The maximum shear stress in spring wire is induced at (A) Inner surface of the coil (B) Outer surface of the coil (C) Central surface of the coil (D) End coils

The maximum shear stress in spring wire is induced at

(A) Inner surface of the coil

(B) Outer surface of the coil

(C) Central surface of the coil

(D) End coils
by

1 Answer

Answer :

(A) Inner surface of the coil
by

Related questions

When the helical torsion spring is subjected to torque, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress

Description : When the helical torsion spring is subjected to torque, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress

Last Answer : (C) Bending stress

When the helical compression spring is subjected to axial compressive force, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress

Description : When the helical compression spring is subjected to axial compressive force, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress

Last Answer : (D) Torsional shear stress

When the helical extension spring is subjected to axial tensile force, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress

Description : When the helical extension spring is subjected to axial tensile force, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress

Last Answer : (D) Torsional shear stress

Torsional shear stresses are induced in the spring wire when (A) spring is under compression (B) spring is under tension (C) both (A) and (B) (D) none of the above

Description : Torsional shear stresses are induced in the spring wire when (A) spring is under compression (B) spring is under tension (C) both (A) and (B) (D) none of the above

Last Answer : (C) both (A) and (B)

A compression spring is made of music wire of 2 mm diameter having a shear strength and shear modulus of 800 Mpa and 80 Gpa respectively. The mean coil diameter is 20mm, free length is 40 mm, and the number of active coils is 10. If the mean coil diameter is reduced to 10 mm, the stiffness of the spring is approximately a. increased by 8 times b. decreased by 2 times c. increased by 2 times d. decreased by 8 times

Description : A compression spring is made of music wire of 2 mm diameter having a shear strength and shear modulus of 800 Mpa and 80 Gpa respectively. The mean coil diameter is 20mm, free length is 40 mm, and the number ... by 8 times b. decreased by 2 times c. increased by 2 times d. decreased by 8 times

Last Answer : a. increased by 8 times

If uncompressed length of spring is 40mm and number of coils 10mm, then pitch of coil is? a) 4 b) 40/9 c) 40/11 d) None of the mentioned

Description : If uncompressed length of spring is 40mm and number of coils 10mm, then pitch of coil is? a) 4 b) 40/9 c) 40/11 d) None of the mentioned

Last Answer : b) 40/9

A hollow prismatic beam of circular section is subjected to a torsional moment. The maximum shear stress occurs at (a) inner wall of cross section (b) middle of thickness (c) outer surface of shaft (d) none of these

Description : A hollow prismatic beam of circular section is subjected to a torsional moment. The maximum shear stress occurs at (a) inner wall of cross section (b) middle of thickness (c) outer surface of shaft (d) none of these

Last Answer : (c) outer surface of shaft

Maximum shear stress in a hollow shaft subjected to a torsional moment is at the a. Middle of thickness. b. At the inner surface of the shaft. c. At the outer surface of the shaft. d. At the middle surface of the shaft.

Description : Maximum shear stress in a hollow shaft subjected to a torsional moment is at the a. Middle of thickness. b. At the inner surface of the shaft. c. At the outer surface of the shaft. d. At the middle surface of the shaft.

Last Answer : c. At the outer surface of the shaft.

If number of coils are 8 and wire diameter of spring 3mm, then solid length is given by? a) None of the listed b) 27mm c) 24mm d) 21mm

Description : If number of coils are 8 and wire diameter of spring 3mm, then solid length is given by? a) None of the listed b) 27mm c) 24mm d) 21mm

Last Answer : c) 24mm

-The method used to induce a layer of residual compressive stress on the surface of the spring wire, is (A) shot peening (B) burnishing (C) lapping (D) none of the above

Description : -The method used to induce a layer of residual compressive stress on the surface of the spring wire, is (A) shot peening (B) burnishing (C) lapping (D) none of the above

Last Answer : (A) shot peening

A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and breadth of the key being 14mm and 80mm respectively. Find the shear stress induced in the key. a) 30.2N/mm2 b) 25.8N/mm2 c) 34.4N/mm2 d) None of the listed

Description : A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and breadth of the key being 14mm and 80mm respectively. Find the shear stress induced in the key. a) 30.2N/mm2 b) 25.8N/mm2 c) 34.4N/mm2 d) None of the listed

Last Answer : b) 25.8N/mm2

The compressive stress induced in a square key is, (A) Equal to shear stress (B) Four times of shear stress (C) Twice of shear stress (D) Half of shear stress

Description : The compressive stress induced in a square key is, (A) Equal to shear stress (B) Four times of shear stress (C) Twice of shear stress (D) Half of shear stress

Last Answer : (C) Twice of shear stress

A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and breadth of the key being 14mm and 80mm respectively. Find the shear stress induced in the key. a) 30.2N/mm2 b) 25.8N/mm2 c) 34.4N/mm2 d) None of the listed

Description : A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and breadth of the key being 14mm and 80mm respectively. Find the shear stress induced in the key. a) 30.2N/mm2 b) 25.8N/mm2 c) 34.4N/mm2 d) None of the listed

Last Answer : b) 25.8N/mm2

What is the shear stress acting on the outer surface of a hollow shaft subjected to a torque of 100 Nm?(The inner and outer diameter of the shaft is 15 mm and 30 mm respectively.) a. 50.26 N/mm2 b. 40.24 N/mm2 c. 20.120 N/mm2 d. 8.74 N/mm2

Description : What is the shear stress acting on the outer surface of a hollow shaft subjected to a torque of 100 Nm?(The inner and outer diameter of the shaft is 15 mm and 30 mm respectively.) a. 50.26 N/mm2 b. 40.24 N/mm2 c. 20.120 N/mm2 d. 8.74 N/mm2

Last Answer : c. 20.120 N/mm2

The spring index (C) is (A) mean coil diameter / wire diameter (B) wire diameter / mean coil diameter (C) wire diameter x mean coil diameter (D) none of the above

Description : The spring index (C) is (A) mean coil diameter / wire diameter (B) wire diameter / mean coil diameter (C) wire diameter x mean coil diameter (D) none of the above

Last Answer : (A) mean coil diameter / wire diameter

The spring index is, (A) Ratio of wire diameter to mean coil diameter (B) Force per unit cross-sectional area of spring (C) Ratio of mean coil diameter to wire diameter (D) Force required to produce unit deflection

Description : The spring index is, (A) Ratio of wire diameter to mean coil diameter (B) Force per unit cross-sectional area of spring (C) Ratio of mean coil diameter to wire diameter (D) Force required to produce unit deflection

Last Answer : (C) Ratio of mean coil diameter to wire diameter

When two concentric springs are made of same material, having same free length and compressed equally by axial load, then the load shared by each spring is proportional to (A) Spring index of each spring (B) Wire diameter of each spring (C) Mean coil diameter of each spring (D) Square of wire diameter of each spring

Description : When two concentric springs are made of same material, having same free length and compressed equally by axial load, then the load shared by each spring is proportional to (A) Spring index of each spring ... spring (C) Mean coil diameter of each spring (D) Square of wire diameter of each spring

Last Answer : (D) Square of wire diameter of each spring

The stiffness of spring is, (A) Deflection per unit of axial force (B) Force per unit cross-sectional area of spring (C) Ratio of mean coil diameter to wire diameter (D) Force required to produce unit deflection

Description : The stiffness of spring is, (A) Deflection per unit of axial force (B) Force per unit cross-sectional area of spring (C) Ratio of mean coil diameter to wire diameter (D) Force required to produce unit deflection

Last Answer : (D) Force required to produce unit deflection

The spring index is the ratio of wire diameter to mean coil diameter. a) True b) False

Description : The spring index is the ratio of wire diameter to mean coil diameter. a) True b) False

Last Answer : a) True

If the strain energy stored per unit volume in a hollow shaft subjected to a pure torque when t attains maximum shear stress fs the ratio of inner diameter to outer diameter, is 17/64 (fs/N) (A) 1/2 (B) 1/3 (C) 1/4 (D) 1/5

Description : If the strain energy stored per unit volume in a hollow shaft subjected to a pure torque  when t attains maximum shear stress fs  the ratio of inner diameter to outer diameter, is 17/64  (fs/N)  (A) 1/2  (B) 1/3  (C) 1/4  (D) 1/5

Last Answer : (C) 1/4 

Which of the following is incorrect? a. In a solid shaft maximum shear stress occurs at radius = radius of shaft b. In a solid shaft maximum shear stress occurs at center c. In a hollow shaft maximum shear stress occurs at outer radius d. In a hollow shaft minimum shear stress occurs at inner radius

Description : Which of the following is incorrect? a. In a solid shaft maximum shear stress occurs at radius = radius of shaft b. In a solid shaft maximum shear stress occurs at center c. In a hollow ... maximum shear stress occurs at outer radius d. In a hollow shaft minimum shear stress occurs at inner radius

Last Answer : b. In a solid shaft maximum shear stress occurs at center

The ends of spring, which are in contact with the seat, are (A) Active coils (B) Inactive coils (C) Transmit maximum force (D) Do not transmit any force

Description : The ends of spring, which are in contact with the seat, are (A) Active coils (B) Inactive coils (C) Transmit maximum force (D) Do not transmit any force

Last Answer : (B) Inactive coils

The helical spring ad wire of helical torsion spring, both are subjected to torsional shear stresses. a) True b) False

Description : The helical spring ad wire of helical torsion spring, both are subjected to torsional shear stresses. a) True b) False

Last Answer : b) False

What will happen if stresses induced due to surge in the spring exceeds the endurance limit stress of the spring. a) Fatigue Failure b) Fracture c) None of the listed d) Nipping

Description : What will happen if stresses induced due to surge in the spring exceeds the endurance limit stress of the spring. a) Fatigue Failure b) Fracture c) None of the listed d) Nipping

Last Answer : a) Fatigue Failure

For a helical torsion sprig, the stress concentration factor at outer fibre is? Give spring index=5. a) 0.78 b) 0.87 c) 1.87 d) 0.69

Description : For a helical torsion sprig, the stress concentration factor at outer fibre is? Give spring index=5. a) 0.78 b) 0.87 c) 1.87 d) 0.69

Last Answer : b) 0.87

For a helical torsion sprig, the stress concentration factor at inner fibre is? Give spring index=5. a) 1.005 b) 1.175 c) 1.223 d) 1.545

Description : For a helical torsion sprig, the stress concentration factor at inner fibre is? Give spring index=5. a) 1.005 b) 1.175 c) 1.223 d) 1.545

Last Answer : b) 1.175

A hollow shaft has an inner diameter of 3.7 cm and an outer diameter of 4.0 cm. A 1 kN-m torque is applied to this shaft. What is the shear stress at the mid-radius of this shaft? (a) 117Mpa (b) 178 Mpa (c) 286 Mpa (d) 363 Mpa

Description : A hollow shaft has an inner diameter of 3.7 cm and an outer diameter of 4.0 cm. A 1 kN-m torque is applied to this shaft. What is the shear stress at the mid-radius of this shaft? (a) 117Mpa (b) 178 Mpa (c) 286 Mpa (d) 363 Mpa

Last Answer : (c) 286 Mpa

The coils of spring which are in contact with the seat and do not contribute to spring action are called (A) resting coils (B) static coils (C) inactive coils (D) ideal coils

Description : The coils of spring which are in contact with the seat and do not contribute to spring action are called (A) resting coils (B) static coils (C) inactive coils (D) ideal coils

Last Answer : (C) inactive coils

Axial length of the spring which is so compressed that the adjacent coils touch each other. (A) compressed length (B) solid length (C) free length (D) none of the above

Description : Axial length of the spring which is so compressed that the adjacent coils touch each other. (A) compressed length (B) solid length (C) free length (D) none of the above

Last Answer : (B) solid length

Active and inactive, both types of coils support the load although both don’t participate in spring action. a) Active coils don’t support the load b) Inactive coils don’t support the load c) Both active and inactive don’t support the load d) Both active and inactive support the load

Description : Active and inactive, both types of coils support the load although both don’t participate in spring action. a) Active coils don’t support the load b) Inactive coils don’t support the load c) Both active and inactive don’t support the load d) Both active and inactive support the load

Last Answer : b) Inactive coils don’t support the load

If the spring is compressed completely and the adjacent coils touch each other,the the length of spring is called as? a) Solid length b) Compressed length c) Free length d) None of the mentioned

Description : If the spring is compressed completely and the adjacent coils touch each other,the the length of spring is called as? a) Solid length b) Compressed length c) Free length d) None of the mentioned

Last Answer : a) Solid length

In a thick cylindrical shell subjected to an internal pressure (p), the radial stress across the thickness of a cylinder is a) maximum at the outer surface and minimum at the inner surface b) maximum at the inner surface and minimum at the outer surface c) maximum at the inner surface and zero at the outer surface d) maximum at the outer surface and zero at the inner surface

Description : In a thick cylindrical shell subjected to an internal pressure (p), the radial stress across the thickness of a cylinder is a) maximum at the outer surface and minimum at the inner surface b) maximum ... and zero at the outer surface d) maximum at the outer surface and zero at the inner surface

Last Answer : c) maximum at the inner surface and zero at the outer surface

Which one of the following parts of a ball bearing acts as a barrier between the balls preventing them from bumping into each other? (a) Inner race (b) Outer race (c) Rolling element (d) Cage

Description : Which one of the following parts of a ball bearing acts as a barrier between the balls preventing them from bumping into each other? (a) Inner race (b) Outer race (c) Rolling element (d) Cage

Last Answer : (d) Cage

Which one of the following parts of a ball bearing is mounted to the housing and is stationary? (a) Inner race (b) Outer race (c) Rolling element (d) Cage

Description : Which one of the following parts of a ball bearing is mounted to the housing and is stationary? (a) Inner race (b) Outer race (c) Rolling element (d) Cage

Last Answer : (b) Outer race

Which one of the following parts of a ball bearing is mounted on the rotating shafts and tends to rotate the shaft? (a) Inner race (b) Outer race (c) Rolling element (d) Cage

Description : Which one of the following parts of a ball bearing is mounted on the rotating shafts and tends to rotate the shaft? (a) Inner race (b) Outer race (c) Rolling element (d) Cage

Last Answer : (a) Inner race

A washer is specified by (A) Outer diameter (B) Inner diameter (C) Thickness (D) Mean diameter

Description : A washer is specified by (A) Outer diameter (B) Inner diameter (C) Thickness (D) Mean diameter

Last Answer : (B) Inner diameter

Parallel fillet weld and transverse fillet weld both have the plane in which maximum shear stress occurs at 45’ to the leg dimension. a) True b) False

Description : Parallel fillet weld and transverse fillet weld both have the plane in which maximum shear stress occurs at 45’ to the leg dimension. a) True b) False

Last Answer : b) False

Among maximum shear stress theory and distortion energy theory, which gives the higher value shear yield strength? a) Maximum shear stress theory b) Distortion energy theory c) Both give equal values d) Vary from material to material

Description : Among maximum shear stress theory and distortion energy theory, which gives the higher value shear yield strength? a) Maximum shear stress theory b) Distortion energy theory c) Both give equal values d) Vary from material to material

Last Answer : b) Distortion energy theory

Maximum shear stress in transverse fillet weld of leg h and length l is a) P/hl b) 1.21P/hl c) P/1.21hl d) None of the listed

Description : Maximum shear stress in transverse fillet weld of leg h and length l is a) P/hl b) 1.21P/hl c) P/1.21hl d) None of the listed

Last Answer : b) 1.21P/hl

According to the ASME code, maximum allowable shear stress is taken as X% of yield strength or Y% of ultimate strength. a) X=30 Y=18 b) X=30 Y=30 c) X=18 Y=18 d) X=18 Y=30

Description : According to the ASME code, maximum allowable shear stress is taken as X% of yield strength or Y% of ultimate strength. a) X=30 Y=18 b) X=30 Y=30 c) X=18 Y=18 d) X=18 Y=30

Last Answer : a) X=30 Y=18

Maximum shear stress in transverse fillet weld of leg h and length l is a) P/hl b) 1.21P/hl c) P/1.21hl d) None of the listed

Description : Maximum shear stress in transverse fillet weld of leg h and length l is a) P/hl b) 1.21P/hl c) P/1.21hl d) None of the listed

Last Answer : b) 1.21P/hl

According to the ASME code, maximum allowable shear stress is taken as X% of yield strength or Y% of ultimate strength. a) X=30 Y=18 b) X=30 Y=30 c) X=18 Y=18 d) X=18 Y=30

Description : According to the ASME code, maximum allowable shear stress is taken as X% of yield strength or Y% of ultimate strength. a) X=30 Y=18 b) X=30 Y=30 c) X=18 Y=18 d) X=18 Y=30

Last Answer : a) X=30 Y=18

Maximum shear stress theory is used for (A) Cast iron shafts (B) Steel shafts (C) Flexible shafts (D) Plastic shafts

Description : Maximum shear stress theory is used for (A) Cast iron shafts (B) Steel shafts (C) Flexible shafts (D) Plastic shafts

Last Answer : (B) Steel shafts

A transmission shaft subjected to pure bending moment should be designed on the basis of (A) Maximum principal stress theory (B) Maximum shear stress theory (C) Distortion energy theory (D) Goodman or Soderberg diagrams

Description : A transmission shaft subjected to pure bending moment should be designed on the basis of (A) Maximum principal stress theory (B) Maximum shear stress theory (C) Distortion energy theory (D) Goodman or Soderberg diagrams

Last Answer : (A) Maximum principal stress theory

Among maximum shear stress theory and distortion energy theory, which gives the higher value shear yield strength? a) Maximum shear stress theory b) Distortion energy theory c) Both give equal values d) Vary from material to material

Description : Among maximum shear stress theory and distortion energy theory, which gives the higher value shear yield strength? a) Maximum shear stress theory b) Distortion energy theory c) Both give equal values d) Vary from material to material

Last Answer : b) Distortion energy theory

For a homogeneous & isotropic body under hydrostatic pressure, which theory of elastic failure does not fail (a) Firstly Maximum Principal Theory (b) Secondly Maximum Shear Stress Theory (c) Thirdly Maximum Principal Energy Theory (d) None

Description : For a homogeneous & isotropic body under hydrostatic pressure, which theory of elastic failure does not fail (a) Firstly Maximum Principal Theory (b) Secondly Maximum Shear Stress Theory (c) Thirdly Maximum Principal Energy Theory (d) None

Last Answer : (a) Firstly Maximum Principal Theory

Under complex loading, if elastic limit reaches in tension, then failure occurs due to (a) Firstly Maximum principal strain theory (b) Secondly Maximum principal theory of strain energy (c) Thirdly Maximum shear stress theory (d) None

Description : Under complex loading, if elastic limit reaches in tension, then failure occurs due to (a) Firstly Maximum principal strain theory (b) Secondly Maximum principal theory of strain energy (c) Thirdly Maximum shear stress theory (d) None

Last Answer : (d) None

A ductile material may not meet a failure if it has been tested for the theories of failure (a) Firstly Maximum Shear Stress Theory (b) Secondly Maximum Shear Strain Energy Theory (c) Both (a) & (b) (d) None

Description : A ductile material may not meet a failure if it has been tested for the theories of failure (a) Firstly Maximum Shear Stress Theory (b) Secondly Maximum Shear Strain Energy Theory (c) Both (a) & (b) (d) None

Last Answer : (c) Both (a) & (b)

Maximum shear stress is equal to (a) (σ1 –σ2)/2 (b) (σ1 + σ2)/2 (c) (σ1 + 2σ2)/2 (d) None

Description : Maximum shear stress is equal to (a) (σ1 –σ2)/2 (b) (σ1 + σ2)/2 (c) (σ1 + 2σ2)/2 (d) None

Last Answer : (a) (σ1 –σ2)/2

Under maximum shear stress theory, maximum shear stress is equal to (a) Allowable stress in tension (b) Allowable stress in compression (c) Allowable stress in shear (d) None

Description : Under maximum shear stress theory, maximum shear stress is equal to (a) Allowable stress in tension (b) Allowable stress in compression (c) Allowable stress in shear (d) None

Last Answer : (c) Allowable stress in shear