The leaves of multi-leaf springs are subjected to (A) bending stress (B) shear stress (C) axial stress (D) all of the above

The leaves of multi-leaf springs are subjected to

(A) bending stress

(B) shear stress

(C) axial stress

(D) all of the above
by

1 Answer

Answer :

(A) bending stress
by

Related questions

When the helical compression spring is subjected to axial compressive force, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress

Description : When the helical compression spring is subjected to axial compressive force, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress

Last Answer : (D) Torsional shear stress

When the helical extension spring is subjected to axial tensile force, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress

Description : When the helical extension spring is subjected to axial tensile force, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress

Last Answer : (D) Torsional shear stress

What is the value of shear stress acting on a plane of circular bar which is subjected to axial tensile load of 100 kN? (Diamet a. 58.73 Mpa b. 40.23 Mpa c. 39.60 Mpa d. Insufficient data

Description : What is the value of shear stress acting on a plane of circular bar which is subjected to axial tensile load of 100 kN? (Diamet a. 58.73 Mpa b. 40.23 Mpa c. 39.60 Mpa d. Insufficient data

Last Answer : c. 39.60 Mpa

The rim of the flywheel is subjected to, 1. direct tensile stress and bending stress 2. torsional shear stress and bending stress 3. direct shear stress and bending stress 4. compressive stress and bending stress

Description : The rim of the flywheel is subjected to, 1. direct tensile stress and bending stress 2. torsional shear stress and bending stress 3. direct shear stress and bending stress 4. compressive stress and bending stress

Last Answer : 1. direct tensile stress and bending stress

The rim of the flywheel is subjected to, (A) Direct tensile stress and bending stress (B) Torsional shear stress and bending stress (C) Direct shear stress and bending stress

Description : The rim of the flywheel is subjected to, (A) Direct tensile stress and bending stress (B) Torsional shear stress and bending stress (C) Direct shear stress and bending stress

Last Answer : (A) Direct tensile stress and bending stress

When the helical torsion spring is subjected to torque, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress

Description : When the helical torsion spring is subjected to torque, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress

Last Answer : (C) Bending stress

A shaft is subjected to the...... A. Normal stress B. Bending stress C. Shear stress D. Combine stress E. All types

Description : A shaft is subjected to the...... A. Normal stress B. Bending stress C. Shear stress D. Combine stress E. All types

Last Answer : E. All types

A transmission shaft subjected to pure bending moment should be designed on the basis of (A) Maximum principal stress theory (B) Maximum shear stress theory (C) Distortion energy theory (D) Goodman or Soderberg diagrams

Description : A transmission shaft subjected to pure bending moment should be designed on the basis of (A) Maximum principal stress theory (B) Maximum shear stress theory (C) Distortion energy theory (D) Goodman or Soderberg diagrams

Last Answer : (A) Maximum principal stress theory

Wahl’s stress concentration factor is used in close coiled springs under axial load to account for (a) Shear effect (b) Bending effect (c) Compression effect (d) none

Description : Wahl’s stress concentration factor is used in close coiled springs under axial load to account for (a) Shear effect (b) Bending effect (c) Compression effect (d) none

Last Answer : (b) Bending effect

Multi-leaf springs are used in (A) automobile suspension (B) railroad suspension (C) both (A) and (B) (D) none of the above

Description : Multi-leaf springs are used in (A) automobile suspension (B) railroad suspension (C) both (A) and (B) (D) none of the above

Last Answer : (C) both (A) and (B)

The type of spring used to achieve greater load carrying capacity within given space is (A) Spiral spring (B) Springs in series (C) Multi-leaf spring (D) Concentric springs

Description : The type of spring used to achieve greater load carrying capacity within given space is (A) Spiral spring (B) Springs in series (C) Multi-leaf spring (D) Concentric springs

Last Answer : (D) Concentric springs

Multi leaf springs are not recommended for automobile and rail road suspensions. a) True b) False

Description : Multi leaf springs are not recommended for automobile and rail road suspensions. a) True b) False

Last Answer : b) False

Ellipse of stress is used to find a. Resultant stress on any plane in a bi-axial stress system b. Resultant stress on any plane in a general two dimensional system c. Maximum shear stress d. Location of planes of maximum shear stress

Description : Ellipse of stress is used to find a. Resultant stress on any plane in a bi-axial stress system b. Resultant stress on any plane in a general two dimensional system c. Maximum shear stress d. Location of planes of maximum shear stress

Last Answer : a. Resultant stress on any plane in a bi-axial stress system

Wahl factor to account for direct shear stress and stress concentration due to curvature for helical springs is given by, (A) (4C - 1/4C - 4) + 0.615/C (B) (4C - 1/4C + 4) + 0.615/C (C) (4C + 1/4C - 4) + 0.615/C (D) (4C + 1/4C + 4) + 0.615/C

Description : Wahl factor to account for direct shear stress and stress concentration due to curvature for helical springs is given by, (A) (4C - 1/4C - 4) + 0.615/C (B) (4C - 1/4C + 4) + 0.615/C (C) (4C + 1/4C - 4) + 0.615/C (D) (4C + 1/4C + 4) + 0.615/C

Last Answer : (A) (4C - 1/4C - 4) + 0.615/C

An arch may be subjected to (A) Shear and axial force (B) Bending moment and shear force (C) Bending moment and axial force (D) Thrust, shear force and bending moment

Description : An arch may be subjected to  (A) Shear and axial force  (B) Bending moment and shear force  (C) Bending moment and axial force  (D) Thrust, shear force and bending moment 

Last Answer : (D) Thrust, shear force and bending moment 

When a close-coiled helical spring is subjected to an axial load, it is said to be under. (a) Bending (b) Shear (c) Torsion (d) Crushing

Description : When a close-coiled helical spring is subjected to an axial load, it is said to be under. (a) Bending (b) Shear (c) Torsion (d) Crushing

Last Answer : (c) Torsion

When the shaft is subjected to pure bending moment, the bending stress is given by? a) None of the listed b) 32M/πdɜ c) 16M/πdɜ d) 8M/πdɜ

Description : When the shaft is subjected to pure bending moment, the bending stress is given by? a) None of the listed b) 32M/πdɜ c) 16M/πdɜ d) 8M/πdɜ

Last Answer : b) 32M/πdɜ

When the shaft is subjected to pure bending moment, the bending stress is given by? a) None of the listed b) 32M/πdɜ c) 16M/πdɜ d) 8M/πdɜ

Description : When the shaft is subjected to pure bending moment, the bending stress is given by? a) None of the listed b) 32M/πdɜ c) 16M/πdɜ d) 8M/πdɜ

Last Answer : b) 32M/πdɜ

The spokes of the flywheel are subjected to 1. direct shear stress 2. torsional shear stress 3. tensile stress 4. compressive stress

Description : The spokes of the flywheel are subjected to 1. direct shear stress 2. torsional shear stress 3. tensile stress 4. compressive stress

Last Answer : 3. tensile stress

The spokes of the flywheel are subjected to, (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress

Description : The spokes of the flywheel are subjected to, (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress

Last Answer : (C) Tensile stress

If a circular shaft is welded to the plate by means of circumferential fillet, then the shaft is subjected to torsional moment M. If throat of weld is t, then torsional shear stress is given by a) M/2πtr2 b) M/πtr2 c) M/4πtr2 d) None of the listed

Description : If a circular shaft is welded to the plate by means of circumferential fillet, then the shaft is subjected to torsional moment M. If throat of weld is t, then torsional shear stress is given by a) M/2πtr2 b) M/πtr2 c) M/4πtr2 d) None of the listed

Last Answer : a) M/2πtr2

When a nut is tightened by placing a washer below it, the threads of bolt are subjected to (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress

Description : When a nut is tightened by placing a washer below it, the threads of bolt are subjected to (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress

Last Answer : (A) Direct shear stress

When a nut is tightened by placing a washer below it, the shank of bolt is subjected to (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress

Description : When a nut is tightened by placing a washer below it, the shank of bolt is subjected to (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress

Last Answer : (C) Tensile stress

Which of the following formulae is used to calculate tangential stress, when a member is subjected to stress in mutually perpendicular axis and accompanied by a shear stress? a. [(σ x – σ y )/2 ]sin θ – τ cos 2θ b. [(σ x – σ y )/2 ]– τ cos 2θ c. [(σ x – σ y )/2 ]sin θ – τ 2 cos θ d. None of the above

Description : Which of the following formulae is used to calculate tangential stress, when a member is subjected to stress in mutually perpendicular axis and accompanied by a shear stress? a. [(σ x - σ y )/2 ]sin θ - τ cos 2θ b. [(σ x - ... τ cos 2θ c. [(σ x - σ y )/2 ]sin θ - τ 2 cos θ d. None of the above

Last Answer : c. [(σ x – σ y )/2 ]sin θ – τ 2 cos θ

Does a plane of maximum shear stress contain a? (a) Normal stress (b) Bending stress (c) Torsional shear stress (d) None

Description : Does a plane of maximum shear stress contain a? (a) Normal stress (b) Bending stress (c) Torsional shear stress (d) None

Last Answer : (a) Normal stress

Identify the principal stress (a) Shear stress (b) Bending stress (c) Compressive stress (d) None

Description : Identify the principal stress (a) Shear stress (b) Bending stress (c) Compressive stress (d) None

Last Answer : (c) Compressive stress

A principal plane is a plane of (a) Only normal stress (b) Only shear stress (c) Only bending stress (d) None

Description : A principal plane is a plane of (a) Only normal stress (b) Only shear stress (c) Only bending stress (d) None

Last Answer : (a) Only normal stress

The bending moment ‘M’ and a torque ‘T’ is applied on a solid circular shaft. If the maximum bending stress equals to maximum shear stress developed, then ‘M’ is equal to (A) T/2 (B) T (C) 2 T (D) 4 T

Description : The bending moment ‘M’ and a torque ‘T’ is applied on a solid circular shaft. If the maximum bending stress equals to maximum shear stress developed, then ‘M’ is equal to (A) T/2 (B) T (C) 2 T (D) 4 T

Last Answer : (A) T/2

When two concentric springs are made of same material, having same free length and compressed equally by axial load, then the load shared by each spring is proportional to (A) Spring index of each spring (B) Wire diameter of each spring (C) Mean coil diameter of each spring (D) Square of wire diameter of each spring

Description : When two concentric springs are made of same material, having same free length and compressed equally by axial load, then the load shared by each spring is proportional to (A) Spring index of each spring ... spring (C) Mean coil diameter of each spring (D) Square of wire diameter of each spring

Last Answer : (D) Square of wire diameter of each spring

A diagram which shows the variations of the axial load for all sections of the span of a beam, is called (A) Bending moment diagram (B) Shear force diagram (C) Thrust diagram (D) Stress diagram

Description : A diagram which shows the variations of the axial load for all sections of the span of a beam, is called (A) Bending moment diagram (B) Shear force diagram (C) Thrust diagram (D) Stress diagram

Last Answer : Answer: Option C

The graphical representation of variation of axial load on y axis and position of cross section along x axis is called as _____ (a) Bending moment diagram (b) Shear force diagram (c) Stress-strain diagram (d) Trust diagram

Description : The graphical representation of variation of axial load on y axis and position of cross section along x axis is called as _____ (a) Bending moment diagram (b) Shear force diagram (c) Stress-strain diagram (d) Trust diagram

Last Answer : (d) Trust diagram

Cotter joint is employed when the members are subjected to which sort of stresses? a) Axial tensile b) Axial compressive c) Axial tensile or compressive d) None of the above

Description : Cotter joint is employed when the members are subjected to which sort of stresses? a) Axial tensile b) Axial compressive c) Axial tensile or compressive d) None of the above

Last Answer : c) Axial tensile or compressive

Cotter joint is used when the members are subjected to which type of stresses? a) Axial tensile b) Axial compressive c) Axial tensile or compressive d) None of the mentioned

Description : Cotter joint is used when the members are subjected to which type of stresses? a) Axial tensile b) Axial compressive c) Axial tensile or compressive d) None of the mentioned

Last Answer : c) Axial tensile or compressive

When a body is subjected to transverse vibrations, the stress induced in a body will be A Shear stress B Bending stress C Tensile stress D Compressive stress

Description : When a body is subjected to transverse vibrations, the stress induced in a body will be A Shear stress B Bending stress C Tensile stress D Compressive stress

Last Answer : B Bending stress

During transverse vibrations, shaft is subjected to which type of stresses? A) Tensile stresses B) Torsional shear stress C) Bending stresses D) All of the above

Description : During transverse vibrations, shaft is subjected to which type of stresses? A) Tensile stresses B) Torsional shear stress C) Bending stresses D) All of the above

Last Answer : C) Bending stresses

When a body is subjected to transverse vibrations, the stress induced in a body B will be (A) Shear stress (B) Bending stress (C) Tensile stress (D)Compressive stress

Description : When a body is subjected to transverse vibrations, the stress induced in a body B will be (A) Shear stress (B) Bending stress (C) Tensile stress (D)Compressive stress

Last Answer : (B) Bending stress

When a body is subjected to transverse vibrations, the stress induced in a body will be a) shear stress b) bending stress c) tensile stress d) compressive stress

Description : When a body is subjected to transverse vibrations, the stress induced in a body will be a) shear stress b) bending stress c) tensile stress d) compressive stress

Last Answer : b) bending stress

During transverse vibrations, shaft is subjected to which type of stresses? a. Tensile stresses b. Torsional shear stress c. Bending stresses d. All of the above

Description : During transverse vibrations, shaft is subjected to which type of stresses? a. Tensile stresses b. Torsional shear stress c. Bending stresses d. All of the above

Last Answer : c. Bending stresses

When a body is subjected to transverse vibrations, the stress induced in a body will be a) shear stress b) bending stress c) tensile stress d) compressive stress

Description : When a body is subjected to transverse vibrations, the stress induced in a body will be a) shear stress b) bending stress c) tensile stress d) compressive stress

Last Answer : b) bending stress

A shaft is subjected to bending moment M and a torque T simultaneously. The ratio of the maximum bending stress to maximum shear stress developed in the shaft, is (A) M/T (B) T/M (C) 2M/T (D) 2T/M

Description : A shaft is subjected to bending moment M and a torque T simultaneously. The ratio of the  maximum bending stress to maximum shear stress developed in the shaft, is  (A) M/T (B) T/M (C) 2M/T (D) 2T/M

Last Answer : (C) 2M/T

shaft subjected to a bending moment M and a torque T, experiences (A) Maximum bending stress = 32M d 3 (B) Maximum shear stress = 16 T d 3 (C) Both (a) and (b) (D) Neither (a) nor (b)

Description :  shaft subjected to a bending moment M and a torque T, experiences  (A) Maximum bending stress = 32M d 3 (B) Maximum shear stress = 16 T d 3 (C) Both (a) and (b)  (D) Neither (a) nor (b)

Last Answer : (C) Both (a) and (b) 

When a column is subjected to an eccentric load, the stress induced in the column will be (a) direct stress only (b) bending stress only (c) shear stress only (d) direct and bending stress both

Description : When a column is subjected to an eccentric load, the stress induced in the column will be (a) direct stress only (b) bending stress only (c) shear stress only (d) direct and bending stress both

Last Answer : (d) direct and bending stress both

A transmission shaft subjected to bending loads must be designed on the basis of (a) maximum normal stress theory (b) maximum shear stress theory (c) maximum normal stress and maximum shear stress theories (d) fatigue strength

Description : A transmission shaft subjected to bending loads must be designed on the basis of (a) maximum normal stress theory (b) maximum shear stress theory (c) maximum normal stress and maximum shear stress theories (d) fatigue strength

Last Answer : (a) maximum normal stress theory

Torque and bending moment of 100 kN.m and 200 kN.m acts on a shaft which has external diameter twice of internal diameter. What is the external diameter of the shaft which is subjected to a maximum shear stress of 90 N/mm2? a. 116.5 mm b. 233.025 mm c. 587.1 mm d. 900 mm

Description : Torque and bending moment of 100 kN.m and 200 kN.m acts on a shaft which has external diameter twice of internal diameter. What is the external diameter of the shaft which is subjected to a maximum shear stress of 90 N/mm2? a. 116.5 mm b. 233.025 mm c. 587.1 mm d. 900 mm

Last Answer : c. 587.1 mm

What is the maximum shear stress induced in a solid shaft of 50 mm diameter which is subjected to both bending moment and torque of 300 kN.mm and 200 kN.mm respectively? a. 9.11 N/mm2 b. 14.69 N/mm2 c. 16.22 N/mm2 d. 20.98 N/mm2

Description : What is the maximum shear stress induced in a solid shaft of 50 mm diameter which is subjected to both bending moment and torque of 300 kN.mm and 200 kN.mm respectively? a. 9.11 N/mm2 b. 14.69 N/mm2 c. 16.22 N/mm2 d. 20.98 N/mm2

Last Answer : b. 14.69 N/mm2

The ratio of maximum bending stress to maximum shear stress on the cross section when a shaft is simultaneously subjected to a torque T and bending moment M, a. T/M b. M/T c. 2T/M d. 2M/T

Description : The ratio of maximum bending stress to maximum shear stress on the cross section when a shaft is simultaneously subjected to a torque T and bending moment M, a. T/M b. M/T c. 2T/M d. 2M/T

Last Answer : d. 2M/T

Footstep bearing is an axial load bearing. a) True b) Thrust load c) Shear load d) None of the listed

Description : Footstep bearing is an axial load bearing. a) True b) Thrust load c) Shear load d) None of the listed

Last Answer : b) Thrust load

For finding out the bending moment for the arm (spoke) of flywheel the arm is assumed as 1. a cantilever beam fixed at the rim and subjected to tangential force at the hub 2. a simply supported beam fixed at hub and rim and carrying uniformly distributed load 3. a cantilever hub fixed at the rim and subjected to tangential force at the rim 4. a fixed beam fixed at hub and rim and carrying uniformly distributed load

Description : For finding out the bending moment for the arm (spoke) of flywheel the arm is assumed as 1. a cantilever beam fixed at the rim and subjected to tangential force at the hub 2. a simply ... tangential force at the rim 4. a fixed beam fixed at hub and rim and carrying uniformly distributed load

Last Answer : 3. a cantilever hub fixed at the rim and subjected to tangential force at the rim

For finding out the bending moment for the arm (spoke) of flywheel, the arm is assumed as, (A) A cantilever beam fixed at the rim and subjected to tangential force at the hub (B) A simply supported beam fixed at hub and rim and carrying uniformly distributed load (C) A cantilever beam fixed at the hub and subjected to tangential force at the rim (D) A fixed beam fixed at hub and rim and carrying uniformly distributed load

Description : For finding out the bending moment for the arm (spoke) of flywheel, the arm is assumed as, (A) A cantilever beam fixed at the rim and subjected to tangential force at the hub (B) A simply ... tangential force at the rim (D) A fixed beam fixed at hub and rim and carrying uniformly distributed load

Last Answer : (C) A cantilever beam fixed at the hub and subjected to tangential force at the rim

The strip of spiral spring is never subjected to pure bending moment. a) True b) False

Description : The strip of spiral spring is never subjected to pure bending moment. a) True b) False

Last Answer : b) False