Erosion and pits formation on the impeller of a centrifugal pump may be due to (A) Cavitation (B) Low speed of impeller (C) Its operation with delivery valve closed for considerable time after starting the pump (D) Off centering of pump with motor

Erosion and pits formation on the impeller of a centrifugal pump may
be due to
(A) Cavitation
(B) Low speed of impeller
(C) Its operation with delivery valve closed for considerable time after
starting the pump
(D) Off centering of pump with motor
by

1 Answer

Answer :

(A) Cavitation
by

Related questions

While starting a centrifugal pump, its delivery valve should be kept (A) Opened (B) Closed (C) Either opened or closed; it does not make any difference (D) Either opened or closed; depending on the fluid viscosity

Description : While starting a centrifugal pump, its delivery valve should be kept (A) Opened (B) Closed (C) Either opened or closed; it does not make any difference (D) Either opened or closed; depending on the fluid viscosity

Last Answer : (B) Closed

In centrifugal pump installation, (A) Pump is properly primed before starting (B) The diameter of the pipe at inlet as well as at outlet, is kept smaller than the delivery pipe (C) The motor may burn out if it is started with empty delivery pipe and with open gate valve (D) All the above

Description : In centrifugal pump installation,  (A) Pump is properly primed before starting  (B) The diameter of the pipe at inlet as well as at outlet, is kept smaller than the delivery pipe  (C) The ... out if it is started with empty delivery pipe and with open gate valve  (D) All the above 

Last Answer : (D) All the above 

Gear pump (A) Is a positive displacement pump (B) Is a centrifugal pump (C) Is a non-positive displacement pump (D) Can be started with delivery valve closed

Description : Gear pump (A) Is a positive displacement pump (B) Is a centrifugal pump (C) Is a non-positive displacement pump (D) Can be started with delivery valve closed

Last Answer : (A) Is a positive displacement pump

Which of the following is not the function of a volute casing provided in a centrifugal pump? (A) To reduce the head loss in discharge (B) To increase the pump efficiency (C) To collect liquid from the periphery of the impeller and to transmit it to the delivery pipe at constant velocity (D) To increase the pump discharge rate

Description : Which of the following is not the function of a volute casing provided in a centrifugal pump? (A) To reduce the head loss in discharge (B) To increase the pump efficiency (C) To collect liquid ... and to transmit it to the delivery pipe at constant velocity (D) To increase the pump discharge rate

Last Answer : Option D

In centrifugal pumps, cavitation occurs, when pressure of the impeller eye or vane becomes (A) Less than atmospheric pressure (B) More than liquid vapor pressure (C) Less than liquid vapor pressure (D) More than atmospheric pressure

Description : In centrifugal pumps, cavitation occurs, when pressure of the impeller eye or vane becomes (A) Less than atmospheric pressure (B) More than liquid vapor pressure (C) Less than liquid vapor pressure (D) More than atmospheric pressure

Last Answer : (C) Less than liquid vapor pressure

While starting an axial flow pump, its delivery valve should be kept (A) Open (B) Closed (C) Either open or closed (D) None of these

Description : While starting an axial flow pump, its delivery valve should be kept (A) Open (B) Closed (C) Either open or closed (D) None of these

Last Answer : (A) Open

In centrifugal pump operation, the cavitation can be eliminated by maintaining suction pressure __________ the vapor pressure of the liquid at the suction temperature. (A) Lower than (B) Higher than (C) Equal to (D) None of these

Description : In centrifugal pump operation, the cavitation can be eliminated by maintaining suction pressure __________ the vapor pressure of the liquid at the suction temperature. (A) Lower than (B) Higher than (C) Equal to (D) None of these

Last Answer : (B) Higher than

Pick out the wrong statement about cavitation. (A) Sudden reduction of pressure in a fluid flow system caused by flow separation, vortex formation or abrupt closing of valve leads to cavitation (B) Cavitation may be caused due to boiling of liquid by decreasing the pressure resulting in formation & collapse of vapor cavities (C) Cavitation begins at higher static pressure and lower velocity in larger diameter pipelines resulting in audible noise(D) Large scale cavitation cannot damage pipeline, restrict fluid flow anddamage steam turbine blades

Description : Pick out the wrong statement about cavitation. (A) Sudden reduction of pressure in a fluid flow system caused by flow separation, vortex formation or abrupt closing of valve leads to cavitation ... (D) Large scale cavitation cannot damage pipeline, restrict fluid flow and damage steam turbine blades

Last Answer : (D) Large scale cavitation cannot damage pipeline, restrict fluid flow and damage steam turbine blades

What causes cavitation in centrifugal pump? (A) High suction pressure (B) Low barometric pressure(C) Low suction pressure(D) High suction velocity

Description : What causes cavitation in centrifugal pump? (A) High suction pressure (B) Low barometric pressure (C) Low suction pressure (D) High suction velocity

Last Answer : (C) Low suction pressure

Cavitation in a centrifugal pump can be avoided by keeping the (A) Inlet pressure high (B) Outlet pressure low (C) Inlet pressure low (D) Outlet pressure high

Description : Cavitation in a centrifugal pump can be avoided by keeping the (A) Inlet pressure high (B) Outlet pressure low (C) Inlet pressure low (D) Outlet pressure high

Last Answer : (A) Inlet pressure high

With a constant diameter impeller of a centrifugal pump (A) Its capacity varies directly as the square of speed (B) Head varies as the square of speed (C) Horsepower input varies as the square of speed (D) Head varies as the speed

Description : With a constant diameter impeller of a centrifugal pump (A) Its capacity varies directly as the square of speed (B) Head varies as the square of speed (C) Horsepower input varies as the square of speed (D) Head varies as the speed

Last Answer : (B) Head varies as the square of speed

Head developed by a centrifugal pump depends on its (A) Speed (B) Impeller diameter (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : Head developed by a centrifugal pump depends on its (A) Speed (B) Impeller diameter (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : C) Both (A) and (B)

At a constant speed of the centrifugal pump, it’s __________ the impeller diameter. (A) Capacity varies directly with (B) Head varies as the square of (C) Horsepower varies as the cube of (D) All (A), (B) and (C)

Description : At a constant speed of the centrifugal pump, it’s __________ the impeller diameter. (A) Capacity varies directly with (B) Head varies as the square of (C) Horsepower varies as the cube of (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Consider a centrifugal pump having a specific impeller diameter, fixed impeller speed pumping a liquid of constant density at a particular discharge capacity. With decrease in the capacity of the pump, the __________ decreases. (A) NPSH required (B) BHP required by the pump (C) Head of the liquid pumped (D) All (A), (B) and (C)

Description : Consider a centrifugal pump having a specific impeller diameter, fixed impeller speed pumping a liquid of constant density at a particular discharge capacity. With decrease in the capacity of the pump, the __________ decreases. (A) ... the pump (C) Head of the liquid pumped (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Which of the following options will facilitate the achievement of a very high head (say 30 metres) in case of a centrifugal pump? (A) Increasing the impeller speed and the volute area (B) Increasing the number of vanes in the impeller (C) Mounting of two or more impellers in series on a single shaft (D) Either of (A), (B) or (C)

Description : Which of the following options will facilitate the achievement of a very high head (say 30 metres) in case of a centrifugal pump? (A) Increasing the impeller speed and the volute area (B) Increasing the number of vanes ... or more impellers in series on a single shaft (D) Either of (A), (B) or (C)

Last Answer : (C) Mounting of two or more impellers in series on a single shaft

Theoretical head developed by a centrifugal pump does not depend upon the __________ the impeller. (A) Radius of (B) Speed of (C) Fluid velocity leaving (D) None of these

Description : Theoretical head developed by a centrifugal pump does not depend upon the __________ the impeller. (A) Radius of (B) Speed of (C) Fluid velocity leaving (D) None of these

Last Answer : (D) None of these

Which is the correct relationship for a centrifugal pump? (Where, D = Impeller diameter, inches H = Head developed, ft of liquid pumped N = Speed of pump, rpm) (A) D = 1840 H0.5 /N (B) D = 1840 N/H0.5 (C) H = 1840 D0.5 /N (D) D = 1840 H/N

Description : Which is the correct relationship for a centrifugal pump? (Where, D = Impeller diameter, inches H = Head developed, ft of liquid pumped N = Speed of pump, rpm) (A) D = 1840 H0.5 /N (B) D = 1840 N/H0.5 (C) H = 1840 D0.5 /N (D) D = 1840 H/N

Last Answer : (A) D = 1840 H0.5 /N

The head developed by a centrifugal pump is largely determined by the (A) Power of the pump(B) Nature of the liquid being pumped(C) Angle of the vanes and the speed of the tip of the impeller(D) Vapour pressure of the liquid

Description : The head developed by a centrifugal pump is largely determined by the (A) Power of the pump (B) Nature of the liquid being pumped (C) Angle of the vanes and the speed of the tip of the impeller (D) Vapour pressure of the liquid

Last Answer : (C) Angle of the vanes and the speed of the tip of the impeller

In case of a centrifugal pump, the theoretical head developed is dependent on the __________ the impeller. (A) Speed of (B) Diameter of (C) Fluid velocity leaving (D) All (A), (B) and (C)

Description : In case of a centrifugal pump, the theoretical head developed is dependent on the __________ the impeller. (A) Speed of (B) Diameter of (C) Fluid velocity leaving (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

The capacity of a centrifugal pump Can be increased by increasing the (A) Impeller diameter or speed (B) Number of pumps and joining them in series (C) Number of pumps and joining them in parallel (D) All (A), (B) and (C)

Description : The capacity of a centrifugal pump Can be increased by increasing the (A) Impeller diameter or speed (B) Number of pumps and joining them in series (C) Number of pumps and joining them in parallel (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Pick up the correct statement from the following: (A) At a particular speed of operation, the head produced decreases with the increase of discharge (B) At zero discharge, discharge valve remaining closed, the head developed is maximum which is known as shut-off head (C) At a particular speed the discharge at which efficiency of a pump is maximum, is known as normal discharge (D) All the above

Description : Pick up the correct statement from the following: (A) At a particular speed of operation, the head produced decreases with the increase of discharge (B) At zero discharge, discharge valve remaining closed ... which efficiency of a pump is maximum, is known as normal discharge (D) All the above

Last Answer : (D) All the above

Reciprocating pumps compared to centrifugal pumps (A) Deliver liquid at uniform pressure (B) Can handle slurries more efficiently (C) Are not subject to air binding (D) Can be operated with delivery valve closed

Description : Reciprocating pumps compared to centrifugal pumps (A) Deliver liquid at uniform pressure (B) Can handle slurries more efficiently (C) Are not subject to air binding (D) Can be operated with delivery valve closed

Last Answer : (C) Are not subject to air binding

Cavitation occurs in a centrifugal pump when the suction pressure is (A) Less than the vapour pressure of the liquid at that temperature (B) Greater than the vapour pressure of the liquid at that temperature (C) Equal to the vapour pressure (D) Equal to the developed head

Description : Cavitation occurs in a centrifugal pump when the suction pressure is (A) Less than the vapour pressure of the liquid at that temperature (B) Greater than the vapour pressure of the liquid at that temperature (C) Equal to the vapour pressure (D) Equal to the developed head

Last Answer : (A) Less than the vapour pressure of the liquid at that temperature

Good design of the casing of a centrifugal pump aims at minimising the (A) Cavitation (B) Frictional losses (C) Kinetic energy loss (D) Static head

Description : Good design of the casing of a centrifugal pump aims at minimising the (A) Cavitation (B) Frictional losses (C) Kinetic energy loss (D) Static head

Last Answer : Option C

A single-phase induction motor will only start if you spin the rotor rapidly with the line switch closed. After starting, its speed fluctuates between very slow and half-speed. The problem probably lies in the ________. A. starting winding B. centrifugal mechanism C. centrifugal switch D. running winding

Description : A single-phase induction motor will only start if you spin the rotor rapidly with the line switch closed. After starting, its speed fluctuates between very slow and half-speed. The problem ... in the ________. A. starting winding B. centrifugal mechanism C. centrifugal switch D. running winding

Last Answer : Answer: D

Check valve provided in the discharge line of a centrifugal pump serves the purpose of controlling the (A) Back flow of fluid in the event of stoppage of pump (B) Discharge pressure (C) Flow of liquid during operation of the pump (D) All (A), (B) and (C)

Description : Check valve provided in the discharge line of a centrifugal pump serves the purpose of controlling the (A) Back flow of fluid in the event of stoppage of pump (B) Discharge pressure (C) Flow of liquid during operation of the pump (D) All (A), (B) and (C)

Last Answer : (A) Back flow of fluid in the event of stoppage of pump

A centrifugal pump loses prime after starting. The reason of this trouble may be (A) Incomplete priming (B) Too high a suction lift (C) Low available NPSH and air leaks in the suction pipe (D) All (A), (B), and (C)

Description : A centrifugal pump loses prime after starting. The reason of this trouble may be (A) Incomplete priming (B) Too high a suction lift (C) Low available NPSH and air leaks in the suction pipe (D) All (A), (B), and (C)

Last Answer : (D) All (A), (B), and (C)

Draining of shallow pits or sump is done by a sump pump, which is a __________ pump. (A) Single stage vertical (B) Centrifugal (C) Plunger (D) Diffuser

Description : Draining of shallow pits or sump is done by a sump pump, which is a __________ pump. (A) Single stage vertical (B) Centrifugal (C) Plunger (D) Diffuser

Last Answer : (A) Single stage vertical

Priming of a centrifugal pump is done to (A) Increase the mass flow rate of fluid (B) Develop effective pressure rise by the pump (C) Avoid chances of separation inside the impeller (D) None of these

Description : Priming of a centrifugal pump is done to (A) Increase the mass flow rate of fluid (B) Develop effective pressure rise by the pump (C) Avoid chances of separation inside the impeller (D) None of these

Last Answer : (C) Avoid chances of separation inside the impeller

Centrifugal pump is normally classified on the basis of the (A) rpm (B) Type of casing (C) Impeller blade angle (D) Number of blades in impeller

Description : Centrifugal pump is normally classified on the basis of the (A) rpm (B) Type of casing (C) Impeller blade angle (D) Number of blades in impeller

Last Answer : (B) Type of casing

In case of a centrifugal pump, the ratio of total delivered pressure to pressure developed with the impeller is called the __________ efficiency. (A) Manometric (B) Mechanical (C) Volumetric (D) Overall

Description : In case of a centrifugal pump, the ratio of total delivered pressure to pressure developed with the impeller is called the __________ efficiency. (A) Manometric (B) Mechanical (C) Volumetric (D) Overall

Last Answer : (A) Manometric

A centrifugal pump is called a turbine pump, if it is having a (A) Turbine type impeller (B) Vaned diffusion casing (C) Rotating vaned volute (D) None of these

Description : A centrifugal pump is called a turbine pump, if it is having a (A) Turbine type impeller (B) Vaned diffusion casing (C) Rotating vaned volute (D) None of these

Last Answer : (B) Vaned diffusion casing

A mixed flow centrifugal pump (A) Employs such an impeller, through which the flow is a combination of radial & axial flow (B) Mixes the two fluids before pumping them (C) Pumps the two fluids separately and then mixes them (D) Employs impellers in both the radial & axial directions

Description : A mixed flow centrifugal pump (A) Employs such an impeller, through which the flow is a combination of radial & axial flow (B) Mixes the two fluids before pumping them (C) Pumps the two fluids separately and then mixes them (D) Employs impellers in both the radial & axial directions

Last Answer : (A) Employs such an impeller, through which the flow is a combination of radial & axial flow

Design of the casing of centrifugal pump should be such as to minimise the (A) Back flow through impeller (B) Loss of kinetic head (C) Loss of static head (D) None of these

Description : Design of the casing of centrifugal pump should be such as to minimise the (A) Back flow through impeller (B) Loss of kinetic head (C) Loss of static head (D) None of these

Last Answer : (B) Loss of kinetic head

In case of a, centrifugal pump, the ratio h1/h2is termed as the __________ efficiency (where, h1 = actual measured head & h2 = head imparted to the fluid by impeller). (A) Mechanical (B) Overall (C) Volumetric (D) Impeller

Description : In case of a, centrifugal pump, the ratio h1/h2is termed as the __________ efficiency (where, h1 = actual measured head & h2 = head imparted to the fluid by impeller). (A) Mechanical (B) Overall (C) Volumetric (D) Impeller

Last Answer : A) Mechanical

A single-phase induction motor fails to start. The rotor is spun rapidly with the line switch closed. Having started by this method it is noted that the motor fluctuates between a very slow speed and half speed. The problem probably lies in the ______ A. starting winding B. centrifugal mechanism C. centrifugal switch D. running winding

Description : A single-phase induction motor fails to start. The rotor is spun rapidly with the line switch closed. Having started by this method it is noted that the motor fluctuates between a very slow ... lies in the ______ A. starting winding B. centrifugal mechanism C. centrifugal switch D. running winding

Last Answer : Answer: D

Pick up the correct statement from the following regarding radial flow centrifugal pumps: (A) These are provided with volute type or turbine type casings (B) In involute type of radial flow centrifugal pump, the impeller discharges into a gradually expanding spiral casing (C) The efficiency of turbine type of radial flow centrifugal pump, is always higher than that of volute type (D) All the above

Description : Pick up the correct statement from the following regarding radial flow centrifugal pumps:  (A) These are provided with volute type or turbine type casings  (B) In involute type of radial flow ... centrifugal pump, is always higher than that of  volute type  (D) All the above 

Last Answer : (D) All the above 

If the centrifugal switch or relay used for cutting out the starting winding of a split-phase induction motor fails to open once the motor is in operation, the _____________. A. motor will overspeed B. starting winding will burn out C. motor will immediately stall under load D. motor torque will be above normal at rated speed

Description : If the centrifugal switch or relay used for cutting out the starting winding of a split-phase induction motor fails to open once the motor is in operation, the _____________. A. motor will overspeed B ... C. motor will immediately stall under load D. motor torque will be above normal at rated speed

Last Answer : Answer: B

Centrifugal pumps as compared to reciprocating pumps (A) Run at a lower speed for the same discharge (B) Do not need priming (C) Deliver fluid with pulsating/fluctuating discharge (D) Can be run with discharge line valve closed for a short interval

Description : Centrifugal pumps as compared to reciprocating pumps (A) Run at a lower speed for the same discharge (B) Do not need priming (C) Deliver fluid with pulsating/fluctuating discharge (D) Can be run with discharge line valve closed for a short interval

Last Answer : (D) Can be run with discharge line valve closed for a short interval

Check in a centrifugal pump is (A) Provided in the discharge line (B) Generally a globe valve (C) Provided to prevent liquid from backing up through the pump when the pump is turned off or accidently stops running (D) All (A), (B) and (C)

Description : Check in a centrifugal pump is (A) Provided in the discharge line (B) Generally a globe valve (C) Provided to prevent liquid from backing up through the pump when the pump is turned off or accidently stops running (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Specific speed of a centrifugal pump depends upon the __________ head. (A) Suction (B) Delivery (C) Manometric (D) None of these

Description : Specific speed of a centrifugal pump depends upon the __________ head. (A) Suction (B) Delivery (C) Manometric (D) None of these

Last Answer : (D) None of these

If a single-phase induction motor fails to start, the problem may be _____________. A. an open in the main winding B. a shorted shunt field C. a closed centrifugal switch D. low circuit frequency

Description : If a single-phase induction motor fails to start, the problem may be _____________. A. an open in the main winding B. a shorted shunt field C. a closed centrifugal switch D. low circuit frequency

Last Answer : Answer: A

If a single-phase induction motor fails to start, the problem may be _____________. A. an open in the run winding B. a shorted shunt field C. a closed centrifugal switch D. low circuit frequency

Description : If a single-phase induction motor fails to start, the problem may be _____________. A. an open in the run winding B. a shorted shunt field C. a closed centrifugal switch D. low circuit frequency

Last Answer : Answer: A

The vent valve provided in a liquid handling centrifugal pump is (A) Generally a needle valve (B) Used to release any gases that might be vapour locking the pump (C) Helpful in easy removal of samples (D) All (A), (B) and (C)

Description : The vent valve provided in a liquid handling centrifugal pump is (A) Generally a needle valve (B) Used to release any gases that might be vapour locking the pump (C) Helpful in easy removal of samples (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Which one of the following statements is correct? A. Reciprocating compressors are used to supply large quantities of air at a lower pressure ratio B. Centrifugal compressors are used to supply large quantities of air at a lower pressure ratio C. Centrifugal compressors are used to supply small quantities of air at a lower pressure ratio D. Centrifugal compressors cannot be run at high speed because of impeller, diffuser and casing.

Description : Which one of the following statements is correct? A. Reciprocating compressors are used to supply large quantities of air at a lower pressure ratio B. Centrifugal compressors are used to supply ... . Centrifugal compressors cannot be run at high speed because of impeller, diffuser and casing.

Last Answer : ANSWER : B

The most important factor, which determines the maximum height to which water can be lifted by a pump at standard temperature is the (A) Barometric pressure (B) Speed of the impeller (C) Diameter of the impeller (D) Both (B) and (C)

Description : The most important factor, which determines the maximum height to which water can be lifted by a pump at standard temperature is the (A) Barometric pressure (B) Speed of the impeller (C) Diameter of the impeller (D) Both (B) and (C)

Last Answer : (A) Barometric pressure

Liquid delivery by centrifugal pump starts, only when the head developed by it is equal to the __________ head. (A) Manometric (B) Total (C) Static (D) Friction

Description : Liquid delivery by centrifugal pump starts, only when the head developed by it is equal to the __________ head. (A) Manometric (B) Total (C) Static (D) Friction

Last Answer : (A) Manometric

Probability of cavitation occuring becomes very high, when the local __________ resulting in water bubbles formation, which on rupture cause cavitation (A) Pressure falls below the vapour pressure (B) Pressure becomes very high (C) Temperature becomes low (D) All 'a', 'b' & 'c'

Description : Probability of cavitation occuring becomes very high, when the local __________ resulting in water bubbles formation, which on rupture cause cavitation (A) Pressure falls below the vapour pressure (B) Pressure becomes very high (C) Temperature becomes low (D) All 'a', 'b' & 'c'

Last Answer : (D) All 'a', 'b' & 'c'

Low specific speed of a pump implies that, it is a/an __________ pump. (A) Axial flow (B) Centrifugal (C) Mixed flow (D) None of these

Description : Low specific speed of a pump implies that, it is a/an __________ pump. (A) Axial flow (B) Centrifugal (C) Mixed flow (D) None of these

Last Answer : (B) Centrifugal