Description : The region of safety for biaxial stresses is of which shape in the case of maximum distortion energy theorem. a) Ellipse b) Circle c) Rectangle d) Square
Last Answer : a) Ellipse
Description : If compressive yield stress and tensile yield stress are equivalent, then region of safety from maximum principal stress theory is of which shape? a) Rectangle b) Square c) Circle d) Ellipse
Last Answer : b) Square
Description : In distortion energy theorem, if a unit cube is subjected to biaxial stress, then S(yt) is given by which of the following? a) √ (σ12- σ1σ2 +σ22) b) σ12- σ1σ2 +σ22 c) √ (σ12+ σ1σ2 +σ22) d) σ12+ σ1σ2 +σ22
Last Answer : a) √ (σ12- σ1σ2 +σ22)
Description : The region of safety in maximum shear stress theory contains which of the given shape a) Hexagon b) Rectangle c) Square d) None of the mentioned
Last Answer : a) Hexagon
Description : If harmonic motion of same frequency and same phase are superimposed in two perpendicular directions ( x and y) then, the resultant motion will be, A) circle B) An ellipse C) An square D) An rectangle
Last Answer : C) An square
Description : Distortion energy theorem is not recommended for ductile materials. a) True b) False
Last Answer : b) False
Description : In a DFD external entities are represented by a A) Rectangle B) Ellipse C) Diamond shaped box D) Circle
Last Answer : A) Rectangle
Description : Ellipse of stress is used to find a. Resultant stress on any plane in a bi-axial stress system b. Resultant stress on any plane in a general two dimensional system c. Maximum shear stress d. Location of planes of maximum shear stress
Last Answer : a. Resultant stress on any plane in a bi-axial stress system
Description : Among maximum shear stress theory and distortion energy theory, which gives the higher value shear yield strength? a) Maximum shear stress theory b) Distortion energy theory c) Both give equal values d) Vary from material to material
Last Answer : b) Distortion energy theory
Description : A transmission shaft subjected to pure bending moment should be designed on the basis of (A) Maximum principal stress theory (B) Maximum shear stress theory (C) Distortion energy theory (D) Goodman or Soderberg diagrams
Last Answer : (A) Maximum principal stress theory
Description : Distortion energy theory is slightly liberal as compared to maximum shear stress theory. a) True b) False
Last Answer : a) True
Description : Which of the following stresses can be determined using Mohr's circle method? a. Torsional stress b. Bending stress c. Principal stress d. All of the above
Last Answer : c. Principal stress
Description : __________ shape is used to make codebook in structure vector quantization. a. Square b. Rectangle c. Circle d. Hexagon
Last Answer : d. Hexagon
Description : If a rectangle were called a circle, a circle a point, a point a triangle and a triangle a square, the shape of a wheel is (A) Rectangle (B) Circle (C) Point (D) Triangle
Last Answer : (C) Point
Description : The maximum number of principal stresses is a. 1 b. 3 c. 5 d. None
Last Answer : b. 3
Description : The maximum number of principal stresses is a. 2 b. 4 c. 6 d. None
Last Answer : d. None
Description : Maximum shear stress in terms of principal stresses is a. Firstly (σ 1 +σ 2 )/2 b. Secondly (σ 1 /σ 2 ) c. Thirdly (σ 1 –σ 2 )/2 d. None
Last Answer : c. Thirdly (σ 1 –σ 2 )/2
Description : How many maximum shear stresses are there with three principal stresses? a. 1 b. 2 c. 3 d. None
Last Answer : c. 3
Description : Principal stresses are a. Firstly Maximum and minimum shear stresses b. Secondly Maximum and minimum normal stresses c. Both (a) & (b) d. None
Last Answer : b. Secondly Maximum and minimum normal stresses
Description : All the maximum shear stresses are at an angle of (a)45 0 (b) 90 0 (c) 135 0 (d) None
Last Answer : (b) 90 0
Description : Total number of maximum shear stresses is (a) One (b) Three (c) Five (d) None
Last Answer : (b) Three
Description : Maximum shear stress is (a) Average sum of principal stresses (b) Average difference of principal stresses (c) Average sum as well as difference of principal stresses (d) None
Last Answer : (b) Average difference of principal stresses
Description : On the planes of maximum shear, there are (a) Normal stresses (b) Bending stresses (c) Bucking stresses (d) None
Last Answer : (a) Normal stresses
Description : Shear strain energy theory is also known as (a) Coulomb’s theory (b) Distortion energy theory (c) Rankine theory (d) None
Last Answer : (b) Distortion energy theory
Description : The total strain energy for a unit cube subjected to three principal stresses is given by? a) U= [(σέ) 1 + (σέ) 2+ (σέ) 3]/3 b) U= [(σ12+σ22+σ32)/2E] – (σ1σ2+σ2σ3+σ3σ1)2μ c) U= [(σέ) 1 + (σέ) 2+ (σέ) 3]/4 d) None of the mentioned
Last Answer : b) U= [(σ12+σ22+σ32)/2E] – (σ1σ2+σ2σ3+σ3σ1)2μ
Description : Shear strain energy under principal tensile stresses σ1 and σ2 is (a) (1/12E) (σ1 — σ2) 2 + σ2 2 — σ1 2 ) (b) (1/12G) (σ1 — σ2) 2 + σ2 2 + σ1 2 ) (c) (1/12K) (σ1 — σ2) 2 + σ2 2 + σ1 2 ) (d) None
Last Answer : (b) (1/12G) (σ1 — σ2) 2 + σ2 2 + σ1 2 )
Description : The ellipse `x^2+""4y^2=""4` is inscribed in a rectangle aligned with the coordinate axes, which in turn is inscribed in another ellipse that passes t
Last Answer : The ellipse `x^2+""4y^2=""4` is inscribed in a rectangle aligned with the coordinate axes, which in turn is ... 4x^2+48y^2=48` D. `4x^2+64y^2=48`
Description : The bending moment diagram for a cantilever with U.D.L. over the whole span will be (a) Triangle (b) Rectangle (c) Parabola (d) Ellipse
Last Answer : (c) Parabola
Description : Split flywheel is made to (A) Avoid cooling stresses (B) Minimize large centrifugal forces (C) Reduce weight (D) All of the above
Last Answer : (A) Avoid cooling stresses
Description : When comes down to stress reduction, which one is preferred? a) Solid flywheel b) Split flywheel c) Both have equal stresses d) Cannot be determined
Last Answer : b) Split flywheel
Description : Torsional shear stresses are induced in the spring wire when (A) spring is under compression (B) spring is under tension (C) both (A) and (B) (D) none of the above
Last Answer : (C) both (A) and (B)
Description : Propagation of fatigue failure is always due to compressive stresses. a) Due to bending b) Due to tensile c) Due to fatigue d) None of the listed
Last Answer : b) Due to tensile
Description : What will happen if stresses induced due to surge in the spring exceeds the endurance limit stress of the spring. a) Fatigue Failure b) Fracture c) None of the listed d) Nipping
Last Answer : a) Fatigue Failure
Description : If spring index=2.5, what can be concluded about stresses in the wire? a) They are high b) They are negligible c) They are moderate d) Cannot be determined
Last Answer : a) They are high
Description : The helical spring ad wire of helical torsion spring, both are subjected to torsional shear stresses. a) True b) False
Description : Cotter joint is employed when the members are subjected to which sort of stresses? a) Axial tensile b) Axial compressive c) Axial tensile or compressive d) None of the above
Last Answer : c) Axial tensile or compressive
Description : Transverse fillet welds are under (i) Bending and shear stresses (ii)Compressive and torsion shear stresses (iii)Tensile and compressive stresses (iv)None
Last Answer : (iv)None
Description : The advantage of a welded joint over a riveted joint is (i) Introduce residual stresses (ii) Requires highly skilled labor and supervision (iii) Lighter in weight (iv) None
Last Answer : (iii) Lighter in weight
Description : Parallel fillet welds are under Shear and bending stresses Compressive and torsion shear stresses Tensile and compressive stresses None
Last Answer : None
Description : The following bracket is welded to the vertical column. The joint undergoes torsional stresses. a) True b) False
Description : Cotter joint is used when the members are subjected to which type of stresses? a) Axial tensile b) Axial compressive c) Axial tensile or compressive d) None of the mentioned
Description : Which of the following statements are true about eccentrically loaded circular base? a) All bolts are symmetrically spaced with equal angle on either side of vertical b) Bolts are not preloaded c) Bearing is rigid d) Dowel pins are used to relieve stresses
Last Answer : a) All bolts are symmetrically spaced with equal angle on either side of vertical
Description : If the mean stress value for a sinusoidal stress function is zero, then this type of stress falls in which category? a) Fluctuating Stresses b) Alternating Stresses c) Repeated Stresses d) Reversed Stresses
Last Answer : d) Reversed Stresses
Description : The stress represented by cos (t) belongs to which category? a) Fluctuating Stresses b) Alternating Stresses c) Repeated Stresses d) Reversed Stresses
Description : The stress represented by sin (t) + 4 belongs to which category? a) Alternating Stresses b) None of the mentioned c) Repeated Stresses d) Reversed Stresses
Last Answer : a) Alternating Stresses
Description : The stress represented by sin (t) + 2 belongs to which category? a) Fluctuating Stresses b) None of the mentioned c) Repeated Stresses d) Reversed Stresses
Last Answer : a) Fluctuating Stresses
Description : The stress represented by sin (t) + 1 belongs to which category? a) Fluctuating Stresses b) Alternating stresses c) Repeated Stresses d) Reversed Stresses
Last Answer : c) Repeated Stresses