Description : From the following, which one is a type of vibration measuring instrument?(A) Mechanical (B) Electrical (C) Magnetic (D) All of the above
Last Answer : (D) All of the above
Description : Vibration measuring instruments are classified on the basis of ____________. (A) contact between the vibrating system and measuring instrument (B) the requirement of power source (C) method of measurements (D) all of the above
Last Answer : (D) all of the above
Description : The instruments which are used to measure the ___________ of a vibrating body are called vibration measuring instrument. (A) displacement (B) velocity (C) acceleration (D) all of the above
Description : Which type of frequency measuring instrument has multiple reeds of different natural frequency to measure vibrations? A. Fullarton tachometer B. Frahm Tachometer C. Both A. and B. D. None of the above
Last Answer : B. Frahm Tachometer
Description : Which of the following is a type of free vibration? A Longitudinal vibrations B Transverse vibrations C Torsional vibrations D A, B and C
Last Answer : D A, B and C
Description : In the diagram shown below, if rotor X and rotor Z rotate in same direction and rotor Y rotates in opposite direction, then specify the type of node vibration. A. Three node vibration B. Two node vibration C. Single node vibration D. None of the above
Last Answer : B. Two node vibration
Description : Which of the following is a type of free vibration? A. Longitudinal vibrations B. Transverse vibrations C. Torsional vibrations D. A, B and C
Last Answer : D. A, B and C
Description : In which type of vibrations, amplitude of vibration goes on decreasing every cycle? A) Damped vibrations B) Undamped vibrations C) Both a. and b. D) None of the above
Last Answer : A) Damped vibrations
Description : Which of the following is a type of free vibration? ( A ) Longitudinal vibrations ( C ) Torsional vibrations D ( B ) Transverse vibrations ( D ) A, B and C
Last Answer : ( D ) A, B and C
Description : In which type of vibrations, amplitude of vibration goes on decreasing every cycle? a. Damped vibrations b. Undamped vibrations c. Both a. and b. d. None of the above
Last Answer : a. Damped vibrations
Description : In which type of vibrations, amplitude of vibration goes on decreasing every cycle? a. Dampedvibrations b. Undampedvibrations c. Botha.andb. d. None of the above
Last Answer : c. Botha.andb.
Description : In damped vibrations, the amplitude of the resulting vibration gradually reduces. This is due to the reason that an amount of energy is always dissipated to overcome the ________ * 1 point (A) Frictional resistance (B) Work done(C) Fluid pressure (D) Air pressure
Last Answer : (A) Frictional resistance
Description : The vibration in a vehicle is normally expressed in the terms of the ______________. (A) displacement (B) velocity (C) acceleration (D) none of the above
Last Answer : (C) acceleration
Description : In a two-rotor system, torsional vibration occurs only if the rotors are moving in the ______ direction. (A) same (B) opposite (C) either same or opposite (D) none of the above
Last Answer : (B) opposite
Description : The accelerometers are commonly used in vibration measurement due to their ___________. (A) small size and low sensitivity (B) the large size and high sensitivity (C) the large size and low sensitivity (D) small size and high sensitivity
Last Answer : (D) small size and high sensitivity
Description : Which of the following systems produce a vibration in the foundation? (A) Coupled machine(B) Uncoupled machine (C) Balanced machine (D) Unbalanced machine
Last Answer : (D) Unbalanced machine
Description : In vibration isolation system, if ω/ωn, then the phase difference between the transmitted force and the disturbing force is A 0° B 90° C 180° D 270°
Last Answer : C 180°
Description : The accelerometer is used as a transducer to measure earthquake in Richter scale. Its design is based on the principle that A Its natural frequency is very low in comparison to the frequency ... is equal to the frequency of vibration D Measurement of vibratory motion is without any reference point
Last Answer : C Its natural frequency is equal to the frequency of vibration
Description : In vibration isolation system, if ω/ωn < 2, then for all values of damping factor, the transmissibility will be A less than unity B equal to unity C greater than unity D zero
Last Answer : C greater than unity
Description : The ratio of the maximum displacement of the forced vibration to the deflection due to the static force, is known as A Damping factor B Damping coefficient C Logarithmic decrement D Magnification factor
Last Answer : D Magnification factor
Description : When there is a reduction in amplitude over every cycle of vibration, then the body is said to have A Free vibration B Forced vibration C Damped vibration D None of the mentioned
Last Answer : C Damped vibration
Description : Calculate natural frequency of damped vibration, if damping factor is 0.52 and natural frequency of the system is 30 rad/sec which consists of machine supported on springs and dashpots. A 25.62 rad/sec B 20.78 rad/sec C 14.4 rad/sec D 15.33 rad/sec
Last Answer : A 25.62 rad/sec
Description : The number of cycles described in one second is known as _______. A period of vibration B cycle C frequency D all of the above
Last Answer : C frequency
Description : The motion completed during one time period is known as _______. A period of vibration B cycle C frequency D all of the above
Last Answer : B cycle
Description : In a two-rotor system, torsional vibration occurs only if the rotors are moving in the ______ direction. A. same B. opposite C. either same or opposite D. none of the above
Last Answer : B. opposite
Description : The motion of a system executing harmonic motion with one natural frequency is known as _______ A. principal mode of vibration B. natural mode of vibration C. both a. and b. D. none of the above
Last Answer : C. both a. and b.
Description : What is meant by node point? A. The point at which amplitude of vibration is maximum B. The point at which amplitude of vibration is minimum C. The point at which amplitude of vibration is zero D. None of the above
Last Answer : C. The point at which amplitude of vibration is zero
Description : In a dynamic vibration absorber system, under tuned conditions which of the following relation holds good? A K 1 K 2 =M 1 M 2 B K 1 M 2 =M 1 K 2 C K 1 M 1 = K 2 M 2 D none of the mentioned
Last Answer : B K 1 M 2 =M 1 K 2
Description : Dynamic vibration absorber is suitable for A varying speed machines B constant speed machines C Zero speed range machines D None of the mentioned
Last Answer : B constant speed machines
Description : Calculate natural frequency of damped vibration, if damping factor is 0.52 and natural frequency of the system is 30 rad/sec which consists of machine supported on springs and dashpots. A 21 rad/sec B 25.62 rad/sec C 20.22 Hz D 3.15 Hz
Last Answer : B 25.62 rad/sec
Description : During resonance A the Vibrations remains unaffected B no vibration occurs C low amplitude of vibration occurs D high amplitude of vibration occurs
Last Answer : D high amplitude of vibration occurs
Description : The ratio of the maximum displacement of the forced vibration to the deflection due to the static force is known as A Logarithmic decrement B Magnification factor C Damping factor D None of the mentioned
Last Answer : B Magnification factor
Description : In coulomb damping the frequency of damped vibrations is A Equal to that of undamped vibrations B Less than that of undamped vibrationsC More than that of undamped vibrations D Independent of the frequency of undamped vibration
Last Answer : A Equal to that of undamped vibrations
Description : Natural frequency of the system is due to A Resonance B Forced Vibration C Damping D Free Vibration
Last Answer : D Free Vibration
Description : Increasing which of the following factor would result in increase of free torsional vibration? A. Radius of gyration B. Mass moment of inertia C. Polar moment of inertia D. Length
Last Answer : C. Polar moment of inertia
Description : In vibration isolation system, if ω/ω n > 1, then the phase difference between the transmitted force and the disturbing force is A. 0° B. 90° C. 180° D. 270°
Last Answer : C. 180°
Description : In vibration isolation system, the transmissibility will be equal to unity, for all values of damping factor, if ω/ωn is A. Equal to 1 B. Equal to √2 C. Less than √2 D. Greater than √2
Last Answer : B. Equal to √2
Description : An increase in the mass moment of inertia results in ________ in vibration frequency. A. increase B. decrease C. unchanged D. none of the above
Last Answer : B. decrease
Description : The motion completed during one time period is known as _______. A. period of vibration B. cycle C. frequency D. all of the above
Last Answer : B. cycle
Description : . The motion completed during one time period is known as _______. A. period of vibration B. cycle C. frequency D. all of the above
Description : The motion of a system executing harmonic motion with one natural frequency is known as _______ A) principal mode of vibration B) natural mode of vibration C) both a. and b. D)none of the above
Last Answer : C) both a. and b.
Description : The two resonant frequency ratio (ω/ ω2) in a dynamic vibration absorber system for a mass ratio 0.2 are given by A) 0 ; 1.0 B) 0.801 ; 1.248 C) 0.458 ; 1.124 D) 0.642 ; 1.558
Last Answer : B) 0.801 ; 1.248
Description : Critical speed of shaft and disc system A) Is equal to natural frequency of the system in transverse vibration B) Is equal to natural frequency of the system in torsional vibration C) Is ... of the system in longitudinal vibration D) Bears no relationship to any of the system natural frequency
Last Answer : A) Is equal to natural frequency of the system in transverse vibration
Description : Centrifugal absorber is used to reduce A) Centrifugal force in rotating system B) Torsional vibration of rotating system C) Vibration in linear system D) Transverse vibrations
Last Answer : B) Torsional vibration of rotating system
Description : Which of the following condition should be satisfied in the design of a vibration absorber ? A) Natural frequency of the auxiliary system should be equal to the natural frequency of the main ... D) Natural frequency of the auxiliary system should be twice natural frequency of the main system
Last Answer : A) Natural frequency of the auxiliary system should be equal to the natural frequency of the main system
Description : The rotating shaft or rotor vibrates with excessive lateral vibration at angular speed at which occurs is called as A) rotating speed B) critical speed C) vibrating speed D) None of the above
Last Answer : B) critical speed
Description : The principal of mode vibration can be given by A) Two masses vibrate at Different frequency and in same phase B) Two masses vibrate at Different frequency and in Different phase C) Two masses vibrate at same frequency and in Different phase D) Two masses vibrate at same frequency and in same phase
Last Answer : D) Two masses vibrate at same frequency and in same phase
Description : Dynamic vibration absorber is suitable for A) Constant speed machine B) Varying speed machine C) zero speed machine D) None of the above
Last Answer : A) Constant speed machine
Description : where springs of low damping are required for the purpose of vibration isolation, it will be most desirable to use A) Metallic springs B) Rubber pad C) Air springs D) Neoprene pads
Last Answer : A) Metallic springs