While designing shaft on the basis of torsional rigidity, angle of twist is given by? a) Ml/Gd4 b) 584Ml/Gd4 c) 292 Ml/Gd4 d) None of the mentioned

While designing shaft on the basis of torsional rigidity, angle of twist is given by?

a) Ml/Gd4

b) 584Ml/Gd4

c) 292 Ml/Gd4

d) None of the mentioned
by

1 Answer

Answer :

b) 584Ml/Gd4
by

Related questions

While designing shaft on the basis of torsional rigidity, angle of twist is given by? a) Ml/Gd4 b) 584Ml/Gd4 c) 292 Ml/Gd4 d) None of the mentioned

Description : While designing shaft on the basis of torsional rigidity, angle of twist is given by? a) Ml/Gd4 b) 584Ml/Gd4 c) 292 Ml/Gd4 d) None of the mentioned

Last Answer : b) 584Ml/Gd4

While designing shaft on the basis of torsional rigidity, angle of twist is given by? a) 100Ml/Gd⁴ b) 584Ml/Gd⁴ c) 292 Ml/Gd⁴ d) 300 Ml/Gd⁴

Description : While designing shaft on the basis of torsional rigidity, angle of twist is given by? a) 100Ml/Gd⁴ b) 584Ml/Gd⁴ c) 292 Ml/Gd⁴ d) 300 Ml/Gd⁴

Last Answer : b) 584Ml/Gd⁴

Calculate the shaft diameter on rigidity basis if torsional moment is 196000N-mm, length of shaft is 1000mm. Permissible angle of twist per meter is 0.5’ and take G=79300N/mm2. a) None of the listed b) 41.2mm c) 35.8mm d) 38.8mm

Description : Calculate the shaft diameter on rigidity basis if torsional moment is 196000N-mm, length of shaft is 1000mm. Permissible angle of twist per meter is 0.5’ and take G=79300N/mm2. a) None of the listed b) 41.2mm c) 35.8mm d) 38.8mm

Last Answer : b) 41.2mm

The shafts will have same strength on the basis of torsional rigidity, if (A) Diameter and length of both shafts is same (B) Material of both shafts is same (C) Angle of twist for both shafts is same (D) All of above conditions are satisfied

Description : The shafts will have same strength on the basis of torsional rigidity, if (A) Diameter and length of both shafts is same (B) Material of both shafts is same (C) Angle of twist for both shafts is same (D) All of above conditions are satisfied

Last Answer : (D) All of above conditions are satisfied

Calculate the shaft diameter on rigidity basis if torsional moment is 196000N-mm, length of shaft is 1000mm. Permissible angle of twist per meter is 0.5’ and take G=79300N/mm². a) None of the listed b) 41.2mm c) 35.8mm d) 38.8mm

Description : Calculate the shaft diameter on rigidity basis if torsional moment is 196000N-mm, length of shaft is 1000mm. Permissible angle of twist per meter is 0.5’ and take G=79300N/mm². a) None of the listed b) 41.2mm c) 35.8mm d) 38.8mm

Last Answer : b) 41.2mm

The angle of twist for the equivalent bar to a spring is given by? (Symbols have their usual meaning) a) 8PD2N/Gd4 b) 16PD2N/Gd4 c) 16PDN/Gdɜ d) 8PDN/Gdɜ

Description : The angle of twist for the equivalent bar to a spring is given by? (Symbols have their usual meaning) a) 8PD2N/Gd4 b) 16PD2N/Gd4 c) 16PDN/Gdɜ d) 8PDN/Gdɜ

Last Answer : b) 16PD2N/Gd4

Pick up the incorrect statement from the following: The torsional resistance of a shaft is directly proportional to (A) Modulus of rigidity (B) Angle of twist (C) Reciprocal of the length of the shaft (D) Moment of inertia of the shaft section

Description : Pick up the incorrect statement from the following: The torsional resistance of a shaft is directly  proportional to  (A) Modulus of rigidity  (B) Angle of twist  (C) Reciprocal of the length of the shaft  (D) Moment of inertia of the shaft section 

Last Answer : (D) Moment of inertia of the shaft section 

The shafts will have same strength on the basis of torsional rigidity, if (a) diameter and length of both shafts is same (b) material of both shafts is same (c) angle of twist for both shafts is same (d) all of above conditions are satisfied

Description : The shafts will have same strength on the basis of torsional rigidity, if (a) diameter and length of both shafts is same (b) material of both shafts is same (c) angle of twist for both shafts is same (d) all of above conditions are satisfied

Last Answer : (d) all of above conditions are satisfied

The axial deflection of spring for the small angle of θ is given by? a) 328PDɜN/Gd4 b) 8PDɜN/Gd4 c) 16PDɜN/Gd4 d) 8PD2N/Gdɜ

Description : The axial deflection of spring for the small angle of θ is given by? a) 328PDɜN/Gd4 b) 8PDɜN/Gd4 c) 16PDɜN/Gd4 d) 8PD2N/Gdɜ

Last Answer : b) 8PDɜN/Gd4

The angle of twist for a transmission shaft is inversely proportional to (A) Shaft diameter (B) (Shaft diameter)2 (C) (Shaft diameter)3 (D) (Shaft diameter)4

Description : The angle of twist for a transmission shaft is inversely proportional to (A) Shaft diameter (B) (Shaft diameter)2 (C) (Shaft diameter)3 (D) (Shaft diameter)4

Last Answer : (D) (Shaft diameter)4

In a shaft, the shear stress is not directly proportional to (A) Radius of the shaft (B) Angle of twist (C) Length of the shaft (D) Modulus of rigidity

Description : In a shaft, the shear stress is not directly proportional to  (A) Radius of the shaft  (B) Angle of twist  (C) Length of the shaft  (D) Modulus of rigidity

Last Answer : (C) Length of the shaft

A hollow shaft of 1 m length is designed to transmit a power of 30 kW at 700 rpm. The maximum permissible angle of twist in the shaft is 1o. The inner diameter of the shaft is 0.7 times the outer diameter. The modulus of rigidity is 80 GPa. The outside diameter (in mm) of the shaft is _______. (a) 43 to 45 (b) 50to 60 (c) 70 to 80 (d) 85 to 100

Description : A hollow shaft of 1 m length is designed to transmit a power of 30 kW at 700 rpm. The maximum permissible angle of twist in the shaft is 1o. The inner diameter of the shaft is 0.7 times the outer diameter. The modulus of ... shaft is _______. (a) 43 to 45 (b) 50to 60 (c) 70 to 80 (d) 85 to 100

Last Answer : (a) 43 to 45

For two shafts joined in parallel, the --------------- in each shaft is same. a. shear stress. b. Angle of twist c. torque d. torsional stress.

Description : For two shafts joined in parallel, the --------------- in each shaft is same. a. shear stress. b. Angle of twist c. torque d. torsional stress.

Last Answer : b. Angle of twist

For two shafts joined in series, the --------------- in each shaft is same. a. shear stress. b. Angle of twist c. torque d. torsional stress.

Description : For two shafts joined in series, the --------------- in each shaft is same. a. shear stress. b. Angle of twist c. torque d. torsional stress.

Last Answer : c. torque

While designing screw threads, adequate length of engaged threads between the screw and nut is provided so as to prevent failure of threads due to (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress

Description : While designing screw threads, adequate length of engaged threads between the screw and nut is provided so as to prevent failure of threads due to (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress

Last Answer : (A) Direct shear stress

The hub is treated as a solid shaft while calculating torsional shear stress in the hub. a) True b) False

Description : The hub is treated as a solid shaft while calculating torsional shear stress in the hub. a) True b) False

Last Answer : b) False

The hub is treated as a solid shaft while calculating torsional shear stress in the hub. a) True b) False

Description : The hub is treated as a solid shaft while calculating torsional shear stress in the hub. a) True b) False

Last Answer : b) False

If a circular shaft is welded to the plate by means of circumferential fillet, then the shaft is subjected to torsional moment M. If throat of weld is t, then torsional shear stress is given by a) M/2πtr2 b) M/πtr2 c) M/4πtr2 d) None of the listed

Description : If a circular shaft is welded to the plate by means of circumferential fillet, then the shaft is subjected to torsional moment M. If throat of weld is t, then torsional shear stress is given by a) M/2πtr2 b) M/πtr2 c) M/4πtr2 d) None of the listed

Last Answer : a) M/2πtr2

When the shaft is subjected to pure torsional moment, the torsional stress is given by? a) None of the listed b) 32M/πdɜ c) 16M/πdɜ d) 8M/πdɜ

Description : When the shaft is subjected to pure torsional moment, the torsional stress is given by? a) None of the listed b) 32M/πdɜ c) 16M/πdɜ d) 8M/πdɜ

Last Answer : c) 16M/πdɜ

When the shaft is subjected to pure torsional moment, the torsional stress is given by? a) None of the listed b) 32M/πdɜ c) 16M/πdɜ d) 8M/πdɜ

Description : When the shaft is subjected to pure torsional moment, the torsional stress is given by? a) None of the listed b) 32M/πdɜ c) 16M/πdɜ d) 8M/πdɜ

Last Answer : c) 16M/πdɜ

A transmission shaft is subjected to bending moment (Mb) and torsional moment (Mt). The equivalent bending moment is given by, (A) √(Mb + Mt) (B) √(Mb2 + Mt2) (C) Mb + Mt (D) Mb +√(Mb2 + Mt2)

Description : A transmission shaft is subjected to bending moment (Mb) and torsional moment (Mt). The equivalent bending moment is given by, (A) √(Mb + Mt) (B) √(Mb2 + Mt2) (C) Mb + Mt (D) Mb +√(Mb2 + Mt2)

Last Answer : (D) Mb +√(Mb2 + Mt2)

A transmission shaft is subjected to bending moment (Mb) and torsional moment (Mt). The equivalent torsional moment is given by, (A) √(Mb + Mt) (B) √(Mb2 + Mt2) (C) Mb + Mt (D) Mb +√(Mb2 + Mt2)

Description : A transmission shaft is subjected to bending moment (Mb) and torsional moment (Mt). The equivalent torsional moment is given by, (A) √(Mb + Mt) (B) √(Mb2 + Mt2) (C) Mb + Mt (D) Mb +√(Mb2 + Mt2)

Last Answer : (B) √(Mb2 + Mt2)

While designing a flange coupling, care is taken so that (A) Shaft is the weakest component (B) Bolts are the weakest component (C) Key is the weakest component (D) The flange is the weakest component

Description : While designing a flange coupling, care is taken so that (A) Shaft is the weakest component (B) Bolts are the weakest component (C) Key is the weakest component (D) The flange is the weakest component

Last Answer : (C) Key is the weakest component

Torsional rigidity of a shaft is given by a. Gl/θ b. Tθ c. Tl/θ d. T/l

Description : Torsional rigidity of a shaft is given by a. Gl/θ b. Tθ c. Tl/θ d. T/l

Last Answer : c. Tl/θ

A circular shaft subjected to torsion undergoes a twist of 10in a length of 120 cm. If the maximum shear stress induced is limited to 1000 kg/cm2and if modulus of rigidity G = 0.8 x 106then the radius of the shaft should be (a) p/8 (b) p/27 (c) 18/p (d) 27/p

Description : A circular shaft subjected to torsion undergoes a twist of 10in a length of 120 cm. If the maximum shear stress induced is limited to 1000 kg/cm2and if modulus of rigidity G = 0.8 x 106then the radius of the shaft should be (a) p/8 (b) p/27 (c) 18/p (d) 27/p

Last Answer : (d) 27/p

The keyway, (A) Reduces strength of shaft (B) Reduces rigidity of shaft (C) Increases stress concentration (D) All of above

Description : The keyway, (A) Reduces strength of shaft (B) Reduces rigidity of shaft (C) Increases stress concentration (D) All of above

Last Answer : (D) All of above

Which of the following relation is correct regarding free torsional vibrations of a single motor system? a) Independent of modulus of rigidity b) Independent of polar moment of inertia c) Dependent on mass moment of inertia d) Independent of length of shaft

Description : Which of the following relation is correct regarding free torsional vibrations of a single motor system? a) Independent of modulus of rigidity b) Independent of polar moment of inertia c) Dependent on mass moment of inertia d) Independent of length of shaft

Last Answer : c) Dependent on mass moment of inertia

The product of the tangential force acting on the shaft and radius of shaft known as (a) Torsional rigidity (b) Flexural rigidity (c) Bending moment (d) Twisting moment

Description : The product of the tangential force acting on the shaft and radius of shaft known as (a) Torsional rigidity (b) Flexural rigidity (c) Bending moment (d) Twisting moment

Last Answer : (d) Twisting moment

Strength of a shaft a. Is equal to maximum shear stress in the shaft at the time of elastic failure b. Is equal to maximum shear stress in the shaft at the time of rupture c. Is equal to torsional rigidity d. Is ability to resist maximum twisting moment

Description : Strength of a shaft a. Is equal to maximum shear stress in the shaft at the time of elastic failure b. Is equal to maximum shear stress in the shaft at the time of rupture c. Is equal to torsional rigidity d. Is ability to resist maximum twisting moment

Last Answer : d. Is ability to resist maximum twisting moment

Torsional rigidity of a shaft is defined as a. G/J b. GJ c. TJ d. T/J

Description : Torsional rigidity of a shaft is defined as a. G/J b. GJ c. TJ d. T/J

Last Answer : a. G/J

In designing a flange coupling, the pitch circle diameter of bolts is taken as (where d = Diameter of the shaft) (A) 2 d (B) 3 d (C) 4 d (D) 5 d

Description : In designing a flange coupling, the pitch circle diameter of bolts is taken as (where d = Diameter of the shaft) (A) 2 d (B) 3 d (C) 4 d (D) 5 d

Last Answer : (B) 3 d

Which of the following act on shafts? a) Torsional moment b) Bending Moment c) Both torsional and bending d) None of the mentioned

Description : Which of the following act on shafts? a) Torsional moment b) Bending Moment c) Both torsional and bending d) None of the mentioned

Last Answer : c) Both torsional and bending

Which of the following act on shafts? a) Torsional moment b) Bending Moment c) Both torsional and bending d) None of the mentioned

Description : Which of the following act on shafts? a) Torsional moment b) Bending Moment c) Both torsional and bending d) None of the mentioned

Last Answer : c) Both torsional and bending

Angle of twist of a circular shaft is given by a. GJ/Tl b. Tl/GJ. c. TJ/Gl. d.TG/Jl.

Description : Angle of twist of a circular shaft is given by a. GJ/Tl b. Tl/GJ. c. TJ/Gl. d.TG/Jl.

Last Answer : b. Tl/GJ.

Angle of rotation o arbour with respect to drum is given by? a) None of the listed b) 12ML/Ebtɜ c) 8 ML/Ebtɜ d) 16ML/Ebtɜ

Description : Angle of rotation o arbour with respect to drum is given by? a) None of the listed b) 12ML/Ebtɜ c) 8 ML/Ebtɜ d) 16ML/Ebtɜ

Last Answer : b) 12ML/Ebtɜ

A transmission shaft subjected to pure bending moment should be designed on the basis of (A) Maximum principal stress theory (B) Maximum shear stress theory (C) Distortion energy theory (D) Goodman or Soderberg diagrams

Description : A transmission shaft subjected to pure bending moment should be designed on the basis of (A) Maximum principal stress theory (B) Maximum shear stress theory (C) Distortion energy theory (D) Goodman or Soderberg diagrams

Last Answer : (A) Maximum principal stress theory

If a solid shaft (diameter 20 cm, length 400 cm, N = 0.8 × 105 N/mm2 ) when subjected to a twisting moment, produces maximum shear stress of 50 N/mm2 , the angle of twist in radians, is (A) 0.001 (B) 0.002 (C) 0.0025 (D) 0.003

Description : If a solid shaft (diameter 20 cm, length 400 cm, N = 0.8 × 105  N/mm2 ) when subjected to a twisting  moment, produces maximum shear stress of 50 N/mm2 , the angle of twist in radians, is  (A) 0.001  (B) 0.002  (C) 0.0025  (D) 0.003 

Last Answer : (C) 0.0025 

The angle of twist for a transmission shaft is inversely proportional to (a) shaft diameter (b) (shaft diameter)2 (c) (shaft diameter)3 (d) (shaft diameter)4

Description : The angle of twist for a transmission shaft is inversely proportional to (a) shaft diameter (b) (shaft diameter)2 (c) (shaft diameter)3 (d) (shaft diameter)4

Last Answer : (a) shaft diameter

A shaft of length L is subject to a constant twisting moment T along its length L, then angle q through which one end of the bar will twist relative to other will be (a) T/g (b) T/GJ (c) GJ/TL (d) TL/GJ

Description : A shaft of length L is subject to a constant twisting moment T along its length L, then angle q through which one end of the bar will twist relative to other will be (a) T/g (b) T/GJ (c) GJ/TL (d) TL/GJ

Last Answer : (d) TL/GJ

Which of the following is not an assumption in derivation of torsion equation? a. Circular shaft remains circular after twisting b. Plane section of the shaft remain plane after twisting c. Material of shaft is isotropic d. Angle of twist is proportional to radius

Description : Which of the following is not an assumption in derivation of torsion equation? a. Circular shaft remains circular after twisting b. Plane section of the shaft remain plane after twisting c. Material of shaft is isotropic d. Angle of twist is proportional to radius

Last Answer : d. Angle of twist is proportional to radius

Two shafts in torsion will have equal strength if a. Only diameter of the shafts is same b. Only angle of twist of the shaft is same c. Only material of the shaft is same d. Only torque transmitting capacity of the shaft is same

Description : Two shafts in torsion will have equal strength if a. Only diameter of the shafts is same b. Only angle of twist of the shaft is same c. Only material of the shaft is same d. Only torque transmitting capacity of the shaft is same

Last Answer : d. Only torque transmitting capacity of the shaft is same

While designing a forging, the profile is selected such that the fibrous lines are parallel to the tensile forces and perpendicular to shear forces. a) True b) False

Description : While designing a forging, the profile is selected such that the fibrous lines are parallel to the tensile forces and perpendicular to shear forces. a) True b) False

Last Answer : a) True

The rolling contact bearings as compared to sliding contact bearings have (a) small overall dimensions (b) accuracy of shaft alignment (c) low starting and low running friction except at very high speeds (d) all the mentioned

Description : The rolling contact bearings as compared to sliding contact bearings have (a) small overall dimensions (b) accuracy of shaft alignment (c) low starting and low running friction except at very high speeds (d) all the mentioned

Last Answer : (d) all the mentioned

The critical speed of a shaft with a disc supported in between is equal to the natural frequency of the system in A Transverse vibrations B Torsional vibrations C Longitudinal vibrations D None of the mentioned

Description : The critical speed of a shaft with a disc supported in between is equal to the natural frequency of the system in A Transverse vibrations B Torsional vibrations C Longitudinal vibrations D None of the mentioned

Last Answer : A Transverse vibrations

The vibrations perpendicular to the shaft axis are known as A Transverse B Longitudinal C Torsional D None of the mentioned

Description : The vibrations perpendicular to the shaft axis are known as A Transverse B Longitudinal C Torsional D None of the mentioned

Last Answer : A Transverse

The critical speed of a shaft with a disc supported in between is equal to the natural frequency of the system in a) transverse vibrations b) torsional vibrations c) longitudinal vibrations d) none of the mentioned

Description : The critical speed of a shaft with a disc supported in between is equal to the natural frequency of the system in a) transverse vibrations b) torsional vibrations c) longitudinal vibrations d) none of the mentioned

Last Answer : a) transverse vibrations

The critical speed of a shaft with a disc supported in between is equal to the natural frequency of the system in a) transverse vibrations b) torsional vibrations c) longitudinal vibrations d) none of the mentioned

Description : The critical speed of a shaft with a disc supported in between is equal to the natural frequency of the system in a) transverse vibrations b) torsional vibrations c) longitudinal vibrations d) none of the mentioned

Last Answer : a) transverse vibrations

Which of the following isn’t the property of a taper roller bearing? (a) High rigidity (b) Easy dismantling (c) Take low radial and heavy loads (d) It is unsuitable for high speed applications

Description : Which of the following isn’t the property of a taper roller bearing? (a) High rigidity (b) Easy dismantling (c) Take low radial and heavy loads (d) It is unsuitable for high speed applications

Last Answer : (c) Take low radial and heavy loads

The deep groove ball bearing has immense rigidity. (a) True (b) No, it has point contact and hence low rigidity (c) It has surface contact (d) It has line contact

Description : The deep groove ball bearing has immense rigidity. (a) True (b) No, it has point contact and hence low rigidity (c) It has surface contact (d) It has line contact

Last Answer : (b) No, it has point contact and hence low rigidity

If fluid film pressure is high and surface rigidity is low than mode of lubrication is called as elastohydrodynamic lubrication. a) True b) False

Description : If fluid film pressure is high and surface rigidity is low than mode of lubrication is called as elastohydrodynamic lubrication. a) True b) False

Last Answer : a) True