What is purpose of freewheeling diode and DC filter circuit in the charger?

What is purpose of freewheeling diode and DC filter circuit in the charger?
by

1 Answer

Answer :

Freewheeling diode is used to protect the semiconductor components used in the charger from the back emf, which is induced in the inductive coils of relays when the supply to the relays is cut off. The magnetic field in the relays collapses and induces high voltage in reverse direction. This emf is shunted by the freewheeling diode, which is connected in reverse bios with the output.

DC filter is used to smoothen the output, which has ripple. Ripple frequency is same as system frequency for half wave rectifier and 2 times of system frequency for full wave rectifier. The filter, which is a capacitor, will oppose any change in voltage. Thus the ripple will not be allowed to come to zero.  
by

Related questions

Write the function of freewheeling diode.

Description : Write the function of freewheeling diode.

Last Answer : Function of Freewheeling Diode (FWD): a) Freewheeling diode is used across inductive loads such as coils, dc motor armature etc. to prevent voltage spikes across these loads when the switching ... current is shifted from switching device, it is turned off easily and regain its blocking ability.

A freewheeling diode in a phase controlled converter

Description : A freewheeling diode in a phase controlled converter  A) Deceases the possibility of discontinuous conduction in the load B) Increases the possibility of discontinuous conduction in the load C) Reduces the power factor and causes over voltages D) Causes over voltages

Last Answer : A freewheeling diode in a phase controlled converter Deceases the possibility of discontinuous conduction in the load 

A freewheeling diode in phase -controlled rectifiers

Description : A freewheeling diode in phase -controlled rectifiers  (a) enables inverter operation (b) is responsible for additional reactive power (c) improves the line power factor (d) is responsible for additional harmonics

Last Answer : A freewheeling diode in phase -controlled rectifiers improves the line power factor

In the illustration, the diode between terminals 16 and 17 is to _________. EL-0046 A. act as a short circuit for the sensing coil when CEMF is applied B. insure that the voltage across the coil does not exceed 9 volts C. improve response time D. act as a filter to prevent hunting

Description : In the illustration, the diode between terminals 16 and 17 is to _________. EL-0046 A. act as a short circuit for the sensing coil when CEMF is applied B. insure that the voltage across the coil does not exceed 9 volts C. improve response time D. act as a filter to prevent hunting

Last Answer : Answer: A

What are the advantages of freewheeling diodes in a controlled in a controlled rectifier?

Description : What are the advantages of freewheeling diodes in a controlled in a controlled rectifier?

Last Answer : a. Input power factor is improved. b. Load current waveform is improved and thus the load performance is better.

What is the function of freewheeling diodes in controlled rectifier?

Description : What is the function of freewheeling diodes in controlled rectifier?

Last Answer : It serves two process. a. It prevents the output voltage from becoming negative. b. The load current is transferred from the main thyristors to the freewheeling diode, thereby allowing all of its thyristors to regain their blocking states.

What are the parts of a 48V DC charger?

Description : What are the parts of a 48V DC charger?

Last Answer : Main transformer: This steps down the 3Φ 415V supply to the require value of voltage. Synchronizing transformer for phase sequence: This gives the synchronizing signal to the firing card. That is, ... Power supply card: This gives power supply for the controller card, firing card and protection. 

In the illustration, the diode between terminals 16 and 17 is to _________. EL-0046 A. insure that the voltage across the governor coil (EG-3P) never exceeds .6 VDC B. compensate for the temperature difference of the governor oil heating up C. protect the electronic governor from counter EMF D. act as a filter to prevent hunting

Description : In the illustration, the diode between terminals 16 and 17 is to _________. EL-0046 A. insure that the voltage across the governor coil (EG-3P) never exceeds .6 VDC B. compensate for the ... heating up C. protect the electronic governor from counter EMF D. act as a filter to prevent hunting

Last Answer : Answer: C

The purpose of the bias winding in figure 'B' shown in the illustration is for ____________. EL-0091 A. changing the direction of current in the control winding B. setting the operating point of the device C. allowing the use of either AC or DC in the load circuit D. changing the direction of current through the load

Description : The purpose of the bias winding in figure 'B' shown in the illustration is for ____________. EL-0091 A. changing the direction of current in the control winding B. setting the operating point of the ... use of either AC or DC in the load circuit D. changing the direction of current through the load

Last Answer : Answer: B

The purpose of DC generator brushes is to _____________. A. neutralize armature reaction B. conduct electric current to an outside circuit C. convert DC current to AC current D. provide excitation to a DC generator

Description : The purpose of DC generator brushes is to _____________. A. neutralize armature reaction B. conduct electric current to an outside circuit C. convert DC current to AC current D. provide excitation to a DC generator

Last Answer : Answer: B

In the illustration, the component VR2 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to terminal 1 that controls the input to terminal 10 C. a zener diode that regulates the voltage to terminal 2 at 9.1 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Description : In the illustration, the component VR2 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to terminal ... 2 at 9.1 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Last Answer : Answer: C

In the illustration, the component VR1 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to terminal 9 that controls the input to terminal 10 C. a zener diode that regulates the voltage to terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Description : In the illustration, the component VR1 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to ... terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Last Answer : Answer: A

In the illustration, the component VR1 on the A1A1 PCB is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply B. a variable resistor diode to control the output to terminal 9 that controls the input to terminal 10 C. a zener diode that regulates the voltage to terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Description : In the illustration, the component VR1 on the A1A1 PCB is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply B. a variable resistor diode to control the output to terminal 9 that controls ... terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Last Answer : Answer: C

Which of the following statements represents an application of a silicon controlled rectifier? A. To provide DC power for a main propulsion motor. B. For use as a voltage reference diode. C. For sensing flame in an automated burner. D. To eliminate power supply hum.

Description : Which of the following statements represents an application of a silicon controlled rectifier? A. To provide DC power for a main propulsion motor. B. For use as a voltage reference diode. C. For sensing flame in an automated burner. D. To eliminate power supply hum.

Last Answer : Answer: A

Which of the following circuit elements is used to 'block' DC in an electronic circuit? (1) Resistances (2) Capacitance (3) Inductance (4) Diode

Description : Which of the following circuit elements is used to 'block' DC in an electronic circuit? (1) Resistances (2) Capacitance (3) Inductance (4) Diode

Last Answer : (2) Capacitance Explanation: A capacitor (originally known as condenser) is a passive two-terminal electrical component used to store energy in an electric field. Capacitors are widely used ... electric power transmission systems for stabilizing voltage and power flow, and for many other purposes.

Which of the following circuit elements is used to ‘block’ DC in an electronic circuit ? (1) Resistances (2) Capacitance (3) Inductance (4) Diode

Description : Which of the following circuit elements is used to ‘block’ DC in an electronic circuit ? (1) Resistances (2) Capacitance (3) Inductance (4) Diode

Last Answer : Capacitance

The illustrated device is a _______. EL-0064 A. full wave bridge rectifier B. half wave bridge rectifier C. solid state voltage regulator D. direct current (DC) filter

Description : The illustrated device is a _______. EL-0064 A. full wave bridge rectifier B. half wave bridge rectifier C. solid state voltage regulator D. direct current (DC) filter

Last Answer : Answer: A

What is the purpose of DIODE across the interposing coils in PLC?

Description : What is the purpose of DIODE across the interposing coils in PLC?

Last Answer : To dissipate the stored energy in magnetic field of the interposing coils (Free wheeling action). If it is not provided the stored energy will affect the PLC card circuit.

In a logic circuit the NOR and NAND gate functions ____________. A. must be accomplished with a common base transistor arrangement B. are available in diode form C. are exact opposites with the same NOR and NAND inputs D. have output conditions that are exact opposites to the output condition for OR and AND, respectively

Description : In a logic circuit the NOR and NAND gate functions ____________. A. must be accomplished with a common base transistor arrangement B. are available in diode form C. are exact opposites with the ... . have output conditions that are exact opposites to the output condition for OR and AND, respectively

Last Answer : Answer: D

Electric circuits are protected against overloads and short circuits by means of a/an ______________. A. circuit breaker B. amplifier C. diode D. capacitor

Description : Electric circuits are protected against overloads and short circuits by means of a/an ______________. A. circuit breaker B. amplifier C. diode D. capacitor

Last Answer : Answer: A

The illustrated circuit is a _____________. EL-0024 A. megohm meter B. Gauss meter C. wheatstone bridge D. germanium diode tester

Description : The illustrated circuit is a _____________. EL-0024 A. megohm meter B. Gauss meter C. wheatstone bridge D. germanium diode tester

Last Answer : Answer: C

Electrical circuits are protected against overheating by means of a/an ______________. A. circuit breaker B. amplifier C. diode D. capacitor

Description : Electrical circuits are protected against overheating by means of a/an ______________. A. circuit breaker B. amplifier C. diode D. capacitor

Last Answer : Answer: A

What are the advantages of free wheeling diode in rectifier circuit?

Description : What are the advantages of free wheeling diode in rectifier circuit?

Last Answer : The input power factor is improved. It prevents the output voltage from becoming negative. Load current waveform is improved.

Section II of the circuit shown in the illustration is the ____________. EL-0085 A. voltage regulator B. filter C. rectifier D. voltage transformer

Description : Section II of the circuit shown in the illustration is the ____________. EL-0085 A. voltage regulator B. filter C. rectifier D. voltage transformer

Last Answer : Answer: C

Section IV of the circuit shown in the illustration is the _____________. EL-0085 A. voltage regulator B. filter C. rectifier D. voltage transformer

Description : Section IV of the circuit shown in the illustration is the _____________. EL-0085 A. voltage regulator B. filter C. rectifier D. voltage transformer

Last Answer : Answer: A

Section III of the circuit shown in the illustration is a _____________. EL-0085 A. voltage regulator B. filter C. rectifier D. voltage transformer

Description : Section III of the circuit shown in the illustration is a _____________. EL-0085 A. voltage regulator B. filter C. rectifier D. voltage transformer

Last Answer : Answer: B

The device shown in the illustration is being used ________. EL-0083 A. in a step-down operation B. in a step-up operation C. in an isolation circuit D. as a filter

Description : The device shown in the illustration is being used ________. EL-0083 A. in a step-down operation B. in a step-up operation C. in an isolation circuit D. as a filter

Last Answer : Answer: A

Why and where the magnetic filter is provided in stator water circuit?

Description : Why and where the magnetic filter is provided in stator water circuit?

Last Answer : Magnetic filter is provided to catch the metal particles in stator water circuit, which are produced in the pipelines. This is mounted at the end of the circuit nearer to the inlet of the generator. 

which components act as the filter network in the diode detector?

Description : which components act as the filter network in the diode detector?

Last Answer : C1 and R1.

What is the purpose of using a charger under your dinner plates?

Description : What is the purpose of using a charger under your dinner plates?

Last Answer : A charger plate placed beneath the dinner plate adds elegance to the table setting and also helps catch food which may spill from the dinner plate.

What was the primary purpose of Brands developing Charger plates?

Description : What was the primary purpose of Brands developing Charger plates?

Last Answer : Charger plates are usually used as a decorative feature for parties, weddings and other special events.

The purpose of the commutator and brushes on a DC generator is to _____________. A. transfer generated direct current voltage from the armature to the line B. convert the alternating voltage generated within the armature to a direct voltage C. provide a sliding contact method to excite the field D. reduce sparking between the armature and the carbon brushes

Description : The purpose of the commutator and brushes on a DC generator is to _____________. A. transfer generated direct current voltage from the armature to the line B. convert the alternating voltage ... contact method to excite the field D. reduce sparking between the armature and the carbon brushes

Last Answer : Answer: B

The purpose of a cage rotor winding placed on the rotor of a synchronous motor is to _____________. A. provide excitation to the DC field B. start the machine as an induction motor C. contribute extra torque at synchronous speed D. prevent the machine from falling out of step

Description : The purpose of a cage rotor winding placed on the rotor of a synchronous motor is to _____________. A. provide excitation to the DC field B. start the machine as an induction motor C. contribute extra torque at synchronous speed D. prevent the machine from falling out of step

Last Answer : Answer: B

What is the purpose of DC winding resistance test?

Description : What is the purpose of DC winding resistance test?

Last Answer : To detect the shorting of winding and loose or poor connection of the windings. 

In accordance with Coast Guard Regulations (46 CFR), each battery operated relay-controlled lantern must _____________. A. be readily portable B. contain a dry cell battery having a minimum capacity of 10 amp hours C. have an automatic battery charger to maintain the battery in a fully charged state D. all of the above

Description : In accordance with Coast Guard Regulations (46 CFR), each battery operated relay-controlled lantern must _____________. A. be readily portable B. contain a dry cell battery having a minimum capacity of ... automatic battery charger to maintain the battery in a fully charged state D. all of the above

Last Answer : Answer: C

In the illustration, the chemical reaction depicted indicates that the _________. EL-0061 A. battery is being charged at a high rate B. cell is short circuited C. cell is discharging D. battery is attached to a trickle charger

Description : In the illustration, the chemical reaction depicted indicates that the _________. EL-0061 A. battery is being charged at a high rate B. cell is short circuited C. cell is discharging D. battery is attached to a trickle charger

Last Answer : Answer: C

Loss of or weak residual magnetism in an alternator or generator can be corrected for by _________________. A. running the rotor in the opposite direction for 5 minutes B. allowing the generator to run at 10% of normal speed for 5 minutes C. running the generator at normal speed with the field rheostat fully counterclockwise D. using a storage battery or battery charger to 'flash' the field

Description : Loss of or weak residual magnetism in an alternator or generator can be corrected for by _________________. A. running the rotor in the opposite direction for 5 minutes B. allowing the generator ... rheostat fully counterclockwise D. using a storage battery or battery charger to 'flash' the field

Last Answer : Answer: D

A lead-acid battery is considered fully charged when the ______________. A. electrolyte gasses freely B. battery charger ammeter indicates a positive reading C. terminal voltage reaches a constant value at a given temperature D. specific gravity of all cells reaches the correct value and no longer increases over a period of 1 to 4 hours

Description : A lead-acid battery is considered fully charged when the ______________. A. electrolyte gasses freely B. battery charger ammeter indicates a positive reading C. terminal voltage reaches a constant value at a ... cells reaches the correct value and no longer increases over a period of 1 to 4 hours

Last Answer : Answer: D

What are the protections provided in charger?

Description : What are the protections provided in charger?  

Last Answer : 1. Over load (49). 2. Over voltage (59). 3. Short-circuit (3250 Amps). 4. Phase sequence and phase fail. 5. di/dt and dv/dt protection. 

What is the rating of switchyard battery charger and batteries?

Description : What is the rating of switchyard battery charger and batteries? 

Last Answer : Switchyard is having Float cum boost charger of 282 V DC maximum and 100 Amps rated charger of six-pulse full wave thyristerised controlled rectifier. Batteries are tubular 220 V DC. +ve plate is made ... minutes. Specific gravity 1110 5 and specific gravity after 10 hrs discharge is 1150 5. 

What are the functions of charger?

Description : What are the functions of charger? 

Last Answer : 1. For initial charging. 2. For float charging. 3. For battery equalizing charging. 4. For battery boost charging. 5. To supply normal DC loads. 

What you mean by Drooping characteristics of charger?

Description : What you mean by Drooping characteristics of charger?

Last Answer : When the charger is connected to excess load of charger rating the charger should able to supply the load with out over loaded by maintaining the terminal voltage within limit without over load trip. This called a drooping output voltage characteristics. 

Explain the operation of 48 V battery charger.

Description : Explain the operation of 48 V battery charger. 

Last Answer : The supply for the charger is from MCC. The supply is tapped for power supply to control card, PF correction capacitor. LC filter is used for suppressing surge voltage. The main supply is ... works on principle of magnetic amplifier. There is also provision for smooth rising of output voltage. 

Draw the circuit diagram of battery charger using SCR and explain it’s working.

Description : Draw the circuit diagram of battery charger using SCR and explain it’s working.

Last Answer : Battery charger circuit using SCR: The figure shows the battery charger circuit using SCR. A 12V discharged battery is connected in the circuit and switch SW is closed. The singlephase 230V ... not fired. In this way, after full charging, further charging is automatically stopped.

A series wound DC motor has its armature and field connected in series with a resistor. When the motor is disconnected from its power supply, this motor will exemplify __________. A. the proper connections for across the line starting B. the proper connections for an automatic strip heater C. a reversing controller circuit D. dynamic braking

Description : A series wound DC motor has its armature and field connected in series with a resistor. When the motor is disconnected from its power supply, this motor will exemplify __________. A. the ... the proper connections for an automatic strip heater C. a reversing controller circuit D. dynamic braking

Last Answer : Answer: D

Which of the listed conditions might contribute to very rapid wearing of a DC machine's commutator bars? A. A grounded commutator bar B. Using improper carbon brushes C. Aligning the front and rear mica V-rings improperly D. An open circuit in the armature

Description : Which of the listed conditions might contribute to very rapid wearing of a DC machine's commutator bars? A. A grounded commutator bar B. Using improper carbon brushes C. Aligning the front and rear mica V-rings improperly D. An open circuit in the armature

Last Answer : Answer: B

A short circuit in the armature of a DC motor will cause the motor to _____________. A. run fast B. hum when energized C. spark at the brushes D. fail to start

Description : A short circuit in the armature of a DC motor will cause the motor to _____________. A. run fast B. hum when energized C. spark at the brushes D. fail to start

Last Answer : Answer: C

When an AC or a DC motor fails to start, the FIRST step in troubleshooting should be to check the ____________. A. motor windings for obvious opens B. motor controller leads for continuity C. fuse or circuit breaker D. motor controller leads for grounds

Description : When an AC or a DC motor fails to start, the FIRST step in troubleshooting should be to check the ____________. A. motor windings for obvious opens B. motor controller leads for continuity C. fuse or circuit breaker D. motor controller leads for grounds

Last Answer : Answer: C

To limit the current flow through a DC voltmeter to as low a value as possible, the moving coil circuit is provided with a/an _____________. A. high series resistance B. high parallel resistance C. series inductor D. external shunt

Description : To limit the current flow through a DC voltmeter to as low a value as possible, the moving coil circuit is provided with a/an _____________. A. high series resistance B. high parallel resistance C. series inductor D. external shunt

Last Answer : Answer: A