The axial deflection of spring for the small angle of θ is given by? a) 328PDɜN/Gd4 b) 8PDɜN/Gd4 c) 16PDɜN/Gd4 d) 8PD2N/Gdɜ

The axial deflection of spring for the small angle of θ is given by?

a) 328PDɜN/Gd4

b) 8PDɜN/Gd4

c) 16PDɜN/Gd4

d) 8PD2N/Gdɜ
by

1 Answer

Answer :

b) 8PDɜN/Gd4
by

Related questions

The angle of twist for the equivalent bar to a spring is given by? (Symbols have their usual meaning) a) 8PD2N/Gd4 b) 16PD2N/Gd4 c) 16PDN/Gdɜ d) 8PDN/Gdɜ

Description : The angle of twist for the equivalent bar to a spring is given by? (Symbols have their usual meaning) a) 8PD2N/Gd4 b) 16PD2N/Gd4 c) 16PDN/Gdɜ d) 8PDN/Gdɜ

Last Answer : b) 16PD2N/Gd4

The axial deflection of spring for the small angle of θ is given by? a) 328PDᵌN/Gd⁴ b) 8PDᵌN/Gd⁴ c) 16PDᵌN/Gd⁴ d) 8PD²N/Gdᵌ

Description : The axial deflection of spring for the small angle of θ is given by? a) 328PDᵌN/Gd⁴ b) 8PDᵌN/Gd⁴ c) 16PDᵌN/Gd⁴ d) 8PD²N/Gdᵌ

Last Answer : b) 8PDᵌN/Gd⁴

While designing shaft on the basis of torsional rigidity, angle of twist is given by? a) Ml/Gd4 b) 584Ml/Gd4 c) 292 Ml/Gd4 d) None of the mentioned

Description : While designing shaft on the basis of torsional rigidity, angle of twist is given by? a) Ml/Gd4 b) 584Ml/Gd4 c) 292 Ml/Gd4 d) None of the mentioned

Last Answer : b) 584Ml/Gd4

While designing shaft on the basis of torsional rigidity, angle of twist is given by? a) Ml/Gd4 b) 584Ml/Gd4 c) 292 Ml/Gd4 d) None of the mentioned

Description : While designing shaft on the basis of torsional rigidity, angle of twist is given by? a) Ml/Gd4 b) 584Ml/Gd4 c) 292 Ml/Gd4 d) None of the mentioned

Last Answer : b) 584Ml/Gd4

The stiffness of spring is, (A) Deflection per unit of axial force (B) Force per unit cross-sectional area of spring (C) Ratio of mean coil diameter to wire diameter (D) Force required to produce unit deflection

Description : The stiffness of spring is, (A) Deflection per unit of axial force (B) Force per unit cross-sectional area of spring (C) Ratio of mean coil diameter to wire diameter (D) Force required to produce unit deflection

Last Answer : (D) Force required to produce unit deflection

Deflection in a close coiled helical spring is (a) 16 WR3n/Gd4 (b) 32 WR3n/Gd4 (c) 64 WR3n/Gd4 (d) None

Description : Deflection in a close coiled helical spring is (a) 16 WR3n/Gd4 (b) 32 WR3n/Gd4 (c) 64 WR3n/Gd4 (d) None

Last Answer : (c) 64 WR3n/Gd4

The strain energy (E) stored in the spring is given by Where P=Load and δ = deflection of spring (A) Pδ/2 (B) 2Pδ (C) Pδ/3 (D) Pδ/4

Description : The strain energy (E) stored in the spring is given by Where P=Load and δ = deflection of spring (A) Pδ/2 (B) 2Pδ (C) Pδ/3 (D) Pδ/4

Last Answer : (A) Pδ/2

Axial length of an unloaded helical compression spring is called (A) compressed length (B) solid length (C) free length (D) none of the above

Description : Axial length of an unloaded helical compression spring is called (A) compressed length (B) solid length (C) free length (D) none of the above

Last Answer : (C) free length

Axial length of the spring which is so compressed that the adjacent coils touch each other. (A) compressed length (B) solid length (C) free length (D) none of the above

Description : Axial length of the spring which is so compressed that the adjacent coils touch each other. (A) compressed length (B) solid length (C) free length (D) none of the above

Last Answer : (B) solid length

When two concentric springs are made of same material, having same free length and compressed equally by axial load, then the load shared by each spring is proportional to (A) Spring index of each spring (B) Wire diameter of each spring (C) Mean coil diameter of each spring (D) Square of wire diameter of each spring

Description : When two concentric springs are made of same material, having same free length and compressed equally by axial load, then the load shared by each spring is proportional to (A) Spring index of each spring ... spring (C) Mean coil diameter of each spring (D) Square of wire diameter of each spring

Last Answer : (D) Square of wire diameter of each spring

When the helical compression spring is subjected to axial compressive force, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress

Description : When the helical compression spring is subjected to axial compressive force, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress

Last Answer : (D) Torsional shear stress

When the helical extension spring is subjected to axial tensile force, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress

Description : When the helical extension spring is subjected to axial tensile force, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress

Last Answer : (D) Torsional shear stress

The current I passing through the galvanometer coil is related to the angle of deflection θ as a) I ∝ θ b) I 1/∝ θ c) I ∝ θ 2 d) I 1/∝ θ 2

Description : The current I passing through the galvanometer coil is related to the angle of deflection θ as a) I ∝ θ b) I 1/∝ θ c) I ∝ θ 2 d) I 1/∝ θ 2

Last Answer : a) I ∝ θ

The force required to produce unit deflection is known as (A) gradient of spring (B) stiffness of the spring (C) spring constant (D) all of the above

Description : The force required to produce unit deflection is known as (A) gradient of spring (B) stiffness of the spring (C) spring constant (D) all of the above

Last Answer : (D) all of the above

The spring index is, (A) Ratio of wire diameter to mean coil diameter (B) Force per unit cross-sectional area of spring (C) Ratio of mean coil diameter to wire diameter (D) Force required to produce unit deflection

Description : The spring index is, (A) Ratio of wire diameter to mean coil diameter (B) Force per unit cross-sectional area of spring (C) Ratio of mean coil diameter to wire diameter (D) Force required to produce unit deflection

Last Answer : (C) Ratio of mean coil diameter to wire diameter

The type of spring used to achieve any linear or non-linear load-deflection characteristic is (A) Spiral spring (B) Non-ferrous spring (C) Belleville (coned disk) spring (D) Torsion spring

Description : The type of spring used to achieve any linear or non-linear load-deflection characteristic is (A) Spiral spring (B) Non-ferrous spring (C) Belleville (coned disk) spring (D) Torsion spring

Last Answer : (C) Belleville (coned disk) spring

Belleville spring can only produce linear load deflection characteristics. a) Only linear b) Linear as well as non linear c) Non-linear d) None of the mentioned

Description : Belleville spring can only produce linear load deflection characteristics. a) Only linear b) Linear as well as non linear c) Non-linear d) None of the mentioned

Last Answer : b) Linear as well as non linear

The helix angle is very small about 20. The spring is open coiled spring. a) Yes b) It is closed coiled spring c) That small angle isn’t possible d) None of the listed

Description : The helix angle is very small about 20. The spring is open coiled spring. a) Yes b) It is closed coiled spring c) That small angle isn’t possible d) None of the listed

Last Answer : b) It is closed coiled spring

In trapezoidal threads, f (coefficient of friction) can be taken as a) f sec θ b) f cos θ c) f sin θ d) f cosec θ

Description : In trapezoidal threads, f (coefficient of friction) can be taken as a) f sec θ b) f cos θ c) f sin θ d) f cosec θ

Last Answer : a) f sec θ

A force 2P is acting on the double transverse fillet weld. Leg of weld is h and length l. Determine the shear stress in a plane inclined at θ with horizontal. a) PSinθ(Sinθ+Cosθ)/hl b) P(Sinθ+Cosθ)/hl c) Pcosθ(Sinθ+Cosθ)/hl d) None of the listed

Description : A force 2P is acting on the double transverse fillet weld. Leg of weld is h and length l. Determine the shear stress in a plane inclined at θ with horizontal. a) PSinθ(Sinθ+Cosθ)/hl b) P(Sinθ+Cosθ)/hl c) Pcosθ(Sinθ+Cosθ)/hl d) None of the listed

Last Answer : a) PSinθ(Sinθ+Cosθ)/hl

A force 2P is acting on the double transverse fillet weld. Leg of weld is h and length l. Determine the shear stress in a plane inclined at θ with horizontal. a) PSinθ(Sinθ+Cosθ)/hl b) P(Sinθ+Cosθ)/hl c) Pcosθ(Sinθ+Cosθ)/hl d) None of the listed

Description : A force 2P is acting on the double transverse fillet weld. Leg of weld is h and length l. Determine the shear stress in a plane inclined at θ with horizontal. a) PSinθ(Sinθ+Cosθ)/hl b) P(Sinθ+Cosθ)/hl c) Pcosθ(Sinθ+Cosθ)/hl d) None of the listed

Last Answer : a) PSinθ(Sinθ+Cosθ)/hl

The maximum tangential stress σ t = (σ x sin 2θ)/2 is maximum if, θ is equal to ________ a. 45 o b. 90 o c. 270 o d. all of the above

Description : The maximum tangential stress σ t = (σ x sin 2θ)/2 is maximum if, θ is equal to ________ a. 45 o b. 90 o c. 270 o d. all of the above

Last Answer : a. 45 o

Which of the following formulae is used to calculate tangential stress, when a member is subjected to stress in mutually perpendicular axis and accompanied by a shear stress? a. [(σ x – σ y )/2 ]sin θ – τ cos 2θ b. [(σ x – σ y )/2 ]– τ cos 2θ c. [(σ x – σ y )/2 ]sin θ – τ 2 cos θ d. None of the above

Description : Which of the following formulae is used to calculate tangential stress, when a member is subjected to stress in mutually perpendicular axis and accompanied by a shear stress? a. [(σ x - σ y )/2 ]sin θ - τ cos 2θ b. [(σ x - ... τ cos 2θ c. [(σ x - σ y )/2 ]sin θ - τ 2 cos θ d. None of the above

Last Answer : c. [(σ x – σ y )/2 ]sin θ – τ 2 cos θ

A closely coiled helical spring of radius R, contains n turns and is subjected to an axial load W. If the radius of the coil wire is r and modulus of rigidity of the coil material is C, the deflection of the coil is (A) WR3n/Cr4 (B) 2WR3n/Cr4 (C) 3WR3n/Cr4 (D) 4WR3n/Cr

Description : A closely coiled helical spring of radius R, contains n turns and is subjected to an axial load W. If  the radius of the coil wire is r and modulus of rigidity of the coil material is C, the deflection of the  coil is  (A) WR3n/Cr4 (B) 2WR3n/Cr4 (C) 3WR3n/Cr4 (D) 4WR3n/Cr

Last Answer : (D) 4WR3n/Cr

Match List-I (Type of Anti-friction bearing) with List-II (Specific Use) and select the using the code given below the Lists: [IES-2006] List-I List -II A. Self-aligning ball bearing 1. For pure axial load B. Taper roller bearing 2. For hinged condition C. Deep groove ball bearing 3. For pure radial load D. Thrust ball bearing 4. For axial and radial load A B C D A B C D (a) 2 1 3 4 (b) 3 4 2 1 (c) 2 4 3 1 (d) 3 1 2 4

Description : Match List-I (Type of Anti-friction bearing) with List-II (Specific Use) and select the using the code given below the Lists: [IES-2006] List-I List -II A. Self-aligning ball bearing 1. For pure axial load B. Taper roller bearing 2. For ... C D (a) 2 1 3 4 (b) 3 4 2 1 (c) 2 4 3 1 (d) 3 1 2 4

Last Answer : (c) 2 4 3 1

The helix angle in case of closely coiled helical spring is (A) less than 5° (B) 5° to 7° (C) 7° to 10° (D) more than 10°

Description : The helix angle in case of closely coiled helical spring is (A) less than 5° (B) 5° to 7° (C) 7° to 10° (D) more than 10°

Last Answer : (D) more than 10°

The helix angle in case of closely coiled helical spring is (A) less than 10° (B) 10° to 15° (C) 15° to 20° (D) more than 20°

Description : The helix angle in case of closely coiled helical spring is (A) less than 10° (B) 10° to 15° (C) 15° to 20° (D) more than 20°

Last Answer : (A) less than 10°

When two Belleville springs are in parallel, half force is obtained for a given deflection. a) Half force b) Double force c) Same force d) Can’t be determined

Description : When two Belleville springs are in parallel, half force is obtained for a given deflection. a) Half force b) Double force c) Same force d) Can’t be determined

Last Answer : b) Double force

Feather key can be used to prevent axial motion between two elements. a) True b) False

Description : Feather key can be used to prevent axial motion between two elements. a) True b) False

Last Answer : b) False

Tapered roller bearings can take (a) radial load only (b) axial load only (c) both radial and axial loads and the ratio of these being greater than unity (d) both radial and axial loads and the ratio of these being less than unity

Description : Tapered roller bearings can take (a) radial load only (b) axial load only (c) both radial and axial loads and the ratio of these being greater than unity (d) both radial and axial loads and the ratio of these being less than unity

Last Answer : (c) both radial and axial loads and the ratio of these being greater than unity

The angular play bearing must be mounted without axial play. (a) Yes (b) Little tolerance is adjusted

Description : The angular play bearing must be mounted without axial play. (a) Yes (b) Little tolerance is adjusted

Last Answer : (a) Yes

Load acting on bearing in its plane of rotation is called as a... A. Radial load B. Axial load C. Perpendicular load D. Thrust load

Description : Load acting on bearing in its plane of rotation is called as a... A. Radial load B. Axial load C. Perpendicular load D. Thrust load

Last Answer : A. Radial load

The tapered roller bearings can take (a) radial load only (b) axial load only (c) both radial and axial loads (d) none of the mentioned

Description : The tapered roller bearings can take (a) radial load only (b) axial load only (c) both radial and axial loads (d) none of the mentioned

Last Answer : (c) both radial and axial loads

A cotter joint is used to connect two __________ rods. A. Co-axial B. Perpendicular C. Parallel D. None of these

Description : A cotter joint is used to connect two __________ rods. A. Co-axial B. Perpendicular C. Parallel D. None of these

Last Answer : A. Co-axial

Consider the following pairs of types of bearings and applications: 1. Partial Journal bearing................... Rail wagon axles 2. Full journal bearing ......................Diesel engine crank-shaft 3. Radial bearing ............................Combined radial and axial loads Which of these pairs is/are correctly matched? [IES-2000] (a) 1 alone (b) 1 and 2 (c) 2 and 3 (d) 1, 2 and 3

Description : Consider the following pairs of types of bearings and applications: 1. Partial Journal bearing................... Rail wagon axles 2. Full journal bearing ......................Diesel engine crank-shaft 3. Radial bearing ... matched? [IES-2000] (a) 1 alone (b) 1 and 2 (c) 2 and 3 (d) 1, 2 and 3

Last Answer : (b) 1 and 2

Footstep bearing is an axial load bearing. a) True b) Thrust load c) Shear load d) None of the listed

Description : Footstep bearing is an axial load bearing. a) True b) Thrust load c) Shear load d) None of the listed

Last Answer : b) Thrust load

A journal bearing is a ______ contact bearing working on the hydrodynamic lubrication and which supports load in____ direction. a) Sliding, Axial b) Rolling, Radial c) Sliding, Radial d) Rolling, Axial

Description : A journal bearing is a ______ contact bearing working on the hydrodynamic lubrication and which supports load in____ direction. a) Sliding, Axial b) Rolling, Radial c) Sliding, Radial d) Rolling, Axial

Last Answer : c) Sliding, Radial

Taper rolling supports a) Axial loads b) Thrust loads c) Both axial and thrust loads d) None of the mentioned

Description : Taper rolling supports a) Axial loads b) Thrust loads c) Both axial and thrust loads d) None of the mentioned

Last Answer : c) Both axial and thrust loads

The angular play bearing must be mounted without axial play. a) Yes b) Little tolerance is adjusted c) Little tolerance is necessary d) Can’t be stated

Description : The angular play bearing must be mounted without axial play. a) Yes b) Little tolerance is adjusted c) Little tolerance is necessary d) Can’t be stated

Last Answer : a) Yes

The leaves of multi-leaf springs are subjected to (A) bending stress (B) shear stress (C) axial stress (D) all of the above

Description : The leaves of multi-leaf springs are subjected to (A) bending stress (B) shear stress (C) axial stress (D) all of the above

Last Answer : (A) bending stress

Pitch of coil is defined as axial distance in compressed state of the coil. a) Yes b) It is measured in uncompressed state c) It is same in uncompressed or compressed state d) None of the listed

Description : Pitch of coil is defined as axial distance in compressed state of the coil. a) Yes b) It is measured in uncompressed state c) It is same in uncompressed or compressed state d) None of the listed

Last Answer : b) It is measured in uncompressed state

Cotter joint is employed when the members are subjected to which sort of stresses? a) Axial tensile b) Axial compressive c) Axial tensile or compressive d) None of the above

Description : Cotter joint is employed when the members are subjected to which sort of stresses? a) Axial tensile b) Axial compressive c) Axial tensile or compressive d) None of the above

Last Answer : c) Axial tensile or compressive

Cotter joints is used for transforming........... A. Axial compressive load B. Axial tensile load C. Axial tensile or compressive load D. Twisting load

Description : Cotter joints is used for transforming........... A. Axial compressive load B. Axial tensile load C. Axial tensile or compressive load D. Twisting load

Last Answer : C. Axial tensile or compressive load

Cotter joints is connected two ......... roads. A. Co - axial B. Parallel C. Perpendicular D. Inclined

Description : Cotter joints is connected two ......... roads. A. Co - axial B. Parallel C. Perpendicular D. Inclined

Last Answer : A. Co - axial

Cotter joints is used for transforming........... A. Axial compressive load B. Axial tensile load C. Axial tensile or compressive load D. Twisting load

Description : Cotter joints is used for transforming........... A. Axial compressive load B. Axial tensile load C. Axial tensile or compressive load D. Twisting load

Last Answer : C. Axial tensile or compressive load

Cotter joints is connected two ......... roads. A. Co - axial B. Parallel C. Perpendicular D. Inclined

Description : Cotter joints is connected two ......... roads. A. Co - axial B. Parallel C. Perpendicular D. Inclined

Last Answer : A. Co - axial

Cotter joint is used when the members are subjected to which type of stresses? a) Axial tensile b) Axial compressive c) Axial tensile or compressive d) None of the mentioned

Description : Cotter joint is used when the members are subjected to which type of stresses? a) Axial tensile b) Axial compressive c) Axial tensile or compressive d) None of the mentioned

Last Answer : c) Axial tensile or compressive

The resultant axial force on bolt depends upon (A) Initial tension (B) External applied load (C) Stiffness of bolt and parts held by bolt (D) All three factors

Description : The resultant axial force on bolt depends upon (A) Initial tension (B) External applied load (C) Stiffness of bolt and parts held by bolt (D) All three factors

Last Answer : (D) All three factors

Does shaft has to be shifted i axial direction to remove clamp coupling. a) Yes b) No

Description : Does shaft has to be shifted i axial direction to remove clamp coupling. a) Yes b) No

Last Answer : b) No

Woodruff key permits _____ movement b/w shaft and the hub. a) Axial b) Radial c) Eccentric d) None of the listed

Description : Woodruff key permits _____ movement b/w shaft and the hub. a) Axial b) Radial c) Eccentric d) None of the listed

Last Answer : b) Radial