Taper rolling supports a) Axial loads b) Thrust loads c) Both axial and thrust loads d) None of the mentioned

Taper rolling supports

a) Axial loads

b) Thrust loads

c) Both axial and thrust loads

d) None of the mentioned
by

1 Answer

Answer :

c) Both axial and thrust loads
by

Related questions

Match List-I (Type of Anti-friction bearing) with List-II (Specific Use) and select the using the code given below the Lists: [IES-2006] List-I List -II A. Self-aligning ball bearing 1. For pure axial load B. Taper roller bearing 2. For hinged condition C. Deep groove ball bearing 3. For pure radial load D. Thrust ball bearing 4. For axial and radial load A B C D A B C D (a) 2 1 3 4 (b) 3 4 2 1 (c) 2 4 3 1 (d) 3 1 2 4

Description : Match List-I (Type of Anti-friction bearing) with List-II (Specific Use) and select the using the code given below the Lists: [IES-2006] List-I List -II A. Self-aligning ball bearing 1. For pure axial load B. Taper roller bearing 2. For ... C D (a) 2 1 3 4 (b) 3 4 2 1 (c) 2 4 3 1 (d) 3 1 2 4

Last Answer : (c) 2 4 3 1

Which of the following bearings carry thrust load in one direction? (a) Spherical roller thrust bearings (b) Taper roller bearings (c) Spherical roller thrust bearings and taper roller bearings (d) none of the mentioned

Description : Which of the following bearings carry thrust load in one direction? (a) Spherical roller thrust bearings (b) Taper roller bearings (c) Spherical roller thrust bearings and taper roller bearings (d) none of the mentioned

Last Answer : (c) Spherical roller thrust bearings and taper roller bearings

A journal bearing is a ______ contact bearing working on the hydrodynamic lubrication and which supports load in____ direction. a) Sliding, Axial b) Rolling, Radial c) Sliding, Radial d) Rolling, Axial

Description : A journal bearing is a ______ contact bearing working on the hydrodynamic lubrication and which supports load in____ direction. a) Sliding, Axial b) Rolling, Radial c) Sliding, Radial d) Rolling, Axial

Last Answer : c) Sliding, Radial

The antifriction bearings (a) have low starting and low running friction at moderate speeds (b) have a high initial cost (c) can carry both radial and thrust loads (d) all the mentioned

Description : The antifriction bearings (a) have low starting and low running friction at moderate speeds (b) have a high initial cost (c) can carry both radial and thrust loads (d) all the mentioned

Last Answer : (d) all the mentioned

The tapered roller bearings can take (a) radial load only (b) axial load only (c) both radial and axial loads (d) none of the mentioned

Description : The tapered roller bearings can take (a) radial load only (b) axial load only (c) both radial and axial loads (d) none of the mentioned

Last Answer : (c) both radial and axial loads

Which of the following cannot take the radial load? (a) Cylindrical Roller bearing (b) Taper roller bearing (c) Thrust ball bearing (d) Spherical roller bearing

Description : Which of the following cannot take the radial load? (a) Cylindrical Roller bearing (b) Taper roller bearing (c) Thrust ball bearing (d) Spherical roller bearing

Last Answer : (c) Thrust ball bearing

Match List I with List II and select the : [IES-2002] List I (Bearings) List II (Load type) A. Hydrodynamic Journal bearing 1. High radial and thrust load combined B. Rectangular Hydrostatic bearing 2. Radial load only C. Taper Roller bearing 3. Thrust load only D. Angular contact ball bearing 4. Medium to low radial and thrust combined A B C D A B C D (a) 2 3 1 4 (b) 4 1 3 2 (c) 2 1 3 4 (d) 4 3 1 2

Description : Match List I with List II and select the : [IES-2002] List I (Bearings) List II (Load type) A. Hydrodynamic Journal bearing 1. High radial and thrust load combined B. Rectangular Hydrostatic bearing 2. Radial load only C. Taper Roller ... (a) 2 3 1 4 (b) 4 1 3 2 (c) 2 1 3 4 (d) 4 3 1 2

Last Answer : (a) 2 3 1 4

Which of the following cannot take radial load? a) Cylindrical Roller bearing b) Taper roller bearing c) Thrust ball bearing d) None of the listed

Description : Which of the following cannot take radial load? a) Cylindrical Roller bearing b) Taper roller bearing c) Thrust ball bearing d) None of the listed

Last Answer : c) Thrust ball bearing

Which of the following isn’t the property of a taper roller bearing? (a) High rigidity (b) Easy dismantling (c) Take low radial and heavy loads (d) It is unsuitable for high speed applications

Description : Which of the following isn’t the property of a taper roller bearing? (a) High rigidity (b) Easy dismantling (c) Take low radial and heavy loads (d) It is unsuitable for high speed applications

Last Answer : (c) Take low radial and heavy loads

Which of the following isn’t the property of taper roller? a) High rigidity b) Easy dismantling c) Take low radial and heavy loads d) All are the properties of tapper roller

Description : Which of the following isn’t the property of taper roller? a) High rigidity b) Easy dismantling c) Take low radial and heavy loads d) All are the properties of tapper roller

Last Answer : c) Take low radial and heavy loads

Tapered roller bearings can take (a) radial load only (b) axial load only (c) both radial and axial loads and the ratio of these being greater than unity (d) both radial and axial loads and the ratio of these being less than unity

Description : Tapered roller bearings can take (a) radial load only (b) axial load only (c) both radial and axial loads and the ratio of these being greater than unity (d) both radial and axial loads and the ratio of these being less than unity

Last Answer : (c) both radial and axial loads and the ratio of these being greater than unity

Load acting on bearing in its plane of rotation is called as a... A. Radial load B. Axial load C. Perpendicular load D. Thrust load

Description : Load acting on bearing in its plane of rotation is called as a... A. Radial load B. Axial load C. Perpendicular load D. Thrust load

Last Answer : A. Radial load

Footstep bearing is an axial load bearing. a) True b) Thrust load c) Shear load d) None of the listed

Description : Footstep bearing is an axial load bearing. a) True b) Thrust load c) Shear load d) None of the listed

Last Answer : b) Thrust load

A_______ bearing supports the load acting along the axis of the shaft. a) Thrust b) Radial c) Longitudinal d) Transversal

Description : A_______ bearing supports the load acting along the axis of the shaft. a) Thrust b) Radial c) Longitudinal d) Transversal

Last Answer : a) Thrust

Angular contact bearing can take thrust as well as radial loads. (a) True (b) False

Description : Angular contact bearing can take thrust as well as radial loads. (a) True (b) False

Last Answer : (a) True

Deep groove ball bearings are used for (a) heavy thrust load only (b) the small angular displacement of shafts (c) radial load at high speed (d) combined thrust and radial loads at high speed

Description : Deep groove ball bearings are used for (a) heavy thrust load only (b) the small angular displacement of shafts (c) radial load at high speed (d) combined thrust and radial loads at high speed

Last Answer : (d) combined thrust and radial loads at high speed

Angular contact bearing can take thrust as well as radial loads. a) True b) False

Description : Angular contact bearing can take thrust as well as radial loads. a) True b) False

Last Answer : a) True

Consider the following pairs of types of bearings and applications: 1. Partial Journal bearing................... Rail wagon axles 2. Full journal bearing ......................Diesel engine crank-shaft 3. Radial bearing ............................Combined radial and axial loads Which of these pairs is/are correctly matched? [IES-2000] (a) 1 alone (b) 1 and 2 (c) 2 and 3 (d) 1, 2 and 3

Description : Consider the following pairs of types of bearings and applications: 1. Partial Journal bearing................... Rail wagon axles 2. Full journal bearing ......................Diesel engine crank-shaft 3. Radial bearing ... matched? [IES-2000] (a) 1 alone (b) 1 and 2 (c) 2 and 3 (d) 1, 2 and 3

Last Answer : (b) 1 and 2

________is suitable as a lubricant for low and moderate loads applications of rolling contact bearing. (a) Grease (b) Lubricating oil (c) Graphite (d) Air

Description : ________is suitable as a lubricant for low and moderate loads applications of rolling contact bearing. (a) Grease (b) Lubricating oil (c) Graphite (d) Air

Last Answer : (a) Grease

Which of the following elements is not used as a roller in roller bearings? (a) Cylindrical (b) Taper (c) Spherical (d) None of the mentioned

Description : Which of the following elements is not used as a roller in roller bearings? (a) Cylindrical (b) Taper (c) Spherical (d) None of the mentioned

Last Answer : (d) None of the mentioned

The taper on cotter and slot is fomed on both the location is agreed or not.. a) agree b) disagree

Description : The taper on cotter and slot is fomed on both the location is agreed or not.. a) agree b) disagree

Last Answer : b) disagree

Taper is made cotter and slot on both the side. A. Yes B. No

Description : Taper is made cotter and slot on both the side. A. Yes B. No

Last Answer : B. No

Taper is given on key is generally.......... A. Top side only B. Bottom side only C. On both side D. Any side

Description : Taper is given on key is generally.......... A. Top side only B. Bottom side only C. On both side D. Any side

Last Answer : A. Top side only

Cotter joint is used when the members are subjected to which type of stresses? a) Axial tensile b) Axial compressive c) Axial tensile or compressive d) None of the mentioned

Description : Cotter joint is used when the members are subjected to which type of stresses? a) Axial tensile b) Axial compressive c) Axial tensile or compressive d) None of the mentioned

Last Answer : c) Axial tensile or compressive

The listed life of a rolling bearing, in a catalog is the, (a) minimum expected life (b) maximum expected life (c) average life (d) none of the mentioned

Description : The listed life of a rolling bearing, in a catalog is the, (a) minimum expected life (b) maximum expected life (c) average life (d) none of the mentioned

Last Answer : (a) minimum expected life

The rolling contact bearings as compared to sliding contact bearings have (a) small overall dimensions (b) accuracy of shaft alignment (c) low starting and low running friction except at very high speeds (d) all the mentioned

Description : The rolling contact bearings as compared to sliding contact bearings have (a) small overall dimensions (b) accuracy of shaft alignment (c) low starting and low running friction except at very high speeds (d) all the mentioned

Last Answer : (d) all the mentioned

In standard taper roller bearings, the angle of taper of the outer raceway is (a) 5° (b) 8° (c) 15° (d) 25°

Description : In standard taper roller bearings, the angle of taper of the outer raceway is (a) 5° (b) 8° (c) 15° (d) 25°

Last Answer : (d) 25°

Which of the following bearing is preferred for oscillating conditions? (a) Double row roller bearing (b) Taper roller bearing (c) Needle roller bearing (d) Angular contact single row ball bearing

Description : Which of the following bearing is preferred for oscillating conditions? (a) Double row roller bearing (b) Taper roller bearing (c) Needle roller bearing (d) Angular contact single row ball bearing

Last Answer : (c) Needle roller bearing

Taper on Cotter is varies from A. 1 in 15 to 1 in 12 B. 1 in 20 to 1 in 15 C. 1 in 25 to 1 in 20 D. 1 in 48 to 1 in 24

Description : Taper on Cotter is varies from A. 1 in 15 to 1 in 12 B. 1 in 20 to 1 in 15 C. 1 in 25 to 1 in 20 D. 1 in 48 to 1 in 24

Last Answer : D. 1 in 48 to 1 in 24

Taper on rectangular sink key is ....... A. 1 in 16 B. 1 in 48 C. 1 in 100 D. 1 in 120

Description : Taper on rectangular sink key is ....... A. 1 in 16 B. 1 in 48 C. 1 in 100 D. 1 in 120

Last Answer : C. 1 in 100

In angular contact bearings, ____ bearings are required to take thrust load in both directions. (a) 1 (b) 2 (c) 3 (d) 4

Description : In angular contact bearings, ____ bearings are required to take thrust load in both directions. (a) 1 (b) 2 (c) 3 (d) 4

Last Answer : (b) 2

In angular contact bearings, ____ bearings are required to take thrust load in both directions. a) 1 b) 4 c) 2 d) 3

Description : In angular contact bearings, ____ bearings are required to take thrust load in both directions. a) 1 b) 4 c) 2 d) 3

Last Answer : c) 2

In the expression of dynamic load capacity P=XVF r + YF a , Y stands for? (a) Race rotation factor (b) Radial load factor (c) Thrust load factor (d) Service factor

Description : In the expression of dynamic load capacity P=XVF r + YF a , Y stands for? (a) Race rotation factor (b) Radial load factor (c) Thrust load factor (d) Service factor

Last Answer : (c) Thrust load factor

In the expression of dynamic load capacity P=XVF r + YF a , X stands for? (a) Race rotation factor (b) Radial load factor (c) Thrust load factor (d) Service factor

Description : In the expression of dynamic load capacity P=XVF r + YF a , X stands for? (a) Race rotation factor (b) Radial load factor (c) Thrust load factor (d) Service factor

Last Answer : (b) Radial load factor

In the expression of dynamic load capacity P=XVF r + YF a , V stands for? (a) Race rotation factor (b) Radial load factor (c) Thrust load factor (d) Service factor

Description : In the expression of dynamic load capacity P=XVF r + YF a , V stands for? (a) Race rotation factor (b) Radial load factor (c) Thrust load factor (d) Service factor

Last Answer : (a) Race rotation factor

Which of the following cannot tolerate misalignment? (a) Angular contact bearing (b) Cylinder roller bearing (c) Thrust ball bearings (d) All of the listed

Description : Which of the following cannot tolerate misalignment? (a) Angular contact bearing (b) Cylinder roller bearing (c) Thrust ball bearings (d) All of the listed

Last Answer : (d) All of the listed

Which one of the following bearing is intended for a very heavy radial load? (a) Ball bearing (b) Self-aligning roller bearing (c) Roller bearing (d) Thrust bearing

Description : Which one of the following bearing is intended for a very heavy radial load? (a) Ball bearing (b) Self-aligning roller bearing (c) Roller bearing (d) Thrust bearing

Last Answer : (b) Self-aligning roller bearing

Which of the bearings given below SHOULD NOT be subjected to a thrust load? (a) Deep groove ball bearing (b) Angular contact ball bearing (c) Cylindrical (straight) roller bearing (d) Single row tapered roller bearing

Description : Which of the bearings given below SHOULD NOT be subjected to a thrust load? (a) Deep groove ball bearing (b) Angular contact ball bearing (c) Cylindrical (straight) roller bearing (d) Single row tapered roller bearing

Last Answer : (c) Cylindrical (straight) roller bearing

Match List -I (Bearings) with List-II (Applications) and select the using the codes given below the lists: [IAS-1998] List –I List-II A. Journal bearing 1. Electric motors B. Thrust bearing 2. Watches C. Conical pivot bearing 3. Marine engines D. Ball bearing 4. Swivelling chairs A B C D A B C D (a) 3 4 1 2 (b) 4 2 1 3 (c) 3 4 2 1 (d) 4 2 3 1

Description : Match List -I (Bearings) with List-II (Applications) and select the using the codes given below the lists: [IAS-1998] List -I List-II A. Journal bearing 1. Electric motors B. Thrust bearing 2. Watches C. Conical pivot bearing 3. Marine ... D (a) 3 4 1 2 (b) 4 2 1 3 (c) 3 4 2 1 (d) 4 2 3 1

Last Answer : (c) 3 4 2 1

In the expression of dynamic load capacity P=XVF(r) + YF(a), V stands for ? a) Race rotation factor b) Radial factor c) Thrust factor d) None of the listed

Description : In the expression of dynamic load capacity P=XVF(r) + YF(a), V stands for ? a) Race rotation factor b) Radial factor c) Thrust factor d) None of the listed

Last Answer : a) Race rotation factor

Which of the following cannot tolerate misalignment? a) Angular contact bearing b) Cylinder roller bearing c) Thrust ball bearings d) All of the listed

Description : Which of the following cannot tolerate misalignment? a) Angular contact bearing b) Cylinder roller bearing c) Thrust ball bearings d) All of the listed

Last Answer : d) All of the listed

Certain types of radial bearings can also take thrust load. a) True b) False

Description : Certain types of radial bearings can also take thrust load. a) True b) False

Last Answer : a) True

In axial thrust diagram, at which point bending moment is zero? (a) Point of contra-flexure (b) Point of inflection (c) Both a. and b. (d) None of the above

Description : In axial thrust diagram, at which point bending moment is zero? (a) Point of contra-flexure (b) Point of inflection (c) Both a. and b. (d) None of the above

Last Answer : (c) Both a. and b.

Tapper roller bearing are used in disc harrow because a) It can take heavy radial loads b) It can take both radial as well as end thrust c) It can operate effectively at low speed and in contact with dirt d) Both (b) and (c) are true

Description : Tapper roller bearing are used in disc harrow because a) It can take heavy radial loads b) It can take both radial as well as end thrust c) It can operate effectively at low speed and in contact with dirt d) Both (b) and (c) are true

Last Answer : d) Both (b) and (c) are true

Feather key can be used to prevent axial motion between two elements. a) True b) False

Description : Feather key can be used to prevent axial motion between two elements. a) True b) False

Last Answer : b) False

The angular play bearing must be mounted without axial play. (a) Yes (b) Little tolerance is adjusted

Description : The angular play bearing must be mounted without axial play. (a) Yes (b) Little tolerance is adjusted

Last Answer : (a) Yes

A cotter joint is used to connect two __________ rods. A. Co-axial B. Perpendicular C. Parallel D. None of these

Description : A cotter joint is used to connect two __________ rods. A. Co-axial B. Perpendicular C. Parallel D. None of these

Last Answer : A. Co-axial

The angular play bearing must be mounted without axial play. a) Yes b) Little tolerance is adjusted c) Little tolerance is necessary d) Can’t be stated

Description : The angular play bearing must be mounted without axial play. a) Yes b) Little tolerance is adjusted c) Little tolerance is necessary d) Can’t be stated

Last Answer : a) Yes

Axial length of an unloaded helical compression spring is called (A) compressed length (B) solid length (C) free length (D) none of the above

Description : Axial length of an unloaded helical compression spring is called (A) compressed length (B) solid length (C) free length (D) none of the above

Last Answer : (C) free length

Axial length of the spring which is so compressed that the adjacent coils touch each other. (A) compressed length (B) solid length (C) free length (D) none of the above

Description : Axial length of the spring which is so compressed that the adjacent coils touch each other. (A) compressed length (B) solid length (C) free length (D) none of the above

Last Answer : (B) solid length