Description : A transmission shaft subjected to pure bending moment should be designed on the basis of (A) Maximum principal stress theory (B) Maximum shear stress theory (C) Distortion energy theory (D) Goodman or Soderberg diagrams
Last Answer : (A) Maximum principal stress theory
Description : When the shaft is subjected to pure bending moment, the bending stress is given by? a) None of the listed b) 32M/πdɜ c) 16M/πdɜ d) 8M/πdɜ
Last Answer : b) 32M/πdɜ
Description : A transmission shaft subjected to bending loads must be designed on the basis of (a) maximum normal stress theory (b) maximum shear stress theory (c) maximum normal stress and maximum shear stress theories (d) fatigue strength
Last Answer : (a) maximum normal stress theory
Description : The rim of the flywheel is subjected to, 1. direct tensile stress and bending stress 2. torsional shear stress and bending stress 3. direct shear stress and bending stress 4. compressive stress and bending stress
Last Answer : 1. direct tensile stress and bending stress
Description : The rim of the flywheel is subjected to, (A) Direct tensile stress and bending stress (B) Torsional shear stress and bending stress (C) Direct shear stress and bending stress
Last Answer : (A) Direct tensile stress and bending stress
Description : The leaves of multi-leaf springs are subjected to (A) bending stress (B) shear stress (C) axial stress (D) all of the above
Last Answer : (A) bending stress
Description : When the helical torsion spring is subjected to torque, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress
Last Answer : (C) Bending stress
Description : When the helical compression spring is subjected to axial compressive force, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress
Last Answer : (D) Torsional shear stress
Description : When the helical extension spring is subjected to axial tensile force, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress
Description : If a circular shaft is welded to the plate by means of circumferential fillet, then the shaft is subjected to torsional moment M. If throat of weld is t, then torsional shear stress is given by a) M/2πtr2 b) M/πtr2 c) M/4πtr2 d) None of the listed
Last Answer : a) M/2πtr2
Description : The bending moment ‘M’ and a torque ‘T’ is applied on a solid circular shaft. If the maximum bending stress equals to maximum shear stress developed, then ‘M’ is equal to (A) T/2 (B) T (C) 2 T (D) 4 T
Last Answer : (A) T/2
Description : During transverse vibrations, shaft is subjected to which type of stresses? A) Tensile stresses B) Torsional shear stress C) Bending stresses D) All of the above
Last Answer : C) Bending stresses
Description : During transverse vibrations, shaft is subjected to which type of stresses? a. Tensile stresses b. Torsional shear stress c. Bending stresses d. All of the above
Last Answer : c. Bending stresses
Description : A shaft is subjected to bending moment M and a torque T simultaneously. The ratio of the maximum bending stress to maximum shear stress developed in the shaft, is (A) M/T (B) T/M (C) 2M/T (D) 2T/M
Last Answer : (C) 2M/T
Description : shaft subjected to a bending moment M and a torque T, experiences (A) Maximum bending stress = 32M d 3 (B) Maximum shear stress = 16 T d 3 (C) Both (a) and (b) (D) Neither (a) nor (b)
Last Answer : (C) Both (a) and (b)
Description : Torque and bending moment of 100 kN.m and 200 kN.m acts on a shaft which has external diameter twice of internal diameter. What is the external diameter of the shaft which is subjected to a maximum shear stress of 90 N/mm2? a. 116.5 mm b. 233.025 mm c. 587.1 mm d. 900 mm
Last Answer : c. 587.1 mm
Description : What is the maximum shear stress induced in a solid shaft of 50 mm diameter which is subjected to both bending moment and torque of 300 kN.mm and 200 kN.mm respectively? a. 9.11 N/mm2 b. 14.69 N/mm2 c. 16.22 N/mm2 d. 20.98 N/mm2
Last Answer : b. 14.69 N/mm2
Description : The ratio of maximum bending stress to maximum shear stress on the cross section when a shaft is simultaneously subjected to a torque T and bending moment M, a. T/M b. M/T c. 2T/M d. 2M/T
Last Answer : d. 2M/T
Description : A transmission shaft is subjected to bending moment (Mb) and torsional moment (Mt). The equivalent bending moment is given by, (A) √(Mb + Mt) (B) √(Mb2 + Mt2) (C) Mb + Mt (D) Mb +√(Mb2 + Mt2)
Last Answer : (D) Mb +√(Mb2 + Mt2)
Description : A transmission shaft is subjected to bending moment (Mb) and torsional moment (Mt). The equivalent torsional moment is given by, (A) √(Mb + Mt) (B) √(Mb2 + Mt2) (C) Mb + Mt (D) Mb +√(Mb2 + Mt2)
Last Answer : (B) √(Mb2 + Mt2)
Description : Does a plane of maximum shear stress contain a? (a) Normal stress (b) Bending stress (c) Torsional shear stress (d) None
Last Answer : (a) Normal stress
Description : A principal plane is a plane of (a) Only normal stress (b) Only shear stress (c) Only bending stress (d) None
Last Answer : (a) Only normal stress
Description : When the shaft is subjected to pure torsional moment, the torsional stress is given by? a) None of the listed b) 32M/πdɜ c) 16M/πdɜ d) 8M/πdɜ
Last Answer : c) 16M/πdɜ
Description : The spokes of the flywheel are subjected to 1. direct shear stress 2. torsional shear stress 3. tensile stress 4. compressive stress
Last Answer : 3. tensile stress
Description : The spokes of the flywheel are subjected to, (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress
Last Answer : (C) Tensile stress
Description : When a nut is tightened by placing a washer below it, the threads of bolt are subjected to (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress
Last Answer : (A) Direct shear stress
Description : When a nut is tightened by placing a washer below it, the shank of bolt is subjected to (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress
Description : What is the value of shear stress acting on a plane of circular bar which is subjected to axial tensile load of 100 kN? (Diamet a. 58.73 Mpa b. 40.23 Mpa c. 39.60 Mpa d. Insufficient data
Last Answer : c. 39.60 Mpa
Description : Which of the following formulae is used to calculate tangential stress, when a member is subjected to stress in mutually perpendicular axis and accompanied by a shear stress? a. [(σ x - σ y )/2 ]sin θ - τ cos 2θ b. [(σ x - ... τ cos 2θ c. [(σ x - σ y )/2 ]sin θ - τ 2 cos θ d. None of the above
Last Answer : c. [(σ x – σ y )/2 ]sin θ – τ 2 cos θ
Description : Identify the principal stress (a) Shear stress (b) Bending stress (c) Compressive stress (d) None
Last Answer : (c) Compressive stress
Description : The hub is treated as a solid shaft while calculating torsional shear stress in the hub. a) True b) False
Last Answer : b) False
Description : A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and breadth of the key being 14mm and 80mm respectively. Find the shear stress induced in the key. a) 30.2N/mm2 b) 25.8N/mm2 c) 34.4N/mm2 d) None of the listed
Last Answer : b) 25.8N/mm2
Description : On the planes of maximum shear, there are (a) Normal stresses (b) Bending stresses (c) Bucking stresses (d) None
Last Answer : (a) Normal stresses
Description : If a shaft is simultaneously subjected to a toque T and a bending moment M, the ratio of maximum bending stress and maximum shearing stress is (A) M/T (B) T/M (C) 2M/T (D) 2T/M
Description : When the shaft is subjected to pure bending moment, the bending stress is given by? a) None of the listed b) 32M/πdᵌ c) 16M/πdᵌ d) 8M/πdᵌ
Last Answer : b) 32M/πdᵌ
Description : What is the maximum principle stress induced in a solid shaft of 40 mm diameter which is subjected to both bending moment and torque of 300 kN.mm and 150 kN.mm respectively? a. 21.69 N/mm2 b. 28.1 N/mm2 c. 50.57 N/mm2 d. 52.32 N/mm2
Last Answer : c. 50.57 N/mm2
Description : When a body is subjected to transverse vibrations, the stress induced in a body will be A Shear stress B Bending stress C Tensile stress D Compressive stress
Last Answer : B Bending stress
Description : When a body is subjected to transverse vibrations, the stress induced in a body B will be (A) Shear stress (B) Bending stress (C) Tensile stress (D)Compressive stress
Last Answer : (B) Bending stress
Description : When a body is subjected to transverse vibrations, the stress induced in a body will be a) shear stress b) bending stress c) tensile stress d) compressive stress
Last Answer : b) bending stress
Description : When a column is subjected to an eccentric load, the stress induced in the column will be (a) direct stress only (b) bending stress only (c) shear stress only (d) direct and bending stress both
Last Answer : (d) direct and bending stress both
Description : If the strain energy stored per unit volume in a hollow shaft subjected to a pure torque when t attains maximum shear stress fs the ratio of inner diameter to outer diameter, is 17/64 (fs/N) (A) 1/2 (B) 1/3 (C) 1/4 (D) 1/5
Last Answer : (C) 1/4
Description : If a solid shaft (diameter 20 cm, length 400 cm, N = 0.8 × 105 N/mm2 ) when subjected to a twisting moment, produces maximum shear stress of 50 N/mm2 , the angle of twist in radians, is (A) 0.001 (B) 0.002 (C) 0.0025 (D) 0.003
Last Answer : (C) 0.0025
Description : A circular shaft subjected to torsion undergoes a twist of 10in a length of 120 cm. If the maximum shear stress induced is limited to 1000 kg/cm2and if modulus of rigidity G = 0.8 x 106then the radius of the shaft should be (a) p/8 (b) p/27 (c) 18/p (d) 27/p
Last Answer : (d) 27/p
Description : A solid shaft has diameter 80 mm. It is subjected to a torque of 4 KNm. The maximum shear stress induced in the shaft would be (a) 75/p N/mm2 (b) 250/p N/mm2 (c) 125/p N/mm2 (d) 150/p N/mm2
Last Answer : (c) 125/p N/mm2
Description : A hollow prismatic beam of circular section is subjected to a torsional moment. The maximum shear stress occurs at (a) inner wall of cross section (b) middle of thickness (c) outer surface of shaft (d) none of these
Last Answer : (c) outer surface of shaft