How many tuned parallel LC circuits are shown in this schematic?

How many tuned parallel LC circuits are shown in this  schematic?
by

1 Answer

Answer :

Four.
by

Related questions

role of tuned LC circuit in tuned amplifier.

Description : role of tuned LC circuit in tuned amplifier.

Last Answer : In order to pick up and amplify the desired radio frequency signal, the resistive load in the audio amplifier is replaced by a tuned circuit (also called a parallel resonant circuit)as shown ... desired radio frequency signal. (ii)Amplification of the selected signal to a suitable voltage level.

The schematic diagram shown in the illustration represents which of the listed solid-state circuits? EL-0069 A. Bridge rectifier B. Magnetic amplifier C. Flip-flop generator D. Cathodic amplifier

Description : The schematic diagram shown in the illustration represents which of the listed solid-state circuits? EL-0069 A. Bridge rectifier B. Magnetic amplifier C. Flip-flop generator D. Cathodic amplifier

Last Answer : Answer: A

Can a parallel LC circuit be used as the frequency determining network for an rf amplifier?

Description : Can a parallel LC circuit be used as the frequency determining network for an rf amplifier?

Last Answer : Yes.

When is line current minimum in a parallel-LC circuit?

Description : When is line current minimum in a parallel-LC circuit?

Last Answer : At the resonant frequency.

If the fuse shown on the schematic (figure 3-10) opens, what lights will operate?

Description : If the fuse shown on the schematic (figure 3-10) opens, what lights will operate?

Last Answer : Only the brake lights.

Which of the following is true at resonance in LC circuits?

Description : Which of the following is true at resonance in LC circuits? A) The series impedance of the two elements is at a maximum and the parallel impedance is at minimum B) The series impedance of the ... D) The series impedance of the two elements is at a minimum and the parallel impedance is at maximum

Last Answer : Which of the following is true at resonance in LC circuits? A) The series impedance of the two elements is at a maximum and the parallel impedance is at minimum B) The series impedance of ... D) The series impedance of the two elements is at a minimum and the parallel impedance is at maximum

State the need of tuned amplifier in electronic circuits.

Description : State the need of tuned amplifier in electronic circuits.

Last Answer : Necessity of tuned amplifier: 1. Selection of the desired radio frequency signal. 2. Amplification of the selected signal to a selected voltage level.

What are the two main disadvantages of an LC capacitor filter?

Description : What are the two main disadvantages of an LC capacitor filter?

Last Answer : Cost and size of the inductor.

In an LC choke-input filter, what prevents the rapid charging of the capacitor?

Description : In an LC choke-input filter, what prevents the rapid charging of the capacitor?

Last Answer : The CEMF of the inductor

. What are the two main disadvantages of an LC capacitor filter?

Description : . What are the two main disadvantages of an LC capacitor filter?

Last Answer : Cost of the inductor and size of the inductor.

In an LC choke-input filter, what prevents the rapid charging of the capacitor?

Description : In an LC choke-input filter, what prevents the rapid charging of the capacitor?

Last Answer : Counter electro-motive force of the inductor.

The total power in both series and parallel circuits is computed with the formula: PT = P1 + P2 + P3 +...Pn. Why can this formula be used for both series and parallel circuits?

Description : The total power in both series and parallel circuits is computed with the formula: PT = P1 + P2 + P3 +...Pn. Why can this formula be used for both series and parallel circuits?

Last Answer : In both cases all the power used in the circuit must come from the source.

The cavities of a multicavity klystron are tuned to slightly different frequencies in what method of tuning?

Description : The cavities of a multicavity klystron are tuned to slightly different frequencies in what method of tuning?

Last Answer : Stagger tuning.

What is the reactance property at the input of a shorted quarter wavelength line? A. A parallel LC circuit B. A pure inductive reactance C. A series LC circuit D. A pure capacitive reactance

Description : What is the reactance property at the input of a shorted quarter wavelength line? A. A parallel LC circuit B. A pure inductive reactance C. A series LC circuit D. A pure capacitive reactance

Last Answer : A. A parallel LC circuit

On the synchro schematic symbol, what indicates the angular displacement of the rotor?

Description : On the synchro schematic symbol, what indicates the angular displacement of the rotor?

Last Answer : . The position of the arrow.

In reference to the schematic symbol for a diode, do electrons flow toward or away from the arrow?

Description : In reference to the schematic symbol for a diode, do electrons flow toward or away from the arrow?

Last Answer : Toward the arrow.

Why must a wiring diagram be used in conjunction with a schematic to troubleshoot a system?

Description : Why must a wiring diagram be used in conjunction with a schematic to troubleshoot a system?

Last Answer : To find the test points.

Both the VOR and the ADF in an aircraft are correctly tuned and identified. The indications from both are shown on the RMI illustrated. The information on the RMI indicates: a. That the aircraft is heading 033° (M), is on the 310° radial from the VOR, and bears 050° (M) from the NDB b. That the aircraft is heading 330° (M), is on the 310° radial from the VOR, and bears 050° (M) from the NDB c. That the aircraft is heading 330° (M), is on the 130° radial from the VOR, and bears 050° (M) from the NDB d. That the aircraft is heading 330° (M), is on the 130° radial from the VOR, and bears 230° (M) from the NDB

Description : Both the VOR and the ADF in an aircraft are correctly tuned and identified. The indications from both are shown on the RMI illustrated. The information on the RMI indicates: a. That the aircraft is heading 033° (M ... 330° (M), is on the 130° radial from the VOR, and bears 230° (M) from the NDB

Last Answer : d. That the aircraft is heading 330° (M), is on the 130° radial from the VOR, and bears 230° (M) from the NDB

Both the VOR and the ADF in an aircraft are correctly tuned and identified. The indications from both are shown on the RMI illustrated. The information on the RMI indicates: a. That the aircraft is heading 033° (M), is on the 310° radial from the VOR, and bears 050° (M) from the NDB b. That the aircraft is heading 330° (M), is on the 310° radial from the VOR, and bears 050° (M) from the NDB c. That the aircraft is heading 330° (M), is on the 130° radial from the VOR, and bears 050° (M) from the NDB d. That the aircraft is heading 330° (M), is on the 130° radial from the VOR, and bears 230° (M) from the NDB

Description : Both the VOR and the ADF in an aircraft are correctly tuned and identified. The indications from both are shown on the RMI illustrated. The information on the RMI indicates: a. That the aircraft is heading 033° (M ... 330° (M), is on the 130° radial from the VOR, and bears 230° (M) from the NDB

Last Answer : d. That the aircraft is heading 330° (M), is on the 130° radial from the VOR, and bears 230° (M) from the NDB

In the schematic of the electrical circuit shown in the illustration, what is the value of the total capacitance, when compared to the value of equal individual capacitors? EL-0038 A. Equal B. Half C. Double D. Squared

Description : In the schematic of the electrical circuit shown in the illustration, what is the value of the total capacitance, when compared to the value of equal individual capacitors? EL-0038 A. Equal B. Half C. Double D. Squared

Last Answer : Answer: C

In the schematic diagram of the DC compound generator shown in the illustration, the positive ammeter reading is 500 amps and the negative ammeter reading is 475 amps. What is the current flow through the neutral bus? EL-0037 A. 0 amp B. 12.5 amp C. 25 amp D. 975 amp

Description : In the schematic diagram of the DC compound generator shown in the illustration, the positive ammeter reading is 500 amps and the negative ammeter reading is 475 amps. What is the current flow through the neutral bus? EL-0037 A. 0 amp B. 12.5 amp C. 25 amp D. 975 amp

Last Answer : Answer: C

The electrical schematic shown in the illustration indicates the lighting feeder circuit is _____________. EL-0014 A. three phase, 450 volt, and 60 cycle B. three phase, 120 volt, and 60 cycle C. single phase, 120 volt, and 60 cycle D. not specified

Description : The electrical schematic shown in the illustration indicates the lighting feeder circuit is _____________. EL-0014 A. three phase, 450 volt, and 60 cycle B. three phase, 120 volt, and 60 cycle C. single phase, 120 volt, and 60 cycle D. not specified

Last Answer : Answer: A

The schematic diagram shown in the illustration uses symbol 'A' to represent a/an _________. EL-0011 A. non-renewable fuse link B. circuit breaker coil C. overload relay coil D. thermal overload heater

Description : The schematic diagram shown in the illustration uses symbol 'A' to represent a/an _________. EL-0011 A. non-renewable fuse link B. circuit breaker coil C. overload relay coil D. thermal overload heater

Last Answer : Answer: D

If the three-phase motor, shown in the illustrated schematic diagram, is running in the forward direction, which of the following actions must occur before the motor will reverse rotation? EL-0011 A. Normally-closed contacts '4'-'5' must open. B. Normally- open contacts '2'-'3' must close. C. 'L1' and 'L3' must be interchanged via the 'R' contacts. D. All of the above.

Description : If the three-phase motor, shown in the illustrated schematic diagram, is running in the forward direction, which of the following actions must occur before the motor will reverse rotation? EL-0011 A. Normally-closed ... 'L1' and 'L3' must be interchanged via the 'R' contacts. D. All of the above.

Last Answer : Answer: C

The electrical schematic shown in the illustration represents a/an ____________. EL-0017 A. across-the-line starter B. primary-resistor starter C. autotransformer starter D. part-winding starter

Description : The electrical schematic shown in the illustration represents a/an ____________. EL-0017 A. across-the-line starter B. primary-resistor starter C. autotransformer starter D. part-winding starter

Last Answer : Answer: A

Which component is responsible for energizing solenoid 'B1-B2' and releasing the brake for the winch motor shown in the illustration? EL-0102 A. Contactor '3M' B. A spring not shown in the schematic diagram C. Resistor 'B2-R1' D. Relay 'FR-B.O.'

Description : Which component is responsible for energizing solenoid 'B1-B2' and releasing the brake for the winch motor shown in the illustration? EL-0102 A. Contactor '3M' B. A spring not shown in the schematic diagram C. Resistor 'B2-R1' D. Relay 'FR-B.O.'

Last Answer : Answer: A

The contacts operated by the D.C. relay coil shown in the illustration are located in the schematic diagram prints at coordinates ____________. EL-0100 A. '41Y' on this page B. '52M52M' and '52H35M' C. '57R' on this page D. '52N' on page '57R'

Description : The contacts operated by the D.C. relay coil shown in the illustration are located in the schematic diagram prints at coordinates ____________. EL-0100 A. '41Y' on this page B. '52M52M' and '52H35M' C. '57R' on this page D. '52N' on page '57R'

Last Answer : Answer: C

As shown in the illustration, which of the elements listed does the line 'B' represent in the basic schematic symbol of a PNP transistor? EL-0068 A. Base B. Emitter C. Cathode D. Collector

Description : As shown in the illustration, which of the elements listed does the line 'B' represent in the basic schematic symbol of a PNP transistor? EL-0068 A. Base B. Emitter C. Cathode D. Collector

Last Answer : Answer: D

In the electrical schematic, a Zener diode will be represented by which of the symbols shown in the illustration? EL-0067 A. A B. B C. C D. D

Description : In the electrical schematic, a Zener diode will be represented by which of the symbols shown in the illustration? EL-0067 A. A B. B C. C D. D

Last Answer : Answer: A

Name a common application of counting circuits.

Description : Name a common application of counting circuits.

Last Answer : Frequency counters or frequency dividers.

What is the major factor that limits the high-frequency response of an amplifier circuits?

Description : What is the major factor that limits the high-frequency response of an amplifier circuits?

Last Answer : The capacitance of the circuit.

List the circuits that all oscilloscopes have in common.

Description : List the circuits that all oscilloscopes have in common.

Last Answer : A CRT, a group of control circuits, power supply, sweep circuitry, and deflection circuitry.

Circuits that can be interconnected without additional circuitry are known as ____________ circuits.

Description : Circuits that can be interconnected without additional circuitry are known as ____________ circuits.

Last Answer : Compatible.

Circuits which maintain constant voltage or current outputs are called dc voltage or dc current ___.

Description : Circuits which maintain constant voltage or current outputs are called dc voltage or dc current ___.

Last Answer : Regulators.

Why is the use of large value capacitors in filter circuits discouraged?

Description : Why is the use of large value capacitors in filter circuits discouraged?

Last Answer : Expense

Which of the basic timing circuits produces sharp trigger pulses directly?

Description : Which of the basic timing circuits produces sharp trigger pulses directly?

Last Answer : Blocking oscillators.

What basic circuits meet the requirements of an externally synchronized master oscillator?

Description : What basic circuits meet the requirements of an externally synchronized master oscillator?

Last Answer : Sine-wave oscillator, single-swing blocking oscillator, and master trigger (astable) multivibrator.

The actions of the tr and atr circuits depend on the impedance characteristics of what length of transmission line?

Description : The actions of the tr and atr circuits depend on the impedance characteristics of what length of transmission line?

Last Answer : Quarter-wavelength section

Which of the basic timing circuits produces sharp trigger pulses directly?

Description : Which of the basic timing circuits produces sharp trigger pulses directly?

Last Answer : Blocking oscillators.

What basic circuits meet the requirements of an externally synchronized master oscillator?

Description : What basic circuits meet the requirements of an externally synchronized master oscillator?

Last Answer : Sine-wave oscillator, single-swing blocking oscillator, and master trigger (astable) multivibrator.

What is the purpose of the majority of circuits in a radar system?

Description : What is the purpose of the majority of circuits in a radar system?

Last Answer : Timing and control.

Why is the use of large value capacitors in filter circuits discouraged?

Description : Why is the use of large value capacitors in filter circuits discouraged?

Last Answer : Expense

What do the smaller circuits in third generation computers allow for?

Description : What do the smaller circuits in third generation computers allow for?

Last Answer : Faster internal processing speeds.

What is the primary advantage of hybrid circuits?

Description : What is the primary advantage of hybrid circuits?

Last Answer : Circuit flexibility

When designing vacuum-tube circuits, what characteristics of tubes must be taken into consideration?

Description : When designing vacuum-tube circuits, what characteristics of tubes must be taken into consideration?

Last Answer : Differences in performance of tubes of the same type

Name the two series circuits that exist in a diode circuit.

Description : Name the two series circuits that exist in a diode circuit.

Last Answer : Filament and plate.

When are two circuits said to be coupled?

Description : When are two circuits said to be coupled?

Last Answer : When they are arranged so that energy from one circuit is transferred to the other circuit

Boolean algebra is used primarily by _______ to simplify circuits.

Description : Boolean algebra is used primarily by _______ to simplify circuits.

Last Answer : Design engineers.