Where preloaded ball bearings used?

Where preloaded ball bearings used? 
by

1 Answer

Answer :

If more vibration exists even when machine is not in running conditions.  
by

Related questions

The failure of ball bearings used in electric motors can result from _____________. A. failure to clean the bearing before repacking B. failure to maintain proper alignment C. excess lubrication forcing the bearing full of grease and eliminating all areas of expansion D. all of the above

Description : The failure of ball bearings used in electric motors can result from _____________. A. failure to clean the bearing before repacking B. failure to maintain proper alignment C. excess lubrication forcing the bearing full of grease and eliminating all areas of expansion D. all of the above

Last Answer : Answer: D

When removing ball or roller bearings from the shaft of a motor, you should use a _____________. A. rawhide hammer B. brass mallet C. wheel puller D. soft iron pry bar

Description : When removing ball or roller bearings from the shaft of a motor, you should use a _____________. A. rawhide hammer B. brass mallet C. wheel puller D. soft iron pry bar

Last Answer : Answer: C

The only point in the steering stand shown in the illustration which needs periodic lubrication is the ______________. EL-0098 A. repeater assembly ball bearings B. steering wheel bearing C. operation selector switch D. course selector pointer

Description : The only point in the steering stand shown in the illustration which needs periodic lubrication is the ______________. EL-0098 A. repeater assembly ball bearings B. steering wheel bearing C. operation selector switch D. course selector pointer

Last Answer : Answer: B

I am getting a Gateway PC with vista preloaded, any ideas where the best forums for advice, bug fixes and tweeks are?

Description : I am getting a Gateway PC with vista preloaded, any ideas where the best forums for advice, bug fixes and tweeks are?

Last Answer : 2.6ghz and 2gb RAM sounds fine for vista. If everything was properly installed, you shouldn’t have any problems. Lifehacker.com is a great resource for bug fixes, tweaks and hacks. Most of it will just improve your experience, nothing is really necessary.

Are the new iMacs preloaded with OSS leopard?

Description : Are the new iMacs preloaded with OSS leopard?

Last Answer : No.

Which of the following statements are true about eccentrically loaded circular base? a) All bolts are symmetrically spaced with equal angle on either side of vertical b) Bolts are not preloaded c) Bearing is rigid d) Dowel pins are used to relieve stresses

Description : Which of the following statements are true about eccentrically loaded circular base? a) All bolts are symmetrically spaced with equal angle on either side of vertical b) Bolts are not preloaded c) Bearing is rigid d) Dowel pins are used to relieve stresses

Last Answer : a) All bolts are symmetrically spaced with equal angle on either side of vertical

How do I rejuvinate ball bearings?

Description : How do I rejuvinate ball bearings?

Last Answer : If they are ceramic, forget it. They are toast. If they are steel you can soak them in kerosene to get rid of the bits and old grease and then repack with new grease . If you don’t have kerosene you can spray with carb cleaner. (The link I included is for cars but it is still true for longboards.)

Ball bearings are used in cycles, scooters etc to -Physics

Description : Ball bearings are used in cycles, scooters etc to -Physics

Last Answer : Reduce the friction between the wheel and the axle.

Ball bearings are used in cycles, scooters etc. to _____. A. Reduce the friction between the wheel and the axle B. Increase the friction between the wheel and the axle C. Reduce the friction between ground and the wheel D. None of these

Description : Ball bearings are used in cycles, scooters etc. to _____. A. Reduce the friction between the wheel and the axle B. Increase the friction between the wheel and the axle C. Reduce the friction between ground and the wheel D. None of these

Last Answer : ANSWER: A

The function of ball bearings in a wheel is – (1) to increase friction (2) to convert kinetic friction into rolling friction (3) to convert static friction into kinetic friction (4) just for convenience

Description : The function of ball bearings in a wheel is – (1) to increase friction (2) to convert kinetic friction into rolling friction (3) to convert static friction into kinetic friction (4) just for convenience

Last Answer : (2) to convert kinetic friction into rolling friction Explanation: A ball bearing is a type of rollingelement bearing that uses balls to maintain the separation between the bearing races. The purpose of a ball bearing is to reduce rotational friction and support radial and axial loads.

Ball bearings are generally made of (A) Plain carbon steel (B) Chrome carbon steel (C) Stainless steel (D) Malleable cast iron

Description : Ball bearings are generally made of (A) Plain carbon steel (B) Chrome carbon steel (C) Stainless steel (D) Malleable cast iron

Last Answer : (B) Chrome carbon steel

Steel balls for ball bearings are generally made of __________ steel. (A) Cast (B) Stainless (C) Free carbon (D) Carbon chrome

Description : Steel balls for ball bearings are generally made of __________ steel. (A) Cast (B) Stainless (C) Free carbon (D) Carbon chrome

Last Answer : (D) Carbon chrome

Ball bearings are normally made of __________ steel. (A) High speed (B) High carbon (C) Chrome (D) Silicon

Description : Ball bearings are normally made of __________ steel. (A) High speed (B) High carbon (C) Chrome (D) Silicon

Last Answer : (C) Chrome

Ball bearings are, usually, made from (a) low carbon steel (b) high carbon steel (c) medium carbon steel (d) chrome steel

Description : Ball bearings are, usually, made from (a) low carbon steel (b) high carbon steel (c) medium carbon steel (d) chrome steel

Last Answer : (d) chrome steel

The ball bearing is subjected to a radial load of 4000 N. Expected life for 90% bearings is 9000 hr and the shaft is rot (a) 42.21 kN (b) 37.29 kN (c) 26.33 kN (d) 35.22 kN

Description : The ball bearing is subjected to a radial load of 4000 N. Expected life for 90% bearings is 9000 hr and the shaft is rot (a) 42.21 kN (b) 37.29 kN (c) 26.33 kN (d) 35.22 kN

Last Answer : (b) 37.29 kN

Which of the following cannot tolerate misalignment? (a) Angular contact bearing (b) Cylinder roller bearing (c) Thrust ball bearings (d) All of the listed

Description : Which of the following cannot tolerate misalignment? (a) Angular contact bearing (b) Cylinder roller bearing (c) Thrust ball bearings (d) All of the listed

Last Answer : (d) All of the listed

Which of the bearings given below SHOULD NOT be subjected to a thrust load? (a) Deep groove ball bearing (b) Angular contact ball bearing (c) Cylindrical (straight) roller bearing (d) Single row tapered roller bearing

Description : Which of the bearings given below SHOULD NOT be subjected to a thrust load? (a) Deep groove ball bearing (b) Angular contact ball bearing (c) Cylindrical (straight) roller bearing (d) Single row tapered roller bearing

Last Answer : (c) Cylindrical (straight) roller bearing

Deep groove ball bearings are used for (a) heavy thrust load only (b) the small angular displacement of shafts (c) radial load at high speed (d) combined thrust and radial loads at high speed

Description : Deep groove ball bearings are used for (a) heavy thrust load only (b) the small angular displacement of shafts (c) radial load at high speed (d) combined thrust and radial loads at high speed

Last Answer : (d) combined thrust and radial loads at high speed

There is a problem of alignment in deep groove ball bearings. (a) Yes (b) No, it is self-aligning (c) It aligns itself only in some particular cases (d) Can’t be determined

Description : There is a problem of alignment in deep groove ball bearings. (a) Yes (b) No, it is self-aligning (c) It aligns itself only in some particular cases (d) Can’t be determined

Last Answer : (a) Yes

Deep groove ball bearings create a lot of noise. (a) Yes (b) Depends on the application (c) They create very less noise (d) No reference frame for comparison is mentioned

Description : Deep groove ball bearings create a lot of noise. (a) Yes (b) Depends on the application (c) They create very less noise (d) No reference frame for comparison is mentioned

Last Answer : (c) They create very less noise

Antifriction bearings are (a) thick lubricated bearings (b) plastic bearings (c) ball and roller bearings (d) thin lubricated bearings

Description : Antifriction bearings are (a) thick lubricated bearings (b) plastic bearings (c) ball and roller bearings (d) thin lubricated bearings

Last Answer : (c) ball and roller bearings

The ball bearings are provided with a cage (a) to reduce friction (b) to facilitate slipping of balls (c) to prevent the lubricant from flowing out (d) to maintain the balls at a fixed distance apart

Description : The ball bearings are provided with a cage (a) to reduce friction (b) to facilitate slipping of balls (c) to prevent the lubricant from flowing out (d) to maintain the balls at a fixed distance apart

Last Answer : (d) to maintain the balls at a fixed distance apart

Match List -I (Bearings) with List-II (Applications) and select the using the codes given below the lists: [IAS-1998] List –I List-II A. Journal bearing 1. Electric motors B. Thrust bearing 2. Watches C. Conical pivot bearing 3. Marine engines D. Ball bearing 4. Swivelling chairs A B C D A B C D (a) 3 4 1 2 (b) 4 2 1 3 (c) 3 4 2 1 (d) 4 2 3 1

Description : Match List -I (Bearings) with List-II (Applications) and select the using the codes given below the lists: [IAS-1998] List -I List-II A. Journal bearing 1. Electric motors B. Thrust bearing 2. Watches C. Conical pivot bearing 3. Marine ... D (a) 3 4 1 2 (b) 4 2 1 3 (c) 3 4 2 1 (d) 4 2 3 1

Last Answer : (c) 3 4 2 1

Which one of the following pair is correctly matched? [IES-2000] (a) Beauchamp tower ........................First experiments on journal bearings (b) Osborne Reynolds ........................Antifriction bearings (c) Somerfield number........................Pivot and Collar bearings (d) Ball bearings...............................Hydrodynamic lubrication

Description : Which one of the following pair is correctly matched? [IES-2000] (a) Beauchamp tower ........................First experiments on journal bearings (b) Osborne Reynolds ........................ ... .Pivot and Collar bearings (d) Ball bearings...............................Hydrodynamic lubrication

Last Answer : (a) Beauchamp tower ........................First experiments on journal bearings

Match List I with List II and select the : [IES-2002] List I (Bearings) List II (Load type) A. Hydrodynamic Journal bearing 1. High radial and thrust load combined B. Rectangular Hydrostatic bearing 2. Radial load only C. Taper Roller bearing 3. Thrust load only D. Angular contact ball bearing 4. Medium to low radial and thrust combined A B C D A B C D (a) 2 3 1 4 (b) 4 1 3 2 (c) 2 1 3 4 (d) 4 3 1 2

Description : Match List I with List II and select the : [IES-2002] List I (Bearings) List II (Load type) A. Hydrodynamic Journal bearing 1. High radial and thrust load combined B. Rectangular Hydrostatic bearing 2. Radial load only C. Taper Roller ... (a) 2 3 1 4 (b) 4 1 3 2 (c) 2 1 3 4 (d) 4 3 1 2

Last Answer : (a) 2 3 1 4

Which of the following cannot tolerate misalignment? a) Angular contact bearing b) Cylinder roller bearing c) Thrust ball bearings d) All of the listed

Description : Which of the following cannot tolerate misalignment? a) Angular contact bearing b) Cylinder roller bearing c) Thrust ball bearings d) All of the listed

Last Answer : d) All of the listed

There is problem of alignment in deep groove ball bearings. a) Yes b) No, it is self-aligning c) It aligns itself only in some particular cases d) Can’t be determined

Description : There is problem of alignment in deep groove ball bearings. a) Yes b) No, it is self-aligning c) It aligns itself only in some particular cases d) Can’t be determined

Last Answer : a) Yes

Deep groove ball bearings creates a lot of noise. a) Yes b) They create very less noise c) Depends on the application d) No reference frame for comparison is mentioned

Description : Deep groove ball bearings creates a lot of noise. a) Yes b) They create very less noise c) Depends on the application d) No reference frame for comparison is mentioned

Last Answer : b) They create very less noise

The bearings which resist radial loads is known as a) Ball bearing b) bush bearing c) thrust bearing d) journal bearing

Description : The bearings which resist radial loads is known as a) Ball bearing b) bush bearing c) thrust bearing d) journal bearing

Last Answer : d) journal bearing

When did the first ball bearings Skates came into life?

Description : When did the first ball bearings Skates came into life?

Last Answer : Ans. December 9th 1884.

The function of ball bearings in a wheel is : (1) to increase friction (2) to convert kinetic friction into rolling friction (3) to convert static friction into kinetic friction (4) just for convenience

Description : The function of ball bearings in a wheel is : (1) to increase friction (2) to convert kinetic friction into rolling friction (3) to convert static friction into kinetic friction (4) just for convenience

Last Answer : to convert kinetic friction into rolling friction

On large generators, space heaters are used to ____________. A. keep the machine at ambient tmperature of the machinery space B. maintain rotor and stator winding temperatures above the dew point to prevent the formation of condensation C. prevent condensation in the lube oil D. prevent electrolysis due to condensation in the bearings

Description : On large generators, space heaters are used to ____________. A. keep the machine at ambient tmperature of the machinery space B. maintain rotor and stator winding temperatures above the dew point ... C. prevent condensation in the lube oil D. prevent electrolysis due to condensation in the bearings

Last Answer : Answer: B

To protect the rotor of a motor disassembled for maintenance or overhaul, it should be ___________________. A. suspended by wire slings in one corner of the shop B. stowed upright on its shaft C. supported by two 'V' notched wood blocks D. returned to the frame as soon as the bearings are removed

Description : To protect the rotor of a motor disassembled for maintenance or overhaul, it should be ___________________. A. suspended by wire slings in one corner of the shop B. stowed upright on its shaft C. supported by two 'V' notched wood blocks D. returned to the frame as soon as the bearings are removed

Last Answer : Answer: C

On electrical generators one of the bearings is isolated from the bedplate. This insulating block should not be painted and must be kept clean to ___________. A. protect operating personnel from shock B. create an isolated ground for the instrumentation C. allow for the expansion of the generator away from the prime mover as it warms up D. eliminate shaft currents to prevent damaging the bearings

Description : On electrical generators one of the bearings is isolated from the bedplate. This insulating block should not be painted and must be kept clean to ___________. A. protect operating personnel from shock ... the prime mover as it warms up D. eliminate shaft currents to prevent damaging the bearings

Last Answer : Answer: D

If the bearings of an electrical generator are failing more frequently than expected and the lubricating oil is sludging then you should ______________. A. check the connections to the output leads B. check the bearing insulating block on one end of the unit C. replace the bearing with a sealed roller type D. replace the thrust bearing of the prime mover

Description : If the bearings of an electrical generator are failing more frequently than expected and the lubricating oil is sludging then you should ______________. A. check the connections to the output leads B. ... replace the bearing with a sealed roller type D. replace the thrust bearing of the prime mover

Last Answer : Answer: B

The following air gap readings were obtained from a horizontally mounted, bilge pump, induction motor, equipped with sleeve bearings: FWD END-AFT END, Top .045 - .049, Right Side .045 - .047, Left Side .045 - .047, Bottom .045 - .041 Which of the f A. both the aft and foward bearings should be replaced. B. Shims should be removed from the aft bearing. C. The forward bearing should be lowered. D. The aft bearing should be lowered.

Description : The following air gap readings were obtained from a horizontally mounted, bilge pump, induction motor, equipped with sleeve bearings: FWD END-AFT END, Top .045 - .049, Right Side .045 - .047, Left ... the aft bearing. C. The forward bearing should be lowered. D. The aft bearing should be lowered.

Last Answer : Answer: A

Air gap readings should be taken on electrical generation machinery periodicly to _________. I. determine the need for cleaning II. check the condition of the bearings A. I only B. II only C. both I and II D. neither I or II

Description : Air gap readings should be taken on electrical generation machinery periodicly to _________. I. determine the need for cleaning II. check the condition of the bearings A. I only B. II only C. both I and II D. neither I or II

Last Answer : Answer: B

Air gap readings for electrical generating equipment should be taken periodicly. This is to _______. I. determine the condition of the bearings II. prevent damage to the rotor and stator A. I only B. II only C. both I and II D. neither I or II

Description : Air gap readings for electrical generating equipment should be taken periodicly. This is to _______. I. determine the condition of the bearings II. prevent damage to the rotor and stator A. I only B. II only C. both I and II D. neither I or II

Last Answer : Answer: C

If air gap readings for an electical generating machine have changed significantly from the last reading, you should check _________. A. the bearings B. insulation readings and machine cleanliness C. the prime mover thrust bearing D. the field coil bolts for the proper torque values

Description : If air gap readings for an electical generating machine have changed significantly from the last reading, you should check _________. A. the bearings B. insulation readings and machine cleanliness C. the prime mover thrust bearing D. the field coil bolts for the proper torque values

Last Answer : Answer: A

Air gap readings should be taken periodicly on electrical generation equipment to __________. A. determine the amount of varnish that can be applied to correct insulation problems B. determine the condition of the bearings C. provide for the correct proper tightening of the field coil bolts and correct lateral adjustment of the field coils D. increase machine efficiency

Description : Air gap readings should be taken periodicly on electrical generation equipment to __________. A. determine the amount of varnish that can be applied to correct insulation problems B. determine the ... field coil bolts and correct lateral adjustment of the field coils D. increase machine efficiency

Last Answer : Answer: B

To protect the rotor of a motor disassembled for maintenance or overhaul, it should be ___________________. A. suspended by wire slings in one corner of the shop B. wrapped in several layers of heavy paper or cardboard C. supported by flat wood blocks on the workbench D. returned to the frame as soon as the bearings are removed

Description : To protect the rotor of a motor disassembled for maintenance or overhaul, it should be ___________________. A. suspended by wire slings in one corner of the shop B. wrapped in several layers of heavy ... flat wood blocks on the workbench D. returned to the frame as soon as the bearings are removed

Last Answer : Answer: B

A split-phase induction squirrel-cage motor will not come up to speed, even though the rated voltage, rated frequency, and rated load are applied. The suspected trouble could be due to _____________. A. a faulty centrifugal switch B. broken rotor bars C. worn bearings D. all of the above

Description : A split-phase induction squirrel-cage motor will not come up to speed, even though the rated voltage, rated frequency, and rated load are applied. The suspected trouble could be due to _____________. A. a faulty centrifugal switch B. broken rotor bars C. worn bearings D. all of the above

Last Answer : Answer: D

When disassembling electric motors for maintenance or overhaul, ________________. A. punch mark frame and end bells for proper assembly B. wrap bearings in lint free cloths if they are to be reused C. tag and store small parts in a box D. all of the above

Description : When disassembling electric motors for maintenance or overhaul, ________________. A. punch mark frame and end bells for proper assembly B. wrap bearings in lint free cloths if they are to be reused C. tag and store small parts in a box D. all of the above

Last Answer : Answer: D

The reactive power drawn by a motor from an AC generator is the power which is _____________. A. used to establish the magnetic field of the motor B. lost in overcoming friction in the bearings C. strictly converted to heat generated by current flow through the windings D. transmitted directly through the rotor shaft to perform useful work

Description : The reactive power drawn by a motor from an AC generator is the power which is _____________. A. used to establish the magnetic field of the motor B. lost in overcoming friction in the ... by current flow through the windings D. transmitted directly through the rotor shaft to perform useful work

Last Answer : Answer: A

One of the generator or motor bearings is generally insulated from the end housing in order to prevent ________. A. rapid brush wear B. current leakage from the shaft C. excessive field winding heat D. circulation of shaft currents induced in the machine's frame

Description : One of the generator or motor bearings is generally insulated from the end housing in order to prevent ________. A. rapid brush wear B. current leakage from the shaft C. excessive field winding heat D. circulation of shaft currents induced in the machine's frame

Last Answer : Answer: D

The following air gap readings were obtained from a horizontally mounted, bilge pump, induction motor, equipped with sleeve bearings: FWD END -AFT END, Top .045 - .049 , Right Side .045 - .047, Left Side .045 - .047 , Bottom .045 - .041 Which of the fo A. The aft bearing should be realigned or replaced. B. Shims should be removed from the aft bearing. C. The forward bearing should be lowered. D. The aft bearing should be lowered.

Description : The following air gap readings were obtained from a horizontally mounted, bilge pump, induction motor, equipped with sleeve bearings: FWD END -AFT END, Top .045 - .049 , Right Side .045 - .047, Left ... the aft bearing. C. The forward bearing should be lowered. D. The aft bearing should be lowered.

Last Answer : Answer: A

In the illustrated motor, roller bearings are used because __________. EL-0001 A. of their ability to absorb moderate thrust loads B. they electrically insulate the rotor from the frame reducing cross-currents C. the shafting and end bells do not require as close a tolerance to properly fit this type of bearing D. the clearance between the rotor and stator is generally as close as mechanical tolerance will permit

Description : In the illustrated motor, roller bearings are used because __________. EL-0001 A. of their ability to absorb moderate thrust loads B. they electrically insulate the rotor from the frame reducing ... clearance between the rotor and stator is generally as close as mechanical tolerance will permit

Last Answer : Answer: D

The air gap in an induction motor should be periodically checked with a feeler gage to prevent possible ___________. A. rotor contact with the stator B. axial misalignment of the rotor C. damage to the motor bearings D. electrical damage to the bearings

Description : The air gap in an induction motor should be periodically checked with a feeler gage to prevent possible ___________. A. rotor contact with the stator B. axial misalignment of the rotor C. damage to the motor bearings D. electrical damage to the bearings

Last Answer : Answer: A

Before reassembling any machinery, you should _____________. A. replace all bearings regardless of length of service B. apply a heavy coat of oil to all mating surfaces C. clean any corroded surfaces and file all burrs smooth D. coat all parts with alemite grease

Description : Before reassembling any machinery, you should _____________. A. replace all bearings regardless of length of service B. apply a heavy coat of oil to all mating surfaces C. clean any corroded surfaces and file all burrs smooth D. coat all parts with alemite grease

Last Answer : Answer: C

What are the causes of failure of bearings?

Description : What are the causes of failure of bearings?

Last Answer : a) Faulty mounting b) Faulty lubrication c) Foreign matter in lubrication d) Water in the bearing arrangement e) Vibration f) Inoccurrences of form of shaft or housing seating. g) Passage of electric current. h) Metal fatigue