Which one of the following parts of a ball bearing is mounted on the rotating shafts and tends to rotate the shaft? (a) Inner race (b) Outer race (c) Rolling element (d) Cage

Which one of the following parts of a ball bearing is mounted on the rotating shafts and tends to rotate the shaft?

(a) Inner race

(b) Outer race

(c) Rolling element

(d) Cage
by

1 Answer

Answer :

(a) Inner race
by

Related questions

Which one of the following parts of a ball bearing is mounted to the housing and is stationary? (a) Inner race (b) Outer race (c) Rolling element (d) Cage

Description : Which one of the following parts of a ball bearing is mounted to the housing and is stationary? (a) Inner race (b) Outer race (c) Rolling element (d) Cage

Last Answer : (b) Outer race

Which one of the following parts of a ball bearing acts as a barrier between the balls preventing them from bumping into each other? (a) Inner race (b) Outer race (c) Rolling element (d) Cage

Description : Which one of the following parts of a ball bearing acts as a barrier between the balls preventing them from bumping into each other? (a) Inner race (b) Outer race (c) Rolling element (d) Cage

Last Answer : (d) Cage

In hydrodynamic bearing, when the shaft begins to rotate in clockwise direction, (A) The journal climbs to the right side of the bearing without metal to metal contact (B) The journal climbs to the left side of the bearing without metal to metal contact (C) The journal sinks down to the bottom of the bearing (D) The journal is at the center of the bearing

Description : In hydrodynamic bearing, when the shaft begins to rotate in clockwise direction, (A) The journal climbs to the right side of the bearing without metal to metal contact (B) The journal climbs to the left ... sinks down to the bottom of the bearing (D) The journal is at the center of the bearing

Last Answer : (A) The journal climbs to the right side of the bearing without metal to metal contact

Calculate the bearing life if expected life for 90% bearings is 9000 hr and the shaft is rotating at 1500 rpm. (a) 850 million rev (b) 810 million rev (c) 810 hr (d) 850 hr

Description : Calculate the bearing life if expected life for 90% bearings is 9000 hr and the shaft is rotating at 1500 rpm. (a) 850 million rev (b) 810 million rev (c) 810 hr (d) 850 hr

Last Answer : (b) 810 million rev

The static load is defined as the load acting on the bearing when the shaft is _____. (a) stationary (b) rotating at rpm<5 (c) rotating at rpm<10 (d) rotating at rpm<15

Description : The static load is defined as the load acting on the bearing when the shaft is _____. (a) stationary (b) rotating at rpm

Last Answer : (a) stationary

Static load is defined as the load acting on the bearing when shaft is _____ a) Stationary b) Rotating at rpm<10 c) Rotating at rpm<5 d) None of the listed

Description : Static load is defined as the load acting on the bearing when shaft is _____ a) Stationary b) Rotating at rpm

Last Answer : a) Stationary

Which bearing is Antifriction bearing A. Thick lubrication bearing B. Thin lubrication bearing C. Rolling or ball bearing D. None

Description : Which bearing is Antifriction bearing A. Thick lubrication bearing B. Thin lubrication bearing C. Rolling or ball bearing D. None

Last Answer : C. Rolling or ball bearing

Shaft is rotating machine element. A. True B. False

Description : Shaft is rotating machine element. A. True B. False

Last Answer : A. True

The ball bearing is subjected to a radial load of 4000 N. Expected life for 90% bearings is 9000 hr and the shaft is rot (a) 42.21 kN (b) 37.29 kN (c) 26.33 kN (d) 35.22 kN

Description : The ball bearing is subjected to a radial load of 4000 N. Expected life for 90% bearings is 9000 hr and the shaft is rot (a) 42.21 kN (b) 37.29 kN (c) 26.33 kN (d) 35.22 kN

Last Answer : (b) 37.29 kN

A knuckle joint is unsuitable for two rotating shafts, which transmit torque a) True b) False

Description : A knuckle joint is unsuitable for two rotating shafts, which transmit torque a) True b) False

Last Answer : a) True

A coupling is a mechanical device that temporarily joins two rotating shafts to each other. a) True b) False

Description : A coupling is a mechanical device that temporarily joins two rotating shafts to each other. a) True b) False

Last Answer : b) False

A bushed-pin type flange coupling is used (A) For intersecting shafts (B) When the shafts are not in exact alignment (C) For small shafts rotating at slow speeds (D) For parallel shafts

Description : A bushed-pin type flange coupling is used (A) For intersecting shafts (B) When the shafts are not in exact alignment (C) For small shafts rotating at slow speeds (D) For parallel shafts

Last Answer : (B) When the shafts are not in exact alignment

A coupling is a mechanical device that temporarily joins two rotating shafts to each other. a) True b) False

Description : A coupling is a mechanical device that temporarily joins two rotating shafts to each other. a) True b) False

Last Answer : b) False

Rotating shafts tends to vibrate violently in transverse directions at certain speed. This speed is called A Critical speedB Whipping speed C Whirling speed D All of the mentioned

Description : Rotating shafts tends to vibrate violently in transverse directions at certain speed. This speed is called A Critical speedB Whipping speed C Whirling speed D All of the mentioned

Last Answer : D All of the mentioned

A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and height of the key being 14mm and 80mm respectively. Find the compressive stress induced in the key. a) 70.1 N/mm2 b) 51.6N/mm2 c) 45.5N/mm2 d) None of the listed

Description : A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and height of the key being 14mm and 80mm respectively. Find the compressive stress induced in the key. a) 70.1 N/mm2 b) 51.6N/mm2 c) 45.5N/mm2 d) None of the listed

Last Answer : b) 51.6N/mm2

A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and breadth of the key being 14mm and 80mm respectively. Find the shear stress induced in the key. a) 30.2N/mm2 b) 25.8N/mm2 c) 34.4N/mm2 d) None of the listed

Description : A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and breadth of the key being 14mm and 80mm respectively. Find the shear stress induced in the key. a) 30.2N/mm2 b) 25.8N/mm2 c) 34.4N/mm2 d) None of the listed

Last Answer : b) 25.8N/mm2

Two shafts A and B are made of same material. The diameter of shaft A is twice that of B. The torque transmitted by shaft A will be (A) Twice that of B (B) Four times that of B (C) Eight times that of B (D) Sixteen times that of B

Description : Two shafts A and B are made of same material. The diameter of shaft A is twice that of B. The torque transmitted by shaft A will be (A) Twice that of B (B) Four times that of B (C) Eight times that of B (D) Sixteen times that of B

Last Answer : (C) Eight times that of B

Two shafts A and B are made of same material. The diameters of shaft A and B are dA and dB respectively. The ratio of torque transmitted by shaft A to that of shaft B will be (A) dA/dB- (B) (dA/dB-)2 (C) (dA/dB-)3 (D) (dA/dB-)4

Description : Two shafts A and B are made of same material. The diameters of shaft A and B are dA and dB respectively. The ratio of torque transmitted by shaft A to that of shaft B will be (A) dA/dB- (B) (dA/dB-)2 (C) (dA/dB-)3 (D) (dA/dB-)4

Last Answer : (C) (dA/dB-)3

A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and breadth of the key being 14mm and 80mm respectively. Find the shear stress induced in the key. a) 30.2N/mm2 b) 25.8N/mm2 c) 34.4N/mm2 d) None of the listed

Description : A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and breadth of the key being 14mm and 80mm respectively. Find the shear stress induced in the key. a) 30.2N/mm2 b) 25.8N/mm2 c) 34.4N/mm2 d) None of the listed

Last Answer : b) 25.8N/mm2

The angular play bearing must be mounted without axial play. (a) Yes (b) Little tolerance is adjusted

Description : The angular play bearing must be mounted without axial play. (a) Yes (b) Little tolerance is adjusted

Last Answer : (a) Yes

The angular play bearing must be mounted without axial play. a) Yes b) Little tolerance is adjusted c) Little tolerance is necessary d) Can’t be stated

Description : The angular play bearing must be mounted without axial play. a) Yes b) Little tolerance is adjusted c) Little tolerance is necessary d) Can’t be stated

Last Answer : a) Yes

Deep groove ball bearings are used for (a) heavy thrust load only (b) the small angular displacement of shafts (c) radial load at high speed (d) combined thrust and radial loads at high speed

Description : Deep groove ball bearings are used for (a) heavy thrust load only (b) the small angular displacement of shafts (c) radial load at high speed (d) combined thrust and radial loads at high speed

Last Answer : (d) combined thrust and radial loads at high speed

The rolling contact bearings as compared to sliding contact bearings have (a) small overall dimensions (b) accuracy of shaft alignment (c) low starting and low running friction except at very high speeds (d) all the mentioned

Description : The rolling contact bearings as compared to sliding contact bearings have (a) small overall dimensions (b) accuracy of shaft alignment (c) low starting and low running friction except at very high speeds (d) all the mentioned

Last Answer : (d) all the mentioned

Hot rolling produces a stronger shaft then cold rolling. a) True b) False

Description : Hot rolling produces a stronger shaft then cold rolling. a) True b) False

Last Answer : b) False

Hot rolling produces a stronger shaft then cold rolling. a) True b) False

Description : Hot rolling produces a stronger shaft then cold rolling. a) True b) False

Last Answer : b) False

______ is used for a shaft that supports rotating elements like wheels, drums or rope sleaves. a) Spindle b) Axle c) Shaf d) None of the listed

Description : ______ is used for a shaft that supports rotating elements like wheels, drums or rope sleaves. a) Spindle b) Axle c) Shaf d) None of the listed

Last Answer : a) Spindle

______ is used for a shaft that supports rotating elements like wheels, drums or rope sleaves. a) Spindle b) Axle c) Shaf d) None of the listed

Description : ______ is used for a shaft that supports rotating elements like wheels, drums or rope sleaves. a) Spindle b) Axle c) Shaf d) None of the listed

Last Answer : a) Spindle

In a flail harvester, the cutting operation is performed by a) Horizontally rotating circular blades b) Vertically rotating circular blades c) Knives mounted on a horizontal shaft d) Knives mounted on a vertical shaft Ans. c

Description : In a flail harvester, the cutting operation is performed by a) Horizontally rotating circular blades b) Vertically rotating circular blades c) Knives mounted on a horizontal shaft d) Knives mounted on a vertical shaft Ans. c

Last Answer : ans c

is a harrow which perform harrow operation by means of set or a number of sets of rotating slat each set being mounted on common shaft. a. Spike tooth harrow c. Triangular harrow b. Acme harrow. d. Disc harrow

Description : is a harrow which perform harrow operation by means of set or a number of sets of rotating slat each set being mounted on common shaft. a. Spike tooth harrow c. Triangular harrow b. Acme harrow. d. Disc harrow

Last Answer :  Disc harrow

_______is suitable as a lubricant for heavy-duty applications of rolling contact bearing. (a) Grease (b) Lubricating oil (c) Graphite (d) Air

Description : _______is suitable as a lubricant for heavy-duty applications of rolling contact bearing. (a) Grease (b) Lubricating oil (c) Graphite (d) Air

Last Answer : (b) Lubricating oil

________is suitable as a lubricant for low and moderate loads applications of rolling contact bearing. (a) Grease (b) Lubricating oil (c) Graphite (d) Air

Description : ________is suitable as a lubricant for low and moderate loads applications of rolling contact bearing. (a) Grease (b) Lubricating oil (c) Graphite (d) Air

Last Answer : (a) Grease

An antifriction bearing consists of (a) rolling elements (b) races (c) cages (d) all of the listed

Description : An antifriction bearing consists of (a) rolling elements (b) races (c) cages (d) all of the listed

Last Answer : (d) all of the listed

A rolling contact bearing is specified as X307. Calculate the bearing diameter. (a) 35 mm (b) 28 mm (c) 21 mm (d) 7 mm

Description : A rolling contact bearing is specified as X307. Calculate the bearing diameter. (a) 35 mm (b) 28 mm (c) 21 mm (d) 7 mm

Last Answer : (a) 35 mm

Rolling contact bearing is also called as A. Plastic bearing B. Thin lubrication bearing C. Thick lubrication bearing D. Antifriction bearing.

Description : Rolling contact bearing is also called as A. Plastic bearing B. Thin lubrication bearing C. Thick lubrication bearing D. Antifriction bearing.

Last Answer : D. Antifriction bearing.

The listed life of a rolling bearing, in a catalog is the, (a) minimum expected life (b) maximum expected life (c) average life (d) none of the mentioned

Description : The listed life of a rolling bearing, in a catalog is the, (a) minimum expected life (b) maximum expected life (c) average life (d) none of the mentioned

Last Answer : (a) minimum expected life

A journal bearing is a ______ contact bearing working on the hydrodynamic lubrication and which supports load in____ direction. a) Sliding, Axial b) Rolling, Radial c) Sliding, Radial d) Rolling, Axial

Description : A journal bearing is a ______ contact bearing working on the hydrodynamic lubrication and which supports load in____ direction. a) Sliding, Axial b) Rolling, Radial c) Sliding, Radial d) Rolling, Axial

Last Answer : c) Sliding, Radial

A rolling contact bearing is specified as X307. Determine the series. a) Extra light series b) Light series c) Medium series d) Heavy series

Description : A rolling contact bearing is specified as X307. Determine the series. a) Extra light series b) Light series c) Medium series d) Heavy series

Last Answer : c) Medium series

Consider the following statements: [IES 2007] For a journal rotating in a bearing under film lubrication conditions, the frictional resistance is- 1. Proportional to the area of contact 2. Proportional to the viscosity of lubricant 3. Proportional to the speed of rotation 4. Independent of the pressure Which of the statements given above are correct? (a) 1, 2, 3 and 4 (b) 1 and 4 only (c) 2, 3 and 4 only (d) 2 and 3 only

Description : Consider the following statements: [IES 2007] For a journal rotating in a bearing under film lubrication conditions, the frictional resistance is- 1. Proportional to the area of contact 2. Proportional to the viscosity of lubricant 3. ... 4 (b) 1 and 4 only (c) 2, 3 and 4 only (d) 2 and 3 only

Last Answer : (a) 1, 2, 3 and 4

Assertion (A): In steady rotating condition the journal inside a hydrodynamic journal bearing remains floating on the oil film. [IES-2008] Reason (R): The hydrodynamic pressure developed in steady rotating conditions in journal bearings balances the load on the journal. (a) Both A and R are true and R is the correct explanation of A (b) Both A and R are true but R is NOT the correct explanation of A (c) A is true but R is false (d) A is false but R is true

Description : Assertion (A): In steady rotating condition the journal inside a hydrodynamic journal bearing remains floating on the oil film. [IES-2008] Reason (R): The hydrodynamic pressure developed in steady rotating conditions in journal ... A (c) A is true but R is false (d) A is false but R is true

Last Answer : (a) Both A and R are true and R is the correct explanation of A

Which of the following statements is/are true? A. Torsional vibrations do not occur in a three rotor system, if rotors rotate in same direction B. Shaft vibrates with maximum frequency when rotors rotate in same direction C. Zero node behavior is observed in rotors rotating in opposite direction D. All of the above

Description : Which of the following statements is/are true? A. Torsional vibrations do not occur in a three rotor system, if rotors rotate in same direction B. Shaft vibrates with maximum frequency when rotors ... C. Zero node behavior is observed in rotors rotating in opposite direction D. All of the above

Last Answer : A. Torsional vibrations do not occur in a three rotor system, if rotors rotate in same direction

Which of the following statements is/are true? A) Torsional vibrations do not occur in a three rotor system, if rotors rotate in same direction B) Shaft vibrates with maximum frequency when rotors rotate in same direction C) Zero node behavior is observed in rotors rotating in opposite direction D) All of the above

Description : Which of the following statements is/are true? A) Torsional vibrations do not occur in a three rotor system, if rotors rotate in same direction B) Shaft vibrates with maximum frequency when rotors ... C) Zero node behavior is observed in rotors rotating in opposite direction D) All of the above

Last Answer : A) Torsional vibrations do not occur in a three rotor system, if rotors rotate in same direction

Which of the following statements is/are true? a. Torsional vibrations do not occur in a three rotor system, if rotors rotate in same direction b. Shaft vibrates with maximum frequency when rotors rotate in same direction c. Zero node behavior is observed in rotors rotating in opposite direction d. All of the above

Description : Which of the following statements is/are true? a. Torsional vibrations do not occur in a three rotor system, if rotors rotate in same direction b. Shaft vibrates with maximum frequency when rotors ... c. Zero node behavior is observed in rotors rotating in opposite direction d. All of the above

Last Answer : a. Torsional vibrations do not occur in a three rotor system, if rotors rotate in same direction

The ball bearings are provided with a cage (a) to reduce friction (b) to facilitate slipping of balls (c) to prevent the lubricant from flowing out (d) to maintain the balls at a fixed distance apart

Description : The ball bearings are provided with a cage (a) to reduce friction (b) to facilitate slipping of balls (c) to prevent the lubricant from flowing out (d) to maintain the balls at a fixed distance apart

Last Answer : (d) to maintain the balls at a fixed distance apart

The maximum shear stress in spring wire is induced at (A) Inner surface of the coil (B) Outer surface of the coil (C) Central surface of the coil (D) End coils

Description : The maximum shear stress in spring wire is induced at (A) Inner surface of the coil (B) Outer surface of the coil (C) Central surface of the coil (D) End coils

Last Answer : (A) Inner surface of the coil

A washer is specified by (A) Outer diameter (B) Inner diameter (C) Thickness (D) Mean diameter

Description : A washer is specified by (A) Outer diameter (B) Inner diameter (C) Thickness (D) Mean diameter

Last Answer : (B) Inner diameter

Consider the following pairs of types of bearings and applications: 1. Partial Journal bearing................... Rail wagon axles 2. Full journal bearing ......................Diesel engine crank-shaft 3. Radial bearing ............................Combined radial and axial loads Which of these pairs is/are correctly matched? [IES-2000] (a) 1 alone (b) 1 and 2 (c) 2 and 3 (d) 1, 2 and 3

Description : Consider the following pairs of types of bearings and applications: 1. Partial Journal bearing................... Rail wagon axles 2. Full journal bearing ......................Diesel engine crank-shaft 3. Radial bearing ... matched? [IES-2000] (a) 1 alone (b) 1 and 2 (c) 2 and 3 (d) 1, 2 and 3

Last Answer : (b) 1 and 2

Which one of the following sets of parameters should be monitored for determining safe operation of journal bearing? [IES-2000] Oil pressure, bearing metal temperature and bearing vibration (b) Bearing vibration, oil pressure and speed of shaft (c) Bearing metal temperature and oil pressure (d) Oil pressure and bearing vibration

Description : Which one of the following sets of parameters should be monitored for determining safe operation of journal bearing? [IES-2000] Oil pressure, bearing metal temperature and bearing vibration (b) ... shaft (c) Bearing metal temperature and oil pressure (d) Oil pressure and bearing vibration

Last Answer : Oil pressure, bearing metal temperature and bearing vibration

A full journal bearing having clearance to radius ratio of 1/100, using a lubricant with μ=28×10-3 Pa s supports the shaft journal running at N = 2400 rpm If bearing pressure is 1.4 MPa, the Somerfield number is [IES-2001] (a) 8×10-3 (b) 8×10-5 (c) 0.48 (d) 0.48×10

Description : A full journal bearing having clearance to radius ratio of 1/100, using a lubricant with μ=28×10-3 Pa s supports the shaft journal running at N = 2400 rpm If bearing pressure is 1.4 MPa, the Somerfield number is [IES-2001] (a) 8×10-3 (b) 8×10-5 (c) 0.48 (d) 0.48×10

Last Answer : (a) S = (μN s /p) (r/c) 2

Consider tile following statements: [IES-1993; 2002; 2006] Radius of friction circle for a journal bearing depends upon 1. Coefficient of friction 2. Radius of the journal 3. Angular speed of rotation of the shaft Which of the statements given above are correct? (a) 1,2 and 3 (b) Only 1 and 2 (c) Only 2 and 3 (d) Only 1 and 3

Description : Consider tile following statements: [IES-1993; 2002; 2006] Radius of friction circle for a journal bearing depends upon 1. Coefficient of friction 2. Radius of the journal 3. Angular speed of rotation of the shaft Which of the ... ) 1,2 and 3 (b) Only 1 and 2 (c) Only 2 and 3 (d) Only 1 and 3

Last Answer : (b) Only 1 and 2

Increase in values of which of the following results in an increase of the coefficient of friction in a hydrodynamic bearing? [IES 2007] 1. Viscosity of the oil. 2. Clearance between shaft and bearing. 3. Shaft speed. Select the using the code given below: (a) 1 and 2 only (b) 1 and 3 only (c) 2 and 3 only (d) 1, 2 and 3

Description : Increase in values of which of the following results in an increase of the coefficient of friction in a hydrodynamic bearing? [IES 2007] 1. Viscosity of the oil. 2. Clearance between shaft and bearing. 3. Shaft speed. Select the ... 1 and 2 only (b) 1 and 3 only (c) 2 and 3 only (d) 1, 2 and 3

Last Answer : (b) 1 and 3 only