There is problem of alignment in deep groove ball bearings. a) Yes b) No, it is self-aligning c) It aligns itself only in some particular cases d) Can’t be determined

There is problem of alignment in deep groove ball bearings.

a) Yes

b) No, it is self-aligning

c) It aligns itself only in some particular cases

d) Can’t be determined
by

1 Answer

Answer :

a) Yes
by

Related questions

There is a problem of alignment in deep groove ball bearings. (a) Yes (b) No, it is self-aligning (c) It aligns itself only in some particular cases (d) Can’t be determined

Description : There is a problem of alignment in deep groove ball bearings. (a) Yes (b) No, it is self-aligning (c) It aligns itself only in some particular cases (d) Can’t be determined

Last Answer : (a) Yes

Match List-I (Type of Anti-friction bearing) with List-II (Specific Use) and select the using the code given below the Lists: [IES-2006] List-I List -II A. Self-aligning ball bearing 1. For pure axial load B. Taper roller bearing 2. For hinged condition C. Deep groove ball bearing 3. For pure radial load D. Thrust ball bearing 4. For axial and radial load A B C D A B C D (a) 2 1 3 4 (b) 3 4 2 1 (c) 2 4 3 1 (d) 3 1 2 4

Description : Match List-I (Type of Anti-friction bearing) with List-II (Specific Use) and select the using the code given below the Lists: [IES-2006] List-I List -II A. Self-aligning ball bearing 1. For pure axial load B. Taper roller bearing 2. For ... C D (a) 2 1 3 4 (b) 3 4 2 1 (c) 2 4 3 1 (d) 3 1 2 4

Last Answer : (c) 2 4 3 1

Deep groove ball bearings create a lot of noise. (a) Yes (b) Depends on the application (c) They create very less noise (d) No reference frame for comparison is mentioned

Description : Deep groove ball bearings create a lot of noise. (a) Yes (b) Depends on the application (c) They create very less noise (d) No reference frame for comparison is mentioned

Last Answer : (c) They create very less noise

Deep groove ball bearings creates a lot of noise. a) Yes b) They create very less noise c) Depends on the application d) No reference frame for comparison is mentioned

Description : Deep groove ball bearings creates a lot of noise. a) Yes b) They create very less noise c) Depends on the application d) No reference frame for comparison is mentioned

Last Answer : b) They create very less noise

Deep groove ball bearings are used for (a) heavy thrust load only (b) the small angular displacement of shafts (c) radial load at high speed (d) combined thrust and radial loads at high speed

Description : Deep groove ball bearings are used for (a) heavy thrust load only (b) the small angular displacement of shafts (c) radial load at high speed (d) combined thrust and radial loads at high speed

Last Answer : (d) combined thrust and radial loads at high speed

Which of the bearings given below SHOULD NOT be subjected to a thrust load? (a) Deep groove ball bearing (b) Angular contact ball bearing (c) Cylindrical (straight) roller bearing (d) Single row tapered roller bearing

Description : Which of the bearings given below SHOULD NOT be subjected to a thrust load? (a) Deep groove ball bearing (b) Angular contact ball bearing (c) Cylindrical (straight) roller bearing (d) Single row tapered roller bearing

Last Answer : (c) Cylindrical (straight) roller bearing

The construction feature which makes tapered roller bearings unique in that races are (a) attachable (b) separable (c) self-aligning (d) none of the mentioned

Description : The construction feature which makes tapered roller bearings unique in that races are (a) attachable (b) separable (c) self-aligning (d) none of the mentioned

Last Answer : (b) separable

The deep groove ball bearing has immense rigidity. (a) True (b) No, it has point contact and hence low rigidity (c) It has surface contact (d) It has line contact

Description : The deep groove ball bearing has immense rigidity. (a) True (b) No, it has point contact and hence low rigidity (c) It has surface contact (d) It has line contact

Last Answer : (b) No, it has point contact and hence low rigidity

Deep groove ball bearing has immense rigidity. a) True b) No it has point contact and hence low rigidity c) It has surface contact d) It has line contact

Description : Deep groove ball bearing has immense rigidity. a) True b) No it has point contact and hence low rigidity c) It has surface contact d) It has line contact

Last Answer : b) No it has point contact and hence low rigidity

Which one of the following bearing is intended for a very heavy radial load? (a) Ball bearing (b) Self-aligning roller bearing (c) Roller bearing (d) Thrust bearing

Description : Which one of the following bearing is intended for a very heavy radial load? (a) Ball bearing (b) Self-aligning roller bearing (c) Roller bearing (d) Thrust bearing

Last Answer : (b) Self-aligning roller bearing

A cylinder roller creates lesser noise than a deep groove ball bearing. (a) True (b) False

Description : A cylinder roller creates lesser noise than a deep groove ball bearing. (a) True (b) False

Last Answer : (b) False

Cylindrical roller bearing has a lower load capacity as compared to deep groove ball bearing. (a) True (b) False

Description : Cylindrical roller bearing has a lower load capacity as compared to deep groove ball bearing. (a) True (b) False

Last Answer : (b) False

Cylinder roller creates lesser noise than deep groove ball bearing. a) True b) False

Description : Cylinder roller creates lesser noise than deep groove ball bearing. a) True b) False

Last Answer : b) False

Cylindrical load bearing has lower load capacity as compared to deep groove ball bearing. a) True b) False

Description : Cylindrical load bearing has lower load capacity as compared to deep groove ball bearing. a) True b) False

Last Answer : b) False

Balls and the races of the deep groove ball may roll freely without any sliding. a) True b) False

Description : Balls and the races of the deep groove ball may roll freely without any sliding. a) True b) False

Last Answer : a) True

Set screws are subjected to tensile forces only. a) Yes b) No, they are subjected to compressive forces only c) Both compressive and tensile d) Can’t be determined

Description : Set screws are subjected to tensile forces only. a) Yes b) No, they are subjected to compressive forces only c) Both compressive and tensile d) Can’t be determined

Last Answer : b) No, they are subjected to compressive forces only

Bending stress in graduated length leaves are more than that in full length leaves. a) Yes b) No c) In some cases d) Can’t be stated

Description : Bending stress in graduated length leaves are more than that in full length leaves. a) Yes b) No c) In some cases d) Can’t be stated

Last Answer : b) No

The rolling contact bearings as compared to sliding contact bearings have (a) small overall dimensions (b) accuracy of shaft alignment (c) low starting and low running friction except at very high speeds (d) all the mentioned

Description : The rolling contact bearings as compared to sliding contact bearings have (a) small overall dimensions (b) accuracy of shaft alignment (c) low starting and low running friction except at very high speeds (d) all the mentioned

Last Answer : (d) all the mentioned

Spiral spring is quite rigid. a) Yes b) No it is flexible c) It is of moderate rigidity d) Rigidity can’t be determined

Description : Spiral spring is quite rigid. a) Yes b) No it is flexible c) It is of moderate rigidity d) Rigidity can’t be determined

Last Answer : b) No it is flexible

Match List I with List II and select the : [IES-2002] List I (Bearings) List II (Load type) A. Hydrodynamic Journal bearing 1. High radial and thrust load combined B. Rectangular Hydrostatic bearing 2. Radial load only C. Taper Roller bearing 3. Thrust load only D. Angular contact ball bearing 4. Medium to low radial and thrust combined A B C D A B C D (a) 2 3 1 4 (b) 4 1 3 2 (c) 2 1 3 4 (d) 4 3 1 2

Description : Match List I with List II and select the : [IES-2002] List I (Bearings) List II (Load type) A. Hydrodynamic Journal bearing 1. High radial and thrust load combined B. Rectangular Hydrostatic bearing 2. Radial load only C. Taper Roller ... (a) 2 3 1 4 (b) 4 1 3 2 (c) 2 1 3 4 (d) 4 3 1 2

Last Answer : (a) 2 3 1 4

Ball bearings are, usually, made from (a) low carbon steel (b) high carbon steel (c) medium carbon steel (d) chrome steel

Description : Ball bearings are, usually, made from (a) low carbon steel (b) high carbon steel (c) medium carbon steel (d) chrome steel

Last Answer : (d) chrome steel

The ball bearing is subjected to a radial load of 4000 N. Expected life for 90% bearings is 9000 hr and the shaft is rot (a) 42.21 kN (b) 37.29 kN (c) 26.33 kN (d) 35.22 kN

Description : The ball bearing is subjected to a radial load of 4000 N. Expected life for 90% bearings is 9000 hr and the shaft is rot (a) 42.21 kN (b) 37.29 kN (c) 26.33 kN (d) 35.22 kN

Last Answer : (b) 37.29 kN

Which of the following cannot tolerate misalignment? (a) Angular contact bearing (b) Cylinder roller bearing (c) Thrust ball bearings (d) All of the listed

Description : Which of the following cannot tolerate misalignment? (a) Angular contact bearing (b) Cylinder roller bearing (c) Thrust ball bearings (d) All of the listed

Last Answer : (d) All of the listed

Antifriction bearings are (a) thick lubricated bearings (b) plastic bearings (c) ball and roller bearings (d) thin lubricated bearings

Description : Antifriction bearings are (a) thick lubricated bearings (b) plastic bearings (c) ball and roller bearings (d) thin lubricated bearings

Last Answer : (c) ball and roller bearings

The ball bearings are provided with a cage (a) to reduce friction (b) to facilitate slipping of balls (c) to prevent the lubricant from flowing out (d) to maintain the balls at a fixed distance apart

Description : The ball bearings are provided with a cage (a) to reduce friction (b) to facilitate slipping of balls (c) to prevent the lubricant from flowing out (d) to maintain the balls at a fixed distance apart

Last Answer : (d) to maintain the balls at a fixed distance apart

Match List -I (Bearings) with List-II (Applications) and select the using the codes given below the lists: [IAS-1998] List –I List-II A. Journal bearing 1. Electric motors B. Thrust bearing 2. Watches C. Conical pivot bearing 3. Marine engines D. Ball bearing 4. Swivelling chairs A B C D A B C D (a) 3 4 1 2 (b) 4 2 1 3 (c) 3 4 2 1 (d) 4 2 3 1

Description : Match List -I (Bearings) with List-II (Applications) and select the using the codes given below the lists: [IAS-1998] List -I List-II A. Journal bearing 1. Electric motors B. Thrust bearing 2. Watches C. Conical pivot bearing 3. Marine ... D (a) 3 4 1 2 (b) 4 2 1 3 (c) 3 4 2 1 (d) 4 2 3 1

Last Answer : (c) 3 4 2 1

Which one of the following pair is correctly matched? [IES-2000] (a) Beauchamp tower ........................First experiments on journal bearings (b) Osborne Reynolds ........................Antifriction bearings (c) Somerfield number........................Pivot and Collar bearings (d) Ball bearings...............................Hydrodynamic lubrication

Description : Which one of the following pair is correctly matched? [IES-2000] (a) Beauchamp tower ........................First experiments on journal bearings (b) Osborne Reynolds ........................ ... .Pivot and Collar bearings (d) Ball bearings...............................Hydrodynamic lubrication

Last Answer : (a) Beauchamp tower ........................First experiments on journal bearings

Which of the following cannot tolerate misalignment? a) Angular contact bearing b) Cylinder roller bearing c) Thrust ball bearings d) All of the listed

Description : Which of the following cannot tolerate misalignment? a) Angular contact bearing b) Cylinder roller bearing c) Thrust ball bearings d) All of the listed

Last Answer : d) All of the listed

The failure of ball bearings used in electric motors can result from _____________. A. failure to clean the bearing before repacking B. failure to maintain proper alignment C. excess lubrication forcing the bearing full of grease and eliminating all areas of expansion D. all of the above

Description : The failure of ball bearings used in electric motors can result from _____________. A. failure to clean the bearing before repacking B. failure to maintain proper alignment C. excess lubrication forcing the bearing full of grease and eliminating all areas of expansion D. all of the above

Last Answer : Answer: D

Sliding contact bearings, also called plain bearings have no problem of wear. a) True b) False

Description : Sliding contact bearings, also called plain bearings have no problem of wear. a) True b) False

Last Answer : b) False

Alignment of cutter bar is a) Aligning centers of guard and knife b) Keeping cutter bur in 88 degrees c) Both d) None of these Ans. b

Description : Alignment of cutter bar is a) Aligning centers of guard and knife b) Keeping cutter bur in 88 degrees c) Both d) None of these Ans. b

Last Answer : ans b

A pulsar is a rapidly spinning neutron star which emits: A. A blinding light when it aligns with the planets B. Radio waves detectable from Earth (Answer) C. A gravitational pull which attracts high energy dust particles D. Enough energy to power itself indefinitely

Description : A pulsar is a rapidly spinning neutron star which emits: A. A blinding light when it aligns with the planets B. Radio waves detectable from Earth (Answer) C. A gravitational pull which attracts high energy dust particles D. Enough energy to power itself indefinitely

Last Answer : B. Radio waves detectable from Earth (Answer)

Knuckle Joint can’t be used to connect two intersecting rods. a) Yes b) No, it can’t be used c) It can be used with some modificatios d) It is expensive and hence isn’t used

Description : Knuckle Joint can’t be used to connect two intersecting rods. a) Yes b) No, it can’t be used c) It can be used with some modificatios d) It is expensive and hence isn’t used

Last Answer : b) No, it can’t be used

All welding processes require pressure along with heat. a) Yes b) No, fusion doesn’t require c) Can’t be stated d) None of the listed

Description : All welding processes require pressure along with heat. a) Yes b) No, fusion doesn’t require c) Can’t be stated d) None of the listed

Last Answer : b) No, fusion doesn’t require

Type of welded joint which do not exit (i) Groove type (ii) Spot type (iii)Plug type (iv) Surface type

Description : Type of welded joint which do not exit (i) Groove type (ii) Spot type (iii)Plug type (iv) Surface type

Last Answer : (iv) Surface type

In which case, molten metal is used to do welding? (i) Groove type (ii) spot type (iii) Plug type (iv) None

Description : In which case, molten metal is used to do welding? (i) Groove type (ii) spot type (iii) Plug type (iv) None

Last Answer : (iii) Plug type

Partial bearing is preferred over journal bearing. a) True b) No c) More friction losses d) Can’t be determined

Description : Partial bearing is preferred over journal bearing. a) True b) No c) More friction losses d) Can’t be determined

Last Answer : a) True

The angular play bearing must be mounted without axial play. a) Yes b) Little tolerance is adjusted c) Little tolerance is necessary d) Can’t be stated

Description : The angular play bearing must be mounted without axial play. a) Yes b) Little tolerance is adjusted c) Little tolerance is necessary d) Can’t be stated

Last Answer : a) Yes

What is the device, which depends on the action of a movalbe permanent magnet, in aligning itself in the resultant field produced by a fixed permanent magnet or current- carrying coils whose axes are displaced by a fixed angle?

Description : What is the device, which depends on the action of a movalbe permanent magnet, in aligning itself in the resultant field produced by a fixed permanent magnet or current- carrying coils whose axes are displaced by a fixed angle?

Last Answer : moving-magnet instrument

Tapered roller bearings can take (a) radial load only (b) axial load only (c) both radial and axial loads and the ratio of these being greater than unity (d) both radial and axial loads and the ratio of these being less than unity

Description : Tapered roller bearings can take (a) radial load only (b) axial load only (c) both radial and axial loads and the ratio of these being greater than unity (d) both radial and axial loads and the ratio of these being less than unity

Last Answer : (c) both radial and axial loads and the ratio of these being greater than unity

The tapered roller bearings can take (a) radial load only (b) axial load only (c) both radial and axial loads (d) none of the mentioned

Description : The tapered roller bearings can take (a) radial load only (b) axial load only (c) both radial and axial loads (d) none of the mentioned

Last Answer : (c) both radial and axial loads

In sliding contact bearings, a positive pressure can be built up and a load supported by a fluid only by the use of a: [IES-2005] (a) Diverging film (b) Converging-diverging film (c) Converging film (d) Flat film

Description : In sliding contact bearings, a positive pressure can be built up and a load supported by a fluid only by the use of a: [IES-2005] (a) Diverging film (b) Converging-diverging film (c) Converging film (d) Flat film

Last Answer : (c) Converging film

In hydrostatic bearings (A) The Oil film pressure is generated only by the rotation of the journal (B) The oil film is maintained by supplying oil under pressure (C) Do not require external supply of lubricant (D) Grease is used for lubrication

Description : In hydrostatic bearings (A) The Oil film pressure is generated only by the rotation of the journal (B) The oil film is maintained by supplying oil under pressure (C) Do not require external supply of lubricant (D) Grease is used for lubrication

Last Answer : (B) The oil film is maintained by supplying oil under pressure

When the driving torque is more than load torque, flywheel is ______ 1. Accelerated 2. Decelerated 3. Constant velocity 4. Can’t be determined

Description : When the driving torque is more than load torque, flywheel is ______ 1. Accelerated 2. Decelerated 3. Constant velocity 4. Can’t be determined

Last Answer : 1. Accelerated

When the driving torque is more than load torque, flywheel is ______ a) Accelerated b) Decelerated c) Constant velocity d) Can’t be determined

Description : When the driving torque is more than load torque, flywheel is ______ a) Accelerated b) Decelerated c) Constant velocity d) Can’t be determined

Last Answer : a) Accelerated

A clearance bearing is design accurately to keep the radius of journal and bearing equal. a) Journal radius is kept larger b) Journal radius is kept smaller c) True d) Can’t be determined

Description : A clearance bearing is design accurately to keep the radius of journal and bearing equal. a) Journal radius is kept larger b) Journal radius is kept smaller c) True d) Can’t be determined

Last Answer : b) Journal radius is kept smaller

When two Belleville springs are in parallel, half force is obtained for a given deflection. a) Half force b) Double force c) Same force d) Can’t be determined

Description : When two Belleville springs are in parallel, half force is obtained for a given deflection. a) Half force b) Double force c) Same force d) Can’t be determined

Last Answer : b) Double force

Involute splines have stub teeth with a pressure angle of ___ a) 30 b) 45 c) 60 d) Can’t be determined

Description : Involute splines have stub teeth with a pressure angle of ___ a) 30 b) 45 c) 60 d) Can’t be determined

Last Answer : b) 45

Involute splines have stub teeth with a pressure angle of ___ a) 30 b) 45 c) 60 d) Can’t be determined

Description : Involute splines have stub teeth with a pressure angle of ___ a) 30 b) 45 c) 60 d) Can’t be determined

Last Answer : b) 45

For an elliptical hole on a flat plate, if width of the hole in direction of the load decrease, Stress Concentration Factor will______ a) Increase b) Decrease c) Remains constant d) Can’t be determined. Varies from material to material

Description : For an elliptical hole on a flat plate, if width of the hole in direction of the load decrease, Stress Concentration Factor will______ a) Increase b) Decrease c) Remains constant d) Can’t be determined. Varies from material to material

Last Answer : a) Increase