltage is 10 VDC, the resistance of R2 is 40 ohms and the total current is .75 amps? EL-0019 A. 13 1/3 ohms B. 20 ohms C. 60 ohms D. the answer can not be determined from the information given

Description : In the illustrated circuit, what is the total resistance if the voltage is 10 VDC, the resistance of R2 is 40 ohms and the total current is .75 amps? EL-0019 A. 13 1/3 ohms B. 20 ohms C. 60 ohms D. the answer can not be determined from the information given

Last Answer : Answer: A

In the illustrated circuit, what is the resistance of R2 if the total current is .75 amps, the voltage is 12 VDC and the resistance of R1 is 24 ohms? EL-0019 A. 24 ohms B. 16 ohms C. 48 ohms D. the answer can not be determined from the information given

Description : In the illustrated circuit, what is the resistance of R2 if the total current is .75 amps, the voltage is 12 VDC and the resistance of R1 is 24 ohms? EL-0019 A. 24 ohms B. 16 ohms C. 48 ohms D. the answer can not be determined from the information given

Last Answer : Answer: C

In the illustrated circuit, what is the total current if the voltage is 12 VDC, the resistance of R1 is 15 ohms, and the resistance of R2 is 10 ohms? EL-0019 A. .8 amps B. 1.5 amps C. .55 amps D. 2 amps

Description : In the illustrated circuit, what is the total current if the voltage is 12 VDC, the resistance of R1 is 15 ohms, and the resistance of R2 is 10 ohms? EL-0019 A. .8 amps B. 1.5 amps C. .55 amps D. 2 amps

Last Answer : Answer: D