The rolling contact bearings as compared to sliding contact bearings have (a) small overall dimensions (b) accuracy of shaft alignment (c) low starting and low running friction except at very high speeds (d) all the mentioned

The rolling contact bearings as compared to sliding contact bearings have

(a) small overall dimensions

(b) accuracy of shaft alignment

(c) low starting and low running friction except at very high speeds

(d) all the mentioned
by

1 Answer

Answer :

(d) all the mentioned
by

Related questions

The antifriction bearings (a) have low starting and low running friction at moderate speeds (b) have a high initial cost (c) can carry both radial and thrust loads (d) all the mentioned

Description : The antifriction bearings (a) have low starting and low running friction at moderate speeds (b) have a high initial cost (c) can carry both radial and thrust loads (d) all the mentioned

Last Answer : (d) all the mentioned

. In gear boxes and small size motors, rolling contact bearings are used. a) True b) False

Description : . In gear boxes and small size motors, rolling contact bearings are used. a) True b) False

Last Answer : a) True

It is easier to roll a barrel than to pull it because (a) the full weight of the barrel comes into play when it is pulled (b) rolling friction is much less than sliding friction (c) the surface area of the barrel in contact with the road is more in the case of pulling (d) of a reason other than those mentioned

Description : It is easier to roll a barrel than to pull it because (a) the full weight of the barrel comes into play when it is pulled (b) rolling friction is much less than sliding friction (c) the surface ... in contact with the road is more in the case of pulling (d) of a reason other than those mentioned

Last Answer : Ans:(b)

In sliding contact bearings, a positive pressure can be built up and a load supported by a fluid only by the use of a: [IES-2005] (a) Diverging film (b) Converging-diverging film (c) Converging film (d) Flat film

Description : In sliding contact bearings, a positive pressure can be built up and a load supported by a fluid only by the use of a: [IES-2005] (a) Diverging film (b) Converging-diverging film (c) Converging film (d) Flat film

Last Answer : (c) Converging film

Sliding contact bearings, also called plain bearings have no problem of wear. a) True b) False

Description : Sliding contact bearings, also called plain bearings have no problem of wear. a) True b) False

Last Answer : b) False

A journal bearing is a ______ contact bearing working on the hydrodynamic lubrication and which supports load in____ direction. a) Sliding, Axial b) Rolling, Radial c) Sliding, Radial d) Rolling, Axial

Description : A journal bearing is a ______ contact bearing working on the hydrodynamic lubrication and which supports load in____ direction. a) Sliding, Axial b) Rolling, Radial c) Sliding, Radial d) Rolling, Axial

Last Answer : c) Sliding, Radial

Which of the following are functions of bearings? a) Ensure free rotation of shaft with minimum friction b) Holding shaft in a correct position c) Transmit the force of the shaft to the frame d) All of the listed

Description : Which of the following are functions of bearings? a) Ensure free rotation of shaft with minimum friction b) Holding shaft in a correct position c) Transmit the force of the shaft to the frame d) All of the listed

Last Answer : d) All of the listed

The rolling contact bearings are known as (a) thick lubricated bearings (b) plastic bearings (c) thin lubricated bearings (d) antifriction bearings

Description : The rolling contact bearings are known as (a) thick lubricated bearings (b) plastic bearings (c) thin lubricated bearings (d) antifriction bearings

Last Answer : (d) antifriction bearings

In steam and gas turbines, rolling contact bearings are used. a) True b) False

Description : In steam and gas turbines, rolling contact bearings are used. a) True b) False

Last Answer : b) False

A bushed-pin type flange coupling is used (A) For intersecting shafts (B) When the shafts are not in exact alignment (C) For small shafts rotating at slow speeds (D) For parallel shafts

Description : A bushed-pin type flange coupling is used (A) For intersecting shafts (B) When the shafts are not in exact alignment (C) For small shafts rotating at slow speeds (D) For parallel shafts

Last Answer : (B) When the shafts are not in exact alignment

There is a problem of alignment in deep groove ball bearings. (a) Yes (b) No, it is self-aligning (c) It aligns itself only in some particular cases (d) Can’t be determined

Description : There is a problem of alignment in deep groove ball bearings. (a) Yes (b) No, it is self-aligning (c) It aligns itself only in some particular cases (d) Can’t be determined

Last Answer : (a) Yes

There is problem of alignment in deep groove ball bearings. a) Yes b) No, it is self-aligning c) It aligns itself only in some particular cases d) Can’t be determined

Description : There is problem of alignment in deep groove ball bearings. a) Yes b) No, it is self-aligning c) It aligns itself only in some particular cases d) Can’t be determined

Last Answer : a) Yes

Match List I with List II and select the : [IES-2002] List I (Bearings) List II (Load type) A. Hydrodynamic Journal bearing 1. High radial and thrust load combined B. Rectangular Hydrostatic bearing 2. Radial load only C. Taper Roller bearing 3. Thrust load only D. Angular contact ball bearing 4. Medium to low radial and thrust combined A B C D A B C D (a) 2 3 1 4 (b) 4 1 3 2 (c) 2 1 3 4 (d) 4 3 1 2

Description : Match List I with List II and select the : [IES-2002] List I (Bearings) List II (Load type) A. Hydrodynamic Journal bearing 1. High radial and thrust load combined B. Rectangular Hydrostatic bearing 2. Radial load only C. Taper Roller ... (a) 2 3 1 4 (b) 4 1 3 2 (c) 2 1 3 4 (d) 4 3 1 2

Last Answer : (a) 2 3 1 4

Different types of bearings are designed to operate at different operating speeds. Speed is specified as the maximum (a) rpm (b) metres/second (c) metres/minute (d) metres/hour

Description : Different types of bearings are designed to operate at different operating speeds. Speed is specified as the maximum (a) rpm (b) metres/second (c) metres/minute (d) metres/hour

Last Answer : (b) metres/second

Deep groove ball bearings create a lot of noise. (a) Yes (b) Depends on the application (c) They create very less noise (d) No reference frame for comparison is mentioned

Description : Deep groove ball bearings create a lot of noise. (a) Yes (b) Depends on the application (c) They create very less noise (d) No reference frame for comparison is mentioned

Last Answer : (c) They create very less noise

Deep groove ball bearings creates a lot of noise. a) Yes b) They create very less noise c) Depends on the application d) No reference frame for comparison is mentioned

Description : Deep groove ball bearings creates a lot of noise. a) Yes b) They create very less noise c) Depends on the application d) No reference frame for comparison is mentioned

Last Answer : b) They create very less noise

________is suitable as a lubricant for low and moderate loads applications of rolling contact bearing. (a) Grease (b) Lubricating oil (c) Graphite (d) Air

Description : ________is suitable as a lubricant for low and moderate loads applications of rolling contact bearing. (a) Grease (b) Lubricating oil (c) Graphite (d) Air

Last Answer : (a) Grease

The ball bearing is subjected to a radial load of 4000 N. Expected life for 90% bearings is 9000 hr and the shaft is rot (a) 42.21 kN (b) 37.29 kN (c) 26.33 kN (d) 35.22 kN

Description : The ball bearing is subjected to a radial load of 4000 N. Expected life for 90% bearings is 9000 hr and the shaft is rot (a) 42.21 kN (b) 37.29 kN (c) 26.33 kN (d) 35.22 kN

Last Answer : (b) 37.29 kN

Calculate the bearing life if expected life for 90% bearings is 9000 hr and the shaft is rotating at 1500 rpm. (a) 850 million rev (b) 810 million rev (c) 810 hr (d) 850 hr

Description : Calculate the bearing life if expected life for 90% bearings is 9000 hr and the shaft is rotating at 1500 rpm. (a) 850 million rev (b) 810 million rev (c) 810 hr (d) 850 hr

Last Answer : (b) 810 million rev

Consider the following pairs of types of bearings and applications: 1. Partial Journal bearing................... Rail wagon axles 2. Full journal bearing ......................Diesel engine crank-shaft 3. Radial bearing ............................Combined radial and axial loads Which of these pairs is/are correctly matched? [IES-2000] (a) 1 alone (b) 1 and 2 (c) 2 and 3 (d) 1, 2 and 3

Description : Consider the following pairs of types of bearings and applications: 1. Partial Journal bearing................... Rail wagon axles 2. Full journal bearing ......................Diesel engine crank-shaft 3. Radial bearing ... matched? [IES-2000] (a) 1 alone (b) 1 and 2 (c) 2 and 3 (d) 1, 2 and 3

Last Answer : (b) 1 and 2

In an oil-lubricated journal bearing, coefficient of friction between the journal and the bearing. [IES-1995] (a) Remains constant at all speeds. (b) is minimum at zero speed and increases monotonically with increase in speed. (c) is maximum at zero speed and decreases monotonically with increase in speed. (d) becomes minimum at an optimum speed and then increases with further increase in speed.

Description : In an oil-lubricated journal bearing, coefficient of friction between the journal and the bearing. [IES-1995] (a) Remains constant at all speeds. (b) is minimum at zero speed and increases ... speed. (d) becomes minimum at an optimum speed and then increases with further increase in speed.

Last Answer : (d) becomes minimum at an optimum speed and then increases with further increase in speed.

The ball bearings are provided with a cage (a) to reduce friction (b) to facilitate slipping of balls (c) to prevent the lubricant from flowing out (d) to maintain the balls at a fixed distance apart

Description : The ball bearings are provided with a cage (a) to reduce friction (b) to facilitate slipping of balls (c) to prevent the lubricant from flowing out (d) to maintain the balls at a fixed distance apart

Last Answer : (d) to maintain the balls at a fixed distance apart

In a journal bearings, the radius of the friction circle increases with the increase in- [IES-1997] (a) Load (b) Radius of the journal (c) Speed of the journal (d) Viscosity of the lubricant

Description : In a journal bearings, the radius of the friction circle increases with the increase in- [IES-1997] (a) Load (b) Radius of the journal (c) Speed of the journal (d) Viscosity of the lubricant

Last Answer : (b) Radius of the journal

Which one of the following parts of a ball bearing is mounted on the rotating shafts and tends to rotate the shaft? (a) Inner race (b) Outer race (c) Rolling element (d) Cage

Description : Which one of the following parts of a ball bearing is mounted on the rotating shafts and tends to rotate the shaft? (a) Inner race (b) Outer race (c) Rolling element (d) Cage

Last Answer : (a) Inner race

Hot rolling produces a stronger shaft then cold rolling. a) True b) False

Description : Hot rolling produces a stronger shaft then cold rolling. a) True b) False

Last Answer : b) False

Hot rolling produces a stronger shaft then cold rolling. a) True b) False

Description : Hot rolling produces a stronger shaft then cold rolling. a) True b) False

Last Answer : b) False

The maximum frictional force which comes into play when a body just begins to slide over the surface of another body is known as a.Kinetic friction b.Rolling friction c.Dynamic friction d.Limiting friction e.Sliding friction

Description : The maximum frictional force which comes into play when a body just begins to slide over the surface of another body is known as a.Kinetic friction b.Rolling friction c.Dynamic friction d.Limiting friction e.Sliding friction

Last Answer : d. Limiting friction

Friction can be reduced by changing over from _____. A. Sliding to rolling B. Dynamic to static C. Potential energy to kinetic energy D. Rolling to sliding

Description : Friction can be reduced by changing over from _____. A. Sliding to rolling B. Dynamic to static C. Potential energy to kinetic energy D. Rolling to sliding

Last Answer : ANSWER: A

The maximum frictional force which comes into play when a body just begins to slide over another surface is called (A) Limiting friction (B) Sliding friction (C) Rolling friction (D) Kinematic friction

Description : The maximum frictional force which comes into play when a body just begins to slide over another surface is called (A) Limiting friction (B) Sliding friction (C) Rolling friction (D) Kinematic friction

Last Answer : (A) Limiting friction

Which of the following cannot tolerate misalignment? (a) Angular contact bearing (b) Cylinder roller bearing (c) Thrust ball bearings (d) All of the listed

Description : Which of the following cannot tolerate misalignment? (a) Angular contact bearing (b) Cylinder roller bearing (c) Thrust ball bearings (d) All of the listed

Last Answer : (d) All of the listed

Which of the bearings given below SHOULD NOT be subjected to a thrust load? (a) Deep groove ball bearing (b) Angular contact ball bearing (c) Cylindrical (straight) roller bearing (d) Single row tapered roller bearing

Description : Which of the bearings given below SHOULD NOT be subjected to a thrust load? (a) Deep groove ball bearing (b) Angular contact ball bearing (c) Cylindrical (straight) roller bearing (d) Single row tapered roller bearing

Last Answer : (c) Cylindrical (straight) roller bearing

In angular contact bearings, ____ bearings are required to take thrust load in both directions. (a) 1 (b) 2 (c) 3 (d) 4

Description : In angular contact bearings, ____ bearings are required to take thrust load in both directions. (a) 1 (b) 2 (c) 3 (d) 4

Last Answer : (b) 2

Which of the following cannot tolerate misalignment? a) Angular contact bearing b) Cylinder roller bearing c) Thrust ball bearings d) All of the listed

Description : Which of the following cannot tolerate misalignment? a) Angular contact bearing b) Cylinder roller bearing c) Thrust ball bearings d) All of the listed

Last Answer : d) All of the listed

In angular contact bearings, ____ bearings are required to take thrust load in both directions. a) 1 b) 4 c) 2 d) 3

Description : In angular contact bearings, ____ bearings are required to take thrust load in both directions. a) 1 b) 4 c) 2 d) 3

Last Answer : c) 2

The function of ball bearings in a wheel is – (1) to increase friction (2) to convert kinetic friction into rolling friction (3) to convert static friction into kinetic friction (4) just for convenience

Description : The function of ball bearings in a wheel is – (1) to increase friction (2) to convert kinetic friction into rolling friction (3) to convert static friction into kinetic friction (4) just for convenience

Last Answer : (2) to convert kinetic friction into rolling friction Explanation: A ball bearing is a type of rollingelement bearing that uses balls to maintain the separation between the bearing races. The purpose of a ball bearing is to reduce rotational friction and support radial and axial loads.

The function of ball bearings in a wheel is : (1) to increase friction (2) to convert kinetic friction into rolling friction (3) to convert static friction into kinetic friction (4) just for convenience

Description : The function of ball bearings in a wheel is : (1) to increase friction (2) to convert kinetic friction into rolling friction (3) to convert static friction into kinetic friction (4) just for convenience

Last Answer : to convert kinetic friction into rolling friction

Consider tile following statements: [IES-1993; 2002; 2006] Radius of friction circle for a journal bearing depends upon 1. Coefficient of friction 2. Radius of the journal 3. Angular speed of rotation of the shaft Which of the statements given above are correct? (a) 1,2 and 3 (b) Only 1 and 2 (c) Only 2 and 3 (d) Only 1 and 3

Description : Consider tile following statements: [IES-1993; 2002; 2006] Radius of friction circle for a journal bearing depends upon 1. Coefficient of friction 2. Radius of the journal 3. Angular speed of rotation of the shaft Which of the ... ) 1,2 and 3 (b) Only 1 and 2 (c) Only 2 and 3 (d) Only 1 and 3

Last Answer : (b) Only 1 and 2

Increase in values of which of the following results in an increase of the coefficient of friction in a hydrodynamic bearing? [IES 2007] 1. Viscosity of the oil. 2. Clearance between shaft and bearing. 3. Shaft speed. Select the using the code given below: (a) 1 and 2 only (b) 1 and 3 only (c) 2 and 3 only (d) 1, 2 and 3

Description : Increase in values of which of the following results in an increase of the coefficient of friction in a hydrodynamic bearing? [IES 2007] 1. Viscosity of the oil. 2. Clearance between shaft and bearing. 3. Shaft speed. Select the ... 1 and 2 only (b) 1 and 3 only (c) 2 and 3 only (d) 1, 2 and 3

Last Answer : (b) 1 and 3 only

Which of the following are not true for petroff’s equation? a) Shaft is considered concentric with the bearing b) Bearing is subjected to light load c) Is used to find coefficient of friction d) Frictional torque is given by fpr2l

Description : Which of the following are not true for petroff’s equation? a) Shaft is considered concentric with the bearing b) Bearing is subjected to light load c) Is used to find coefficient of friction d) Frictional torque is given by fpr2l

Last Answer : d) Frictional torque is given by fpr2l

If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the diameter of each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. Permissible tensile stress is 80N/mm2. a) 27mm b) 25mm c) 23mm d) 21mm

Description : If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the diameter of each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. Permissible tensile stress is 80N/mm2. a) 27mm b) 25mm c) 23mm d) 21mm

Last Answer : a) 27mm

If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the tensile force on each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. a) 51234.4N b) 45968.3N c) 41666.7N d) None of the listed

Description : If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the tensile force on each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. a) 51234.4N b) 45968.3N c) 41666.7N d) None of the listed

Last Answer : c) 41666.7N

_______is suitable as a lubricant for heavy-duty applications of rolling contact bearing. (a) Grease (b) Lubricating oil (c) Graphite (d) Air

Description : _______is suitable as a lubricant for heavy-duty applications of rolling contact bearing. (a) Grease (b) Lubricating oil (c) Graphite (d) Air

Last Answer : (b) Lubricating oil

A rolling contact bearing is specified as X307. Calculate the bearing diameter. (a) 35 mm (b) 28 mm (c) 21 mm (d) 7 mm

Description : A rolling contact bearing is specified as X307. Calculate the bearing diameter. (a) 35 mm (b) 28 mm (c) 21 mm (d) 7 mm

Last Answer : (a) 35 mm

Rolling contact bearing is also called as A. Plastic bearing B. Thin lubrication bearing C. Thick lubrication bearing D. Antifriction bearing.

Description : Rolling contact bearing is also called as A. Plastic bearing B. Thin lubrication bearing C. Thick lubrication bearing D. Antifriction bearing.

Last Answer : D. Antifriction bearing.

A rolling contact bearing is specified as X307. Determine the series. a) Extra light series b) Light series c) Medium series d) Heavy series

Description : A rolling contact bearing is specified as X307. Determine the series. a) Extra light series b) Light series c) Medium series d) Heavy series

Last Answer : c) Medium series

Which of the following elements is not used as a roller in roller bearings? (a) Cylindrical (b) Taper (c) Spherical (d) None of the mentioned

Description : Which of the following elements is not used as a roller in roller bearings? (a) Cylindrical (b) Taper (c) Spherical (d) None of the mentioned

Last Answer : (d) None of the mentioned

The construction feature which makes tapered roller bearings unique in that races are (a) attachable (b) separable (c) self-aligning (d) none of the mentioned

Description : The construction feature which makes tapered roller bearings unique in that races are (a) attachable (b) separable (c) self-aligning (d) none of the mentioned

Last Answer : (b) separable

Which of the following bearings carry thrust load in one direction? (a) Spherical roller thrust bearings (b) Taper roller bearings (c) Spherical roller thrust bearings and taper roller bearings (d) none of the mentioned

Description : Which of the following bearings carry thrust load in one direction? (a) Spherical roller thrust bearings (b) Taper roller bearings (c) Spherical roller thrust bearings and taper roller bearings (d) none of the mentioned

Last Answer : (c) Spherical roller thrust bearings and taper roller bearings