Low specific speed of a pump implies that, it is a/an __________ pump. (A) Axial flow (B) Centrifugal (C) Mixed flow (D) None of these

Low specific speed of a pump implies that, it is a/an __________ pump.
(A) Axial flow
(B) Centrifugal
(C) Mixed flow
(D) None of these
by

1 Answer

Answer :

(B) Centrifugal
by

Related questions

High specific speed of a pump implies that, it is a/an __________ pump. (A) Centrifugal (B) Mixed flow (C) Axial flow (D) None of these

Description : High specific speed of a pump implies that, it is a/an __________ pump. (A) Centrifugal (B) Mixed flow (C) Axial flow (D) None of these

Last Answer : (C) Axial flow

Higher specific speed (200-500) of a centrifugal pump indicates that the pump is of __________ flow type. (A) Axial (B) Radial (C) Mixed (D) None of these

Description : Higher specific speed (200-500) of a centrifugal pump indicates that the pump is of __________ flow type. (A) Axial (B) Radial (C) Mixed (D) None of these

Last Answer : (A) Axial

A mixed flow centrifugal pump (A) Employs such an impeller, through which the flow is a combination of radial & axial flow (B) Mixes the two fluids before pumping them (C) Pumps the two fluids separately and then mixes them (D) Employs impellers in both the radial & axial directions

Description : A mixed flow centrifugal pump (A) Employs such an impeller, through which the flow is a combination of radial & axial flow (B) Mixes the two fluids before pumping them (C) Pumps the two fluids separately and then mixes them (D) Employs impellers in both the radial & axial directions

Last Answer : (A) Employs such an impeller, through which the flow is a combination of radial & axial flow

Which of the following is most prone to pulsating discharge flow? (A) Centrifugal pump(B) Reciprocating pump(C) Gear pump(D) Axial flow pump

Description : Which of the following is most prone to pulsating discharge flow? (A) Centrifugal pump (B) Reciprocating pump (C) Gear pump (D) Axial flow pump

Last Answer : (C) Gear pump

Most commonly used pump for lifting water in water supply mains, is (A) Axial flow pump (B) Reciprocating pump (C) Rotary type pump (D) Centrifugal pumps

Description : Most commonly used pump for lifting water in water supply mains, is  (A) Axial flow pump  (B) Reciprocating pump  (C) Rotary type pump  (D) Centrifugal pumps 

Last Answer : (A) Axial flow pump 

Specific speed of a centrifugal pump depends upon the __________ head. (A) Suction (B) Delivery (C) Manometric (D) None of these

Description : Specific speed of a centrifugal pump depends upon the __________ head. (A) Suction (B) Delivery (C) Manometric (D) None of these

Last Answer : (D) None of these

Consider a centrifugal pump having a specific impeller diameter, fixed impeller speed pumping a liquid of constant density at a particular discharge capacity. With decrease in the capacity of the pump, the __________ decreases. (A) NPSH required (B) BHP required by the pump (C) Head of the liquid pumped (D) All (A), (B) and (C)

Description : Consider a centrifugal pump having a specific impeller diameter, fixed impeller speed pumping a liquid of constant density at a particular discharge capacity. With decrease in the capacity of the pump, the __________ decreases. (A) ... the pump (C) Head of the liquid pumped (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

A centrifugal pump has the following specifications: Power = 4 H.P.; Speed = 800 rpm Head = 8 metres Flow = 1000 litres/minutes. If its speed is halved, the power consumed now will be __________ hp. (A) 0.5 (B) 2 (C) 4 (D) 1

Description : A centrifugal pump has the following specifications: Power = 4 H.P.; Speed = 800 rpm Head = 8 metres Flow = 1000 litres/minutes. If its speed is halved, the power consumed now will be __________ hp. (A) 0.5 (B) 2 (C) 4 (D) 1

Last Answer : (A) 0.5

A centrifugal pump has the following specifications: Power = 4 H.P.; Speed = 800 rpm Head = 8 metres Flow = 1000 litres/minutes. If its speed is halved, then the new head will be __________ metres. (A) 2 (B) 4 (C) 8 (D) 5.5

Description : A centrifugal pump has the following specifications: Power = 4 H.P.; Speed = 800 rpm Head = 8 metres Flow = 1000 litres/minutes. If its speed is halved, then the new head will be __________ metres. (A) 2 (B) 4 (C) 8 (D) 5.5

Last Answer : (A) 2

A centrifugal pump has the following specifications: Power = 4 H.P.; Speed = 800 rpm Head = 8 metres Flow = 1000 litres/minutes. If its speed is halved, the new discharge will be __________ litres/minute. (A) 500 (B) 200 (C) 1000 (D) 750

Description : A centrifugal pump has the following specifications: Power = 4 H.P.; Speed = 800 rpm Head = 8 metres Flow = 1000 litres/minutes. If its speed is halved, the new discharge will be __________ litres/minute. (A) 500 (B) 200 (C) 1000 (D) 750

Last Answer : (A) 500

The specific speed of a centrifugal compressor is generally A. less than that of reciprocating compressor B. independent of compressor type, but depends only on size of compressor C. higher than that of axial compressor D. more than specific speed of reciprocating compressor but less than axial compressor

Description : The specific speed of a centrifugal compressor is generally A. less than that of reciprocating compressor B. independent of compressor type, but depends only on size of compressor C. higher ... axial compressor D. more than specific speed of reciprocating compressor but less than axial compressor

Last Answer : ANSWER : C

Specific speed of a centrifugal pump relates it with another pump having the (A) Dynamic similarity (B) Same efficiency (C) Same speed (D) Geometrical similaritySpecific speed of a centrifugal pump relates it with another pump having the (A) Dynamic similarity (B) Same efficiency (C) Same speed (D) Geometrical similaritySpecific speed of a centrifugal pump relates it with another pumphaving the(A) Dynamic similarity(B) Same efficiency(C) Same speed(D) Geometrical similarity

Description : Specific speed of a centrifugal pump relates it with another pump having the (A) Dynamic similarity (B) Same efficiency (C) Same speed (D) Geometrical similaritySpecific speed of a centrifugal ... another pumphaving the(A) Dynamic similarity(B) Same efficiency(C) Same speed(D) Geometrical similarity

Last Answer : (A) Dynamic similarity

In case of unsteady fluid flow, conditions & flow pattern change with the passage of time at a position in a flow situation. Which of the following is an example of unsteady flow? (A) Discharge of water by a centrifugal pump being run at a constant rpm (B) Water flow in the suction and discharge pipe of a reciprocating pump (C) Water discharge from a vertical vessel in which constant level is maintained (D) Low velocity flow of a highly viscous liquid through a hydraulically smooth pipe

Description : In case of unsteady fluid flow, conditions & flow pattern change with the passage of time at a position in a flow situation. Which of the following is an example of unsteady flow? (A) ... level is maintained (D) Low velocity flow of a highly viscous liquid through a hydraulically smooth pipe

Last Answer : (B) Water flow in the suction and discharge pipe of a reciprocating pump

In case of a __________ the energy of flow is considerably decreased downstream of the machine. (A) Blower (B) Turbine (C) Centrifugal pump (D) Centrifugal fan

Description : In case of a __________ the energy of flow is considerably decreased downstream of the machine. (A) Blower (B) Turbine (C) Centrifugal pump (D) Centrifugal fan

Last Answer : (B) Turbine

Which of the following can be used to create a flow of gas, where no significant compression is required? (A) Reciprocating compressor (B) Blower (C) Axial flow compressor (D) Centrifugal compressor

Description : Which of the following can be used to create a flow of gas, where no significant compression is required? (A) Reciprocating compressor (B) Blower (C) Axial flow compressor (D) Centrifugal compressor

Last Answer : (B) Blower

Erosion and pits formation on the impeller of a centrifugal pump may be due to (A) Cavitation (B) Low speed of impeller (C) Its operation with delivery valve closed for considerable time after starting the pump (D) Off centering of pump with motor

Description : Erosion and pits formation on the impeller of a centrifugal pump may be due to (A) Cavitation (B) Low speed of impeller (C) Its operation with delivery valve closed for considerable time after starting the pump (D) Off centering of pump with motor

Last Answer : (A) Cavitation

Theoretical head developed by a centrifugal pump does not depend upon the __________ the impeller. (A) Radius of (B) Speed of (C) Fluid velocity leaving (D) None of these

Description : Theoretical head developed by a centrifugal pump does not depend upon the __________ the impeller. (A) Radius of (B) Speed of (C) Fluid velocity leaving (D) None of these

Last Answer : (D) None of these

At a constant speed of the centrifugal pump, it’s __________ the impeller diameter. (A) Capacity varies directly with (B) Head varies as the square of (C) Horsepower varies as the cube of (D) All (A), (B) and (C)

Description : At a constant speed of the centrifugal pump, it’s __________ the impeller diameter. (A) Capacity varies directly with (B) Head varies as the square of (C) Horsepower varies as the cube of (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

In case of a centrifugal pump, the theoretical head developed is dependent on the __________ the impeller. (A) Speed of (B) Diameter of (C) Fluid velocity leaving (D) All (A), (B) and (C)

Description : In case of a centrifugal pump, the theoretical head developed is dependent on the __________ the impeller. (A) Speed of (B) Diameter of (C) Fluid velocity leaving (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Why the work per kg of air flow in axial flow compressor is less compared to centrifugal compressor for same pressure ratio ?

Description : Why the work per kg of air flow in axial flow compressor is less compared to centrifugal compressor for same pressure ratio ?

Last Answer : Isentropic efficiency of axial flow compressor is higher.

Differentiate between : (i) Reciprocating and rotary air compressor (ii) Centrifugal and axial flow compressor

Description : Differentiate between : (i) Reciprocating and rotary air compressor (ii) Centrifugal and axial flow compressor

Last Answer : (i) Reciprocating and rotary air compressor: Sr. No. Reciprocating air compressor  Rotary air compressor  1 It is having to and fro motion. It is having rotary ... I.C. engine and for refrigerants and industrial gases. Used universally with large gas turbine. 

While starting an axial flow pump, its delivery valve should be kept (A) Open (B) Closed (C) Either open or closed (D) None of these

Description : While starting an axial flow pump, its delivery valve should be kept (A) Open (B) Closed (C) Either open or closed (D) None of these

Last Answer : (A) Open

Working of a __________ pump characterises mixed flow. (A) Turbine (B) Piston (C) Diaphragm (D) None of these

Description : Working of a __________ pump characterises mixed flow. (A) Turbine (B) Piston (C) Diaphragm (D) None of these

Last Answer : (A) Turbine

Paddle agitator (A) Is suitable for mixing low viscosity liquids (B) Produces axial flow (C) Moves at very high speed (D) None of these

Description : Paddle agitator (A) Is suitable for mixing low viscosity liquids (B) Produces axial flow (C) Moves at very high speed (D) None of these

Last Answer : (A) Is suitable for mixing low viscosity liquids

Propellers are (A) Axial flow mixers (B) Low speed impeller (C) Used for mixing liquids of high viscosity (D) Radial flow mixers

Description : Propellers are (A) Axial flow mixers (B) Low speed impeller (C) Used for mixing liquids of high viscosity (D) Radial flow mixers

Last Answer : (A) Axial flow mixers

Priming of a centrifugal pump is done to (A) Increase the mass flow rate of fluid (B) Develop effective pressure rise by the pump (C) Avoid chances of separation inside the impeller (D) None of these

Description : Priming of a centrifugal pump is done to (A) Increase the mass flow rate of fluid (B) Develop effective pressure rise by the pump (C) Avoid chances of separation inside the impeller (D) None of these

Last Answer : (C) Avoid chances of separation inside the impeller

With increasing flow rate, the hydraulic efficiency of a centrifugal pump (A) Monotonically decreases (B) Decreases and then increases(C) Remains constant(D) Increases and then decreases

Description : With increasing flow rate, the hydraulic efficiency of a centrifugal pump (A) Monotonically decreases (B) Decreases and then increases (C) Remains constant (D) Increases and then decreases

Last Answer : (A) Monotonically decreases

Check valve provided in the discharge line of a centrifugal pump serves the purpose of controlling the (A) Back flow of fluid in the event of stoppage of pump (B) Discharge pressure (C) Flow of liquid during operation of the pump (D) All (A), (B) and (C)

Description : Check valve provided in the discharge line of a centrifugal pump serves the purpose of controlling the (A) Back flow of fluid in the event of stoppage of pump (B) Discharge pressure (C) Flow of liquid during operation of the pump (D) All (A), (B) and (C)

Last Answer : (A) Back flow of fluid in the event of stoppage of pump

Design of the casing of centrifugal pump should be such as to minimise the (A) Back flow through impeller (B) Loss of kinetic head (C) Loss of static head (D) None of these

Description : Design of the casing of centrifugal pump should be such as to minimise the (A) Back flow through impeller (B) Loss of kinetic head (C) Loss of static head (D) None of these

Last Answer : (B) Loss of kinetic head

With a constant diameter impeller of a centrifugal pump (A) Its capacity varies directly as the square of speed (B) Head varies as the square of speed (C) Horsepower input varies as the square of speed (D) Head varies as the speed

Description : With a constant diameter impeller of a centrifugal pump (A) Its capacity varies directly as the square of speed (B) Head varies as the square of speed (C) Horsepower input varies as the square of speed (D) Head varies as the speed

Last Answer : (B) Head varies as the square of speed

Which of the following options will facilitate the achievement of a very high head (say 30 metres) in case of a centrifugal pump? (A) Increasing the impeller speed and the volute area (B) Increasing the number of vanes in the impeller (C) Mounting of two or more impellers in series on a single shaft (D) Either of (A), (B) or (C)

Description : Which of the following options will facilitate the achievement of a very high head (say 30 metres) in case of a centrifugal pump? (A) Increasing the impeller speed and the volute area (B) Increasing the number of vanes ... or more impellers in series on a single shaft (D) Either of (A), (B) or (C)

Last Answer : (C) Mounting of two or more impellers in series on a single shaft

Head developed by a centrifugal pump depends on its (A) Speed (B) Impeller diameter (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : Head developed by a centrifugal pump depends on its (A) Speed (B) Impeller diameter (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : C) Both (A) and (B)

Which is the correct relationship for a centrifugal pump? (Where, D = Impeller diameter, inches H = Head developed, ft of liquid pumped N = Speed of pump, rpm) (A) D = 1840 H0.5 /N (B) D = 1840 N/H0.5 (C) H = 1840 D0.5 /N (D) D = 1840 H/N

Description : Which is the correct relationship for a centrifugal pump? (Where, D = Impeller diameter, inches H = Head developed, ft of liquid pumped N = Speed of pump, rpm) (A) D = 1840 H0.5 /N (B) D = 1840 N/H0.5 (C) H = 1840 D0.5 /N (D) D = 1840 H/N

Last Answer : (A) D = 1840 H0.5 /N

The head developed by a centrifugal pump is largely determined by the (A) Power of the pump(B) Nature of the liquid being pumped(C) Angle of the vanes and the speed of the tip of the impeller(D) Vapour pressure of the liquid

Description : The head developed by a centrifugal pump is largely determined by the (A) Power of the pump (B) Nature of the liquid being pumped (C) Angle of the vanes and the speed of the tip of the impeller (D) Vapour pressure of the liquid

Last Answer : (C) Angle of the vanes and the speed of the tip of the impeller

The capacity of a centrifugal pump Can be increased by increasing the (A) Impeller diameter or speed (B) Number of pumps and joining them in series (C) Number of pumps and joining them in parallel (D) All (A), (B) and (C)

Description : The capacity of a centrifugal pump Can be increased by increasing the (A) Impeller diameter or speed (B) Number of pumps and joining them in series (C) Number of pumps and joining them in parallel (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

The maximum depth from which a centrifugal pump can draw water is (A) Dependent on the speed of the pump (B) Dependent on the power of the pump (C) 34 feet (D) 150 feet

Description : The maximum depth from which a centrifugal pump can draw water is (A) Dependent on the speed of the pump (B) Dependent on the power of the pump (C) 34 feet (D) 150 feet

Last Answer : (C) 34 feet

What causes cavitation in centrifugal pump? (A) High suction pressure (B) Low barometric pressure(C) Low suction pressure(D) High suction velocity

Description : What causes cavitation in centrifugal pump? (A) High suction pressure (B) Low barometric pressure (C) Low suction pressure (D) High suction velocity

Last Answer : (C) Low suction pressure

A centrifugal pump loses prime after starting. The reason of this trouble may be (A) Incomplete priming (B) Too high a suction lift (C) Low available NPSH and air leaks in the suction pipe (D) All (A), (B), and (C)

Description : A centrifugal pump loses prime after starting. The reason of this trouble may be (A) Incomplete priming (B) Too high a suction lift (C) Low available NPSH and air leaks in the suction pipe (D) All (A), (B), and (C)

Last Answer : (D) All (A), (B), and (C)

Reciprocating pumps are not able to compete with the centrifugal pump for industrial use, mainly because these pumps have (A) Very low speeds (B) Smaller discharge (C) Higher capital &maintenance cost (D) High vibrations

Description : Reciprocating pumps are not able to compete with the centrifugal pump for industrial use, mainly because these pumps have (A) Very low speeds (B) Smaller discharge (C) Higher capital &maintenance cost (D) High vibrations

Last Answer : (C) Higher capital &maintenance cost

Cavitation in a centrifugal pump can be avoided by keeping the (A) Inlet pressure high (B) Outlet pressure low (C) Inlet pressure low (D) Outlet pressure high

Description : Cavitation in a centrifugal pump can be avoided by keeping the (A) Inlet pressure high (B) Outlet pressure low (C) Inlet pressure low (D) Outlet pressure high

Last Answer : (A) Inlet pressure high

Crude oil is pumped by a __________ pump. (A) Gear (B) Centrifugal

Description : Crude oil is pumped by a __________ pump. (A) Gear (B) Centrifugal

Last Answer : (B) Centrifugal

The type of pump used for the recirculation of molten sodium coolant in liquid metal cooled reactor is a/an __________ pump. (A) Electromagnetic (B) Reciprocating (C) Centrifugal (D) Volute

Description : The type of pump used for the recirculation of molten sodium coolant in liquid metal cooled reactor is a/an __________ pump. (A) Electromagnetic (B) Reciprocating (C) Centrifugal (D) Volute

Last Answer : (A) Electromagnetic

For pumping slurry, one can use a __________ pump. (A) Reciprocating (B) Diaphragm (C) Centrifugal (D) Pneumatic

Description : For pumping slurry, one can use a __________ pump. (A) Reciprocating (B) Diaphragm (C) Centrifugal (D) Pneumatic

Last Answer : (B) Diaphragm

For the production of very high vacuum, a __________ pump is normally used. (A) Diffusion (B) Centrifugal (C) Jet ejector (D) Piston

Description : For the production of very high vacuum, a __________ pump is normally used. (A) Diffusion (B) Centrifugal (C) Jet ejector (D) Piston

Last Answer : (A) Diffusion

Liquid delivery by centrifugal pump starts, only when the head developed by it is equal to the __________ head. (A) Manometric (B) Total (C) Static (D) Friction

Description : Liquid delivery by centrifugal pump starts, only when the head developed by it is equal to the __________ head. (A) Manometric (B) Total (C) Static (D) Friction

Last Answer : (A) Manometric

Boiler feed water pump is usually a __________ pump.(A) Reciprocating (B) Gear (C) Multistage centrifugal (D) Diaphragm

Description : Boiler feed water pump is usually a __________ pump. (A) Reciprocating (B) Gear (C) Multistage centrifugal (D) Diaphragm

Last Answer : (C) Multistage centrifugal

Draining of shallow pits or sump is done by a sump pump, which is a __________ pump. (A) Single stage vertical (B) Centrifugal (C) Plunger (D) Diffuser

Description : Draining of shallow pits or sump is done by a sump pump, which is a __________ pump. (A) Single stage vertical (B) Centrifugal (C) Plunger (D) Diffuser

Last Answer : (A) Single stage vertical

Maintenance cost of a __________ pump for a particular duty is the least. (A) Centrifugal (B) Reciprocating (C) Volute (D) Gear

Description : Maintenance cost of a __________ pump for a particular duty is the least. (A) Centrifugal (B) Reciprocating (C) Volute (D) Gear

Last Answer : (A) Centrifugal

A mono pump is a __________ pump. (A) Centrifugal (B) Piston (C) Positive acting rotary (D) A group of vacuum

Description : A mono pump is a __________ pump. (A) Centrifugal (B) Piston (C) Positive acting rotary (D) A group of vacuum

Last Answer : (C) Positive acting rotary