Description : Which of the following is expression for stribeck equation?(Number of balls=z)? a) C=kd2z/5 b) C=kd2z/15 c) C=kd2z/10 d) None of the listed
Last Answer : a) C=kd2z/5
Description : Stribeck equation gives the dynamic load capacity of the bearing. (a) True (b) False
Last Answer : (b) False
Description : Stribeck equation gives dynamic load capacity of the bearing. a) True b) False
Last Answer : b) False
Description : The purpose of lubrication in an antifriction bearing is (a) to reduce the friction between balls and races (b) dissipation of frictional heat prevention of corrosion (c) protection of the bearing from dirt and other foreign particles (d) all of the mentioned
Last Answer : (d) all of the mentioned
Description : Which one of the following parts of a ball bearing acts as a barrier between the balls preventing them from bumping into each other? (a) Inner race (b) Outer race (c) Rolling element (d) Cage
Last Answer : (d) Cage
Description : The ball bearings are provided with a cage (a) to reduce friction (b) to facilitate slipping of balls (c) to prevent the lubricant from flowing out (d) to maintain the balls at a fixed distance apart
Last Answer : (d) to maintain the balls at a fixed distance apart
Description : Balls and the races of the deep groove ball may roll freely without any sliding. a) True b) False
Last Answer : a) True
Description : Taper on Cotter is varies from A. 1 in 15 to 1 in 12 B. 1 in 20 to 1 in 15 C. 1 in 25 to 1 in 20 D. 1 in 48 to 1 in 24
Last Answer : D. 1 in 48 to 1 in 24
Description : In the expression of dynamic load capacity P=XVF r + YF a , Y stands for? (a) Race rotation factor (b) Radial load factor (c) Thrust load factor (d) Service factor
Last Answer : (c) Thrust load factor
Description : In the expression of dynamic load capacity P=XVF r + YF a , X stands for? (a) Race rotation factor (b) Radial load factor (c) Thrust load factor (d) Service factor
Last Answer : (b) Radial load factor
Description : In the expression of dynamic load capacity P=XVF r + YF a , V stands for? (a) Race rotation factor (b) Radial load factor (c) Thrust load factor (d) Service factor
Last Answer : (a) Race rotation factor
Description : In the expression of dynamic load capacity P=XVF(r) + YF(a), V stands for ? a) Race rotation factor b) Radial factor c) Thrust factor d) None of the listed
Last Answer : a) Race rotation factor
Description : The static load is defined as the load acting on the bearing when the shaft is _____. (a) stationary (b) rotating at rpm
Last Answer : (a) stationary
Description : The relationship between the alternating stress and mean stress is given by the following equation: σ a =σ e [1-(σ m /σ u )x], where σ e is the fatigue limit for completely reversed loading. The value of x for Gerber line is equal to _________ a) 1 b) 2 c) 0.5 d) -1
Last Answer : b) 2
Description : The relationship between the alternating stress and mean stress is given by the following equation: σ a = σ e [1-(σ m /σ u ) x ]. The value of x for Goodman line is equal to _________ a) 1 b) 2 c) 0.5 d) -1
Last Answer : a) 1
Description : Petroff’s equation is used to find out (A) Load carrying capacity of the bearing (B) Frictional losses in the bearing (C) Unit bearing pressure on the bearing (D) Pressure distribution around the periphery of the journal
Last Answer : (B) Frictional losses in the bearing
Description : Which of the following are not true for petroff’s equation? a) Shaft is considered concentric with the bearing b) Bearing is subjected to light load c) Is used to find coefficient of friction d) Frictional torque is given by fpr2l
Last Answer : d) Frictional torque is given by fpr2l
Description : Notch sensitivity (q) is given by the equation _______ where K f = fatigue stress concentration factor and K t = theoretical stress concentration factor a. ( K f + 1 ) / ( K t – 1 ) b. ( K f – 1 ) / ( K t – 1 ) c. ( K f + 1 ) / ( K t + 1 ) d. ( K f - 1 ) / ( K t + 1 )
Last Answer : b. ( K f – 1 ) / ( K t – 1 )
Description : Mohr’s stress circle is named so because it has equation of the form a. x^2 + y^2 = r^2 b. (x-a)^2 + y^2 = r^2 c. (x-a)^2 + (y-b)^2 = r^2 d. It was desired by German Engineer Otto Mohr
Last Answer : b. (x-a)^2 + y^2 = r^2
Description : The bearings of medium series have capacity __________ over the light series. (a) 10 to 20% (b) 20 to 30% (c) 30 to 40% (d) 40 to 50%
Last Answer : (c) 30 to 40%
Description : The bearings of heavy series have capacity __________ over the medium series. (a) 10 to 20% (b) 20 to 30% (c) 30 to 40% (d) 40 to 50%
Last Answer : (b) 20 to 30%
Description : The equation, X = A cos(wt + f) (read: X equals A times the cosine of omega t + phi (fee)), can represent an expression for: w) accelerating due to gravity x) uniform straight line motion y) dc current z) a simple harmonic oscillator
Last Answer : ANSWER: Z -- A SIMPLE HARMONIC OSCILLATOR
Description : The graphical method of Mohr's circle represents shear stress (τ) on ______ a. X-axis b. Y-axis c. Z-axis d. None of the above
Last Answer : b. Y-axis
Description : A spring with index=15 is prone to buckling. a) True b) False
Description : If core diameter of bolt is 13.8cm the it’s nominal diameter is given by? a) 17.27mm b) 15.34mm c) 14.67mm d) 16.34mm
Last Answer : a) 17.27mm
Description : The angle between a principal plane and a plane of maximum shear is a. 15 0 b. 45 0 c. 75 0 d. None
Last Answer : b. 45 0
Description : A circular solid of uniform thickness 20 mm, radius 200 mm and mass 20 kg, is used as a flywheel. If it rotates at 600 rpm, the kinetic energy of the flywheel, in joules is 1. 395 2. 790 3. 1580 4. 3160
Last Answer : 2. 790
Description : A flywheel connected to a punching machine has to supply energy of 400 Nm while running at a mean angular speed of 20 rad/s. If the total fluctuation of speed is not exceed to in kgm 2 is 1. 25 2. 50 3. 100 4. 125
Last Answer : 1. 25
Description : A spring index from ___ is considered as best for manufacturing considerations. (A) 4 to 12 (B) 12 to 20 (C) 20 to 28 (D) 28 to 36
Last Answer : (A) 4 to 12
Description : The helix angle is very small about 20. The spring is open coiled spring. a) Yes b) It is closed coiled spring c) That small angle isn’t possible d) None of the listed
Last Answer : b) It is closed coiled spring
Description : The angle of a fillet weld is a. 20 0 b. 40 0 c. 45 0 d. None
Last Answer : c. 45 0
Description : When a material is subjected to fatigue loading, the ratio of the endurance limit to the ultimate tensile strength is (a) 0.20 (b) 0.35 (c) 0.50 (d) 0.65
Last Answer : (c) 0.50
Description : A full journal bearing having clearance to radius ratio of 1/100, using a lubricant with μ=28×10-3 Pa s supports the shaft journal running at N = 2400 rpm If bearing pressure is 1.4 MPa, the Somerfield number is [IES-2001] (a) 8×10-3 (b) 8×10-5 (c) 0.48 (d) 0.48×10
Last Answer : (a) S = (μN s /p) (r/c) 2
Description : The cost of a toy horse is same as that of cost of 3 balls. Express this statement as a linear equation in two variables. Also draw its graph. -Maths 9th
Last Answer : Solution :-
Description : Static load is defined as the load acting on the bearing when shaft is _____ a) Stationary b) Rotating at rpm
Last Answer : a) Stationary
Description : Strength of a welded joint increases by radio graphing by i. 10 % ii. 12% iii. 15% iv. None
Last Answer : ii. 12%
Description : Find the shear stress in a flange at the junction of hub in rigid flanged coupling if torsional moment is 2980N-m and diameter of hub being 125mm. Also the thickness of flange is 25mm. a) 6.77N/mm2 b) 10.24N/mm2 c) 4.84N/mm2 d) 4.22N/mm2
Last Answer : c) 4.84N/mm2
Description : A bag contains x white, y red and z blue balls. -Maths 9th
Last Answer : Number of blue balls = z Total balls = x + y + z therefore P(blue ball)= z /(x+y+z )
Description : A firecracker is placed in the middle of a cluster of stationary billiard balls. The firecracker-billiard ball system sits on a frictionless surface. As the firecracker explodes, the balls scatter. What is the momentum ... to the combined speed of the balls y) equal to the mass of the balls z) zero
Last Answer : ANSWER: Z -- ZERO
Description : Two steel balls are at a distance S from one another. As the mass of ONE of the balls is doubled, the gravitational force of attraction between them is: w) quartered x) halved y) doubled z) quadrupled
Last Answer : ANSWER: Y -- DOUBLED
Description : Moth balls contain: w) formalin x) chitin (pron: kite-en) y) formaldehyde z) naphthalene
Last Answer : ANSWER: Z -- NAPHTHALENE
Description : If a bearing is designated by the number 305, it means that the bearing is of (a) light series whose bore is 5 mm (b) light series whose bore is 25 mm (c) medium series whose bore is 5 mm (d) medium series whose bore is 25 mm
Last Answer : (d) medium series whose bore is 25 mm
Description : If shaft diameter is 30mm and number of pins emplaced are 6, then the diameter of the pin will be? a) 6.4mm b) 5.6mm c) 6.1mm d) 5.9mm
Last Answer : c) 6.1mm
Description : The maximum number of principal stresses is a. 1 b. 3 c. 5 d. None
Last Answer : b. 3
Description : What is considered to be the approximate difference in average temperature between the "little ice age" and today? w) 1 to 3 degrees centigrade x) 5 to 8 degrees centigrade y) 10 to 12 degrees centigrade z) 15 to 20 degrees centigrade
Last Answer : ANSWER: W -- 1 TO 3 DEGREES CENTIGRADE
Description : Which one of the following pair is correctly matched? [IES-2000] (a) Beauchamp tower ........................First experiments on journal bearings (b) Osborne Reynolds ........................ ... .Pivot and Collar bearings (d) Ball bearings...............................Hydrodynamic lubrication
Last Answer : (a) Beauchamp tower ........................First experiments on journal bearings
Description : The bearing characteristic number in a hydrodynamic bearing depends on- (a) Length, width and load (b) length, width and speed. [IES-1996] (c) Viscosity, speed and load (d) viscosity, speed and bearing pressure.
Last Answer : (d) viscosity, speed and bearing pressure.
Description : If μ = absolute viscosity, N= speed of the journal and p = unit bearing pressure, then the bearing characteristic number is given by (A) μN/p (B) μp/N (C) pN/μ (D) μ/pN
Last Answer : (A) μN/p