For a helical torsion sprig, the stress concentration factor at outer fibre is? Give spring index=5. a) 0.78 b) 0.87 c) 1.87 d) 0.69

For a helical torsion sprig, the stress concentration factor at outer fibre is? Give spring index=5.

a) 0.78

b) 0.87

c) 1.87

d) 0.69
by

1 Answer

Answer :

b) 0.87
by

Related questions

For a helical torsion sprig, the stress concentration factor at inner fibre is? Give spring index=5. a) 1.005 b) 1.175 c) 1.223 d) 1.545

Description : For a helical torsion sprig, the stress concentration factor at inner fibre is? Give spring index=5. a) 1.005 b) 1.175 c) 1.223 d) 1.545

Last Answer : b) 1.175

Find the shear stress in the spring wire used to design a helical compression sprig if a load of 1200N is applied on the spring. Spring index is 6, and wire diameter 7mm. a) 452.2N/mm² b) 468.6N/mm² c) 512.2N/mm² d) None of the listed

Description : Find the shear stress in the spring wire used to design a helical compression sprig if a load of 1200N is applied on the spring. Spring index is 6, and wire diameter 7mm. a) 452.2N/mm² b) 468.6N/mm² c) 512.2N/mm² d) None of the listed

Last Answer : b) 468.6N/mm²

When the helical torsion spring is subjected to torque, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress

Description : When the helical torsion spring is subjected to torque, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress

Last Answer : (C) Bending stress

Helical torsion spring is used in (A) door hinges (B) door closers (C) automobile starters (D) all of the above

Description : Helical torsion spring is used in (A) door hinges (B) door closers (C) automobile starters (D) all of the above

Last Answer : (D) all of the above

The type of spring used to absorb and release energy in mechanical watches is (A) Helical extension spring (B) Multi-leaf spring (C) Spiral spring (D) Helical torsion spring

Description : The type of spring used to absorb and release energy in mechanical watches is (A) Helical extension spring (B) Multi-leaf spring (C) Spiral spring (D) Helical torsion spring

Last Answer : (C) Spiral spring

The type of spring used in vehicle clutches is, (A) Helical compression spring (B) Belleville spring (C) Both (A) and (B) (D) Helical torsion spring

Description : The type of spring used in vehicle clutches is, (A) Helical compression spring (B) Belleville spring (C) Both (A) and (B) (D) Helical torsion spring

Last Answer : (C) Both (A) and (B)

The type of spring used in door hinges is, (A) Helical extension spring (B) Multi-leaf spring (C) Spiral spring (D) Helical torsion spring

Description : The type of spring used in door hinges is, (A) Helical extension spring (B) Multi-leaf spring (C) Spiral spring (D) Helical torsion spring

Last Answer : (D) Helical torsion spring

The helical spring ad wire of helical torsion spring, both are subjected to torsional shear stresses. a) True b) False

Description : The helical spring ad wire of helical torsion spring, both are subjected to torsional shear stresses. a) True b) False

Last Answer : b) False

Wahl factor to account for direct shear stress and stress concentration due to curvature for helical springs is given by, (A) (4C - 1/4C - 4) + 0.615/C (B) (4C - 1/4C + 4) + 0.615/C (C) (4C + 1/4C - 4) + 0.615/C (D) (4C + 1/4C + 4) + 0.615/C

Description : Wahl factor to account for direct shear stress and stress concentration due to curvature for helical springs is given by, (A) (4C - 1/4C - 4) + 0.615/C (B) (4C - 1/4C + 4) + 0.615/C (C) (4C + 1/4C - 4) + 0.615/C (D) (4C + 1/4C + 4) + 0.615/C

Last Answer : (A) (4C - 1/4C - 4) + 0.615/C

When the helical compression spring is subjected to axial compressive force, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress

Description : When the helical compression spring is subjected to axial compressive force, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress

Last Answer : (D) Torsional shear stress

When the helical extension spring is subjected to axial tensile force, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress

Description : When the helical extension spring is subjected to axial tensile force, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress

Last Answer : (D) Torsional shear stress

The maximum shear stress in spring wire is induced at (A) Inner surface of the coil (B) Outer surface of the coil (C) Central surface of the coil (D) End coils

Description : The maximum shear stress in spring wire is induced at (A) Inner surface of the coil (B) Outer surface of the coil (C) Central surface of the coil (D) End coils

Last Answer : (A) Inner surface of the coil

The type of spring used to achieve any linear or non-linear load-deflection characteristic is (A) Spiral spring (B) Non-ferrous spring (C) Belleville (coned disk) spring (D) Torsion spring

Description : The type of spring used to achieve any linear or non-linear load-deflection characteristic is (A) Spiral spring (B) Non-ferrous spring (C) Belleville (coned disk) spring (D) Torsion spring

Last Answer : (C) Belleville (coned disk) spring

When a close-coiled helical spring is subjected to an axial load, it is said to be under. (a) Bending (b) Shear (c) Torsion (d) Crushing

Description : When a close-coiled helical spring is subjected to an axial load, it is said to be under. (a) Bending (b) Shear (c) Torsion (d) Crushing

Last Answer : (c) Torsion

A concentric spring consist of two helical compression springs (A) both springs always have right hand helix (B) both springs always have left hand helix (C) both springs always have opposite hand of helices (D) any of the above

Description : A concentric spring consist of two helical compression springs (A) both springs always have right hand helix (B) both springs always have left hand helix (C) both springs always have opposite hand of helices (D) any of the above

Last Answer : (C) both springs always have opposite hand of helices

Axial length of an unloaded helical compression spring is called (A) compressed length (B) solid length (C) free length (D) none of the above

Description : Axial length of an unloaded helical compression spring is called (A) compressed length (B) solid length (C) free length (D) none of the above

Last Answer : (C) free length

The helix angle in case of closely coiled helical spring is (A) less than 5° (B) 5° to 7° (C) 7° to 10° (D) more than 10°

Description : The helix angle in case of closely coiled helical spring is (A) less than 5° (B) 5° to 7° (C) 7° to 10° (D) more than 10°

Last Answer : (D) more than 10°

The helix angle in case of closely coiled helical spring is (A) less than 10° (B) 10° to 15° (C) 15° to 20° (D) more than 20°

Description : The helix angle in case of closely coiled helical spring is (A) less than 10° (B) 10° to 15° (C) 15° to 20° (D) more than 20°

Last Answer : (A) less than 10°

The type of spring used to measure weights in spring balance is, (A) Helical extension spring (B) Multi-leaf spring (C) Spiral spring

Description : The type of spring used to measure weights in spring balance is, (A) Helical extension spring (B) Multi-leaf spring (C) Spiral spring

Last Answer : (A) Helical extension spring

When a helical spring is cut into two halves, the stiffness of each half spring will be, (A) Same as original spring (B) Double of original spring (C) Half of original spring (D) One fourth of original spring

Description : When a helical spring is cut into two halves, the stiffness of each half spring will be, (A) Same as original spring (B) Double of original spring (C) Half of original spring (D) One fourth of original spring

Last Answer : (B) Double of original spring

The type of spring used to absorb shocks and vibrations in vehicles is, (A) Helical extension spring (B) Multi-leaf spring (C) Spiral spring (D) Belleville (coned disk) spring

Description : The type of spring used to absorb shocks and vibrations in vehicles is, (A) Helical extension spring (B) Multi-leaf spring (C) Spiral spring (D) Belleville (coned disk) spring

Last Answer : (B) Multi-leaf spring

Calculate fatigue stress concentration factor, when theoretical stress concentration factor is 1.62 and notch sensitivity is equal to 0.9 a. 1.558 b. 3.358 c. 1.162 d. None of the above

Description : Calculate fatigue stress concentration factor, when theoretical stress concentration factor is 1.62 and notch sensitivity is equal to 0.9 a. 1.558 b. 3.358 c. 1.162 d. None of the above

Last Answer : a. 1.558

Find the Wahl’s factor if spring index is 6. a) 1.2020 b) 1.2424 c) 1.2525 d) 1.5252

Description : Find the Wahl’s factor if spring index is 6. a) 1.2020 b) 1.2424 c) 1.2525 d) 1.5252

Last Answer : c) 1.2525

Notch sensitivity (q) is given by the equation _______ where K f = fatigue stress concentration factor and K t = theoretical stress concentration factor a. ( K f + 1 ) / ( K t – 1 ) b. ( K f – 1 ) / ( K t – 1 ) c. ( K f + 1 ) / ( K t + 1 ) d. ( K f - 1 ) / ( K t + 1 )

Description : Notch sensitivity (q) is given by the equation _______ where K f = fatigue stress concentration factor and K t = theoretical stress concentration factor a. ( K f + 1 ) / ( K t – 1 ) b. ( K f – 1 ) / ( K t – 1 ) c. ( K f + 1 ) / ( K t + 1 ) d. ( K f - 1 ) / ( K t + 1 )

Last Answer : b. ( K f – 1 ) / ( K t – 1 )

In which of the following case stress concentration factor is ignored? a) Ductile material under static load b) Ductile material under fluctuating load c) Brittle material under static load

Description : In which of the following case stress concentration factor is ignored? a) Ductile material under static load b) Ductile material under fluctuating load c) Brittle material under static load

Last Answer : a) Ductile material under static load

For an elliptical hole on a flat plate, if width of the hole in direction of the load decrease, Stress Concentration Factor will______ a) Increase b) Decrease c) Remains constant d) Can’t be determined. Varies from material to material

Description : For an elliptical hole on a flat plate, if width of the hole in direction of the load decrease, Stress Concentration Factor will______ a) Increase b) Decrease c) Remains constant d) Can’t be determined. Varies from material to material

Last Answer : a) Increase

If a flat plate with a circular hole is subjected to tensile force, then its theoretical stress concentration factor is? a) 2 b) 3 c) 4 d) 1

Description : If a flat plate with a circular hole is subjected to tensile force, then its theoretical stress concentration factor is? a) 2 b) 3 c) 4 d) 1

Last Answer : b) 3

Stress Concentration Factor is the ratio of nominal stress obtained by elementary equations for minimum cross- section and highest value of actual stress near discontinuity. a) True b) False

Description : Stress Concentration Factor is the ratio of nominal stress obtained by elementary equations for minimum cross- section and highest value of actual stress near discontinuity. a) True b) False

Last Answer : b) False

The notch sensitivity q is expressed in terms of fatigue stress concentration factor Kf and theoretical stress concentration factor Kt as (A) (Kf + 1)/ (Kt + 1) (B) (Kf - 1)/ (Kt - 1) (C) (Kt + 1)/ (Kf + 1) (D) (Kt - 1)/ (Kf - 1)

Description : The notch sensitivity q is expressed in terms of fatigue stress concentration factor Kf and theoretical stress concentration factor Kt as (A) (Kf + 1)/ (Kt + 1) (B) (Kf - 1)/ (Kt - 1) (C) (Kt + 1)/ (Kf + 1) (D) (Kt - 1)/ (Kf - 1)

Last Answer : (B) (Kf - 1)/ (Kt - 1)

If spring index=2.5, what can be concluded about stresses in the wire? a) They are high b) They are negligible c) They are moderate d) Cannot be determined

Description : If spring index=2.5, what can be concluded about stresses in the wire? a) They are high b) They are negligible c) They are moderate d) Cannot be determined

Last Answer : a) They are high

A spring index from ___ is considered as best for manufacturing considerations. (A) 4 to 12 (B) 12 to 20 (C) 20 to 28 (D) 28 to 36

Description : A spring index from ___ is considered as best for manufacturing considerations. (A) 4 to 12 (B) 12 to 20 (C) 20 to 28 (D) 28 to 36

Last Answer : (A) 4 to 12

The spring index indicates the relative sharpness of the ___ of the coil. (A) length (B) curvature (C) thickness (D) none of the above

Description : The spring index indicates the relative sharpness of the ___ of the coil. (A) length (B) curvature (C) thickness (D) none of the above

Last Answer : (B) curvature

The spring index (C) is (A) mean coil diameter / wire diameter (B) wire diameter / mean coil diameter (C) wire diameter x mean coil diameter (D) none of the above

Description : The spring index (C) is (A) mean coil diameter / wire diameter (B) wire diameter / mean coil diameter (C) wire diameter x mean coil diameter (D) none of the above

Last Answer : (A) mean coil diameter / wire diameter

The spring index is, (A) Ratio of wire diameter to mean coil diameter (B) Force per unit cross-sectional area of spring (C) Ratio of mean coil diameter to wire diameter (D) Force required to produce unit deflection

Description : The spring index is, (A) Ratio of wire diameter to mean coil diameter (B) Force per unit cross-sectional area of spring (C) Ratio of mean coil diameter to wire diameter (D) Force required to produce unit deflection

Last Answer : (C) Ratio of mean coil diameter to wire diameter

When two concentric springs are made of same material, having same free length and compressed equally by axial load, then the load shared by each spring is proportional to (A) Spring index of each spring (B) Wire diameter of each spring (C) Mean coil diameter of each spring (D) Square of wire diameter of each spring

Description : When two concentric springs are made of same material, having same free length and compressed equally by axial load, then the load shared by each spring is proportional to (A) Spring index of each spring ... spring (C) Mean coil diameter of each spring (D) Square of wire diameter of each spring

Last Answer : (D) Square of wire diameter of each spring

A spring with index=15 is prone to buckling. a) True b) False

Description : A spring with index=15 is prone to buckling. a) True b) False

Last Answer : a) True

The spring index is the ratio of wire diameter to mean coil diameter. a) True b) False

Description : The spring index is the ratio of wire diameter to mean coil diameter. a) True b) False

Last Answer : a) True

Transverse fillet welds are under (i) Bending and shear stresses (ii)Compressive and torsion shear stresses (iii)Tensile and compressive stresses (iv)None

Description : Transverse fillet welds are under (i) Bending and shear stresses (ii)Compressive and torsion shear stresses (iii)Tensile and compressive stresses (iv)None

Last Answer : (iv)None

Parallel fillet welds are under  Shear and bending stresses  Compressive and torsion shear stresses  Tensile and compressive stresses  None

Description : Parallel fillet welds are under  Shear and bending stresses  Compressive and torsion shear stresses  Tensile and compressive stresses  None

Last Answer :  None

Flexible shafts have _______ rigidity in torsion making them flexible. a) Low b) High c) Very high d) Infinitely small

Description : Flexible shafts have _______ rigidity in torsion making them flexible. a) Low b) High c) Very high d) Infinitely small

Last Answer : b) High

Determine number of coils in a helical compression spring, if modulus of rigidity is 80 Gpa and spring stiffness is 50 N/ mm. Assume wire diameter and spring index as 8 mm and 5 respectively a. 11.8 turns b. 12.8 turns c. 13.3 turns d. None of the above

Description : Determine number of coils in a helical compression spring, if modulus of rigidity is 80 Gpa and spring stiffness is 50 N/ mm. Assume wire diameter and spring index as 8 mm and 5 respectively a. 11.8 turns b. 12.8 turns c. 13.3 turns d. None of the above

Last Answer : b. 12.8 turns

-The method used to induce a layer of residual compressive stress on the surface of the spring wire, is (A) shot peening (B) burnishing (C) lapping (D) none of the above

Description : -The method used to induce a layer of residual compressive stress on the surface of the spring wire, is (A) shot peening (B) burnishing (C) lapping (D) none of the above

Last Answer : (A) shot peening

What will happen if stresses induced due to surge in the spring exceeds the endurance limit stress of the spring. a) Fatigue Failure b) Fracture c) None of the listed d) Nipping

Description : What will happen if stresses induced due to surge in the spring exceeds the endurance limit stress of the spring. a) Fatigue Failure b) Fracture c) None of the listed d) Nipping

Last Answer : a) Fatigue Failure

Keyed joints never lead to stress concentration on shafts. a) True b) False

Description : Keyed joints never lead to stress concentration on shafts. a) True b) False

Last Answer : b) False

The keyway, (A) Reduces strength of shaft (B) Reduces rigidity of shaft (C) Increases stress concentration (D) All of above

Description : The keyway, (A) Reduces strength of shaft (B) Reduces rigidity of shaft (C) Increases stress concentration (D) All of above

Last Answer : (D) All of above

Stress concentration is caused due to A. Variation in properties of material from point to point in a member B. Pitting at points or areas at which loads on a member are applied C. Abrupt change of section D. All of the above

Description : Stress concentration is caused due to A. Variation in properties of material from point to point in a member B. Pitting at points or areas at which loads on a member are applied C. Abrupt change of section D. All of the above

Last Answer : D. All of the above

Which of the following reduces the stress concentration? a) Use of multiple notches b) Drilling additional holes c) Removal of undesired material d) Each of the mentioned

Description : Which of the following reduces the stress concentration? a) Use of multiple notches b) Drilling additional holes c) Removal of undesired material d) Each of the mentioned

Last Answer : d) Each of the mentioned

Use of multiple notches in a V shaped flat plate will a) Reduce the stress concentration b) Increase the stress concentration c) No effect d) Cannot be determined

Description : Use of multiple notches in a V shaped flat plate will a) Reduce the stress concentration b) Increase the stress concentration c) No effect d) Cannot be determined

Last Answer : a) Reduce the stress concentration

Is it logical to use fluid analogy to understand the phenomenon of stress concentration? a) True b) False

Description : Is it logical to use fluid analogy to understand the phenomenon of stress concentration? a) True b) False

Last Answer : a) True

Stress concentration is defined as the localization of high stresses due to irregularities present in the component and no changes of the cross section. a) True b) False

Description : Stress concentration is defined as the localization of high stresses due to irregularities present in the component and no changes of the cross section. a) True b) False

Last Answer : b) False