A spring index from ___ is considered as best for manufacturing considerations. (A) 4 to 12 (B) 12 to 20 (C) 20 to 28 (D) 28 to 36

A spring index from ___ is considered as best for manufacturing considerations.

(A) 4 to 12

(B) 12 to 20

(C) 20 to 28

(D) 28 to 36
by

1 Answer

Answer :

(A) 4 to 12
by

Related questions

The spring index indicates the relative sharpness of the ___ of the coil. (A) length (B) curvature (C) thickness (D) none of the above

Description : The spring index indicates the relative sharpness of the ___ of the coil. (A) length (B) curvature (C) thickness (D) none of the above

Last Answer : (B) curvature

A spring is defined as a(an) ___ machine element. (A) plastic (B) elastic (C) special purpose (D) none of the above

Description : A spring is defined as a(an) ___ machine element. (A) plastic (B) elastic (C) special purpose (D) none of the above

Last Answer : (B) elastic

The spring index (C) is (A) mean coil diameter / wire diameter (B) wire diameter / mean coil diameter (C) wire diameter x mean coil diameter (D) none of the above

Description : The spring index (C) is (A) mean coil diameter / wire diameter (B) wire diameter / mean coil diameter (C) wire diameter x mean coil diameter (D) none of the above

Last Answer : (A) mean coil diameter / wire diameter

The spring index is, (A) Ratio of wire diameter to mean coil diameter (B) Force per unit cross-sectional area of spring (C) Ratio of mean coil diameter to wire diameter (D) Force required to produce unit deflection

Description : The spring index is, (A) Ratio of wire diameter to mean coil diameter (B) Force per unit cross-sectional area of spring (C) Ratio of mean coil diameter to wire diameter (D) Force required to produce unit deflection

Last Answer : (C) Ratio of mean coil diameter to wire diameter

When two concentric springs are made of same material, having same free length and compressed equally by axial load, then the load shared by each spring is proportional to (A) Spring index of each spring (B) Wire diameter of each spring (C) Mean coil diameter of each spring (D) Square of wire diameter of each spring

Description : When two concentric springs are made of same material, having same free length and compressed equally by axial load, then the load shared by each spring is proportional to (A) Spring index of each spring ... spring (C) Mean coil diameter of each spring (D) Square of wire diameter of each spring

Last Answer : (D) Square of wire diameter of each spring

For a helical torsion sprig, the stress concentration factor at outer fibre is? Give spring index=5. a) 0.78 b) 0.87 c) 1.87 d) 0.69

Description : For a helical torsion sprig, the stress concentration factor at outer fibre is? Give spring index=5. a) 0.78 b) 0.87 c) 1.87 d) 0.69

Last Answer : b) 0.87

For a helical torsion sprig, the stress concentration factor at inner fibre is? Give spring index=5. a) 1.005 b) 1.175 c) 1.223 d) 1.545

Description : For a helical torsion sprig, the stress concentration factor at inner fibre is? Give spring index=5. a) 1.005 b) 1.175 c) 1.223 d) 1.545

Last Answer : b) 1.175

Find the Wahl’s factor if spring index is 6. a) 1.2020 b) 1.2424 c) 1.2525 d) 1.5252

Description : Find the Wahl’s factor if spring index is 6. a) 1.2020 b) 1.2424 c) 1.2525 d) 1.5252

Last Answer : c) 1.2525

A spring with index=15 is prone to buckling. a) True b) False

Description : A spring with index=15 is prone to buckling. a) True b) False

Last Answer : a) True

If spring index=2.5, what can be concluded about stresses in the wire? a) They are high b) They are negligible c) They are moderate d) Cannot be determined

Description : If spring index=2.5, what can be concluded about stresses in the wire? a) They are high b) They are negligible c) They are moderate d) Cannot be determined

Last Answer : a) They are high

The spring index is the ratio of wire diameter to mean coil diameter. a) True b) False

Description : The spring index is the ratio of wire diameter to mean coil diameter. a) True b) False

Last Answer : a) True

The normal stress is perpendicular to the area under considerations, while the shear stress acts over the area. a) True b) False

Description : The normal stress is perpendicular to the area under considerations, while the shear stress acts over the area. a) True b) False

Last Answer : a) True

The helix angle is very small about 20. The spring is open coiled spring. a) Yes b) It is closed coiled spring c) That small angle isn’t possible d) None of the listed

Description : The helix angle is very small about 20. The spring is open coiled spring. a) Yes b) It is closed coiled spring c) That small angle isn’t possible d) None of the listed

Last Answer : b) It is closed coiled spring

If load on the engine is constant, the mean speed will be constant and ___ will not operate. a) Flywheel b) Governor c) Both flywheel and governor d) None of the mentioned

Description : If load on the engine is constant, the mean speed will be constant and ___ will not operate. a) Flywheel b) Governor c) Both flywheel and governor d) None of the mentioned

Last Answer : b) Governor

Involute splines have stub teeth with a pressure angle of ___ a) 30 b) 45 c) 60 d) Can’t be determined

Description : Involute splines have stub teeth with a pressure angle of ___ a) 30 b) 45 c) 60 d) Can’t be determined

Last Answer : b) 45

Involute splines have stub teeth with a pressure angle of ___ a) 30 b) 45 c) 60 d) Can’t be determined

Description : Involute splines have stub teeth with a pressure angle of ___ a) 30 b) 45 c) 60 d) Can’t be determined

Last Answer : b) 45

In a general two dimensional stress system, planes of maximum shear stress are inclined at ___ with principal planes. a. 90 degree b. 180 degree c. 45 degree d. 60 degree

Description : In a general two dimensional stress system, planes of maximum shear stress are inclined at ___ with principal planes. a. 90 degree b. 180 degree c. 45 degree d. 60 degree

Last Answer : c. 45 degree

1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 23, 24, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34, 35, 36, 37, 38, 39, 40, 41, 42, 43, 44, 45, 46, 47, 48, 49, 50'. What number is missing? -Riddles

Description : 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 23, 24, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34, 35, 36, 37, 38, 39, 40, 41, 42, 43, 44, 45, 46, 47, 48, 49, 50'. What number is missing? -Riddles

Last Answer : 22

Ratio of ages of three girls are 5:8:10, six years ago, the sum of their ages was 28. Find their present ages. a) 16,10,20 b) 12,28,36 c) 10,16,20 d) 16,28,36

Description : Ratio of ages of three girls are 5:8:10, six years ago, the sum of their ages was 28. Find their present ages. a) 16,10,20 b) 12,28,36 c) 10,16,20 d) 16,28,36

Last Answer : C Let the present ages are 5x, 8x, 10x. => (5x-6) + (8x-6) + (10x-6) = 28 => 23x = 46 => x = 2 So their present ages are: 10,16,20

Two pipe P & Q fill a tab in 5 hrs and 20 hrs respectively. If both the pipes are open then due to the leakage, it took 30mins more to fill the tab. If the tab is full, how long will it take for the leakage alone to empty the tank? A) 28 B) 24 C) 36 D) 12

Description : Two pipe P & Q fill a tab in 5 hrs and 20 hrs respectively. If both the pipes are open then due to the leakage, it took 30mins more to fill the tab. If the tab is full, how long will it take for the leakage alone to empty the tank? A) 28 B) 24 C) 36 D) 12

Last Answer : C Part filled by(P+Q) in 1 hr = 1/5 + 1/20 = ¼ So P & Q together can fill the tank in 4 hrs. Work done by the leak in 1 hr = 1 / 4 - 2/9 Leak will empty the tank in 36 hrs.

Which of the following is usually not one of the top considerations in choosing a manufacturing location? a. availability availability of labor and labor productivity b. productivity b. exchange rates exchange rates c. attitude attitude of governmental governmental units d. zoning regulations e. entertainment entertainment opportunities

Description : Which of the following is usually not one of the top considerations in choosing a manufacturing location? a. availability availability of labor and labor productivity b. ... attitude attitude of governmental governmental units d. zoning regulations e. entertainment entertainment opportunities

Last Answer : d. zoning regulations

Teflon can be used for manufacturing of knuckle joints. A. True B. False

Description : Teflon can be used for manufacturing of knuckle joints. A. True B. False

Last Answer : A. True

A weld symbol is necessary because of (i) Aesthetic sense (ii) Finishing (iii) Manufacturing (iv) None

Description : A weld symbol is necessary because of (i) Aesthetic sense (ii) Finishing (iii) Manufacturing (iv) None

Last Answer : (iii) Manufacturing

A rolling contact bearing is specified as X307. Calculate the bearing diameter. (a) 35 mm (b) 28 mm (c) 21 mm (d) 7 mm

Description : A rolling contact bearing is specified as X307. Calculate the bearing diameter. (a) 35 mm (b) 28 mm (c) 21 mm (d) 7 mm

Last Answer : (a) 35 mm

A full journal bearing having clearance to radius ratio of 1/100, using a lubricant with μ=28×10-3 Pa s supports the shaft journal running at N = 2400 rpm If bearing pressure is 1.4 MPa, the Somerfield number is [IES-2001] (a) 8×10-3 (b) 8×10-5 (c) 0.48 (d) 0.48×10

Description : A full journal bearing having clearance to radius ratio of 1/100, using a lubricant with μ=28×10-3 Pa s supports the shaft journal running at N = 2400 rpm If bearing pressure is 1.4 MPa, the Somerfield number is [IES-2001] (a) 8×10-3 (b) 8×10-5 (c) 0.48 (d) 0.48×10

Last Answer : (a) S = (μN s /p) (r/c) 2

The designation M 36 × 2 means (A) Metric fine threads of 36 mm outside diameter and 2 mm pitch (B) Metric coarse threads of 36 mm outside diameter and 2 mm pitch (C) Metric threads of 36 mm pitch diameter and 2 mm pitch (D) Metric threads of 36 mm core diameter and 2 mm pitch

Description : The designation M 36 × 2 means (A) Metric fine threads of 36 mm outside diameter and 2 mm pitch (B) Metric coarse threads of 36 mm outside diameter and 2 mm pitch (C) Metric threads of 36 mm pitch diameter and 2 mm pitch (D) Metric threads of 36 mm core diameter and 2 mm pitch

Last Answer : (A) Metric fine threads of 36 mm outside diameter and 2 mm pitch

Taper on Cotter is varies from A. 1 in 15 to 1 in 12 B. 1 in 20 to 1 in 15 C. 1 in 25 to 1 in 20 D. 1 in 48 to 1 in 24

Description : Taper on Cotter is varies from A. 1 in 15 to 1 in 12 B. 1 in 20 to 1 in 15 C. 1 in 25 to 1 in 20 D. 1 in 48 to 1 in 24

Last Answer : D. 1 in 48 to 1 in 24

-The method used to induce a layer of residual compressive stress on the surface of the spring wire, is (A) shot peening (B) burnishing (C) lapping (D) none of the above

Description : -The method used to induce a layer of residual compressive stress on the surface of the spring wire, is (A) shot peening (B) burnishing (C) lapping (D) none of the above

Last Answer : (A) shot peening

A concentric spring consist of two helical compression springs (A) both springs always have right hand helix (B) both springs always have left hand helix (C) both springs always have opposite hand of helices (D) any of the above

Description : A concentric spring consist of two helical compression springs (A) both springs always have right hand helix (B) both springs always have left hand helix (C) both springs always have opposite hand of helices (D) any of the above

Last Answer : (C) both springs always have opposite hand of helices

The strain energy (E) stored in the spring is given by Where P=Load and δ = deflection of spring (A) Pδ/2 (B) 2Pδ (C) Pδ/3 (D) Pδ/4

Description : The strain energy (E) stored in the spring is given by Where P=Load and δ = deflection of spring (A) Pδ/2 (B) 2Pδ (C) Pδ/3 (D) Pδ/4

Last Answer : (A) Pδ/2

The length of one coil in the spring is (A) πD (B) 2πD (C) πD/2 (D) πD/4

Description : The length of one coil in the spring is (A) πD (B) 2πD (C) πD/2 (D) πD/4

Last Answer : (A) πD

The coils of spring which are in contact with the seat and do not contribute to spring action are called (A) resting coils (B) static coils (C) inactive coils (D) ideal coils

Description : The coils of spring which are in contact with the seat and do not contribute to spring action are called (A) resting coils (B) static coils (C) inactive coils (D) ideal coils

Last Answer : (C) inactive coils

The force required to produce unit deflection is known as (A) gradient of spring (B) stiffness of the spring (C) spring constant (D) all of the above

Description : The force required to produce unit deflection is known as (A) gradient of spring (B) stiffness of the spring (C) spring constant (D) all of the above

Last Answer : (D) all of the above

Axial length of an unloaded helical compression spring is called (A) compressed length (B) solid length (C) free length (D) none of the above

Description : Axial length of an unloaded helical compression spring is called (A) compressed length (B) solid length (C) free length (D) none of the above

Last Answer : (C) free length

Axial length of the spring which is so compressed that the adjacent coils touch each other. (A) compressed length (B) solid length (C) free length (D) none of the above

Description : Axial length of the spring which is so compressed that the adjacent coils touch each other. (A) compressed length (B) solid length (C) free length (D) none of the above

Last Answer : (B) solid length

The longest leaf in Semi-elliptic leaf spring is known as (A) chief leaf (B) master leaf (C) major leaf (D) higher leaf

Description : The longest leaf in Semi-elliptic leaf spring is known as (A) chief leaf (B) master leaf (C) major leaf (D) higher leaf

Last Answer : (B) master leaf

Helical torsion spring is used in (A) door hinges (B) door closers (C) automobile starters (D) all of the above

Description : Helical torsion spring is used in (A) door hinges (B) door closers (C) automobile starters (D) all of the above

Last Answer : (D) all of the above

The helix angle in case of closely coiled helical spring is (A) less than 5° (B) 5° to 7° (C) 7° to 10° (D) more than 10°

Description : The helix angle in case of closely coiled helical spring is (A) less than 5° (B) 5° to 7° (C) 7° to 10° (D) more than 10°

Last Answer : (D) more than 10°

The helix angle in case of closely coiled helical spring is (A) less than 10° (B) 10° to 15° (C) 15° to 20° (D) more than 20°

Description : The helix angle in case of closely coiled helical spring is (A) less than 10° (B) 10° to 15° (C) 15° to 20° (D) more than 20°

Last Answer : (A) less than 10°

Torsional shear stresses are induced in the spring wire when (A) spring is under compression (B) spring is under tension (C) both (A) and (B) (D) none of the above

Description : Torsional shear stresses are induced in the spring wire when (A) spring is under compression (B) spring is under tension (C) both (A) and (B) (D) none of the above

Last Answer : (C) both (A) and (B)

In compression springs, the external force tends to (A) shorten the spring (B) lengthen the spring (C) both (A) and (C) (D) keep the length same

Description : In compression springs, the external force tends to (A) shorten the spring (B) lengthen the spring (C) both (A) and (C) (D) keep the length same

Last Answer : (A) shorten the spring

In which of the following item(s), spring is used to store energy. (A) clocks (B) toys (C) circuit breakers (D) all of the above

Description : In which of the following item(s), spring is used to store energy. (A) clocks (B) toys (C) circuit breakers (D) all of the above

Last Answer : (D) all of the above

The type of spring used to absorb and release energy in mechanical watches is (A) Helical extension spring (B) Multi-leaf spring (C) Spiral spring (D) Helical torsion spring

Description : The type of spring used to absorb and release energy in mechanical watches is (A) Helical extension spring (B) Multi-leaf spring (C) Spiral spring (D) Helical torsion spring

Last Answer : (C) Spiral spring

The spring operates (A) Within plastic limit (B) Within elastic limit (C) Within elasto-plastic limit (D) Within visco-elastic limit

Description : The spring operates (A) Within plastic limit (B) Within elastic limit (C) Within elasto-plastic limit (D) Within visco-elastic limit

Last Answer : (B) Within elastic limit

The type of spring used in vehicle clutches is, (A) Helical compression spring (B) Belleville spring (C) Both (A) and (B) (D) Helical torsion spring

Description : The type of spring used in vehicle clutches is, (A) Helical compression spring (B) Belleville spring (C) Both (A) and (B) (D) Helical torsion spring

Last Answer : (C) Both (A) and (B)

The type of spring used to achieve greater load carrying capacity within given space is (A) Spiral spring (B) Springs in series (C) Multi-leaf spring (D) Concentric springs

Description : The type of spring used to achieve greater load carrying capacity within given space is (A) Spiral spring (B) Springs in series (C) Multi-leaf spring (D) Concentric springs

Last Answer : (D) Concentric springs

When the helical torsion spring is subjected to torque, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress

Description : When the helical torsion spring is subjected to torque, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress

Last Answer : (C) Bending stress

The type of spring used to measure weights in spring balance is, (A) Helical extension spring (B) Multi-leaf spring (C) Spiral spring

Description : The type of spring used to measure weights in spring balance is, (A) Helical extension spring (B) Multi-leaf spring (C) Spiral spring

Last Answer : (A) Helical extension spring

When a helical spring is cut into two halves, the stiffness of each half spring will be, (A) Same as original spring (B) Double of original spring (C) Half of original spring (D) One fourth of original spring

Description : When a helical spring is cut into two halves, the stiffness of each half spring will be, (A) Same as original spring (B) Double of original spring (C) Half of original spring (D) One fourth of original spring

Last Answer : (B) Double of original spring

When the helical compression spring is subjected to axial compressive force, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress

Description : When the helical compression spring is subjected to axial compressive force, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress

Last Answer : (D) Torsional shear stress