Footstep bearing is an axial load bearing. a) True b) Thrust load c) Shear load d) None of the listed

Footstep bearing is an axial load bearing.

a) True

b) Thrust load

c) Shear load

d) None of the listed
by

1 Answer

Answer :

b) Thrust load
by

Related questions

Load acting on bearing in its plane of rotation is called as a... A. Radial load B. Axial load C. Perpendicular load D. Thrust load

Description : Load acting on bearing in its plane of rotation is called as a... A. Radial load B. Axial load C. Perpendicular load D. Thrust load

Last Answer : A. Radial load

Match List-I (Type of Anti-friction bearing) with List-II (Specific Use) and select the using the code given below the Lists: [IES-2006] List-I List -II A. Self-aligning ball bearing 1. For pure axial load B. Taper roller bearing 2. For hinged condition C. Deep groove ball bearing 3. For pure radial load D. Thrust ball bearing 4. For axial and radial load A B C D A B C D (a) 2 1 3 4 (b) 3 4 2 1 (c) 2 4 3 1 (d) 3 1 2 4

Description : Match List-I (Type of Anti-friction bearing) with List-II (Specific Use) and select the using the code given below the Lists: [IES-2006] List-I List -II A. Self-aligning ball bearing 1. For pure axial load B. Taper roller bearing 2. For ... C D (a) 2 1 3 4 (b) 3 4 2 1 (c) 2 4 3 1 (d) 3 1 2 4

Last Answer : (c) 2 4 3 1

Which of the following cannot take radial load? a) Cylindrical Roller bearing b) Taper roller bearing c) Thrust ball bearing d) None of the listed

Description : Which of the following cannot take radial load? a) Cylindrical Roller bearing b) Taper roller bearing c) Thrust ball bearing d) None of the listed

Last Answer : c) Thrust ball bearing

Which of the following cannot tolerate misalignment? (a) Angular contact bearing (b) Cylinder roller bearing (c) Thrust ball bearings (d) All of the listed

Description : Which of the following cannot tolerate misalignment? (a) Angular contact bearing (b) Cylinder roller bearing (c) Thrust ball bearings (d) All of the listed

Last Answer : (d) All of the listed

Which of the following cannot tolerate misalignment? a) Angular contact bearing b) Cylinder roller bearing c) Thrust ball bearings d) All of the listed

Description : Which of the following cannot tolerate misalignment? a) Angular contact bearing b) Cylinder roller bearing c) Thrust ball bearings d) All of the listed

Last Answer : d) All of the listed

In the expression of dynamic load capacity P=XVF(r) + YF(a), V stands for ? a) Race rotation factor b) Radial factor c) Thrust factor d) None of the listed

Description : In the expression of dynamic load capacity P=XVF(r) + YF(a), V stands for ? a) Race rotation factor b) Radial factor c) Thrust factor d) None of the listed

Last Answer : a) Race rotation factor

Which one of the following bearing is intended for a very heavy radial load? (a) Ball bearing (b) Self-aligning roller bearing (c) Roller bearing (d) Thrust bearing

Description : Which one of the following bearing is intended for a very heavy radial load? (a) Ball bearing (b) Self-aligning roller bearing (c) Roller bearing (d) Thrust bearing

Last Answer : (b) Self-aligning roller bearing

Which of the following cannot take the radial load? (a) Cylindrical Roller bearing (b) Taper roller bearing (c) Thrust ball bearing (d) Spherical roller bearing

Description : Which of the following cannot take the radial load? (a) Cylindrical Roller bearing (b) Taper roller bearing (c) Thrust ball bearing (d) Spherical roller bearing

Last Answer : (c) Thrust ball bearing

Which of the bearings given below SHOULD NOT be subjected to a thrust load? (a) Deep groove ball bearing (b) Angular contact ball bearing (c) Cylindrical (straight) roller bearing (d) Single row tapered roller bearing

Description : Which of the bearings given below SHOULD NOT be subjected to a thrust load? (a) Deep groove ball bearing (b) Angular contact ball bearing (c) Cylindrical (straight) roller bearing (d) Single row tapered roller bearing

Last Answer : (c) Cylindrical (straight) roller bearing

Match List I with List II and select the : [IES-2002] List I (Bearings) List II (Load type) A. Hydrodynamic Journal bearing 1. High radial and thrust load combined B. Rectangular Hydrostatic bearing 2. Radial load only C. Taper Roller bearing 3. Thrust load only D. Angular contact ball bearing 4. Medium to low radial and thrust combined A B C D A B C D (a) 2 3 1 4 (b) 4 1 3 2 (c) 2 1 3 4 (d) 4 3 1 2

Description : Match List I with List II and select the : [IES-2002] List I (Bearings) List II (Load type) A. Hydrodynamic Journal bearing 1. High radial and thrust load combined B. Rectangular Hydrostatic bearing 2. Radial load only C. Taper Roller ... (a) 2 3 1 4 (b) 4 1 3 2 (c) 2 1 3 4 (d) 4 3 1 2

Last Answer : (a) 2 3 1 4

A_______ bearing supports the load acting along the axis of the shaft. a) Thrust b) Radial c) Longitudinal d) Transversal

Description : A_______ bearing supports the load acting along the axis of the shaft. a) Thrust b) Radial c) Longitudinal d) Transversal

Last Answer : a) Thrust

A journal bearing is a ______ contact bearing working on the hydrodynamic lubrication and which supports load in____ direction. a) Sliding, Axial b) Rolling, Radial c) Sliding, Radial d) Rolling, Axial

Description : A journal bearing is a ______ contact bearing working on the hydrodynamic lubrication and which supports load in____ direction. a) Sliding, Axial b) Rolling, Radial c) Sliding, Radial d) Rolling, Axial

Last Answer : c) Sliding, Radial

What is the value of shear stress acting on a plane of circular bar which is subjected to axial tensile load of 100 kN? (Diamet a. 58.73 Mpa b. 40.23 Mpa c. 39.60 Mpa d. Insufficient data

Description : What is the value of shear stress acting on a plane of circular bar which is subjected to axial tensile load of 100 kN? (Diamet a. 58.73 Mpa b. 40.23 Mpa c. 39.60 Mpa d. Insufficient data

Last Answer : c. 39.60 Mpa

A bearing designed to resist axial load is known as a) Ball bearing b) bush bearing c) thrust bearing d) journal bearing

Description : A bearing designed to resist axial load is known as a) Ball bearing b) bush bearing c) thrust bearing d) journal bearing

Last Answer : c) thrust bearing

Taper rolling supports a) Axial loads b) Thrust loads c) Both axial and thrust loads d) None of the mentioned

Description : Taper rolling supports a) Axial loads b) Thrust loads c) Both axial and thrust loads d) None of the mentioned

Last Answer : c) Both axial and thrust loads

A diagram which shows the variations of the axial load for all sections of the span of a beam, is called (A) Bending moment diagram (B) Shear force diagram (C) Thrust diagram (D) Stress diagram

Description : A diagram which shows the variations of the axial load for all sections of the span of a beam, is called (A) Bending moment diagram (B) Shear force diagram (C) Thrust diagram (D) Stress diagram

Last Answer : Answer: Option C

Angular contact bearing can take thrust as well as radial loads. (a) True (b) False

Description : Angular contact bearing can take thrust as well as radial loads. (a) True (b) False

Last Answer : (a) True

Angular contact bearing can take thrust as well as radial loads. a) True b) False

Description : Angular contact bearing can take thrust as well as radial loads. a) True b) False

Last Answer : a) True

Static load is defined as the load acting on the bearing when shaft is _____ a) Stationary b) Rotating at rpm<10 c) Rotating at rpm<5 d) None of the listed

Description : Static load is defined as the load acting on the bearing when shaft is _____ a) Stationary b) Rotating at rpm

Last Answer : a) Stationary

Pitch of coil is defined as axial distance in compressed state of the coil. a) Yes b) It is measured in uncompressed state c) It is same in uncompressed or compressed state d) None of the listed

Description : Pitch of coil is defined as axial distance in compressed state of the coil. a) Yes b) It is measured in uncompressed state c) It is same in uncompressed or compressed state d) None of the listed

Last Answer : b) It is measured in uncompressed state

Woodruff key permits _____ movement b/w shaft and the hub. a) Axial b) Radial c) Eccentric d) None of the listed

Description : Woodruff key permits _____ movement b/w shaft and the hub. a) Axial b) Radial c) Eccentric d) None of the listed

Last Answer : b) Radial

Woodruff key permits _____ movement b/w shaft and the hub. a) Axial b) Radial c) Eccentric d) None of the listed

Description : Woodruff key permits _____ movement b/w shaft and the hub. a) Axial b) Radial c) Eccentric d) None of the listed

Last Answer : b) Radial

Match List -I (Bearings) with List-II (Applications) and select the using the codes given below the lists: [IAS-1998] List –I List-II A. Journal bearing 1. Electric motors B. Thrust bearing 2. Watches C. Conical pivot bearing 3. Marine engines D. Ball bearing 4. Swivelling chairs A B C D A B C D (a) 3 4 1 2 (b) 4 2 1 3 (c) 3 4 2 1 (d) 4 2 3 1

Description : Match List -I (Bearings) with List-II (Applications) and select the using the codes given below the lists: [IAS-1998] List -I List-II A. Journal bearing 1. Electric motors B. Thrust bearing 2. Watches C. Conical pivot bearing 3. Marine ... D (a) 3 4 1 2 (b) 4 2 1 3 (c) 3 4 2 1 (d) 4 2 3 1

Last Answer : (c) 3 4 2 1

The angular play bearing must be mounted without axial play. (a) Yes (b) Little tolerance is adjusted

Description : The angular play bearing must be mounted without axial play. (a) Yes (b) Little tolerance is adjusted

Last Answer : (a) Yes

Consider the following pairs of types of bearings and applications: 1. Partial Journal bearing................... Rail wagon axles 2. Full journal bearing ......................Diesel engine crank-shaft 3. Radial bearing ............................Combined radial and axial loads Which of these pairs is/are correctly matched? [IES-2000] (a) 1 alone (b) 1 and 2 (c) 2 and 3 (d) 1, 2 and 3

Description : Consider the following pairs of types of bearings and applications: 1. Partial Journal bearing................... Rail wagon axles 2. Full journal bearing ......................Diesel engine crank-shaft 3. Radial bearing ... matched? [IES-2000] (a) 1 alone (b) 1 and 2 (c) 2 and 3 (d) 1, 2 and 3

Last Answer : (b) 1 and 2

The angular play bearing must be mounted without axial play. a) Yes b) Little tolerance is adjusted c) Little tolerance is necessary d) Can’t be stated

Description : The angular play bearing must be mounted without axial play. a) Yes b) Little tolerance is adjusted c) Little tolerance is necessary d) Can’t be stated

Last Answer : a) Yes

Certain types of radial bearings can also take thrust load. a) True b) False

Description : Certain types of radial bearings can also take thrust load. a) True b) False

Last Answer : a) True

The leaves of multi-leaf springs are subjected to (A) bending stress (B) shear stress (C) axial stress (D) all of the above

Description : The leaves of multi-leaf springs are subjected to (A) bending stress (B) shear stress (C) axial stress (D) all of the above

Last Answer : (A) bending stress

When the helical compression spring is subjected to axial compressive force, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress

Description : When the helical compression spring is subjected to axial compressive force, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress

Last Answer : (D) Torsional shear stress

When the helical extension spring is subjected to axial tensile force, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress

Description : When the helical extension spring is subjected to axial tensile force, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress

Last Answer : (D) Torsional shear stress

Ellipse of stress is used to find a. Resultant stress on any plane in a bi-axial stress system b. Resultant stress on any plane in a general two dimensional system c. Maximum shear stress d. Location of planes of maximum shear stress

Description : Ellipse of stress is used to find a. Resultant stress on any plane in a bi-axial stress system b. Resultant stress on any plane in a general two dimensional system c. Maximum shear stress d. Location of planes of maximum shear stress

Last Answer : a. Resultant stress on any plane in a bi-axial stress system

An arch may be subjected to (A) Shear and axial force (B) Bending moment and shear force (C) Bending moment and axial force (D) Thrust, shear force and bending moment

Description : An arch may be subjected to  (A) Shear and axial force  (B) Bending moment and shear force  (C) Bending moment and axial force  (D) Thrust, shear force and bending moment 

Last Answer : (D) Thrust, shear force and bending moment 

An antifriction bearing consists of (a) rolling elements (b) races (c) cages (d) all of the listed

Description : An antifriction bearing consists of (a) rolling elements (b) races (c) cages (d) all of the listed

Last Answer : (d) all of the listed

The listed life of a rolling bearing, in a catalog is the, (a) minimum expected life (b) maximum expected life (c) average life (d) none of the mentioned

Description : The listed life of a rolling bearing, in a catalog is the, (a) minimum expected life (b) maximum expected life (c) average life (d) none of the mentioned

Last Answer : (a) minimum expected life

If a circular shaft is welded to the plate by means of circumferential fillet, then the shaft is subjected to torsional moment M. If throat of weld is t, then torsional shear stress is given by a) M/2πtr2 b) M/πtr2 c) M/4πtr2 d) None of the listed

Description : If a circular shaft is welded to the plate by means of circumferential fillet, then the shaft is subjected to torsional moment M. If throat of weld is t, then torsional shear stress is given by a) M/2πtr2 b) M/πtr2 c) M/4πtr2 d) None of the listed

Last Answer : a) M/2πtr2

A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and breadth of the key being 14mm and 80mm respectively. Find the shear stress induced in the key. a) 30.2N/mm2 b) 25.8N/mm2 c) 34.4N/mm2 d) None of the listed

Description : A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and breadth of the key being 14mm and 80mm respectively. Find the shear stress induced in the key. a) 30.2N/mm2 b) 25.8N/mm2 c) 34.4N/mm2 d) None of the listed

Last Answer : b) 25.8N/mm2

Maximum shear stress in transverse fillet weld of leg h and length l is a) P/hl b) 1.21P/hl c) P/1.21hl d) None of the listed

Description : Maximum shear stress in transverse fillet weld of leg h and length l is a) P/hl b) 1.21P/hl c) P/1.21hl d) None of the listed

Last Answer : b) 1.21P/hl

A force 2P is acting on the double transverse fillet weld. Leg of weld is h and length l. Determine the shear stress in a plane inclined at θ with horizontal. a) PSinθ(Sinθ+Cosθ)/hl b) P(Sinθ+Cosθ)/hl c) Pcosθ(Sinθ+Cosθ)/hl d) None of the listed

Description : A force 2P is acting on the double transverse fillet weld. Leg of weld is h and length l. Determine the shear stress in a plane inclined at θ with horizontal. a) PSinθ(Sinθ+Cosθ)/hl b) P(Sinθ+Cosθ)/hl c) Pcosθ(Sinθ+Cosθ)/hl d) None of the listed

Last Answer : a) PSinθ(Sinθ+Cosθ)/hl

Shafts are subjected to ______ forces. a) Compressive b) Tensile c) Shear d) None of the listed

Description : Shafts are subjected to ______ forces. a) Compressive b) Tensile c) Shear d) None of the listed

Last Answer : b) Tensile

Maximum shear stress in transverse fillet weld of leg h and length l is a) P/hl b) 1.21P/hl c) P/1.21hl d) None of the listed

Description : Maximum shear stress in transverse fillet weld of leg h and length l is a) P/hl b) 1.21P/hl c) P/1.21hl d) None of the listed

Last Answer : b) 1.21P/hl

A force 2P is acting on the double transverse fillet weld. Leg of weld is h and length l. Determine the shear stress in a plane inclined at θ with horizontal. a) PSinθ(Sinθ+Cosθ)/hl b) P(Sinθ+Cosθ)/hl c) Pcosθ(Sinθ+Cosθ)/hl d) None of the listed

Description : A force 2P is acting on the double transverse fillet weld. Leg of weld is h and length l. Determine the shear stress in a plane inclined at θ with horizontal. a) PSinθ(Sinθ+Cosθ)/hl b) P(Sinθ+Cosθ)/hl c) Pcosθ(Sinθ+Cosθ)/hl d) None of the listed

Last Answer : a) PSinθ(Sinθ+Cosθ)/hl

Shafts are subjected to ______ forces. a) Compressive b) Tensile c) Shear d) None of the listed

Description : Shafts are subjected to ______ forces. a) Compressive b) Tensile c) Shear d) None of the listed

Last Answer : b) Tensile

A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and breadth of the key being 14mm and 80mm respectively. Find the shear stress induced in the key. a) 30.2N/mm2 b) 25.8N/mm2 c) 34.4N/mm2 d) None of the listed

Description : A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and breadth of the key being 14mm and 80mm respectively. Find the shear stress induced in the key. a) 30.2N/mm2 b) 25.8N/mm2 c) 34.4N/mm2 d) None of the listed

Last Answer : b) 25.8N/mm2

In the expression of dynamic load capacity P=XVF r + YF a , Y stands for? (a) Race rotation factor (b) Radial load factor (c) Thrust load factor (d) Service factor

Description : In the expression of dynamic load capacity P=XVF r + YF a , Y stands for? (a) Race rotation factor (b) Radial load factor (c) Thrust load factor (d) Service factor

Last Answer : (c) Thrust load factor

In the expression of dynamic load capacity P=XVF r + YF a , X stands for? (a) Race rotation factor (b) Radial load factor (c) Thrust load factor (d) Service factor

Description : In the expression of dynamic load capacity P=XVF r + YF a , X stands for? (a) Race rotation factor (b) Radial load factor (c) Thrust load factor (d) Service factor

Last Answer : (b) Radial load factor

In the expression of dynamic load capacity P=XVF r + YF a , V stands for? (a) Race rotation factor (b) Radial load factor (c) Thrust load factor (d) Service factor

Description : In the expression of dynamic load capacity P=XVF r + YF a , V stands for? (a) Race rotation factor (b) Radial load factor (c) Thrust load factor (d) Service factor

Last Answer : (a) Race rotation factor

Which of the following bearings carry thrust load in one direction? (a) Spherical roller thrust bearings (b) Taper roller bearings (c) Spherical roller thrust bearings and taper roller bearings (d) none of the mentioned

Description : Which of the following bearings carry thrust load in one direction? (a) Spherical roller thrust bearings (b) Taper roller bearings (c) Spherical roller thrust bearings and taper roller bearings (d) none of the mentioned

Last Answer : (c) Spherical roller thrust bearings and taper roller bearings

In angular contact bearings, ____ bearings are required to take thrust load in both directions. (a) 1 (b) 2 (c) 3 (d) 4

Description : In angular contact bearings, ____ bearings are required to take thrust load in both directions. (a) 1 (b) 2 (c) 3 (d) 4

Last Answer : (b) 2

Deep groove ball bearings are used for (a) heavy thrust load only (b) the small angular displacement of shafts (c) radial load at high speed (d) combined thrust and radial loads at high speed

Description : Deep groove ball bearings are used for (a) heavy thrust load only (b) the small angular displacement of shafts (c) radial load at high speed (d) combined thrust and radial loads at high speed

Last Answer : (d) combined thrust and radial loads at high speed

In angular contact bearings, ____ bearings are required to take thrust load in both directions. a) 1 b) 4 c) 2 d) 3

Description : In angular contact bearings, ____ bearings are required to take thrust load in both directions. a) 1 b) 4 c) 2 d) 3

Last Answer : c) 2