Description : Distortion energy theorem is not recommended for ductile materials. a) True b) False
Last Answer : b) False
Description : The region of safety for biaxial stresses is of which shape in the case of maximum distortion energy theorem. a) Ellipse b) Circle c) Rectangle d) Square
Last Answer : a) Ellipse
Description : In distortion energy theorem, if a unit cube is subjected to biaxial stress, then S(yt) is given by which of the following? a) √ (σ12- σ1σ2 +σ22) b) σ12- σ1σ2 +σ22 c) √ (σ12+ σ1σ2 +σ22) d) σ12+ σ1σ2 +σ22
Last Answer : a) √ (σ12- σ1σ2 +σ22)
Description : Distortion energy theory is slightly liberal as compared to maximum shear stress theory. a) True b) False
Last Answer : a) True
Description : Maximum total strain energy theory is applicable to (a) Ductile materials (b) Brittle materials (c) Composite materials (d) None
Last Answer : (a) Ductile materials
Last Answer : (b) Brittle materials
Description : Theories of elastic failure while dealing with ductile materials consider the failure criterion as (a) Ultimate stress (b) Yield stress (c) Both ultimate and yield stress (d) None
Last Answer : (b) Yield stress
Description : Maximum principal strain theory is applicable to (a) Ductile materials (b) Brittle materials (c) Composite materials (d) None
Description : Maximum shear stress theory is applicable to (a) Ductile materials (b) Brittle materials (c) Composite materials
Description : Maximum principal stress theory is applicable to (a) Ductile materials (b) Brittle materials (c) Composite materials (d) None
Description : Is use of a flywheel recommended when a large motor is required only for a small instant of time? a) True b) False
Description : Multi leaf springs are not recommended for automobile and rail road suspensions. a) True b) False
Description : A ductile material may not meet a failure if it has been tested for the theories of failure (a) Firstly Maximum Shear Stress Theory (b) Secondly Maximum Shear Strain Energy Theory (c) Both (a) & (b) (d) None
Last Answer : (c) Both (a) & (b)
Description : A ductile material may not meet a failure if it has been tested for the theories of failure (a) Firstly Maximum Principal Theory (b) Secondly Maximum Principal Strain Theory (c) Thirdly Maximum principal strain energy theory (d) None
Last Answer : (d) None
Description : Among maximum shear stress theory and distortion energy theory, which gives the higher value shear yield strength? a) Maximum shear stress theory b) Distortion energy theory c) Both give equal values d) Vary from material to material
Last Answer : b) Distortion energy theory
Description : A transmission shaft subjected to pure bending moment should be designed on the basis of (A) Maximum principal stress theory (B) Maximum shear stress theory (C) Distortion energy theory (D) Goodman or Soderberg diagrams
Last Answer : (A) Maximum principal stress theory
Description : Shear strain energy theory is also known as (a) Coulomb’s theory (b) Distortion energy theory (c) Rankine theory (d) None
Last Answer : (b) Distortion energy theory
Description : Maximum Principal Stress Theory is not good for brittle materials. a) True b) False
Description : In the Haig-Soderberg diagram, the test data for ductile material falls near the ______________ a) Soderberg line b) Goodman Line c) Gerber line d) Haig line
Last Answer : c) Gerber line
Description : In which of the following case stress concentration factor is ignored? a) Ductile material under static load b) Ductile material under fluctuating load c) Brittle material under static load
Last Answer : a) Ductile material under static load
Description : In a ductile material, the strength are (a)Firstly Ultimate >yield > elastic limit (b) Secondly Ultimate > yield =elastic limit (c) Thirdly Ultimate=yield=elastic limit (d) None
Last Answer : (a)Firstly Ultimate >yield > elastic limit
Description : Manganese is added in low carbon steel to A. Make the steel tougher and harder B. Raise the yield point C. Make the steel ductile and of good bending qualities D. All of the above
Last Answer : C. Make the steel ductile and of good bending qualities
Description : Which type of threads is recommended for fluctuating loads? a) Fine threads b) Coarse Threads c) Either of fine or coarse d) None of the listed
Last Answer : a) Fine threads
Description : If the lateral force acting on the set screw is large and tends to displace one part with respect to other than which point is recommended? a) Dog Point b) Cone Point c) Window Point d) Cut Point
Last Answer : a) Dog Point
Description : If shaft diameter is 60mm, how many bolts are recommended for rigid flange coupling? a) 2 b) 3 c) 4 d) 5
Last Answer : c) 4
Description : Keyed joints never lead to stress concentration on shafts. a) True b) False
Description : Feather key can be used to prevent axial motion between two elements. a) True b) False
Description : The operation of flywheel is continuous. a) True b) False
Description : Flywheel and governor can be interchanged. a) True b) False
Description : Flywheels are used in punching and shear operation. a) True b) False
Description : The dynamic load-carrying capacity of a bearing is defined as the radial load in radial bearings that can be carried for a minimum life of 1000 revolutions. (a) True (b) False
Last Answer : (b) False
Description : For the majority of bearings, actual life is considerably greater than rated life. (a) True (b) False
Last Answer : (a) True
Description : The life of an individual ball bearing is the time period for which it works without any signs of failures. (a) True (b) False
Description : Stribeck equation gives the dynamic load capacity of the bearing. (a) True (b) False
Description : A total permanent deformation of 0.0001 of the ball diameter is taken for considering the static load capacity of the sh (a) True (b) False
Description : Needles bearing consist of rollers of small diameter and very small length. (a) True (b) False
Description : A cylinder roller creates lesser noise than a deep groove ball bearing. (a) True (b) False
Description : Angular contact bearing can take thrust as well as radial loads. (a) True (b) False
Description : Cylindrical roller bearing has a lower load capacity as compared to deep groove ball bearing. (a) True (b) False
Description : Assertion (A): Hydrostatic lubrication is more advantageous when compared to hydrodynamic lubrication during starting and stopping the journal in its bearing. Reason (R): In hydrodynamic lubrication, the fluid film pressure is ... (c) A is true but R is false (d) A is false but R is true
Last Answer : (b) Both A and R are individually true but R is not the correct explanation of A
Description : Assertion (A): In hydrodynamic journal bearings, the rotating journal is held in floating condition by the hydrodynamic pressure developed in the lubricant. Reason (R): Lubricant flows in a converging-diverging channel. [IES-1994] ... A (c) A is true but R is false (d) A is false but R is true
Last Answer : (a) Both A and R are individually true and R is the correct explanation of A
Description : Assertion (A): Oil as a cutting fluid result in a lower coefficient of friction. Reason (R): Oil forms a thin liquid film between the tool face and chip, and it provides 'hydrodynamic lubrication'. [IES- 2000] (a ... explanation of A (c) A is true but R is false (d) A is false but R is true
Last Answer : (c) A is true but R is false
Description : Assertion (A): In anti-friction bearings, the frictional resistance is very low as the shaft held by it remains in floating condition by the hydrodynamic pressure developed by the lubricant. [IES-2006] Reason (R): In hydrodynamic ... of A (c) A is true but R is false (d) A is false but R is true
Last Answer : (d) A is false but R is true
Description : Assertion (A): In equilibrium position, the journal inside a journal bearing remains floating on the oil film. [IES-1995] Reason (R): In a journal bearing, the load on the bearing is perpendicular to the axis of the ... explanation of A (c) A is true but R is false (d) A is false but R is true
Description : Assertion (A): In steady rotating condition the journal inside a hydrodynamic journal bearing remains floating on the oil film. [IES-2008] Reason (R): The hydrodynamic pressure developed in steady rotating conditions in journal ... A (c) A is true but R is false (d) A is false but R is true
Last Answer : (a) Both A and R are true and R is the correct explanation of A