Can a parallel LC circuit be used as the frequency determining network for an rf amplifier?

Can a parallel LC circuit be used as the frequency determining network for an rf amplifier?
by

1 Answer

Answer :

Yes.
by

Related questions

What is the purpose of a frequency-determining network in an rf amplifier?

Description : What is the purpose of a frequency-determining network in an rf amplifier?

Last Answer : To provide maximum impedance at the desired frequency.

For what class of operation is the final rf power amplifier of a plate-modulator circuit biased?

Description : For what class of operation is the final rf power amplifier of a plate-modulator circuit biased?

Last Answer : Class C

When is line current minimum in a parallel-LC circuit?

Description : When is line current minimum in a parallel-LC circuit?

Last Answer : At the resonant frequency.

What two methods are used to compensate for the problems that cause low gain in an rf amplifier?

Description : What two methods are used to compensate for the problems that cause low gain in an rf amplifier?

Last Answer : . RF transformers are used and the transistor is neutralized.

What problem is caused in an rf amplifier by a loosely coupled transformer?

Description : What problem is caused in an rf amplifier by a loosely coupled transformer?

Last Answer : A too-narrow bandpass.

What is the most common form of coupling for an rf amplifier?

Description : What is the most common form of coupling for an rf amplifier?

Last Answer : Transformer coupling.

If current gain is required from an rf amplifier, what type of component should be used as an output coupling element?

Description : If current gain is required from an rf amplifier, what type of component should be used as an output coupling element?

Last Answer : A step-down transformer.

What is the result of pulsing a pulsed rf amplifier when no rf is present?

Description : What is the result of pulsing a pulsed rf amplifier when no rf is present?

Last Answer : Oscillations at an undesired frequency.

If the rf amplifier discussed has an 80 milliwatt input, what would be the maximum output?

Description : If the rf amplifier discussed has an 80 milliwatt input, what would be the maximum output?

Last Answer : 800 watts.

role of tuned LC circuit in tuned amplifier.

Description : role of tuned LC circuit in tuned amplifier.

Last Answer : In order to pick up and amplify the desired radio frequency signal, the resistive load in the audio amplifier is replaced by a tuned circuit (also called a parallel resonant circuit)as shown ... desired radio frequency signal. (ii)Amplification of the selected signal to a suitable voltage level.

How many tuned parallel LC circuits are shown in this schematic?

Description : How many tuned parallel LC circuits are shown in this schematic?

Last Answer : Four.

When measuring a transmitter’s frequency against a suitable standard, the frequency to be measured is taken from the A. oscillator stage B. intermediate amplifier C. buffer stage D. final RF stage

Description : When measuring a transmitter’s frequency against a suitable standard, the frequency to be measured is taken from the A. oscillator stage B. intermediate amplifier C. buffer stage D. final RF stage

Last Answer : D. final RF stage

One of the following is a high powered RF ac basic transmitter that has two or more stages, the oscillator stage which determines the frequency opereation and RF amplifier stage orstages that develop the high power output. The purpose of which is to develop a good frequency stability. A. Goldsmith B. MOPA C. Alexanderson D. Hartley

Description : One of the following is a high powered RF ac basic transmitter that has two or more stages, the oscillator stage which determines the frequency opereation and RF amplifier stage orstages that develop the ... to develop a good frequency stability. A. Goldsmith B. MOPA C. Alexanderson D. Hartley

Last Answer : B. MOPA

One of the following is a possible cause of an abrupt frequency variation in a self exited transmitter oscillator circuits resulting to a poor frequency stability to hold a constant frequency oscillation. A. Heating and expansion of oscillator coil B. DC and RF ac heating of resistors which cause change in values C. Heating of capacitor in the oscillatorD. Loose connections in the oscillator, amplifier, or antenna circuits.

Description : One of the following is a possible cause of an abrupt frequency variation in a self exited transmitter oscillator circuits resulting to a poor frequency stability to hold a constant frequency ... capacitor in the oscillator D. Loose connections in the oscillator, amplifier, or antenna circuits.

Last Answer : D. Loose connections in the oscillator, amplifier, or antenna circuits.

Which of the following is one of the possible causes for a slow drift of frequency in a self exited transmitter oscillator circuits resulting to a poor frequency stability? A. Poor soldered connections B. Power supply voltage changes C. Loose connections in the oscillator, amplifier, or antenna circuits D. DC and RF heating of resistors, causing then to change values.

Description : Which of the following is one of the possible causes for a slow drift of frequency in a self exited transmitter oscillator circuits resulting to a poor frequency stability? A. Poor soldered connections ... , or antenna circuits D. DC and RF heating of resistors, causing then to change values.

Last Answer : D. DC and RF heating of resistors, causing then to change values.

How can the frequency be changed in the frequency determining network?

Description : How can the frequency be changed in the frequency determining network?

Last Answer : By changing the value.

What consists the front-end circuit of a VHF TV superheterodyne receiver? A. Mixer, RF amplifier and AFC? B. RF amplifier, Band pass filter and mixer C. Local oscillator, mixer and RF amplifier D. Local oscillator, AGC and antenna

Description : What consists the front-end circuit of a VHF TV superheterodyne receiver? A. Mixer, RF amplifier and AFC? B. RF amplifier, Band pass filter and mixer C. Local oscillator, mixer and RF amplifier D. Local oscillator, AGC and antenna

Last Answer : C. Local oscillator, mixer and RF amplifier

Refers to one of the front end circuit of a VHF TV superheterodyne receiver which is usually a separate circuit coupled to the mixer. A. Antenna feed B. AGC C. RF amplifier D. Local oscillator

Description : Refers to one of the front end circuit of a VHF TV superheterodyne receiver which is usually a separate circuit coupled to the mixer. A. Antenna feed B. AGC C. RF amplifier D. Local oscillator

Last Answer : D. Local oscillator

Which of the following methods cannot be used to increase the bandwidth for cascaded RF amplifier stages? A) Wave traps in each stage B) Stagger tuning C) A shunt damping resistor across each tuned circuit D) Doubled tuned transformers with tighter coupling

Description : Which of the following methods cannot be used to increase the bandwidth for cascaded RF amplifier stages? A) Wave traps in each stage B) Stagger tuning C) A shunt damping resistor across each tuned circuit D) Doubled tuned transformers with tighter coupling

Last Answer : A) Wave traps in each stage

What is the reactance property at the input of a shorted quarter wavelength line? A. A parallel LC circuit B. A pure inductive reactance C. A series LC circuit D. A pure capacitive reactance

Description : What is the reactance property at the input of a shorted quarter wavelength line? A. A parallel LC circuit B. A pure inductive reactance C. A series LC circuit D. A pure capacitive reactance

Last Answer : A. A parallel LC circuit

What component in an amplifier circuit tends to limit the low-frequency response of the amplifier?

Description : What component in an amplifier circuit tends to limit the low-frequency response of the amplifier?

Last Answer : The coupling capacitor (C3).

What are the two main disadvantages of an LC capacitor filter?

Description : What are the two main disadvantages of an LC capacitor filter?

Last Answer : Cost and size of the inductor.

In an LC choke-input filter, what prevents the rapid charging of the capacitor?

Description : In an LC choke-input filter, what prevents the rapid charging of the capacitor?

Last Answer : The CEMF of the inductor

. What are the two main disadvantages of an LC capacitor filter?

Description : . What are the two main disadvantages of an LC capacitor filter?

Last Answer : Cost of the inductor and size of the inductor.

In an LC choke-input filter, what prevents the rapid charging of the capacitor?

Description : In an LC choke-input filter, what prevents the rapid charging of the capacitor?

Last Answer : Counter electro-motive force of the inductor.

If one branch of a parallel network is shorted, what portion of circuit current flows through the remaining branches?

Description : If one branch of a parallel network is shorted, what portion of circuit current flows through the remaining branches?

Last Answer : None.

Calculate the noise figure of the receiver whose RF amplifier has an input resistance of 1000Ω and an equivalent shot-noise resistance of 2000Ω, a gain of 25 and load resistance of 125 kΩ. Given that the bandwidth is 1.0MHz and the temperature is 20˚C, and that the receiver is connected to an antenna with an impedance of 75Ω. A. 30.3 B. 3.03 C. 303 D. .303

Description : Calculate the noise figure of the receiver whose RF amplifier has an input resistance of 1000Ω and an equivalent shot-noise resistance of 2000Ω, a gain of 25 and load resistance of 125 kΩ. Given that the bandwidth is 1. ... to an antenna with an impedance of 75Ω. A. 30.3 B. 3.03 C. 303 D. .303

Last Answer : A. 30.3

What is the meaning of forward power? A. The power traveling from the transmitter to the antenna. B. The power radiated from the top of an antenna system. C. The power produced during the positive half of an RF cycle. D. The power used to drive a linear amplifier.

Description : What is the meaning of forward power? A. The power traveling from the transmitter to the antenna. B. The power radiated from the top of an antenna system. C. The power produced during the positive half of an RF cycle. D. The power used to drive a linear amplifier.

Last Answer : A. The power traveling from the transmitter to the antenna.

What establishes the receiver bandwidth? A. RF amplifier B. Mixer C. Local oscillator D. IF amplifier

Description : What establishes the receiver bandwidth? A. RF amplifier B. Mixer C. Local oscillator D. IF amplifier

Last Answer : D. IF amplifier

Which of the following parts of the radio receiver represent the component that extracts the desire RF signal from the electromagnetic wave? A. AF amplifier B. Antenna C. Detector D. Crystal

Description : Which of the following parts of the radio receiver represent the component that extracts the desire RF signal from the electromagnetic wave? A. AF amplifier B. Antenna C. Detector D. Crystal

Last Answer : B. Antenna

After the IF stages have been aligned, the next stage to align in FM receiver is. A. local oscillator B. limiter stage C. RF amplifier D. mixer stage

Description : After the IF stages have been aligned, the next stage to align in FM receiver is. A. local oscillator B. limiter stage C. RF amplifier D. mixer stage

Last Answer : A. local oscillator

In a Klystron amplifier, the RF voltage produces

Description : In a Klystron amplifier, the RF voltage produces  (a) amplitude modulation (b) frequency modulation (c) phase modulation (d) velocity modulation

Last Answer : In a Klystron amplifier, the RF voltage produces velocity modulation

What are the three networks used for frequency determining devices?

Description : What are the three networks used for frequency determining devices?

Last Answer : RC, LC, and crystal

What is the formula for determining total reactance in a series circuit where the values of XC and XL are known?

Description : What is the formula for determining total reactance in a series circuit where the values of XC and XL are known?

Last Answer : X = XL – XC or X = XC - XL

What components can be used to increase the high frequency response of an amplifier?

Description : What compone What components What components can be used to increase the high frequency response of an amplifier?

Last Answer : Peaking coils.

What is the major factor that limits the high-frequency response of an amplifier circuits?

Description : What is the major factor that limits the high-frequency response of an amplifier circuits?

Last Answer : The capacitance of the circuit.

What are the factors that limit the frequency response of a transistor amplifier?

Description : What are the factors that limit the frequency response of a transistor amplifier?

Last Answer : The capacitance and inductance of the circuit and the interelectrode capacitance of the transistor.

What are the upper and lower frequency limits of an amplifier?

Description : What are the upper and lower frequency limits of an amplifier?

Last Answer : The half-power points of a frequency-response curve. The upper and lower limits of the band f frequencies for which the amplifier is most effective.

What is the frequency classification of a magnetic amplifier

Description : What is the frequency classification of a magnetic amplifier

Last Answer : An audio (or low) frequency power amplifier.

In a nondegenerative parametric amplifier the difference between the input frequency and the pump frequency is called what?

Description : In a nondegenerative parametric amplifier the difference between the input frequency and the pump frequency is called what?

Last Answer : Idler- or lower-sideband frequency.

The pump signal frequency must be of what value when compared to the input signal of a simple parametric amplifier?

Description : The pump signal frequency must be of what value when compared to the input signal of a simple parametric amplifier?

Last Answer : Exactly double the input frequency.

What is the purpose of an amplifier-coupling network?

Description : What is the purpose of an amplifier-coupling network?

Last Answer : To transfer energy (a signal) from one stage to another.

The Doppler effect causes a change in what aspect of rf energy that strikes a moving object?

Description : The Doppler effect causes a change in what aspect of rf energy that strikes a moving object?

Last Answer : Frequency.

Rotation of an rf-feed source to produce a conical scan pattern is identified by what term?

Description : Rotation of an rf-feed source to produce a conical scan pattern is identified by what term?

Last Answer : Nutation.

Atmospheric interference with the travel of electromagnetic energy increases with what rf energy characteristic?

Description : Atmospheric interference with the travel of electromagnetic energy increases with what rf energy characteristic?

Last Answer : Frequency.

At what point on an open-circuited rf line do voltage peaks occur?

Description : At what point on an open-circuited rf line do voltage peaks occur?

Last Answer : At 1/2 wavelength from the end and at every 1/2 wavelength along the line

What is the most common method of testing a fixed rf attenuator?

Description : What is the most common method of testing a fixed rf attenuator?

Last Answer : Rf substitution method.

Normally, how are high-power rf tubes tested?

Description : Normally, how are high-power rf tubes tested?

Last Answer : In their circuit.

Name the three main sections of a typical rf signal generator.

Description : Name the three main sections of a typical rf signal generator.

Last Answer : Oscillator circuit, modulator, and output control circuit.

If a wave's electric lines of force rotate through 360 degrees with every cycle of rf energy, what is the polarization of this wave?

Description : If a wave's electric lines of force rotate through 360 degrees with every cycle of rf energy, what is the polarization of this wave?

Last Answer : Circular polarization.